Aerodynamics and Fluid Mechanics Commons^™

Hypersonic Heat Transfer Load Analysis In Star-Ccm+, Robert Comstock

Master's Theses

This thesis investigates the capabilities of STAR-CCM+, a Computational Fluid Dynamics (CFD) software owned by Siemens, in predicting hypersonic heat transfer loads on forward-facing surfaces. Results show that STAR-CCM+ predicted peak heat transfer loads within +/- 20% of experimental data on the leading edge of a delta wing design from the X-20 Dyna-Soar program with 73^o of sweep. Steady-state laminar simulations were run as replications of wind tunnel tests documented in NASA CR-535, a NASA technical report that measured and studied the hypersonic pressure and heat transfer loads on preliminary X- 20 wing designs across a wide range of …

Numerical Analysis Of A Circulation Control Wing, Luke W. Bodkin

Master's Theses

The objective of this thesis was to develop an experimental method to research circulation control wings using numerical analysis. Specifically, it is of interest to perform 3D wind tunnel testing on a circulation control wing in the Cal Poly Low Speed Wind Tunnel (CPLSWT). A circulation control wing was designed and analyzed to determine the feasibility of this testing.

This study relied on computational fluid dynamics (CFD) simulations as a method to predict the flow conditions that would be seen in a wind tunnel test. A CFD simulation was created of a wing model in a wind tunnel domain. Due …

Celebrating 90-Orbits Around The Sun, Stafford Air & Space Museum

Programs

In celebration of the 90th birthday of Oklahoma astronaut and aerospace legend, Gen. Thomas P. Stafford, the Stafford Air & Space Museum in Weatherford, Oklahoma is offering free admission on September 17th, 2020.

Unless stated otherwise within this repository collection, all materials are shared under the following Creative Commons license: [Creative Commons Attribution-NonCommercial 4.0 International License].

Resonant Triad Interactions In One And Two-Layer Systems, Malik Chabane

Dissertations

This dissertation is a study of the weakly nonlinear resonant interactions of a triad of gravity-capillary waves in systems of one and two fluid layers of arbitrary depth, in one and two-dimentions. For one-layer systems, resonant triad interactions of gravity-capillary waves are considered and a region where resonant triads can be always found is identified, in the two-dimensional wavevector angles-space. Then a description of the variations of resonant wavenumbers and wave frequencies over the resonance region is given. The amplitude equations correct to second order in wave slope are used to investigate special resonant triads that, providing their initial amplitude …

Studies Of Two-Phase Flow With Soluble Surfactant, Ryan Peter Atwater

Dissertations

Numerical methods are developed for accurate solution of two-phase flow in the zero Reynolds number limit of Stokes flow, when surfactant is present on a drop interface and in its bulk phase interior. The methods are designed to achieve high accuracy when the bulk Péclet number is large, or equivalently when the bulk phase surfactant has small diffusivity

In the limit of infinite bulk Péclet number the advection-diffusion equation that governs evolution of surfactant concentration in the bulk is singularly perturbed, indicating a separation of spatial scales. A hybrid numerical method based on a leading order asymptotic reduction in this …

Aeroacoustics Of Supersonic Jet Interacting With Solid Surfaces And Its Suppression, Seyyed Saman Salehian

Doctoral Dissertations and Master's Theses

The noise generated by supersonic jet is of primary interest in the high-speed flight. In several flight conditions jet exhaust of the propulsion system interacts with solid surfaces. For example, jet impingement on ground for a rocket lift-off, or interactions influenced by the integration of the engine with the airframe. Such complex applications require consideration of the role of acoustic-surface interactions on the noise generation of the jet and its radiation. Numerical analysis of supersonic jet noise involved in these scenarios is investigated by employing Hybrid Large Eddy Simulation – Unsteady Reynolds Averaged Simulation approach to model turbulence.

