Aerodynamics and Fluid Mechanics Commons^™

Computer Based Modeling For Small E-Vtol Propeller Performance, Ege Konuk

Mechanical & Aerospace Engineering Theses & Dissertations

The emerging field of urban air mobility (UAM) offers a novel transportation method for civil, commercial, and military applications. Vertical take-off and landing (VTOL) configurations present challenges for performance prediction during crucial flight operations. An advanced computational framework for predicting propeller performance in electric vertical takeoff and landing (eVTOL) aircraft during transition flight is essential for future concept designs. This research extends the Blade Element Momentum Theory (BEMT) to model propeller behavior at high incidence angles, crucial for eVTOL operation.

The study begins with a review of tilt-wing/rotor configurations for eVTOLs and tackles the complex aerodynamic phenomena associated with rotors …

Studies Of Flowfields And Dynamic Stability Characteristics Of A Quadrotor, Engin Baris

Mechanical & Aerospace Engineering Theses & Dissertations

Electric multirotor air vehicles have become a pervasive technology and research topic in industry, academia, and daily life, and small quadrotors are one of the most preferred designs in the multirotor marketplace. However, the configuration of the quadrotors makes aerodynamic interaction effects one of the key factors of the vehicle performance in both hover and non-axial forward flight conditions.

In the present work, aerodynamic characteristics of the cross-configured small quadrotor in hover, edgewise, and maneuvering flight modes were investigated in detail by performing static and dynamic wind tunnel tests at various RPM levels, wind speeds, pitch and yaw angles, and …

Experimental And Computational Aerodynamic Studies Of Axially-Oriented Low-Fineness-Ratio Cylinders, Forrest Miller

Mechanical & Aerospace Engineering Theses & Dissertations

For the successful completion of atmospheric entry, descent, and landing (EDL) missions, a body geometry must be selected which provides favorable dynamic aerodynamic properties. The types of experimental facilities capable of collecting information on these properties are limited; however, their numbers are growing thanks to the continued work by the aerodynamics community. NASA Langley Research Center (LaRC) is conducting dynamic aerodynamic testing using a subsonic magnetic suspension and balance system (MSBS), with the end goal of implementing a supersonic MSBS facility at NASA Glenn Research Center. MSBSs are also currently used at the Institute of Fluid Science (IFS) at Tohoku …

A Study Of Asymmetric Supersonic Wind Tunnel Nozzle Design, Brittany A. Davis

Mechanical & Aerospace Engineering Theses & Dissertations

Achieving higher Mach numbers for private and commercial flight is a growing interest in the aerospace community. To qualify vehicles prior to flight, tests must be run in wind tunnels. Asymmetric wind tunnel nozzles are of continuing interest to the aerospace community due to their ability to change throat geometry, allowing for a range of Mach numbers to be achieved that encompasses all of the supersonic regime. The sliding block wind tunnel at Old Dominion University (ODU) is designed for a range of Mach numbers from about 1.8 to 3.5 but is limited to an upper limit of 2.8 by …

Analysis Of A Non-Equilibrium Vortex Pair As Aircraft Trailing Vortices, Manuel Ayala

Mechanical & Aerospace Engineering Theses & Dissertations

Shortly after the roll-up evolution of the vortex sheet behind the wings of an aircraft, a coherent counter-rotating vortex pair emerges. Presence of this vortex pair in the downstream of an aircraft, creates unsafe conditions for other aircraft, especially near airport runways. Fundamental knowledge of the physics that govern the formation, duration and dissipation of aircraft wake vortices is desirable in order to improve aircraft operational safety. This study uses non-equilibrium pressure theory to develop an accurate model describing the physical behavior of the vortex pair created by an aircraft in the early to mid-field vortex regime. An isolated aircraft …

A New Method For Estimating The Physical Characteristics Of Martian Dust Devils, Shelly Cahoon Mann

Mechanical & Aerospace Engineering Theses & Dissertations

Critical to the future exploration of Mars is having a detailed understanding of the atmospheric environment and its potential dangers. The dust devil is one of these potential dangers. The transport of dust through saltation is believed to be the driving mechanism responsible for Martian weather patterns. The two primary mechanisms for dust transport are dust storms and dust devils. Dust devils on Mars are a frequent occurrence with one in five so called giant dust devils being large enough to leave scars on the surface that are visible from space. Due to the thin atmosphere, winds of 60 mph …

