Aerodynamics and Fluid Mechanics Commons^™

Investigation Of The Impact Of The Shape Of The Wings On Formula E Racing Car Performance: Enhancements For Optimal Aerodynamics, Ednie Marthe Adlaikah Jozil

Honors Undergraduate Theses

The aerodynamic performance of a Formula E chassis significantly dictates its overall race efficiency, directly impacting crucial parameters such as battery range and thermal management. This thesis investigates the external aerodynamics of the baseline Gen 2 Formula E car and evaluates the performance gains of two novel aerodynamic packages: a "Fully Modified" configuration and a "Flat Rear Wing" design. Computational Fluid Dynamics (CFD) simulations were conducted to analyze drag coefficients (Cd), downforce generation, and vehicle wake structures at race-relevant free-stream velocities (e.g., 37 m/s and 89 m/s). To ensure numerical robustness, the computational setup was validated using a smooth sphere …

Aerodynamic Design And Analysis Of A Modified 2006 Mazda Miata, William N. Recher

Honors College Theses

Aerodynamic forces developed by automobiles have destabilizing effects at high speed. These forces tend to skew toward a vehicle’s rear which can present safety concerns, especially for rear-wheel-drive automobiles like the Mazda Miata. To address oversteer and high-speed instability, a vehicle’s design can be tailored to bring about aerodynamic balance and improve traction. LiDAR was used to bring the physical automobile into the digital space. Then, a splitter and diffuser were added to reduce the magnitude of the destabilizing forces. Next, the size and shape of the rear-wing required to balance the vehicle was calculated using a combination of parameters …

Dynamics Of Separated Flows In Diffusers With Vortex Generators, Sandeep Eldho James

Mechanical and Aerospace Engineering Dissertations - Archive

Flow through curved diffusers is complicated due to the possibility of flow separation and secondary flows. Vortex generators (VGs) are a class of passive flow separation control devices used to improve the flow quality in curved diffusers by suppressing flow separation. However, the literature review demands an in-depth investigation on the physical mechanisms related to flow separation control. Thus, this study aims to improve the understanding of the underlying flow physics associated with VG-induced flow separation control in confined flows. The chosen geometry for this study is a well-documented asymmetric diffuser which exhibits a mild flow separation.

The theoretical formulation …

Husker Motorsports Active Drag Reduction System, Creighton Hughes, Evan Killian, Micah Busboom, Aj Johnson, Jude Steffen

Honors Program: Senior Projects (Public)

Formula SAE is a multifaceted competition that involves student teams designing and competing with an open-wheel style race car. There are 5 different dynamic events included in the competition. Each event requires a unique aerodynamic setup to have the best performance possible. This design project focuses on a drag reduction system (DRS) that will improve aerodynamic performance, resulting in faster lap times and increased competitiveness. Key features include a direct electronic actuation mechanism that will allow the rear wing to be adjusted during a race. The benefits of the DRS system, include increased speed, improved handling, and greater fuel efficiency …

Design And Validation Of An Aerodynamic System For A Formula Sae® Vehicle Using Vehicle Dynamic Simulation And Experimentation, Evan S. Cole

Graduate Theses, Dissertations, and Problem Reports (ETD)

This thesis presents the design, simulation, and experimental validation for the aerodynamic system for a Formula SAE® vehicle. The Society of Automotive Engineers ® (SAE) hosts a collegiate competition annually called Formula SAE® where students design, fabricate, and test a small “formula style” vehicle. The vehicle performs in relatively slow maneuvers, around different courses and tests to evaluate the vehicle’s overall performance. Over the years, collegiate teams have put significant research into the design and manufacturing of the aerodynamics of these vehicles. In order to justify this undertaking for future teams at West Virginia University’s Formula SAE® program, a comprehensive …

Design And Manufacture Of An Aerodynamic Body That Meets Scaling Law Requirements And Survives Severe G-Load Environment For Free-Flight Testing, Anthony R. Gonzalez

Graduate Theses, Dissertations, and Problem Reports (ETD)

Design and Manufacture of an Aerodynamic Body that Meets Scaling Law Requirements and Survives Severe G-load Environment for Free-Flight Testing

Anthony Gonzalez

Developing scale models to test functionality and ascertain aerodynamic properties is critical before manufacturing full-size products. Through dimensional analysis and similitude, engineers create scale models to test any parameter of interest. This research aims to design a scale model of an aerodynamic body for repeated free-flight testing. The Froude number is the dominant scale model law used to determine the geometric, mass, and inertia scaling laws. A critical requirement for this research is that the model should be …

