Chemical Engineering Commons^™

Study And Improvement On Expansion Property Of Silicon Oxide, Wei-Chuan Qiao, Fang-Ru Li, Jin-Lin Xiao, Li-Juan Qu, Xiao Zhao, Meng Zhang, Chun-Lei Pang, Zi-Kun Li, Jian-Guo Ren, Xue-Qin He

Journal of Electrochemistry

The silicon-based anode materials have the potential to meet the ever-increasing demand for energy density in lithium-ion batteries market owing to their high theoretical specific capacity. Unfortunately, their commercialization was hindered by the continuous volume expansion. Herein, the expansion characteristics and corresponding mechanism of the silicon oxide and graphite-silicon oxide composites were investigated by in-situ displacement detection systematically. The results showed that the expansion property was improved by material process modifications. During the de/lithiation processes of graphite, the expansion ratio in 30% ~ 50% SOC changed little because of the small interlayer spacing variation of the intercalated graphite. …

Preparation And Properties Of Gcp-Supported Palladium Particles Composite Towards Electrochemical Ammonia Synthesis, Ying-Chao Wang, Zi-Zai Ma, Yi-Fan Wu, Xiao-Guang Wang

Journal of Electrochemistry

Ammonia (NH₃) plays an essential role in agriculture and modern industries. Electrochemical fixation of nitrogen (N₂) to ammonia (NRR) under ambient conditions with renewable electricity is a promising strategy to replace the industrial Haber-Bosch method. However, it usually suffers from extremely poor ammonia yield and low Faraday efficiency due to the poor electrocatalysts. Therefore, intensive studies have been devoted to developing efficient NRR catalysts till now. Among them, palladium (Pd) can capture protons in the aqueous phase to form stable α-PdH, which balances the competitive adsorption between nitrogen and protons as well as reduces the …

Optimum Biodiesel Production Using Ductile Cast Iron As A Heterogeneous Catalyst, Nada Amr El-Khashab, Marwa Mohamed Naeem, Mai H. Roushdy

Chemical Engineering

Biofuels production become a target for many researchers nowadays. Biodiesel is one the most important biofuels that are produced from biomass using economics and modern techniques. The ductile cast iron solid waste dust is one of the wastes produced by the cast iron industry which has a bad effect on the environment. This paper investigates the possibility of reusing ductile cast iron solid waste as a biodiesel heterogeneous catalyst used in its production from sunflower waste cooking oil. Four reaction parameters were chosen to determine their effect on the reaction responses. The reaction parameters are M:O ratio, reaction time and …

Characterization Of Gas Hydrate Formation And Its Impact On Slope Stability In Offshore Environments, Sulav Dhakal

LSU Doctoral Dissertations

Natural gas hydrates (NGH) are predominantly methane hydrates formed at high pressure and low temperature conditions typically in submarine sediments and permafrost. This dissertation is focused on the submarine methane hydrates formed by upward migration of free and dissolved gas. The methane gas stored within natural hydrates has more energy potential than all the combined oil and gas resources around the world. Numerical simulation of fluid flow, heat transport, and geomechanical stresses is used to characterize and evaluate the saturation, distribution, reservoir quality, and geohazards associated with hydrate-bearing sediments. Coupled thermo-hydro-mechanical (THM) simulation of hydrate formation, dissociation, and slope stability …

Virucidal N95 Respirator Face Masks Via Ultrathin Surface-Grafted Quaternary Ammonium Polymer Coatings, Mirco Sorci, Tanner D. Fink, Vaishali Sharma, Sneha Singh, Ruiwen Chen, Brigitte L. Arduini, Katharine Dovidenko, Caryn L. Heldt, Edmund F. Palermo, R Helen Zha

Michigan Tech Publications, Part 1

N95 respirator face masks serve as effective physical barriers against airborne virus transmission, especially in a hospital setting. However, conventional filtration materials, such as nonwoven polypropylene fibers, have no inherent virucidal activity, and thus, the risk of surface contamination increases with wear time. The ability of face masks to protect against infection can be likely improved by incorporating components that deactivate viruses on contact. We present a facile method for covalently attaching antiviral quaternary ammonium polymers to the fiber surfaces of nonwoven polypropylene fabrics that are commonly used as filtration materials in N95 respirators via ultraviolet (UV)-initiated grafting of biocidal …

Aerosol Capture And Coronavirus Spike Protein Deactivation By Enzyme Functionalized Antiviral Membranes, Rollie Mills, Ronald J. Vogler, Matthew Bernard, Jacob Concolino, Louis B. Hersh, Yinan Wei, Jeffrey Todd Hastings, Thomas D. Dziubla, Kevin C. Baldridge, Dibakar Bhattacharyya