First, the …

Analysis Of Body And Tail Of A Flapping Drone, Yuan Chai

Student Works (2020-2029)

The Micro Aerial Vehicle (MAV) is a kind of unmanned aerial vehicle with a small size, which has a unique performance that larger aircrafts do not have. MAV can fly in confined spaces and perform hover, forward flight, etc. The flapping wing micro aerial vehicle is one type of flight imitates the insects (birds), which can fly based on the flapping wing. Compared with fixed-wing aircraft, the flapping wing micro aerial vehicle (FWMAV) has a smaller volume, lighter weight, and higher flight efficiency. FWMAV can be largely used in military and civil applications. In this project, the flapping drone is …

Fluid Flow Analysis Of Low-Altitute Agricultural Uav Pesticide Spraying Device, Dan Han

Student Works (2020-2029)

The nozzle is an important part of the drone pesticide spraying device. The quality of the nozzle directly affects the atomization performance. Fan nozzles are widely used in the field of plant protection in agriculture, forestry, pest control, and weed removal. When using drones to spray pesticides, the spraying velocity, the spraying range of the pesticides, and the atomized particle size are all key factors that directly affect the efficiency of pesticide use. This paper uses SOLIDWORKS and ANSYS software to design and simulate. The boundary conditions are kept the same, and the influence of the nozzle's grooving angle (α), …

Analysis Of One Way Valve Mechanism For Wings Of A Flapping Drone, Xinchen Deng

Student Works (2020-2029)

The flapping drone is one type of MAVs which is defined as a miniature unmanned aerial vehicle that is inspired by flying birds and insects. Flapping wings can make a perfect combination of thrust and lift by flapping up and down with full usage of unsteady air. The flapping drone has the advantages of high maneuverability and a special lift generation mechanism. Compared with rotary-wing or fixed-wing MAV, it is smaller, lighter, and has higher flight performance. It can quickly change the flight direction and flight speed by control the flapping frequency and it is the only flight mode that …

Investigations Of Air-Water Multiphase Flow In Tubes: Computational Fluid Dynamics, Wei Hong Goo

Student Works (2020-2029)

Mixing is a very crucial process in many industries, such as food processing industry, minerals processing industry, petrochemicals and refining industry, pulp and paper industry, polymer industry, pharmaceuticals industry and many more. There are different types of mixing, such as liquid-gas mixing, liquid-liquid mixing, solid-liquid mixing and many more. The definition of multiphase flow is the simultaneous flow of materials with multiple thermodynamic phases. A lot of process industries require multiphase flows during operation. Bubbly flow is defined as the flow of liquids that contains dispersed gas bubbles. One of the main applications of multiphases flows and bubbly flows is …

Dynamic Effects Of Inertial Particles On The Wake Recovery Of A Model Wind Turbine, Sarah E. Smith

Dissertations and Theses

Impacting particles such as rain, dust, and other debris can have devastating structural effects on wind turbines, but little is known about the interaction of such debris within turbine wakes. This study aims to characterize behavior of inertial particles within the turbulent wake of a wind turbine and relative effects on wake recovery. Here a model wind turbine is subjected to varied two-phase inflow conditions, with wind as the carrier fluid (Re_λ = 49 - 88) and polydisperse water droplets (26 to 45µm in diameter) at varied concentrations (Φ_v=0.24 x 10^-5 - 1.3 …

Droplet Ejections During Wet Lab Operations Aboard Spacecraft, Caleb Cushman Turner

Dissertations and Theses

The breakup and rupture of liquid bridges, thin films, bubbles, droplets, rivulets, and jets can produce satellite droplets that are subsequently ejected into their surrounding environment. For example, when any solid object is withdrawn from a liquid bath, the formation of an ever-thinning columnar liquid bridge eventually ruptures along the axis of the bridge. When rupture occurs under typical pipetting conditions the dynamics governing the rupture almost always produce at a minimum a satellite droplet. When these droplets occur they are often too small and too fast to be observed by the human eye. In a terrestrial environment they are …

Contributions To The Understanding Of Ship Airwakes Using Advanced Flow Diagnostic Techniques, Dhuree Seth

