Aerodynamics and Fluid Mechanics Commons^™

Optimal Integrated Cfd-Gnc Model For Drag-Based Reentry Dynamics, Sebastian Lopez

Doctoral Dissertations and Master's Theses

This research focuses on optimizing the control of a drag-maneuvering, Starship-class re-entry vehicle by closely integrating high-fidelity aerodynamic data derived from Computational Fluid Dynamics (CFD) simulations, specifically using StarCCM+. The aerodynamic models, tailored to the unique geometry of a drag-maneuvering body, are seamlessly incorporated into a guidance, navigation, and control (GNC) framework. This integration enables closed-loop CFD simulations with real-time control feedback, allowing for direct analysis and optimization of vehicle stability, trajectory, and control demands throughout the re-entry process.

Building upon the work of Gaglio and Bevilacqua, this advanced CFD-GNC model introduces high-order aerodynamic effects, such as aerodynamic moments and …

Numerical Investigation Of Shock-Induced Deformation Of Bubble-Laden Droplets, Juan Roldan

Doctoral Dissertations and Master's Theses

Rain impact can be a source of surface erosion on hypersonic vehicles, and the severity of each impact depends on droplet velocity, mass, and final shape, all of which are set by how the droplet breaks up under shock loading. Real droplets are expected to carry entrained non-condensable gas (NCG) nuclei from their formation. This dissertation investigates whether the purely mechanical, pressure-driven response of these nuclei, independent of vaporization, is large enough to measurably alter the internal pressure field and early deformation of a shock-loaded droplet.

The droplet and surrounding gas are modeled with a compressible, diffuse-interface, axisymmetric Eulerian framework …

Aerodynamic And Acoustic Modeling For Evtol Rotor Noise Prediction, Daniella Bezuidenhout, Anastasios S. Lyrintzis, Vladimir V. Golubev

Doctoral Dissertations and Master's Theses

This thesis presents the development and validation of a methodology for predicting total acoustic emissions from a one-fifth scale electric vertical takeoff and landing (eVTOL) rotor in both hover and edgewise flight conditions. The approach couples sectional two-dimensional Reynolds-Averaged Navier-Stokes (2D-RANS) airfoil simulations with rotor loading predictions from the Comprehensive Hierarchical Aeromechanics Rotorcraft Model (CHARM), tonal noise calculations using the acoustic solver PSU-WOPWOP, and broadband noise predictions from the UCD-QuietFly framework. Boundary-layer inputs traditionally obtained from the viscous-inviscid solver, XFOIL, were replaced with higher-fidelity 2D-RANS results from OpenFOAM to better capture low-Reynolds-number flow physics, including laminar-turbulent transition and laminar separation …

Turbulent Plenum Jet-Crossflow Validation Via Subgrid Scale Model Variation And Upstream Forcing Under Dynamic Hybrid Rans-Les, Cole W. Mccallum

Mechanical Engineering Undergraduate Honors Theses

In modern gas turbine design, film cooling has become ubiquitous as a method for limiting heat transfer between high temperature gases post-combustion and the surface of downstream blades. This paper validates the use of various computational fluid dynamics techniques in recreating an experiment measuring adiabatic effectiveness over a surface downstream of a compound-angle N2 plenum jet incident on a turbulent-air boundary layer [1]. To do this, both RANS and Dynamic Hybrid RANS-LES (DHRL) methods are implemented and compared to previous research [2]. The latter method is then modified through implementation of a different subgrid scale (SGS) model and through addition …

Numerical Study Of Nutrient Mixing In Trabecular Bone In Microgravity, Disuse And Normogravity, Sagar Gharti

Doctoral Dissertations and Master's Theses

Mechanical loading is known to regulate bone remodeling by driving interstitial fluid flow which stimulates cells and drives nutrient transport within the trabecular network. In microgravity, the absence of mechanical stimulation or loading suppresses convective flow processes, causing diffusion-driven nutrient mixing and renewal, and accelerated bone loss. This thesis investigates how oscillation frequency and trabecular bone density jointly control nutrient mixing and wall shear stress within trabecular cavities.