Chemical and Materials Engineering Faculty Publications

The airborne nature of coronavirus transmission makes it critical to develop new barrier technologies that can simultaneously reduce aerosol and viral spread. Here, we report nanostructured membranes with tunable thickness and porosity for filtering coronavirus-sized aerosols, combined with antiviral enzyme functionalization that can denature spike glycoproteins of the SARS-CoV-2 virus in low-hydration environments. Thin, asymmetric membranes with subtilisin enzyme and methacrylic functionalization show more than 98.90% filtration efficiency for 100-nm unfunctionalized and protein-functionalized polystyrene latex aerosol particles. Unfunctionalized membranes provided a protection factor of 540 ± 380 for coronavirus-sized particle, above the Occupational Safety and Health Administration’s standard of 10 …

The Role Of Nickel And Brønsted Sites On Ethylene Oligomerization With Ni-H-Beta Catalysts, Gabriel V.S. Seufitelli, Jason J.W. Park, Phuong N. Tran, Anthony Dichiara, Fernando L.P. Resende, Rick Gustafson

Jasper Department of Chemical Engineering Faculty Publications and Presentations

The present work studies the adsorption of ethylene on Ni-H-Beta particles to unravel the roles of nickel and Brønsted sites in the catalytic oligomerization of ethylene. Three models (i.e., two based on the Cossee-Arlman mechanism and one based on the metallacycle mechanism) are examined in terms of the nature of the active sites and the adsorption mechanism involved in the ethylene coordination step. The results are consistent with the participation of two active sites in the formation of [Ni(II)-H]+ Cossee-Arlman centers and also suggest that ethylene dissociates upon adsorption on [Ni(II)-H]+ sites. Further characterization of Ni-H-Beta catalysts prepared at different …

A Circular Economy Approach To Improve E-Waste Recycling In California: Economic Potential And Policy Options, Kripa Shah

Master's Projects and Capstones

The higher consumption rates of electronic devices along with their short life cycles and few repair options poses a huge challenge for E-waste industries to manage them effectively. E-waste comprises of hazardous materials and toxic constituents that can affect the environment and public health through improper disposal. However, they also contain few valuable materials that, if recovered, can reduce the dependence on virgin raw materials. Circular economy has the potential to utilize these valuable materials and gain environment and socio-economic benefits. The research explains how the adoption of a circular economy approach can help improve the E-waste recycling in California …

Shape Memory Polymer Foaming With Tunable Interconnectivity Using Off-The-Shelf Foaming Components, Natalie Marie Petryk

Theses - ALL

The ability to tune pore structures of gas-blown polyurethane shape memory polymer (SMP) foams easily and safely could improve their outcomes as hemostatic dressings or tissue engineering scaffolds and overall commercialization efforts. Incorporating physical blowing agents into the polymer mix can be used to tune pore size and interconnectivity without altering foam chemistry. Enovate (HFC-254fa) is a commonly used physical blowing agent in gas-blown foams, but the Environmental Protection Agency (EPA) considers its use unacceptable because it is a hydrofluorocarbon that contributes to global warming. Here, off-the-shelf solvents accepted for use by the EPA, acetone, dimethyoxymethane (methylal), and methyl formate, …

Hybrid Double Network Cryogels Scaffold For Repair Of Local Cartilage Defect, Kaixiang Zhang

Theses - ALL

Trauma or repeated injury to the joint can result in focal cartilage defects, which significantly increase the risk of osteoarthritis. Cartilage being avascular has limited self-healing capacity. The current method for treating cartilage defects at early stages involves implantation of autologous chondrocytes with or without a scaffold through invasive surgery; however, invasive surgery can bring pain to patients and post-operative infection risks. Therefore, injectable and biodegradable biomaterials have piqued people's interest. In the current research, we designed a hybrid double network (DN) cryogel by combining multi-arm PEG acrylate and alginate as two networks and crosslinking them at -20°C. Through different …

Particle Formation And Thermal Radiation In Laminar Diffusion Flames With Applications To Energy And Materials, Phillip Irace

McKelvey School of Engineering Graduate Student Theses & Dissertations

Fossil fuels supply over 80% of the world’s primary energy, and if current policy and technology trends continue, global energy and energy-related carbon dioxide (CO2) emissions are predicted to increase for at least several decades owing to population and economic growth, leading to serious concerns regarding global warming. Natural gas releases less CO2 than other fossil fuels (e.g., coal and oil) and can help meet future CO2 emission targets. Natural gas combustion, however, has poor radiation heat transfer when compared to other fossil fuels owing to its low propensity for soot formation, making it difficult to use as a drop-in …