Doctoral Dissertations and Master's Theses

The objective of this research was to better characterize the complex, three dimensional, unsteady aerodynamic flows produced by the superstructure of a ship, which is referred to as an airwake. This problem is relevant and important because the turbulent airwake significantly and adversely affects the ability for rotorcraft to operate safely from the decks of Navy ships. To this end, a series of wind tunnel measurements were performed on the SFS2 simplified frigate shape, which has a flight deck at its stern. The measurements were performed with and without a simulated atmospheric boundary layer (ABL), which included the aerodynamic scaling …

Rotor-On-Rotor Aeroacoustic Interactions Of Multirotor In Hover, Eduardo Alvarez, Austin Schenk, Tyler Critchfield, Andrew Ning

Faculty Publications

Multirotor configurations introduce complicated aerodynamic and aeroacoustic interactions that must be considered during aircraft design. In this paper we explore two numerical methods to model the acoustic noise caused by aerodynamic rotor-on-rotor interactions of rotors in hover. The first method uses a conventional mesh-based unsteady Reynolds-average Navier-Stokes (URANS) solver, while the second consists of a meshless Lagrangian solver based on the viscous vortex particle method (VPM). Both methods are coupled with an aeroacoustics solver for tonal and broadband noise predictions. Noise predictions are validated for single and multi-rotor configurations, obtaining with the VPM a similar accuracy than URANS while being …

Narmax Identification Based Closed-Loop Control Of Flow Separation Over Naca 0015 Airfoil, Sohaib Obeid, Goodarz Ahmadi, Ratneshwar Jha

Henry M. Rowan College of Engineering Departmental Research

A closed-loop control algorithm for the reduction of turbulent flow separation over NACA 0015 airfoil equipped with leading-edge synthetic jet actuators (SJAs) is presented. A system identification approach based on Nonlinear Auto-Regressive Moving Average with eXogenous inputs (NARMAX) technique was used to predict nonlinear dynamics of the fluid flow and for the design of the controller system. Numerical simulations based on URANS equations are performed at Reynolds number of 106 for various airfoil incidences with and without closed-loop control. The NARMAX model for flow over an airfoil is based on the static pressure data, and the synthetic jet actuator is …

A Parametric Study Of Formation Flight Of A Wing Based On Prandtl's Bell-Shaped Lift Distribution, Kyle S. Lukacovic

Master's Theses

The bell-shaped lift distribution (BSLD) wing design methodology advanced by Ludwig Prandtl in 1932 was proposed as providing the minimum induced drag. This study used this method as the basis to analyze its characteristics in two wing formation flight. Of specific interest are the potential efficiency savings and the optimal positioning for formation flight. Additional comparison is made between BSLD wings and bird flight in formation.

This study utilized Computational Flow Dynamics (CFD) simulations on a geometric modeling of a BSLD wing, the Prandtl-D glider. The results were validated by modified equations published by Prandtl, by CFD modeling published by …

A Study Of The Design Of Adaptive Camber Winglets, Justin J. Rosescu

Master's Theses

A numerical study was conducted to determine the effect of changing the camber of a winglet on the efficiency of a wing in two distinct flight conditions. Camber was altered via a simple plain flap deflection in the winglet, which produced a constant camber change over the winglet span. Hinge points were located at 20%, 50% and 80% of the chord and the trailing edge was deflected between -5° and +5°. Analysis was performed using a combination of three-dimensional vortex lattice method and two-dimensional panel method to obtain aerodynamic forces for the entire wing, based on different winglet camber configurations. …

Development Of A State-Space Aeroelastic Model Of A Flexible T-Tail Aircraft For Flutter Analysis, Patrick S. Downs

Doctoral Dissertations and Master's Theses

Flutter prediction is an important part of the preliminary design process of any new aircraft. Current analysis methods include coupled fluid structure interaction codes and doublet lattice panel codes. The computation resources and time required for CFD solutions makes them unattractive for preliminary design and doublet lattice models require considerable pre and post processing to provide satisfactory results. Thus, a process for developing an analytical model to facilitate rapid design changes and the implementation of active control systems is the main motivation of this thesis. An analytical model is developed by first deriving the equations of motion of the structure …