Aerothermodynamic Analysis Of A Mars Sample Return Earth-Entry Vehicle, Daniel A. Boyd

Mechanical & Aerospace Engineering Theses & Dissertations

Because of the severe quarantine constraints that must be imposed on any returned extraterrestrial samples, the Mars sample return Earth-entry vehicle must remain intact through sample recovery. Vehicles returning on a Mars-Earth trajectory will attain velocities exceeding any that have been experienced by prior space exploration missions, with velocities approaching 14 km/s. Velocities as high as these will encounter significant heating during atmospheric re-entry to Earth.

The purpose of this study has been to systematically investigate the aerothermodynamic challenges that will result from a Mars sample return, Earth-entry vehicle design. The goal was to enable efficient estimation of maximum stagnation …

Thrust Prediction For A Rotor Operating In A Ship Airwake, Mathew Thomas

Mechanical & Aerospace Engineering Theses & Dissertations

This report details work performed at Old Dominion University focused on developing a thrust prediction capability for a rotor operating in a ship airwake. The study has built upon previous experimental work utilizing particle image velocimetry-based velocity field measurements to quantify the degree of coupling in a simplified rotor/ship airwake experiment. Using the velocity field data of the previous study, a database was built representing the volume over the landing deck. Rotor thrust was computed using blade element methods and compared to direct load cell measurements and to a superposed velocity field. Results show that the blade element method has …

Flight Dynamics Nonlinearity Assessment Across A New Aerodynamic Attitude Flight Envelope, Ayman Muhammad Abdallah

Mechanical & Aerospace Engineering Theses & Dissertations

A new asymmetric level aerodynamic attitude flight envelope is introduced in this dissertation. The aerodynamic attitude envelope is an angle of attack vs. sideslip angle region which describes the extent of where an aircraft can sustain a steady slipping horizontal flight condition. The new envelope is thus an extension of the more common speed-altitude symmetric level flight envelope. This new envelope can be used for design requirements, dynamic analysis, control synthesis, or performance comparison. Moreover, this envelope provides enhanced insight into trimability-controllability limitations within the aircraft design model. The aerodynamic attitude flight envelope is constructed for a six degree of …

Guidance And Navigation For A Spinning Projectile Using A Strapdown Seeker, Timothy J. Josey

Mechanical & Aerospace Engineering Theses & Dissertations

This thesis describes the derivation and implementation of an Extended Kalman Filter for the purpose of estimating the line of sight rates between a non-thrusting, guided projectile and a ground target. Line of sight rates are required signals to implement the proportional navigation guidance scheme. Using low-cost strapdown sensors, the line of sight rate is not directly measurable but is observable as shown in this thesis. The line of sight signal generated by strapdown seekers inherently includes projectile body motion, but with the use of a global positioning system and a strapdown inertial sensor suite, the seeker signal is transformed …

Laminar Deflagrated Flame Interaction With A Fluidic Jet Flow For Deflagration-To-Detonation Flame Acceleration, Joseph P. Mcgarry

Mechanical & Aerospace Engineering Theses & Dissertations

The concept of the Pulse Detonation Engine (PDE) has been of interest for centuries. The issue was originally studied to understand flame propagation in mine shafts after explosions due to methane buildup. The flames would travel down the shafts, transitioning to turbulent flames due to the roughness of the shaft walls, and accelerate to detonation, delivering powerful, destructive forces. The potential for efficient energy production was noticed, and the theory behind flame propagation was later applied to developing propulsion systems. Recently, researchers have begun to understand the full potential of PDEs to efficiently produce an immense amount of thrust due …

Use Of A Rolling Road System In Crosswind Conditions, Mau-Kuo Chen

Mechanical & Aerospace Engineering Theses & Dissertations

Wind tunnel testing continues to play an important role in vehicle aerodynamic development. Accurate results are strongly associated with whether the wind tunnel can closely simulate the on-road conditions, including the Reynolds number and all boundary conditions. Rolling road systems (or moving belts) have been a successful tool for many auto makers and racing teams to simulate the relative motion between the stationary vehicle model and the floor in the test section. The mechanism of the rolling road system is simple, but how it affects the adjacent flow field and how this flow interacts with the flow underneath the vehicle …

Design Advantages Of Skin Friction Drag Reduction Using Riblets, John Michael Gregory

Mechanical & Aerospace Engineering Theses & Dissertations

The research reported here has examined the potential improvements in overall aircraft performance that can result from integrating skin friction reduction technology, such as riblets, early in the aircraft design cycle. This study has shown that riblets can improve the payload capacity, increase the range, and improve performance of transport aircraft. If recent advances in fabrication techniques make it possible to create aluminum wing surfaces with integral riblet geometries, the applications could be widespread and the gains significant.