Engineering Metal-Oxide Interface By Depositing Zro2 Overcoating On Ni/Al2o3 For Dry Reforming Of Methane, Baitang Jin, Shiguang Li, Yuzi Liu, Xinhua Liang

Chemical and Biochemical Engineering Faculty Research & Creative Works

Zirconium oxide (ZrO₂) was deposited onto Ni/Al₂O₃ catalyst as overcoating by atomic layer deposition (ALD) for dry reforming of methane (DRM). High-temperature heating during H₂-reduction could transform the ALD-prepared ZrO₂ thin film to tetragonal phase and crack the encapsulating layer on Ni sites, which constructed a beneficial Ni-ZrO_x interface. Interfacial surface oxygen vacancies on ZrO₂ overcoating were induced by the partial reduction of ZrO₂ surface during high-temperature H₂ reduction, with the assistance of Ni. During DRM, the interfacial oxygen vacancies enhanced CO₂ activation by dissociating CO_{2 …}

Controlling The Emission Of Volatile Platinum Oxides To The Vapor Phase In Diesel Oxidation Catalysts, Arnab Ghosh

Nanoscience and Microsystems ETDs

Pt-based catalysts are used for the treatment of emissions from vehicles, particularly in Diesel oxidation catalysts (DOCs). Three-way catalysts are treated at temperatures ranging from 950℃-1050℃ while DOCs are aged at 800℃ for 50 hrs. At 800°C, Pt reacts with O₂ to form PtO₂ which has a high vapor pressure and can be transported through the vapor phase. These accelerated aging conditions lead to the formation of large Pt particles causing a loss of catalytic activity. In this thesis, we used model thin-film catalysts that made it possible to quantify the emission of Pt to the vapor phase …

Photocatalytic Degradation Of Organic Contaminants By Titania Particles Produced By Flame Spray Pyrolysis, Noah Babik

Theses and Dissertations

Advanced oxidation of organic pollutants with TiO2 photocatalysts is limited due to the wide bandgap of TiO2, 3.2 eV, which requires ultraviolet (UV) radiation. When nanosized TiO2 is modified by carbon doping, charge recombination is inhibited and the bandgap is narrowed, allowing for efficient photodegradation under visible light. Here, we propose a flame spray pyrolysis (FSP) technique to create TiO2. The facile process of FSP has been successful in preparing highly crystalline TiO2 nanoparticles. Using the same procedure to deposit TiO2 onto biochar, the photocatalyst was doped by the carbonaceous material. The morphology, crystalline and electronic structure of the FSP …

A Drift-Flux Model For Upward Two-Phase In Pipes With High Velocity Flows, Woochan Lee

LSU Doctoral Dissertations

This study proposes the evaluation and development of a drift-flux model for upward two-phase high-velocity flow in large diameter pipes. A case where the proposed model is applicable is WCD (Worst-Case-Discharge) calculations for offshore wells. WCD assumes relatively larger pipe diameters and higher flow rates than the flow experiments at laboratory conditions utilized to validate and develop most of the flow models available in the literature.

Most of the two-phase flow models describe flow regime transitions as discrete processes by assigning the required void fraction or velocity for each flow regime transition. Therefore, for each flow regime, flow-regime-dependent correlations or …

Receptor-Doped Organic Transistors: Transducing Anion Binding From Mixed Ionic-Electronic Transport, Anthony Benasco

Dissertations

Organic semiconductors based on π-conjugated polymers show remarkable properties such as high tolerance to structural defects, low processing temperature requirements, biocompatibility, ease of fabrication, and tunable properties. Conjugated polymers integrated into device arrays can exhibit collective properties sensitive to minor perturbations in the surrounding media. However, these devices rely on serendipitous sensitivity to the analyte of interest, and strategies for specific detection remain a considerable change. There remains a compelling, global need for technologies to monitor phosphate due to its prevalence in agricultural runoff, leading to fish kills and economic decline for commercial and recreational fisheries. The strong hydration energies …

Molecular-Level Control Over Ionic Conduction And Ionic Current Direction By Designing Macrocycle-Based Ionomers, Shyambo Chatterjee, Ehsan Zamani, Seefat Farzin, Iman Evazzade, Oghenetega Allen Obewhere, Tyler James Johnson, Vitaly Alexandrov, Shudipto Konika Dishari