A computational fluid dynamics (CFD) framework is developed in STAR-CCM+ using a soft-cap oscillation model that mimics cyclic compression. Three idealized trabecular morphologies are simulated across different frequencies to represent microgravity or …

Numerical And Experimental Evaluation Of A Simple, Low-Energy Lunar Volatile Separation Technology, Eleanor L. Zimmermann

Dissertations, Master's Theses and Master's Reports

In-situ resource utilization (ISRU) is the practice of finding, extracting, and using the local resources found on extraterrestrial bodies, such as the Moon and Mars. ISRU enables in-situ production of mission consumables—such as rocket fuel and potable water—which will be critical for establishing a sustainable human presence on the Moon, a goal NASA intends to accomplish by 2028 with the Artemis missions. The separation and liquefaction of locally extracted volatiles—such as water, CO₂, and Methane—is an essential component in lunar surface sustainability, but there are very few technologies being developed for this purpose. This report introduces the Radiative …

Thermal Management With Supercritical Carbon Dioxide Under Extreme Applications, Devon Hardy

Doctoral Dissertations and Master's Theses

A unique challenge in thermal system design is minimizing the power required to operate cooling systems while maintaining effective heat removal. Traditional cooling systems utilize single-phase fluids where the heat transfer mechanisms are well understood. To meet a variety of cooling demands, a range of technologies are available, including microchannel forced convection, jet impingement, porous media, nanofluids, pin fin arrays, and film cooling, each offering distinct advantages and limitations. While the performance of single- or two-phase cooling systems are generally predictable, in extreme thermal environments, new cooling solutions are needed to improve overall system efficiency and reliability.

Supercritical fluids, particularly …

Exploration Of Physics-Informed Grid Generation Technique For Wall-Modeled Les Using Eagle3d, Dominic Schneider

Doctoral Dissertations and Master's Theses

Wall-Modeled Large Eddy Simulation (WMLES) is an area of interest due to its ability to lower computational costs of LES. Even with the application of wall models, LES still proves to have practicality issues when it comes to use in industry, due to the expertise, time, and computational resources required. A novel technique for generating a lean, physics based WMLES grid is described.

The technique utilizes a RANS solution to extract turbulence information, user-specified values related to resolution of turbulent energy levels, acoustics waves, and shock waves, to generate a point cloud for producing a lean WMLES grid with in-house …

High-Fidelity Modeling Of Evtol Rotor Unsteady Aerodynamic And Aeroacoustic Response To Time-Harmonic Gust, Vadim Voropayev

Doctoral Dissertations and Master's Theses

The rapid emergence of Urban Air Mobility (UAM) demands accurate prediction and mitigation of noise generated by electric vertical take-off and landing (eVTOL) aircraft operating in complex urban environments. Among the various noise sources, the aerodynamic and acoustic response of rotors to unsteady inflow represents a major uncertainty in community-noise assessment and certification. This thesis investigates the aerodynamic and aeroacoustic behavior of a representative eVTOL rotor subjected to time-harmonic inflow disturbances, providing a detailed numerical framework to quantify how periodic gusts influence rotor performance, unsteady loading, and sound radiation.

The study employs a three-stage computational methodology using the open-source solver …

Analyzing The Impact Of Passive Techniques On Aircraft Wing Hysteresis: An Experimental And Numerical Study, Brendan Worton

Masters Theses

This study investigates the effects of passive flow control techniques on aerodynamic hysteresis primarily in NACA 2412 (cambered) and 0012 (symmetric) wings. Computational Fluid Dynamics (CFD) was used to design and evaluate three passive techniques, including outward-facing dimples, leading-edge tubercles, and rectangular vortex generators, prior to experimental validation. These techniques demonstrated improvements in aerodynamic performance in CFD simulations and were therefore selected for wind tunnel testing to analyze their aerodynamic performance and influence on hysteresis behavior. A custom, cost-effective experimental setup was designed and developed to facilitate efficient angle-of-attack control and data acquisition. It incorporates a three-axis force sensor, stepper …

Micro Wind Turbine - Modelling And Testing, Mohammad Uzair Bhati

All Theses

The global energy demand continues to rise as people consume more electricity to power their personal electronics, electric vehicles, and consumer products such as outdoor tools. To generate renewable energy, large scale solar and wind farms continue to receive the most commercial attention. However, portable wind energy turbines have the potential to generate sufficient power for cell phones and other electronic devices. There are two types of wind turbines, horizontal and vertical axis each having their pros and cons. Vertical-axis wind turbines are the main focus of this thesis, with a reduction in their form factor or size and portable …

Wind-Resilient Solar: Harnessing Cfd For Enhanced Load Estimation, Aly Mousaad Aly

Faculty Publications

Solar panels are a cornerstone of renewable energy infrastructure, playing a pivotal role in global sustainability efforts. To ensure their resilience and long-term viability, accurate wind load estimations are essential for designing supporting structures, which account for nearly 50% of their total cost. However, traditional building codes lack comprehensive guidance for solar panels, resulting in inconsistent estimations due to discrepancies in scaled wall-bounded wind tunnel testing methodologies. These inaccuracies pose safety risks, increase costs, and hinder adoption. Emerging technologies like computational fluid dynamics (CFD) simulations offer a promising alternative by enabling full-scale analysis under realistic conditions of complete turbulence. This …