Active-Twist Rotor Blades Design, Analysis, And Testing, Andrew Randall Kreshock

Mechanical & Aerospace Engineering Theses & Dissertations

The subject of this thesis is the design, analysis, and experimental assessment of active-twist rotors. These active rotors use piezoelectric actuators embedded in the skins to twist the blade to reduce vibratory loads in the fixed system. First, the design and optimization of the twist response within the geometric and structural constraints of a rotor blade is presented. A parametric analysis is conducted varying the airfoil thickness, active-material placement, and structural plies to determine the maximum static twist response. A Macro-Fiber Composite (MFC), which is a fibrous piezoelectric device is used as the active material. Analyses of the cross-section are …

Characterization Of A Spiral Microfluidic Focusing Device For Continuous Single Cell Impedance-Based Cytometry Applications, Daniel Riley

Mechanical & Aerospace Engineering Theses & Dissertations

A major focus in the field of cell characterization is the quantification of cell dielectric properties in order to develop low-cost, portable microfluidic devices that can, among other things, perform point-of-care detection of rare diseases and complete blood counts. Impedance-based cytometry has become an advantageous tool to ascertain these properties, wherein it is important that cells pass through the same point in a channel cross-section one at a time to ensure accurate and repeatable readings. This study documents the assessment of an 8-loop 160 μm (W) x 80 μm (H) spiral microchannel used to focus 10 μm polystyrene particles. In …

Nonlinearity Index Analysis Of Periodic-Chaotic Stall-Spin Aircraft Motion, Daniel Paul Tapolcai

Mechanical & Aerospace Engineering Theses & Dissertations

This thesis explores the application of nonlinearity index theory to the nature of stalling and spinning aircraft motions. Nonlinear dynamic phenomena related to stall and spin have been a concern to flight engineers and pilots for generations. Considerable past work has been directed to detect and understand the cause and nature of these phenomena. Methods such as bifurcation analysis, Volterra expansion series, and nonlinear simulation are a few of the nonlinear approaches developed to study this topic. Traditionally, however, linear analysis is the most widely used approach for studying aircraft dynamical behavior under a given set of acceptable conditions. This …

Boundary Layer Measurements Related To Wind Tunnel Testing Of Riblets, Emrah Cinar

Mechanical & Aerospace Engineering Theses & Dissertations

With fuel economy being a significant factor in today's world of aviation, aircraft manufacturers have been looking into ways to decrease drag to save fuel. Drag reduction using riblets on wing and fuselage surfaces is . an area that has been studied extensively for the last two decades. In preparation for a larger project which will use several methods to simulate this phenomena, small scale research had to be done to find ways to generate similar conditions on scaled models in a low speed wind tunnel and examine boundary layer behavior.

In this project, boundary layer measurement techniques, such as …

Multidisciplinary Design Optimization Of Transonic Airfoil Sections Using Multiobjective Optimization And Computational Intelligence Tools, Amit A. Kulkarni

Mechanical & Aerospace Engineering Theses & Dissertations

The design of transonic airfoils for civil aviation applications has been a major engineering challenge in the last fifty years. This design problem arises due to the need to limit shock wave drag at a given transonic speed. In recent years, the requirement to reduce the levels of aircraft noise has started to affect the airfoil design process. The multidisciplinary aerodynamic shape optimization problem is treated in this thesis using a multi-objective approach. The objectives correspond to the design of transonic airfoil sections with low drag during cruise and low trailing edge noise levels during the approach condition. The optimization …

Multi-Element Airfoil Optimization Using Computational Fluid Dynamics, Mustafa Kubilay Ictuzer

Mechanical & Aerospace Engineering Theses & Dissertations

High-lift systems are frequently used on commercial transport aircrafts to obtain low speed performance, in terms of take-off and landing field lengths and approach speed. To maximize the take-off and landing performance within the critical restrictions required by the new generation transport wing designs, enhanced high-lift technologies are needed. Moreover, the economic realities faced by the airlines require a design that is mechanically simple and effective. These facts lead us to the optimization of the high lift systems.