Department of Chemical and Biomolecular Engineering: Faculty Publications

Poor ionic conductivity of the catalyst-binding, submicrometer- thick ionomer layers in energy conversion and storage devices is a huge challenge. However, ionomers are rarely designed keeping in mind the specific issues associated with nanoconfinement. Here, we designed nature-inspired ionomers (calix-2) having hollow, macrocyclic, calix[4]arene-based repeat units with precise, sub-nanometer diameter. In ≤100 nm-thick films, the in-plane proton conductivity of calix-2 was up to 8 times higher than the current benchmark ionomer Nafion at 85% relative humidity (RH), while it was 1−2 orders of magnitude higher than Nafion at 20−25% RH. Confocal laser scanning microscopy and other synthetic techniques allowed us …

Chiral Liquid Crystal Microdroplets For Sensing Phospholipid Amphiphiles, Sepideh Norouzi, Jose A. Martinez Gonzalez, Monirosadat (Sanaz) Sadati

Faculty Publications

Designing simple, sensitive, fast, and inexpensive readout devices to detect biological molecules and biomarkers is crucial for early diagnosis and treatments. Here, we have studied the interaction of the chiral liquid crystal (CLC) and biomolecules at the liquid crystal (LC)-droplet interface. CLC droplets with high and low chirality were prepared using a microfluidic device. We explored the reconfiguration of the CLC molecules confined in droplets in the presence of 1,2-diauroyl-sn-glycero3-phosphatidylcholine (DLPC) phospholipid. Cross-polarized optical microscopy and spectrometry techniques were employed to monitor the effect of droplet size and DLPC concentration on the structural reorganization of the CLC molecules. Our results …

Nuclear Energy As A Reliable And Safe Source Of Power Generation, Sarup Dhungana

Honors Theses

There is a high demand of energy for generating civil applicable power in the world and in the USA, correspondingly. The world has been consuming various sources to extract the power to meet its demands. Most of the power sources include renewable and non-renewable sources like fossil fuels, natural gas, coal, water, solar, wind, and nuclear power. Although most of these sources have many advantages in terms of their capacity and cost of production, nuclear power can be categorized as the emerging driving force in the United States and in the world for power generation, because of its reliability and …

Optimization Of An Ethylbenzene To Styrene Production Facility, John Michels

Honors Theses

The purpose of this case study is to optimize the design and production of an ethylbenzene-to-styrene manufacturing facility, Unit 500. Compared to the original base-case design, the optimizations presented in this document will save approximately $337 million dollars without compromising the production requirements or quality. Optimization of this process used net present value as an objective function, with changes centered around the reactors, but also the separation equipment and exchangers prior to separation, as those devices most directly controlled process stream contents and conditions. The second set of reactors was removed in favor of using one optimized set of reactors, …

Optimization And Analysis Of A Styrene Production Process, Alexis Kimpel

Honors Theses

The production of styrene from ethylbenzene in Unit 500 is designed to start up in 2024 and operate for 12 years after startup. The engineering team was tasked with designing the process, creating an economic model, and optimizing the net present value (NPV). The process was simulated in AVEVA PRO/II Simulation for the design process and to estimate the size of equipment. Parametric and topological optimization was performed subsequently on the unit operations in the process. The NPV was improved by $423M from a base case of -$919M to an optimized case of -$496M. The project is recommended to continue …

The Design And Economic Optimization Of A Warehouse Refrigeration System, Hannah Talbot

Honors Theses

The purpose of this project was to design a cool warehouse refrigeration system for Acme Frozen Foods, Inc located in Newark, New Jersey. The refrigeration system was used to cool eighteen 300,000 ft³ refrigerated units (200 ft x 100 ft x 15 ft), each requiring 200 cooling tons of refrigeration at a level of 0 F. The scope of this project included determining the appropriate refrigeration cycle, selecting the most desirable refrigerant, and temperature ranges to optimize the performance of the system. This project also considered the economic cost of the power needed to run the refrigerated units and …

Optimization Of Styrene From Ethylbenzene Case Study, Jabria Daria Thompson

Honors Theses

The following pages detail the optimization process of styrene from ethylbenzene in the Styrene Production Plant, Unit 500. There were two parts of the assignment, each with slightly different end goals. The goal of the first part of the assignment, was to create a process that would effectively and efficiently increase the negative Net Present Value (NPV) of the production plant. Procedures taken in this process included developing a working kinetic process simulation model and optimizing this model through unit operations and heat integration, as well as developing an accurate economic model that will be used to evaluate the proposed …

Energy And Resource-Saving Method For Enriching The Waste Water Purified Without Sufficient Purification With Oxygen, Dilobar Khurramova, Mukhtor Khurramov, Sharifa Ganieva, Zulqaynar Nazirov