A Study Of The Utilization Of Panel Method For Low Aspect Ratio Wing Analysis, William Barton D. Newey

Master's Theses

This study demonstrates the applicability of using a modified application strategy of panel method to analyze low aspect ratio wings at preliminary design phases. Conventional panel methods fail to capture the leading edge vortex (LEV) that is shed by wings with low aspect ratios, typically below 2 depending on planform. This aerodynamic phenomenon contributes to a significant amount of the lift of these wings and the result is a drastic underestimation of the lift characteristics when analyzed by conventional panel method. To capture the effect of the leading edge vortex, a panel method code was used with an extended definition …

Conceptual Design Of A South Pole Carrier Pigeon Uav, Kendrick M. Dlima

Master's Theses

Currently, the South Pole has a large data problem. It is estimated that 1.2 TB of data is being produced every day, but less than 500 GB of that data is being uploaded via aging satellites to researchers in other parts of the world. This requires those at the South Pole to analyze the data and carefully select the parts to send, possibly missing out on vital scientific information. The South Pole Carrier Pigeon will look to bridge this data gap.

The Carrier Pigeon will be a small unmanned aerial vehicle that will carry a 30 TB solid-state hard drive …

A Study Of The Standard Cirrus Wing Lift Distribution Versus Bell Shaped Lift Distribution, William H. Bergman

Master's Theses

This thesis discusses a comparison of the differences in aerodynamic performance of wings designed with elliptical and bell-shaped lift distributions. The method uses a Standard Cirrus sailplane wing with a lift distribution associated with the induced drag benefits of an elliptical distribution (span efficiency = 0.96) as the basis of comparison. The Standard Cirrus is a standard class sailplane with 15-meter wingspan that was designed by Schempp-Hirth in 1969. This sailplane wing was modeled and analyzed in XFLR5, then validated against existing wind tunnel airfoil data, and Standard Cirrus flight test data. The root bending moment of the baseline wing …

Development And Application Of Elliptic Blending Lag K-Omega Sst Standard And Wall-Distance-Free Turbulence Model, Wenjie Shang

McKelvey School of Engineering Graduate Student Theses & Dissertations

In recent decades, Computational Fluid Dynamics (CFD) has become the most widely used technology to understand the fundamental complex fluid dynamics of turbulent flows as well as for modeling of turbulent flows in industrial applications. In industrial applications, the widely used methodology is to solve Reynolds-Average Navier-Stokes Equations (RANS) equations in conjunction with a turbulence model since it strikes a balance between accuracy and computational cost compared to other high fidelity approaches namely the Large Eddy Simulation (LES) and Direct Numerical Simulation (DNS), There are a large number of turbulence models proposed in past five decades, majority of them are …

Wind Tunnel Wake Generator, Carl Pickl, James L. Rutledge, Marc D. Polanka, Brian Crabtree, Christopher Harkless

AFIT Patents

A wake generator for placement in a wind tunnel between a wind source and a test object includes a first frame member having a first track formed thereon, where the first track has a shape including a first side that is substantially rounded and a second side that is substantially flat. The wake generator may include a mounting plate disposed within a perimeter of the first track, where the mounting plate is rotatable relative to the first frame member about a first axis. The wake generator may also include a plurality of bars slidably engaged to the mounting plate and …

Delaying Flow Separation Using Piezoelectric Actuators, Kenechukwu Okoye

Honors Theses

Flow separation causes aircraft to experience an increase in drag degrading their aviation performance. The goal of the study was to delay flow separation on an airfoil by embedding a high-frequency translational piezoelectric actuator along the surface of the airfoil. This study investigated the extent to which the high-frequency translational piezoelectric actuator displaces the flow separation downstream or prevents it altogether utilizing a fog-based flow visualization experiment. The actuators with two actuation surfaces were embedded on the suction surface of an Eppler 862 airfoil model and placed in a low-speed wind tunnel. Dry ice fog streams were injected into the …