Numerical Investigation Of Wind Disturbance Around A Multirotor Uav In Crosswind And Vertical Flight, Garrison Page

Theses and Dissertations--Mechanical and Aerospace Engineering

Uncrewed Aerial Vehicles (UAVs) are being increasingly utilized in a wide range of research applications, especially in meteorology. This is due to such factors as their ease of use, maneuverability compared to other forms of data collection, and for rotor- craft, the ability to hover. However, the rotorwash generated by UAVs can introduce significant disturbances, potentially affecting measurement accuracy from sensors. While several studies have investigated the rotorwash of individual UAVs utilizing Particle Image Velocimetry (PIV) and Computational Fluid Dynamics (CFD), there is limited exploration into how different rotor configurations and external wind conditions influence regions of turbulent flow around …

Development Of An Immersed Boundary Method-Wall Modeled Large Eddy Simulation Approach For Incompressible Flows And Aeroacoustic Predictions, John C. Higgins

Theses and Dissertations--Mechanical and Aerospace Engineering

The performance capabilities of rotorcraft have improved significantly in the past decade as both manned and unmanned rotorcraft become a larger part of future transportation systems. Private companies as well as various government offices have worked to develop capabilities ranging from transportation/package delivery to intelligence/surveillance to livestock monitoring. Their practicality in both rural and urban areas, however, is questionable due to the significant tonal and broadband noise which is produced by the rotors. Public acceptance of rotorcraft, namely small Unmanned Aerial Vehicles (sUAVs), in transportation systems is an issue largely associated with the noise generation and it's effect on nearby …

Direct Numerical Simulation Of Pulsating Flow In Curved Pipes: Insights Into Aortic Dissection In Humans, Gokul Anugrah Gopakumar

Theses and Dissertations--Mechanical and Aerospace Engineering

This dissertation investigates the hemodynamics of pulsating blood flow in curved vessels through direct numerical simulations (DNS), with the overarching aim of uncovering fluid dynamic mechanisms linked to the onset and progression of aortic dissection in humans. The work is structured in two parts: (i) fundamental studies in idealized geometries and (ii) preliminary investigations in patient-specific anatomies. In the first part, curved pipe models representing the aortic arch are used to isolate the effects of pulsation frequency, amplitude ratio, and curvature ratio on transitional and turbulent flow dynamics. The simulations reveal that curvature-driven centrifugal forces shift the peak velocity toward …

Impact Of Weather Systems On Uav Parameters Using Computational Fluid Dynamics, Saif Aljuhaishi, Yaseen K. Al-Timimi, Basim I. Wahab

Karbala International Journal of Modern Science

Since drones cannot fly in any kind of weather, they are not safe for time-sensitive activities. The study examines how the passage of weather systems in Iraq leads to the ban on drone flights, and how these weather conditions impact the aerodynamic forces of the drone. Hourly climate data for the study area were obtained from ECMWF ERA5 and CAMS in NetCDF format for four climate stations (Erbil, Baghdad, Rutbah, and Basrah). A ScanEagle drone was chosen for this study. The Python programming language was used to perform mathematical operations to calculate the ban on drone flights. ArcGIS 10.8 was …

Development Of Eagle3d Solver For Wall Modeled Les Of Transonic Flows, Spencer Moore

Doctoral Dissertations and Master's Theses

Wall modeled Large Eddy Simulation (LES) is an area of interest due to its ability to lower computational costs of LES simulation. Even with the application of wall models, LES still proves to have practicality issues when it comes to use in industry, due to the expertise, time, and computational resources required to get results. A case described by an axisymmetric transonic bump is explored utilizing the Embry-Riddle Aeronautical Universities in house unstructured finite volume multi-element CFD code, Eagle3D. Eagle3D, has been brought to the state of the art and validated against current research using this transonic bump case as …

Development Of On-The-Fly Quasi-Steady State Approximation For Chemical Kinetics In Cfd, Abhinav Balamurugan

Doctoral Dissertations and Master's Theses

This study analyzes the feasibility of On-The-Fly Quasi-Steady-State Approximation (OTF-QSSA) application for solving chemical kinetics within Computational Fluid Dynamics (CFD) simulations, aiming to reduce the computational demand of detailed mechanisms. An algorithm that dynamically identifies and designates Quasi-Steady-State (QSS) species at specific grid locations and instances during the simulation was developed. With this information, our method pseudo-delays the advancement of concentrations for these QSS species—effectively setting their rate of concentration change to zero for a set number iteration before updating using the detailed mechanism and thereby omitting the computationally intensive processes typically required for their calculation during those skipped iteration. …