CHEMISTRY AND CHEMICAL ENGINEERING

In order to implement a reliable and environmentally safe, economically viable method of wastewater enrichment, the goal is to develop an energy- and resource-saving method of oxygen enrichment of wastewater that has not undergone sufficient treatment. Cleaning is carried out in a tank, which is built using rock, which is an algal limestone. Limestone contributes to the improvement of the oxygen regime due to the “conservation” of organic matter in anoxic bottom layers and the acceleration of the process of photosynthesis of unicellular algae. Calcium carbonate is a reagent that provides not only automatic stabilization of water pH at 2/dm …

Kinetics Of Carboxymethylation Reaction Of Cellulose Samples With Different Degree Of Crystallinity, Ilkhom Goyibnazarov, Sherzod Yuldoshov, Abdushukhur Sarimsokov

CHEMISTRY AND CHEMICAL ENGINEERING

No abstract provided.

Mathematical Modeling Of Synthesis 4´,4´´-Di-(1-Methyl-1-Hydroxy-2-Phenylethynyl)-Dibenzo-18-Crown-6, Lyubov Kozinskaya, Dilorom Mirkhamitova

CHEMISTRY AND CHEMICAL ENGINEERING

The main goal of this study is the mathematical modeling of the optimal conditions for the synthesis of 4´,4´´-di-(1-methyl-1-hydroxy-2-phenylethynyl)-dibenzo-18-crown-6 by the least squares method. In the STAT program, iconograms of mathematical modeling of the synthesis and the dependence of the rate of formation of 4´,4´´-di-(1-methyl-1-hydroxy-2-phenylethynyl)-dibenzo-18-crown-6 on temperature and reaction time were obtained, the corresponding analytical dependencies are determined. Mathematical processing of the results of the synthesis of 4´,4´´-di-(1-methyl-1-hydroxy-2-phenylethynyl)-dibenzo-18-crown-6 was carried out, a system of linear equations was compiled using the matrix method. The average reaction rate and the optimum of the mathematical model were determined, and the experimental and calculated …

Optimization Of A Styrene Prodcution And Separation Process, Bryce Little

Honors Theses

A step wise optimization of Unit 500 was completed. Unit 500 is a planned ethylbenzene to styrene production plant that has a annual production goal of 100,000 metric tons of styrene. The cost of styrene on the market is $1,598. The base case of Unit 500 produced styrene at a cost of $2,650. Optimization was completed with an emphasis on parametric changes though material of construction and heat integration were also considered. The optimized Unit 500 design reduced the cost of styrene production to $2,035 per metric ton. While this represents a significant improvement on the base case cost, it …

Probing Myosin Ensemble Mechanics In Actin Filament Bundles Using Optical Tweezers, Omayma Al Azzam, Janie C. Watts, Justin E. Reynolds, Juliana E. Davis, Dana N. Reinemann

Faculty and Student Publications

Myosins are motor proteins that hydrolyze ATP to step along actin filament (AF) tracks and are essential in cellular processes such as motility and muscle contraction. To understand their force-generating mechanisms, myosin II has been investigated both at the single-molecule (SM) level and as teams of motors in vitro using biophysical methods such as optical trapping. These studies showed that myosin force-generating behavior can differ greatly when moving from the single-molecule level in a three-bead arrangement to groups of motors working together on a rigid bead or coverslip surface in a gliding arrangement. However, these assay constructions do not permit …

Optimization Of A Fluidized Bed Reactor For The Production Of Styrene From Ethylbenzene, Gregory Espenan

Honors Theses

In order to optimize Unit 500, a styrene production plant, the Net Present Value (NPV) was used as the objective function to ensure every optimization strategy had a positive economic effect. To optimize a chemical plant, it is important to note efficiency, economics, product specifications, and production requirements. The goal of this project was to make changes to the base case of Unit 500 to minimize the cost to produce styrene for an upstream unit. PRO/II was used to simulate various points in different unit operations throughout the process. The NPV was measured after each unit operation was simulated to …

A Data-Based Framework For Monitoring And Controlling Particulate Systems, Vidhyadhar Manee

LSU Doctoral Dissertations

One of the limitations of conventional monitoring tools in crystallization is the inability to deal with high solids concentration. Image-based monitoring, in which RGB images of the solution are captured and analyzed by an object detection software, has been a promising alternative. The software used in these tools primarily depends on hand-coded heuristics to distinguish between the signal and the noise. With the recent success of supervised deep learning, a newer paradigm has emerged in which the heuristics can be learnt from labeled images. This approach is founded on the idea that it is easier to develop labels for data …