Potential Of Hydrodynamic Metamaterial Cloak For Drag Reduction, Rong Zou

McKelvey School of Engineering Graduate Student Theses & Dissertations

Metamaterials are rationally designed artificial materials composed of tailored functional building blocks densely packed into an effective material. While metamaterials historically are primarily thought to be associated with negative index of refraction and invisibility cloaking in electromagnetism or optics, it turns out that the simple metamaterial concept also applies to many other areas of physics namely the thermodynamics, classical mechanics including elastostatics, acoustics, fluid dynamics and elastodynamics, and in principle also to the quantum mechanics. The goal of this thesis is to introduce and evaluate the potential of a hydrodynamic metamaterial cloak for drag reduction of objects in viscous flow. …

Active Drag Reduction Of Ground Vehicles Using Air-Jet Wheel Deflectors, Kaloki Nabutola

Doctoral Dissertations and Master's Theses

Seven turbulence models were used to simulate the flow within the wheelhouse of a simplified vehicle body. The performance of each model was evaluated by comparing the aerodynamic coefficients obtained using computational fluid dynamics (CFD) to data collected from wind tunnel experiments. The performance of large eddy simulation (LES) and detached eddy simulation (DES) was largely dependent on the time step and grid size to accurately resolve turbulent eddies. The standard k-e, realizable k-e, k-w, DES, and LES all trended towards a drag coefficient which was 20% lower than the experimental value. In all numerical cases, the lift coefficient was …

Analysis Of Local Convection Heat Transfer Rates Of Supercritical Carbon Dioxide In Tubes, Yang Chao

Doctoral Dissertations and Master's Theses

Numerical investigation on thermodynamic characteristics of pure supercritical carbon dioxide (𝑆𝐶𝑂2) and mixtures of Helium and 𝑆𝐶𝑂2 in horizontal straight tubes with diameter of 6mm under cooling and heating conditions is carried out by using SST 𝑘 − 𝜔 turbulence model. The computations are conducted at operating pressure of 8MPa with various operating conditions. Simulations are conducted by using the latest poly-hexcore mesh method in ANSYS FLUENT 19.2 and tetrahedral mesh method in CFX 19.2, results and solving time are compared. The effect of heat flux, mass flux, inlet temperature and buoyancy on heat transfer performance are studied, pressure drop …

Dmd And Pod Modal Analysis For Store Separation, Nicholas Peters

Doctoral Dissertations and Master's Theses

Store separation from aircraft and spacecraft has historically been a critical and in some cases fatal issue for the aerospace industry. Given the severity of the issue much effort has been spent on the development of processes to identify failure flight conditions for store separation. The processes currently used for identifying potential failure conditions however are both resource intensive and iterative processes. A potential remedy to reducing resource use and improve turn around time in this process is the implementation of a mode based reduced order model (ROM) for modeling store separation. The objective of this study was to first …

Helios And Tenasi Results For The Workshop For Integrated Propeller Prediction, Aaron Crawford

Honors Theses

Beginning in 2018, the AIAA began the workshop for integrated propeller prediction. This effort was intended to bolster the CFD prediction capabilities of the aerospace community due to a resurgent interest in propeller driven vehicles for electric applications. The test bed for this workshop is the NASA X-57, a model of which was experimentally tested in the Lockheed Martin Low Speed Wind Tunnel in January 2019. Using the 3D scanned geometry provided by the workshop a mesh was created and all priority one simulations were performed using two flow solvers. The flow solvers used were Helios, developed by the ADD …

Studies Of Oval Tube And Fin Heat Exchangers, Phillip Nielsen

Undergraduate Student Works

Heating Ventilation and air-conditioning (HVAC) is a system which changes the temperature of the surroundings for the purposes of cooling or heating. This system requires energy to maintain a temperature difference from the outside temperature. Optimizing the flow over the evaporator coils is one way to increase the cooling efficiency. This will reduce the power required to have a sustainable system. Optimizing the flow to increase the energy transfer between the fins and the incoming air could result in a greater Coefficient of Performance (COP). This will be achieved by changing the geometry of the tubes for greater interaction with …