Optimizing a high-lift system improves an aircraft's take-off and landing performance. The weight of the system, the advantages and the disadvantages all …

Analysis Of Wake Vortices Of A Medium Range Twin-Propeller Military Cargo Aircraft Using Statistically Designed Experiments, Burhan Sahin

Mechanical & Aerospace Engineering Theses & Dissertations

An experimental study was initiated to analyze the trajectories of the streamwise vortices behind the wing tip and flap of a medium range and propeller driven twin-engine military cargo aircraft. The model used for the experimental study was a generic, high wing and half model of a propeller driven aircraft and mounted within Old Dominion University's Low Speed Wind Tunnel where the wind tunnel flow speed was set to constant value of 9 m/sec. The main purpose of the study was to reach regression models for the motion and vorticity strength of both vortices under varying factors such as angle …

Aerodynamic Analysis Of An Urban Magnetic Levitation Vehicle, John Matthew Wells

Mechanical & Aerospace Engineering Theses & Dissertations

This thesis will detail the aerodynamic qualities of a magnetic levitation concept vehicle designed to be installed on Old Dominion University's campus. The vehicle is representative of a class of small, low-speed Maglev systems commonly referred to as Urban Maglev. A 1:12 scale model underwent testing in Old Dominion's low speed wind tunnel. Force and moment coefficients were measured over a wide range of yaw angles. Results give insight into crosswind effects and how these forces affect vehicle dynamics. An analysis of this type is important in understanding the ride quality and safety of the system. Force Coefficients range from …

Numerical Study Of Confined Flow Past An Airfoil Injector With A Planar Jet, Omar A. Alabbasi

Mechanical & Aerospace Engineering Theses & Dissertations

Vortex shedding from an airfoil injector in a channel is investigated by using a numerical solution for unsteady, two-dimensional, Navier-Stokes Equations. A second-order implicit finite-volume scheme is employed to solve the equations. The effect on vortex shedding of a planar jet injected from the rear of the injector is studied. The effect of the jet velocity on the vortex shedding and its drag and lift coefficients are also studied at different blockage ratios and Reynolds numbers for laminar flow. Initial results to validate previous numerical simulations are performed on a square cylinder with and without a planar jet. Good agreement …

Modeling And Simulation Of Coaxial Helicopter Rotor Aerodynamics, Murat Gecgel

Mechanical & Aerospace Engineering Theses & Dissertations

A framework is developed for the computational fluid dynamics (CFD) analyses of a series of helicopter rotor flowfields in hover and in forward flight. The methodology is based on the unsteady solutions of the three-dimensional, compressible Navier-Stokes equations recast in a rotating frame of reference. The simulations are carried out by solving the developed mathematical model on hybrid meshes that aim to optimally exploit the benefits of both the structured and the unstructured grids around complex configurations. The computer code is prepared for parallel processing with distributed memory utilization in order to significantly reduce the computational time and the memory …

Computational Solution Of Tail Buffet Response And Active Flow Control, Kaushik Laxmikant Joshi

Mechanical & Aerospace Engineering Theses & Dissertations

In this thesis, numerical simulation of the multidisciplinary method for prediction and control of vortex induced tail buffeting is studied using delta wing-single tail configuration. Flow conditions are chosen such that wing vortex cores experience vortex breakdown and the resulting wake flow impinges on the vertical tail. The aero/structure problem is solved sequentially using three sets of equations on a multi-block grid structure. To obtain aerodynamic loading on the tail, the fluid flow around the wing-tail assembly is computed by time-accurately solving unsteady, laminar, compressible Navier-Stokes equations using an implicit, upwind, flux-difference splitting finite volume scheme. Then the aeroelastic equations …

Experimental Investigation Of Active Control Of Bluff Body Vortex Shedding, Ilteris Koc

