Open Access. Powered by Scholars. Published by Universities.®

Systems Science Commons

Open Access. Powered by Scholars. Published by Universities.®

4,159 Full-Text Articles 10,346 Authors 1,985,298 Downloads 67 Institutions

All Articles in Systems Science

Faceted Search

4,159 full-text articles. Page 202 of 206.

Smooth Transition Method Over Entire Speed Range Of Switched Reluctance Motor, Diansheng Sun 2019 1.Aviation Special Motor and Control Research Center, Binzhou University, Binzhou 256600, china; ;2.College of Electrical Engineering, Binzhou University, Binzhou 256600, china;

Smooth Transition Method Over Entire Speed Range Of Switched Reluctance Motor, Diansheng Sun

Journal of System Simulation

Abstract: In order to smoothly switch different control modes of switched reluctance motor under the condition of low speed and high speed, a novel scheme using function fitting method to control turn-on angle, turn-off angle and phase current chopping is proposed. The active disturbance rejection speed control system is structured for switched reluctance motor in order to restrain all kinds of disturbance and improve the dynamic performance. Simulation results indicate that the principle of the method is correct and the turn-on angle, turn-off angle and phase current chopping is coordinated to realize the smooth switching of different control modes with …


A Novel Algorithm For Improving Fairness Between Uplink And Downlink Flows In Heterogeneous Network, Peiyu Li, Zheqing Li, Wang Hui, Xia Qian 2019 1.Network Information Center of Henan University of Science and Technology, Luoyang 471023, China; ;

A Novel Algorithm For Improving Fairness Between Uplink And Downlink Flows In Heterogeneous Network, Peiyu Li, Zheqing Li, Wang Hui, Xia Qian

Journal of System Simulation

Abstract: In order to improve the fairness between uplink and downlink flows in AP optimization, a novel algorithm called FOUD(fairness over uplink and downlink) is proposed.Considering the influence of the attempt limit and the bit error rate of wireless, the FOUD algorithm modeling of AP and wireless stations is studied separately by using two-dimensional Markov chain, which derives the probability of data sending under the condition of different bit error rate and different number of uplink and downlink flows. Simulation results show that FOUD can improve the fairness of the uplink and downlink bandwidth as well as the …


Frequency Domain Analysis Of Common Configuration Semi-Submersible Drilling Platform Based On System Simulation, Chen Bo, Zhiyong Yu, Lü Yong, Xiaojian Li 2019 School of Mechanical and Electrical Engineering, Lanzhou University of Technology, Lanzhou 730050, China;

Frequency Domain Analysis Of Common Configuration Semi-Submersible Drilling Platform Based On System Simulation, Chen Bo, Zhiyong Yu, Lü Yong, Xiaojian Li

Journal of System Simulation

Abstract: To analysis of 4 semi-submersible drilling platform hydrodynamic performance providing a comprehensive guidance for system selection. The 1:1 3D wet surface model is established by ANSYS and numerical simulation is carried out based on the dynamic analysis software AQWA. Simulation results show that longitudinal waves impact the surge, heaving and pitching motion a lot, beam seas have large effects on the sway, heave, roll motion vertical heave response increases significantly, as will as surge, sway, heave damping coefficient of vector direction and the added mass coefficient of algebraic. We can not only increase the number of columns to …


Structure Optimization Analysis Of Multi-Span Antisymmetric Arch Tower Cable-Stayed Bridge, Xijun Liu, Yuan Bo, Tianyi Liu 2019 School of Mechanical Engineering, Tianjin University, Tianjin 300354, China;

Structure Optimization Analysis Of Multi-Span Antisymmetric Arch Tower Cable-Stayed Bridge, Xijun Liu, Yuan Bo, Tianyi Liu

Journal of System Simulation

Abstract: In order to analyze its force under different sections and arch span ratio of the Antisymmetric arch tower cable-stayed bridge, the paper takes an anti-symmetric arch tower cable-stayed bridge as an engineering example. Considering the effect of dead load and temperature, finite software is used to calculate the stress of the arch tower and deflection of the deck and its corresponding dynamic characteristics under different types of arch sections and different rise-span ratio of the arch. The results show that the circular cross-section has better mechanical performance compared with other types of arches tower section with the same …