Assessment Of Conventional And Air-Jet Wheel Deflectors For Drag Reduction Of The Drivaer Model, Sandra K. S. Boetcher, Kaloki L. Nabutola

Publications

Aerodynamic drag is a large resistance force to vehicle motion, particularly at highway speeds. Conventional wheel deflectors were designed to reduce the wheel drag and, consequently, the overall vehicle drag; however, they may actually be detrimental to vehicle aerodynamics in modern designs. In the present study, computational fluid dynamics simulations were conducted on the notchback DrivAer model—a simplified, yet realistic, open-source vehicle model that incorporates features of a modern passenger vehicle. Conventional and air-jet wheel deflectors upstream of the front wheels were introduced to assess the effect of underbody-flow deflection on the vehicle drag. Conventional wheel-deflector designs with varying heights …

Active Control Of Coherent Structures In An Axisymmetric Jet, Michael Marques Goncalves

Doctoral Dissertations and Master's Theses

The primary objective of this work is to develop high-fidelity simulation model for jet noise control predictions and quantify the sound reduction when an external source frequency mode excitation is imposed on the jet flow. Whereas passive approaches using mixing devices, such as chevrons, have been shown to reduce low-frequency noise in jet engines, such approaches incur a performance penalty since they result in a reduced thrust. To avoid a performance penalty in reducing jet noise, the current work investigates a open-loop active noise control (ANC) system that utilizes a unsteady microjet actuator on the nozzle lip in the downstream …

Road Racing Aerodynamic Simulation + Testing, Jack Sawyer

Williams Honors College, Honors Research Projects

There are multiple goals for this project. The first goal of this project is to design, assemble and simulate additional aerodynamic components. Another goal is to create a product that can analyze various angles of attack of Aerodynamic components. The product will be used on, or off the track to determine the lift coefficients of vehicles at varying speeds. I will be using my 1992 Honda Civic for testing and compare my physical results to my simulated tests.

The project did come with a list of design and manufacturing challenges along with additional finical cost which has resulted in some …

Active Drag Reduction Of Ground Vehicles Using Air-Jet Wheel Deflectors, Kaloki Nabutola

Doctoral Dissertations and Master's Theses

Seven turbulence models were used to simulate the flow within the wheelhouse of a simplified vehicle body. The performance of each model was evaluated by comparing the aerodynamic coefficients obtained using computational fluid dynamics (CFD) to data collected from wind tunnel experiments. The performance of large eddy simulation (LES) and detached eddy simulation (DES) was largely dependent on the time step and grid size to accurately resolve turbulent eddies. The standard k-e, realizable k-e, k-w, DES, and LES all trended towards a drag coefficient which was 20% lower than the experimental value. In all numerical cases, the lift coefficient was …

A Cfd Study Investigating Drag Reduction For Different Offset And Inline Distance For Two Trucks Platooning, Wael Mokhtar, Kyle Dinger, Shardul Kachare, Mdrazib Hossain, Colin Britcher

Mechanical & Aerospace Engineering Faculty Publications

The automotive industry invests huge resources to improve fuel consumption of commercial vehicles by improving their aerodynamic efficiency. Recently, numerous studies investigating the effect of platooning on aerodynamic drag of semi-trucks have been performed by researchers indicating a positive impact. For the present study, a three-dimensional computational study was performed to investigate the effect of varying offset and linear distance during platooning on the total drag of two semi-trucks. The study was conducted on a full-scale model using Reynold’s Averaged Navier-Strokes governing equations for a moving ground simulation using the STAR-CCM+ computational package. Furthermore, for turbulence, the standard k- …

Autonomous Watercraft Simulation And Programming, Nicholas J. Savino

Student Scholar Showcase

Automation of various modes of transportation is thought to make travel more safe and efficient. Over the past several decades, advances to semi-autonomous and autonomous vehicles have led to advanced autopilot systems on planes and boats, and an increasing popularity of self-driving cars. We predicted the motion of an autonomous vehicle using simulations in Python. The simulation models the motion of a small scale watercraft, which can then be built and programmed using an Arduino Microcontroller. We examined different control methods for a simulated rescue craft to reach a target. We also examined the effects of different factors, such as …

Inkjet Printing: Facing Challenges And Its New Applications In Coating Industry, Sadegh Poozesh

