Aerodynamics and Fluid Mechanics Commons^™

Aeroelastic Simulation Of Shape Adaptive Wing, Allan Alfred Kozich Iii

Honors Undergraduate Theses

Morphing wings provide aerodynamic qualities that normal fixed wings cannot, such as the ability to improve endurance yet maintain maneuverability, overcome strong gusts, vibrations, and shocks, and handle both ideal flight for both high and low speeds. A critical application of the new generation of morphing wings is the ability to overcome and affect the onset flutter, a self-excited oscillatory instability that has led to the destruction of aircrafts. This work investigates aeroelastic behavior and measurement of a meta-material structured "smart" wing and its attempt to delay the effect of flutter. The variable wing tip model is analyzed through finite …

Numerical Study In Wind Energy Extraction From Controlled Limit-Cycle Oscillations In Modified Glauert Airfoil, Ethan L. Deweese

Doctoral Dissertations and Master's Theses

Typically, wind energy harvesting technology employs wind turbines. Towards the goal of meeting increasing energy needs with renewable energy sources a novel wind energy harvesting scheme is considered, utilizing a modified Glauert (MG) airfoil experiencing aeroelastic limit cycle oscillation (LCO) from which energy may be extracted. Synthetic jet actuators (SJA)s are used along with the unique geometry of the MG airfoil to control flow separation and amplify the LCO and energy generation potential of the system. The discussed wind energy harvesting scheme could provide flexibility in allowing installations previously unsuitable to wind turbines due to geometric or low wind velocity …

Aeroelastic Analysis Of Small-Scale Aircraft, Kent Roberts

Master's Theses

The structural design of flight vehicles is a balancing act between maximizing loading capability while minimizing weight. An engineer must consider not only the classical static structural yielding failure of a vehicle, but a variety of ways in which structural deformations can in turn, affect the loading conditions driving those deformations. Lift redistribution, divergence, and flutter are exactly such dynamic aeroelastic phenomena that must be properly characterized during the design of a vehicle; to do otherwise is to risk catastrophe. Relevant within the university context is the design of small-scale aircraft for student projects and of particular consideration, the DBF …

Development Of A State-Space Aeroelastic Model Of A Flexible T-Tail Aircraft For Flutter Analysis, Patrick S. Downs

Doctoral Dissertations and Master's Theses

Flutter prediction is an important part of the preliminary design process of any new aircraft. Current analysis methods include coupled fluid structure interaction codes and doublet lattice panel codes. The computation resources and time required for CFD solutions makes them unattractive for preliminary design and doublet lattice models require considerable pre and post processing to provide satisfactory results. Thus, a process for developing an analytical model to facilitate rapid design changes and the implementation of active control systems is the main motivation of this thesis. An analytical model is developed by first deriving the equations of motion of the structure …

Aeroelasticity Of Composite Plate Wings Using Hsdt And Higher-Order Fem, Justin A. Haught

Graduate Theses, Dissertations, and Problem Reports (ETD)

The aeroelasticity of composite wings is becoming an increasingly researched topic in aircraft design, as designers continue to replace aluminum alloy components with those made of composite materials because of their favorable strength-to-weight ratio, fatigue characteristics, and corrosion resistance. Additionally, the bending-torsion coupling exhibited by composite laminates readily allow for the aeroelastic optimization of an aerodynamic structure through the process of aeroelastic tailoring. Wings made of composites materials, however, are more vulnerable to shear deformation.

The objective of the present research is to study the divergence and flutter characteristics of composite plate wings using a higher-order shear deformation theory (HSDT) …

An Efficient Euler Method To Predict Shock Migration On A Straked Delta Wing Design, Dylan N. Hope

Theses and Dissertations

In support of the Air Force Office of Scientific Research, this project sought to identify the significance of nonlinear aerodynamic phenomena in regards to LCO of a straked delta wing design. Previous works include unsteady Navier-Stokes aeroelastic analysis of various wing designs and flight test of F-16 transonic LCO with interest focused on oscillatory SITES behavior. The research presented within this investigation further expanded the understanding of unsteady aerodynamics by performing aeroelastic analysis of a wing oscillated in pitch with an Euler-based, boundary layer coupled numerical method (ZEUS). The wing was tested for a multitude of LCO parameters such as …

The Effects Of Elasticity In The Foundation On The Flutter Of A Metallic High Aspect Ratio Wing, Horacio Esteban Sepic Kriskovich

Master's Theses - Daytona Beach

The goal of this thesis is to study the flutter characteristics of a metallic high-aspect ratio wing, with linearly varying chord across the semis-span, and a simulated elastic foundation. The general planform of the wing is similar to the one found in a High- Altitude Long-Endurance Uninhabited Aerial Surveillance Vehicle (HALE USAV).