Fuzzy Sliding Backstepping Mode Control For Flight Simulator Servo Based On Friction And Disturbance Compensation, Huibo Liu, Shanglei Liu 2019 School of Information Engineering, Inner Mongolia University of Science and Technology, Baotou 014010, China;

Fuzzy Sliding Backstepping Mode Control For Flight Simulator Servo Based On Friction And Disturbance Compensation, Huibo Liu, Shanglei Liu

Journal of System Simulation

Abstract: Considering friction, modeling errors and other uncertainties of flight simulator servo system, a compensation strategy which combines model-based friction compensation with nonlinear disturbance observer compensation was proposed. First, the friction is modeled , whose parameters are identified by using genetic algorithm, and using the identified model to compensate. Second, using a nonlinear disturbance observer to estimate the modeling errors, friction less-compensation or over-compensation and other uncertainties, and using this observed value to compensate. The system adopted sliding backstepping controller to ensure the stabilization of the system. Finally, the fuzzy algorithm is adopted to adjust the switching gain of sliding …


Interval Fuzzy Modeling Based On Minimizing-Norm On Approximation Error, Xiaoyong Liu, Zhonggang Xiong, Changguo Yan 2019 College of engineering and technology, Zunyi Normal College, Zunyi 563002, China;

Interval Fuzzy Modeling Based On Minimizing-Norm On Approximation Error, Xiaoyong Liu, Zhonggang Xiong, Changguo Yan

Journal of System Simulation

Abstract: As the obtained data in many practical applications tend to be uncertain or inaccurate, conventional modeling methods characterized by deterministic model for this type of data have become undesirable. Taking linear programming and TS fuzzy model and some ideas from norm minimization into consideration, a novel method identifying interval fuzzy model (INFUMO) consisting of upper and lower TS fuzzy model (referred to as fU and fL) has been studied. In order to solve INFUMO, optimization problems based on minimizing-norm with respect to approximation error corresponding to fU and fL are constructed. Finally, optimization problems …


Preliminary Study Of Modeling And Simulation Technology Oriented To Neo-Type Artificial Intelligent Systems, LiBo Hu, Xudong Chai, Zhang Lin, Li Tan, Duzheng Qing, Tingyu Lin, Liu Yang 2019 1.State Key Laboratory of Intelligent Manufacturing System Technology, Beijing Institute of Electronic System Engineering, Beijing 100854, China; ;2.Beihang University, Engineering Research Center of Complex Product Advanced Manufacturing Systems, Ministry of Education, Beijing 100191, China; ;

Preliminary Study Of Modeling And Simulation Technology Oriented To Neo-Type Artificial Intelligent Systems, Libo Hu, Xudong Chai, Zhang Lin, Li Tan, Duzheng Qing, Tingyu Lin, Liu Yang

Journal of System Simulation

Abstract: A brief interpretation of the rapidly developing “New Internet+ Big Data+ Artificial Intelligence+” era is given in the paperand the essence and the architectureof neo-type artificial intelligence systems are explained. The meaning of neo-type artificial intelligence system oriented modelling and simulation technology is proposed and the new challenges they are facing are discussed. The research contents and preliminaryresults on neo-type artificial intelligence system oriented modelling and simulation technology are given, which includeneo-type artificial intelligence system oriented modelling/secondary modelling, intelligent simulation computer, smart cloud simulation and intelligent simulation hardware/software supporting system technology, and intelligent simulation system application engineering technology. Several …


Prediction Model Of Particle Size Distribution In Bauxite Continuous Ball Milling Process, Tianyu Ma, Yalin Wang, Kun Shen, Jinping Liu 2019 1.College of Physics and Information Science, Hunan Normal University, Changsha 410006, China; ;

Prediction Model Of Particle Size Distribution In Bauxite Continuous Ball Milling Process, Tianyu Ma, Yalin Wang, Kun Shen, Jinping Liu

Journal of System Simulation

Abstract: As it is difficult to detect the particle size distribution of ball milling process on line, a prediction model of particle size distribution in bauxite continuous ball-milling process is proposed, which is based on data-driven method and population balance model (PBM) frame. The break-rate model structure of PBM is improved according to the characteristic data of batch grinding test of bauxite. The residual time distribution density function is improved by considering the characteristics of residence time distribution for different particle sizes. The key parameters of the model are optimized by the data of batch-test and continuous ball-milling process using …