Theses and Dissertations--Mechanical and Aerospace Engineering

This study is devoted to some of the most important issues for advancing inkjet printing for possible application in the coating industry with a focus on piezoelectric droplet on demand (DOD) inkjet technology. Current problems, as embodied in liquid filament breakup along with satellite droplet formation and reduction in droplet sizes, are discussed and then potential solutions identified. For satellite droplets, it is shown that liquid filament break-up behavior can be predicted by using a combination of two pi-numbers, including the Weber number, We and the Ohnesorge number, Oh, or the Reynolds number, Re, and the Weber number, …

Use Of A Rolling Road System In Crosswind Conditions, Mau-Kuo Chen

Mechanical & Aerospace Engineering Theses & Dissertations

Wind tunnel testing continues to play an important role in vehicle aerodynamic development. Accurate results are strongly associated with whether the wind tunnel can closely simulate the on-road conditions, including the Reynolds number and all boundary conditions. Rolling road systems (or moving belts) have been a successful tool for many auto makers and racing teams to simulate the relative motion between the stationary vehicle model and the floor in the test section. The mechanism of the rolling road system is simple, but how it affects the adjacent flow field and how this flow interacts with the flow underneath the vehicle …

Drag Reduction Of A Modern Straight Truck, Drew Landman, Matthew Cragun, Mike Mccormick, Richard Wood

Mechanical & Aerospace Engineering Faculty Publications

A wind tunnel test program was conducted at the Langley Full Scale Tunnel (LFST) to evaluate the performance of five passive drag reduction configurations on a modern straight truck at full scale. Configurations were tested in a build-up fashion with results representing a cumulative effect. Tested configurations include a front valance, a front box fairing, a boat-tail, an ideal side-skirt, and a practical side-skirt. Configurations were evaluated over a nominal 9 degree yaw sweep to establish wind averaged drag coefficients using SAE J1252. Genuine replicate yaw sweeps were used in an uncertainty analysis. Results show up to 28% improvement in …

Understanding Practical Limits To Heavy Truck Drag Reduction, Drew Landman, Richard Wood, Whitney Seay, John Bledsoe

Mechanical & Aerospace Engineering Faculty Publications

A heavy truck wind tunnel test program is currently underway at the Langley Full Scale Tunnel (LFST). Seven passive drag reducing device configurations have been evaluated on a heavy truck model with the objective of understanding the practical limits to drag reduction achievable on a modern tractor trailer through add-on devices. The configurations tested include side skirts of varying length, a full gap seal, and tapered rear panels. All configurations were evaluated over a nominal 15 degree yaw sweep to establish wind averaged drag coefficients over a broad speed range using SAE J1252. The tests were conducted by first quantifying …

External Aerodynamics Of Heavy Ground Vehicles: Computations And Wind Tunnel Testing, Ilhan Bayraktar

Mechanical & Aerospace Engineering Theses & Dissertations

Aerodynamic characteristics of a ground vehicle affect vehicle operation in many ways. Aerodynamic drag, lift and side forces have influence on fuel efficiency, vehicle top speed and acceleration performance. In addition, engine cooling, air conditioning, wind noise, visibility, stability and crosswind sensitivity are some other tasks for vehicle aerodynamics. All of these areas benefit from drag reduction and changing the lift force in favor of the operating conditions. This can be achieved by optimization of external body geometry and flow modification devices. Considering the latter, a thorough understanding of the airflow is a prerequisite.

The present study aims to simulate …

Computational Fluid Dynamic Study Of A Nascar Winston Cup Series Race Car, Terry L. Meek Jr.

Mechanical & Aerospace Engineering Theses & Dissertations

Since the goal of NASCAR racing is to win and since drag is a force the vehicle must overcome, a thorough understanding of the drag generating airflow around and through the automobile is greatly desired. The external airflow contributes to most of the drag that a car experiences and most of the downforce the vehicle produces. Therefore, an estimate of the vehicle's performance may be evaluated using a computational aerodynamics model. This thesis presents a computational fluid dynamic (CFD) analysis of a NASCAR Winston Cup series race car to investigate the salient flow characteristics.

Before a computational analysis could be …

A Feasibility Study Of Fuel Cell Cogeneration In Industry, Scott B. Phelps, J. Kelly Kissock

Mechanical and Aerospace Engineering Faculty Publications

Up until now, most of the literature on fuel cell cogeneration describes cogeneration at commercial sites. In this study, a PC25C phosphoric acid fuel cell cogeneration system was designed for an industrial facility and an economic analysis was performed. The US DOE Industrial Assessment Center (IAC) database was examined to determine what industry considers a good investment for energy saving measures. Finally, the results of the cogeneration analysis and database investigation were used to project the conditions in which the PC25C might be accepted by industry.

Analysis of IAC database revealed that energy conservation recommendations with simple paybacks as high …