The problem is studied using a simplified aerodynamic loading based on thin-airfoil theory, which is then combined with a Lagrangian formulation to solve the system as stationary. The wing has no control surfaces or external stores, and is modeled as a uniform beam with known mechanical properties, being …

Active Control Of Nonlinear Panel Flutter At Supersonic Speed Using Aeroelastic Modes And Self-Sensing Piezoelectric Actuators Under Yawed Flow Angle, Myounghee Kim

Mechanical & Aerospace Engineering Theses & Dissertations

Suppression of nonlinear panel flutter at supersonic speeds has been investigated traditionally with system equations of motion in terms of in vacuo modal coordinates. For isotropic and symmetrically laminated orthotropic composite plates, the limit-cycle oscillations converged with six in vacuo natural modes at zero yaw angle. However, as laminated composite plates undergo the effect of an arbitrary yawed flow angle, complicated characteristics emerge when increasing the required in vacuo natural modes for an analysis of limit-cycle oscillations. In order to design an effective controller, the large number of modes should be reduced. As a result, the small number of modes …

Dynamic Aeroelastic Analysis Of Wing/Store Configurations, Gregory H. Parker

Theses and Dissertations

Limit-cycle oscillation, or LCO, is an aeroelastic phenomenon characterized by limited amplitude, self-sustaining oscillations produced by fluid-structure interactions. In order to study this phenomenon, code was developed to interface a modal structural model with a commercial computational fluid dynamics program. LCO was simulated for a rectangular wing, referred to as the Goland⁺ wing. It was determined that the aerodynamic nonlinearity responsible for LCO in the Goland+ wing was the combination of strong trailing-edge and lambda shocks which periodically appear and disappear. This mechanism limited the flow of energy into the structure which quenched the growth of the flutter, resulting …

Suppression Of Post-Buckling Deflection And Panel-Flutter Using Shape Memory Alloy, Mohammad Tawfik Abo El So-Oud

Mechanical & Aerospace Engineering Theses & Dissertations

A novel concept proposed is the use of Shape Memory Alloy (SMA) to reduce the panel thermal deflection and flutter responses. SMA has unique ability to recover large prestrains completely when the alloy is heated (by aerodynamic heating in the present case) above the austenite start temperature A_s. During the recovery process, a large tensile recovery stress occurs if the SMA is restrained.

In this thesis, a panel subject to the combined aerodynamic and thermal loading is investigated. A nonlinear finite element model based on von Karman strain displacement relation is utilized to study the effectiveness of SMA …

Finite Element Analysis Of Nonlinear Panel Flutter Of Rectangular Composite Plates Under A Uniform Thermal Load, Lain Ross Dixon

Mechanical & Aerospace Engineering Theses & Dissertations

A finite element formulation is developed to analyze large-amplitude panel flutter of arbitrarily laminated composite plates subjected to a uniform temperature change. The plates considered are anisotropic composite, thin rectangular panels. The aerodynamic pressure load is modeled through the use of the first-order piston theory. The equations of motion for the oscillating plate are determined from the principle of virtual work. Two different solution procedures are given to determine the panel motions. The first procedure, which considers only the aerodynamic load, solves the panel limit-cycle motions by employing the linearized updated-mode with a nonlinear time function (LUM/NTF) approximation. The second …

An Experimental And Analytical Investigation Of Wing Flutter On A Trial Rotor V/Stol Aircraft, David L. Soistmann

Mechanical & Aerospace Engineering Theses & Dissertations

A wind tunnel model based on a trail rotor vehicle concept was tested for wing flutter in the subsonic flow regime. The wind tunnel model was flutter tested in the forward flight mode only. From this test it was determined that this conceptual vehicle may be susceptible to wing flutter. However, the flutter encountered was not catastrophic but was of the limited amplitude type. The trailing rotor blades were found to have a positive aerodynamic damping effect on flutter. The flutter mechanism for each flutter point was due to a coupling of the first wing bending and first wing torsion …