Numerical Study In Wind Energy Extraction From Controlled Limit-Cycle Oscillations In Modified Glauert Airfoil, Ethan L. Deweese

Doctoral Dissertations and Master's Theses

Typically, wind energy harvesting technology employs wind turbines. Towards the goal of meeting increasing energy needs with renewable energy sources a novel wind energy harvesting scheme is considered, utilizing a modified Glauert (MG) airfoil experiencing aeroelastic limit cycle oscillation (LCO) from which energy may be extracted. Synthetic jet actuators (SJA)s are used along with the unique geometry of the MG airfoil to control flow separation and amplify the LCO and energy generation potential of the system. The discussed wind energy harvesting scheme could provide flexibility in allowing installations previously unsuitable to wind turbines due to geometric or low wind velocity …

Optimization Of High-Bypass Turbofan High-Pressure Compressor Blade – A Case Study, Adeel Khalid, Vlad Mandzyuk

The Kennesaw Journal of Undergraduate Research

This research determines the relationship between the High-Pressure Compressor (HPC) rotor blade design variables and compressor pressure ratio of a high bypass turbofan engine. Alterations in the HPC blades span, chord, taper, twist, number, and angle of incidence are performed and their effect on the HPC pressure ratio is observed. The objective is to determine key parameters that could maximize the performance of a high-pressure compressor for a given mission. Physics-based modeling, Computational Fluid Dynamics (CFD), and wind-tunnel testing are performed to compare and validate findings. Physics-based modeling is performed to serve as the benchmark for data obtained through other …

Winglet Vortex Optimization, Adeel Khalid, Anthony Gutierrez

The Kennesaw Journal of Undergraduate Research

The objective of this research is to determine the effect on aerodynamic performance due to changes of winglet design variables of the Boeing 737-700 aircraft. The various winglet types studied in this research include the blended, canted, wingtip fence and split scimitar. The variables include height, sweep angle, taper ratio, and inclination angle. These variables are altered in 5% increments from -15% to +15% of their original baseline values. Each altered winglet design only changes one variable at a time while keeping all other variables constant. The altered models are compared to the original by finding the aerodynamic efficiency through …

Experimentatal And Numerical Investigation Of Turbojet Engine Performance, Emissions, And Noise/Vibrations Using Jet-A And F24 Fuel, John W. Mcafee Jr

College of Graduate Studies: Theses & Dissertations

Drastic improvement in cost effectiveness of high-power computing resources has generated a great interest numerical simulation to reduce the overhead cost of engine manufacturing, maintenance, and environmental concerns of engine testing. To accomplish this goal, this research presents the differences between military F24 fuel and commercial aviation fuel Jet-A from a thermochemical and engine performance perspective. This experimental data was used to create and validate a numerical model of the engine used in the experiments fueled with both Jet-A and F24 fuels. The experimental data was collected using a research based single stage turbojet engine outfitted with many sensors for …

Towards Cfd Investigations Into Particulate Air Pollution Of A Desert Urban Environment, Prosun Roy

UNLV Theses, Dissertations, Professional Papers, and Capstones

This dissertation has explored computational fluid dynamics (CFD) techniques for studying particulate air quality in the Las Vegas urban area. The dissertation is based on three research tasks:

• • High time-resolution fenceline air quality sensing and dispersion modeling for environmental justice-centered source attribution. (Chapter 2)
• • Pollen dispersion and deposition in real-world urban settings: A computational fluid dynamic study. (Chapter 3)
• • Effects of urban canopy parameterizations on modeling pollen dispersion and exposure. (Chapter 4)

In Chapter 2, we investigate the facilitation of low-cost air quality sensors (LCAQS) and CFD technique on exposure assessment of environmental justice (EJ) communities and …

Computational Analysis Of Steady Hypersonic Flow Fields Of Nasa Benchmark Geometries Utilizing Ansys Fluent, Aidan Murphy

McKelvey School of Engineering Graduate Student Theses & Dissertations

The Hypersonic International Flight Research Experimentation (HIFiRE) program explores and advances hypersonic aerospace systems by developing a multitude of test flight geometries and conducting experimental test flights to obtain data for use in validation of computational models and results. This study focuses on computational validation of heat flux, and calculation of static pressure profiles, skin friction coefficient profiles, and flow contours. The flow fields studied are for Mach number 7.18 and angles of attack (α) of 0° & 2°. These flow fields include many compressible flow features such as an expansion wave at the intersection of the cone and flat …