A Method Of 3d Scattering Center Extraction Based On Multiple Hrrp Series, Cui Shan, Li Sheng, Yan Hua 2019 Science and Technology on Electromagnetic Scattering Laboratory, Beijing 100854, China;

A Method Of 3d Scattering Center Extraction Based On Multiple Hrrp Series, Cui Shan, Li Sheng, Yan Hua

Journal of System Simulation

Abstract: Scattering center extraction is the key content in the research of radar target characteristics, particularly the sliding type of scattering center. An extraction method based on the parametric scattering center model is proposed, which takes advantage of Hough transformation to extract geometric location and sliding radius parameters. The distance is gotten in the line of radar sight, and the useful information is obtained from high-resolution range profile (HRRP) series, which estimates size parameter of scattering centers and accomplishes signal reconstruction. This method solves the problems of point and sliding scattering center extraction. Simulation example manifests the applicability of the …


Modeling And Simulation Of The Crosstalk On Aircraft Arinc429 Data Bus, Xudong Shi, Ruowen Wang, Jialin Wang, Hongxu Zhao 2019 1.Aviation Ground Special Equipments Research Base, Civil Aviation University of China, Tianjin 300300, China; ;2.College of Electronic Information and Automation, Civil Aviation University of China, Tianjin 300300, China;

Modeling And Simulation Of The Crosstalk On Aircraft Arinc429 Data Bus, Xudong Shi, Ruowen Wang, Jialin Wang, Hongxu Zhao

Journal of System Simulation

Abstract: Based on the theory of multi-conductor transmission line, the crosstalk between a single cable and a UTP (unshielded twisted pairs) cable was studied. The MATLAB and CST were employed to do the theoretical calculation and modeling respectively, and the comparison result proved the validity and accuracy of the proposed model. Based on the UTP model, the shielding layer was used to build the STP(shielded twisted-wire pairs) model according to the ARINC429 specification, and the crosstalk which caused by a large voltage transient happening on the adjacent power line on the aircraft was further analyzed. The distance and length of …


Simulation Of Stone Cutting Process Based On Adaptive Coupling Method, Yongjun Tian, Guolin Duan, Junguang Kang, Jianhua Gang 2019 1.School of Mechanical Engineering, Hebei University of Technology, Tianjin 300130, China; ;2.Tianjin University of Technology and Education,Engineering Training Center, Tianjin 300222, China;

Simulation Of Stone Cutting Process Based On Adaptive Coupling Method, Yongjun Tian, Guolin Duan, Junguang Kang, Jianhua Gang

Journal of System Simulation

Abstract: Aiming at complex nonlinear dynamic behaviors of stone-cutting process with circular saw and handling large mesh deformation instability in FEM, according to brittle material fracture mechanism, an adaptive coupling algorithm was established for calculating the cutting process of circular saw-stone materials system. The results show that the material removal process is a process of intermittent cycle; the cutting force is zero at the beginning of the process, and the force increases rapidly when the blade contacts with the stone, then decreases, eventually varies in a stable fluctuation. According to von-Mises stress distributions of saw blade and stone, the easily …


Fault Diagnosis System Of Lithium Battery Based On Petri Net, Diju Gao, Lan Xi, Aidi Shen 2019 Key Laboratory Marine Technology & Control Engineering Ministry Communications, Shanghai Maritime University, Shanghai 201306, China;

Fault Diagnosis System Of Lithium Battery Based On Petri Net, Diju Gao, Lan Xi, Aidi Shen

Journal of System Simulation

Abstract: To improve the efficiency of lithium battery fault diagnosis system, a fault diagnosis system based on Petri net is proposed. The fault diagnosis model based on Petri net came from the analysis of the inconsistent voltages between single cell in lithium batteries during charge and discharge. The system can find the fault causes according to abnormal signals detected by sensor. The control logic diagram of the fault diagnosis model is established by state flow, and simulated by simulink. The results of model verification and simulation show that the cause for inconsistent voltage is distinguished meticulously by the fault diagnosis …