Mechanical & Aerospace Engineering Theses & Dissertations

Mean and fluctuating forces acting on a body are strongly related to vortex shedding generated behind it. Therefore, it is possible to obtain substantial reductions of at least the unsteady forces if vortex shedding is controlled or its regularity is reduced. While conventional active flow control methods are mainly concerned with direct interaction with, and alteration of, the mean flow about a body, modern techniques involve altering existing flow instabilities using relatively small inputs to obtain large-scale changes of mean flows. Aerodynamic flow control may be intended to delay or suppress boundary layer separation through creation of a boundary layer …

Active Control Of Nonlinear Panel Flutter At Supersonic Speed Using Aeroelastic Modes And Self-Sensing Piezoelectric Actuators Under Yawed Flow Angle, Myounghee Kim

Mechanical & Aerospace Engineering Theses & Dissertations

Suppression of nonlinear panel flutter at supersonic speeds has been investigated traditionally with system equations of motion in terms of in vacuo modal coordinates. For isotropic and symmetrically laminated orthotropic composite plates, the limit-cycle oscillations converged with six in vacuo natural modes at zero yaw angle. However, as laminated composite plates undergo the effect of an arbitrary yawed flow angle, complicated characteristics emerge when increasing the required in vacuo natural modes for an analysis of limit-cycle oscillations. In order to design an effective controller, the large number of modes should be reduced. As a result, the small number of modes …

Aerodynamic And Acoustic Investigations Of An Advanced Over-The-Wing Nacelle Transport Aircraft Configuration, Geoffrey A. Hill

Mechanical & Aerospace Engineering Theses & Dissertations

The transonic aerodynamic and low-speed acoustic characteristics of an advanced, Over-the-Wing Nacelle (OWN), subsonic transport configuration are assessed. The cruise aerodynamics of the OWN were analyzed using both inviscid Euler and viscous Navier-Stokes CFD. Results of the assessments are compared to a similar configuration with a more traditional Under-the-Wing Nacelle (UWN) installation and a similar reference Wing-Body Qualitative observations and quantitative drag computations are made for the three configurations at a cruise Mach number of0.78, an approximate altitude of35,000-ft, and a C_L, of 0.44. It was found that the OWN's novel inboard wing channel design is effective in …

Flow Control Of Airfoil At Post-Stall Conditions By Multiple Frequency Applied Saado Jets, A. Şamil Demirsöz

Mechanical & Aerospace Engineering Theses & Dissertations

Flow separation over lifting aerodynamic components, such as airfoils and wings, occurs during stall conditions which are caused by adverse changes (i.e.; high angle of attack, inflow conditions, etc.) in the operating conditions of aerodynamic components. During stall conditions, the flow over airfoil loses its momentum, creating high pressure zones on the upper surface of the airfoil and even a small increase in pressure causes the fluid particles to stop and separate to a low pressure zone. In order to eliminate the flow separation, the low momentum flow should be removed in order to maintain the high momentum and low …

Global Modeling Of Pitch Damping From Flight Data, Noah M. Favaregh

Mechanical & Aerospace Engineering Theses & Dissertations

Flight testing using a designed experiment was used to model pitch damping in the longitudinal short-period mode of an aircraft. Multi-step elevator maneuvers were flown at different angles of attack and power levels on an electrically powered, propeller-driven UltraStick 120 remotely controlled model A Central Composite Response Surface Design was used to select angle of attack and power levels for each maneuver. During post flight analysis it was discovered that power was not measured correctly for this purpose so advance ratio was selected as a replacement factor. Parameter estimation results for each maneuver were modeled globally using a single response …

Computational Sensing And Closed-Loop Active Flow Control Of Airfoil At Post-Stall Conditions, Volkan Kamaci

Mechanical & Aerospace Engineering Theses & Dissertations

Flow separation over lifting aerodynamic components, such as airfoils and wings, occurs during stall conditions which are caused by adverse changes (i.e. high angle of attack, inflow conditions, etc.) in the operating conditions of aerodynamic components. During stall conditions, the flow over airfoil loses its momentum, creating high pressure zones on the upper surface of the airfoil and even a small increase in pressure causes the fluid particles to stop and separate to a low pressure zone. In order to eliminate the flow separation, the low momentum flow should be removed in order to maintain the high momentum and low …