Prediction & Active Control Of Multi-Rotor Noise, Samuel O. Afari

Doctoral Dissertations and Master's Theses

Significant developments have been made in designing and implementation of Advanced Air Mobility Vehicles (AAMV). However, wider applications in urban areas require addressing several challenges, such as safety and quietness. These vehicles differ from conventional helicopter in that they operate at a relatively lower Reynolds number. More chiefly, they operate with multiples of rotors, which may pose some issues aerodynamically, as well as acoustically. The aim of this research is to first investigate the various noise sources in multi-rotor systems. High-fidelity simulations of two in-line counter-rotating propellers in hover, and in forward flight conditions are performed. Near field flow and …

The Numerical Study Of Aeroacoustics Performance Of Wings With Different Wavelength Leading-Edge Tubercles, Youjie Zhang

Honors Undergraduate Theses

The leading-edge tubercle is a type of airfoil modification that inspired by the humpback whale. It was found that the aerodynamic performance of the wing would increase compared to the wing without tubercles. In the past several years, a lot of numerical and experimental studies have been accomplished to explore this leading-edge modification. Besides the aerodynamic performance change, this research explores the aeroacoustics behavior of airfoils with leading-edge tubercles. A numerical study based on Computational Fluid Dynamics (CFD) is established, and simulations using Star CCM are accomplished based on reasonable set-ups. The airfoil chosen to create the wing is NACA …

A Computational Fluid Dynamic Analysis Of Oxyacetylene Combustion Flow For Use In Material Response Boundary Conditions, Craig Meade

Theses and Dissertations--Mechanical and Aerospace Engineering

Oxyacetylene torches are used in the aerospace industry and research to test thermal protection system materials (TPS) due to their high flame temperatures and high heat flux capabilities. The purpose of this work is to determine a combustion model to accurately simulate the high temperature flow of an oxyacetylene torch. The flow conditions around a sample material can then be used as boundary conditions when modeling TPS material response. Two separate combustion models with equilibrium chemistry were investigated using ANSYS Fluent™; the Eddy-Dissipation Model, and the Partially Premixed model.The results of this study are compared to existing experiments for validation.

Optimization Of Ported Cfd Kernels On Intel Data Center Gpu Max 1550 Using Oneapi Esimd, Mohammad Zubair, Aaron Walden, Gabriel Nastac, Eric Nielsen, Christoph Bauinger, Xiao Zhu

Computer Science Faculty Publications

We describe our experience porting FUN3D’s CUDA-optimized kernels to Intel oneAPI SYCL.We faced several challenges, including foremost the suboptimal performance of the oneAPI code on Intel’s new data center GPU. Suboptimal performance of the oneAPI code was due primarily to high register spills, memory latency, and poor vectorization. We addressed these issues by implementing the kernels using Intel oneAPI’s Explicit SIMD SYCL extension (ESIMD) API. The ESIMD API enables the writing of explicitly vectorized kernel code, gives more precise control over register usage and prefetching, and better handles thread divergence compared to SYCL. The ESIMD code outperforms the optimized SYCL …

Computational Fluid Dynamics Modeling Of Hemodialysis In Patients With An Arteriovenous Fistula, Maximilian Roth

McKelvey School of Engineering Graduate Student Theses & Dissertations

With the advent of arteriovenous fistula (AVF) for use in hemodialysis, the anastomosis built for such use has become a central point of the study to understand the flow and wall shear stresses in such a system since very large wall shear stresses can lead to arterial/vein rupture. Considering the commonly used creation site of an anastomosis as connecting the radial artery to the cephalic vein, a model is created to calculate the wall shear stresses across various components of the system. The model depicts a connection of the specified vein and artery bridged together allowing the increase in blood …

A Study Of Asymmetric Supersonic Wind Tunnel Nozzle Design, Brittany A. Davis

Mechanical & Aerospace Engineering Theses & Dissertations

Achieving higher Mach numbers for private and commercial flight is a growing interest in the aerospace community. To qualify vehicles prior to flight, tests must be run in wind tunnels. Asymmetric wind tunnel nozzles are of continuing interest to the aerospace community due to their ability to change throat geometry, allowing for a range of Mach numbers to be achieved that encompasses all of the supersonic regime. The sliding block wind tunnel at Old Dominion University (ODU) is designed for a range of Mach numbers from about 1.8 to 3.5 but is limited to an upper limit of 2.8 by …