Research And Simulation For Military Contests Based On Ahp And Entropy Models, Rusheng Ju, Zhengqiu Zhu, Yunxiu Zeng, Ruixian Wang, Xiaogang Qiu 2019 Institute of Systems Engineering National University of Defense Technology, Changsha 410073, China;

Research And Simulation For Military Contests Based On Ahp And Entropy Models, Rusheng Ju, Zhengqiu Zhu, Yunxiu Zeng, Ruixian Wang, Xiaogang Qiu

Journal of System Simulation

Abstract: The paper studiesthe comprehensive military contests which are held frequently among military universities. Different from the qualitative analysis methods before, an analytic hierarchy process model is set up to analyze the effects which training programs have on students. A great amount of data is put into the entropy model to analyze the rationality of AHP model. This paper also sets the effect value as the input data of the emulating model to simulate the whole exercise process before contests which can verify the results received from AHP and entropy models. Research findings are helpful for superior leaders to make …


Disturbance Rejection Based Robust Control Approach For Servo System With Backlash, Chongwei Han, Peng Chao, Zhixiang Shi, Li Zhong 2019 1.Northwest Institute of Mechanical & Electrical Engineering, Xianyang 712099, China; ;

Disturbance Rejection Based Robust Control Approach For Servo System With Backlash, Chongwei Han, Peng Chao, Zhixiang Shi, Li Zhong

Journal of System Simulation

Abstract: With the rapid development of industry and science technology, the control performance requirements for servo system become higher and higher. Aiming at the servo system with backlash, a disturbance rejection based robust control approach is studied, which sees the backlash as external disturbance. It utilizes a disturbance rejection compensator to reduce the adverse effects caused by backlash, a mixed sensitivity based robust feedback controller to enhance the tracking control precision and robustness. The model of the servo system with backlash is built based on the analysis of system structure and work principle. The control principle, the robust disturbance rejection …


Research On Wind Turbine Test System Based On Jointsimulation, Zhongyue Song, Zhen Dong, Zhang Hao, Zhanqun Shi, Jiaojiao Ma 2019 School of Mechanical Engineering, Hebei University of Technology,Tianjin 300130, China;

Research On Wind Turbine Test System Based On Jointsimulation, Zhongyue Song, Zhen Dong, Zhang Hao, Zhanqun Shi, Jiaojiao Ma

Journal of System Simulation

Abstract: As the test equipment of wind turbine can not simulate wind driven exactly and the impact of environmental factors is hard to be taken into account, the simulation results have larger errors. The problem is solved by establishing the virtual test bench in the way of combined simulation. The wind speed modelis optimized by combining the fitting of probability and the combinated wind speed model to drive the wind turbine;and the settings of some relevant contact force parameters are considered,which canmake the simulation results are closer to the actual situation. The credibilityof the system isdemonstrated and the validity …


Uav Attitude Control With Lqr Controller Based On Extended State Observer, Pan Jian, Changlong Liu 2019 Department of Electrical and Electronic Engineering, Hubei University of Technology, Wuhan 430068, China;

Uav Attitude Control With Lqr Controller Based On Extended State Observer, Pan Jian, Changlong Liu

Journal of System Simulation

Abstract: Due to the external disturbances and parameter variations in the complex environment, the traditional linear quadratic controller (LQR) may induce instability to the controlled object. A control strategy of LQR based on extended state observer (ESO) is proposed, which aims to ensure the working reliability of the controlled object in complex environment. The nonlinear mathematical model of the quadrotor Qball-X4 is established. The ESO’s abilities of estimating and compensating the impact of internal/external disturbances simultaneously are used to improve the LQR attitude controller. Matlab/Simulink simulation and an experiment of trajectory tracking on the quadrotor Qball-X4 verify the validity …


Development Of A New Instrument To Assess The Performance Of Systems Engineers, Niamat Ullah Ibne Hossain, Morteza Nagahi, Raed Jaradat, Charles Keating 2019 Mississippi State University

Development Of A New Instrument To Assess The Performance Of Systems Engineers, Niamat Ullah Ibne Hossain, Morteza Nagahi, Raed Jaradat, Charles Keating

Engineering Management & Systems Engineering Faculty Publications

Complex systems continue to confound the capabilities of systems engineers to deal with and navigate a new generation of problems. Thus, there is an emerging need to develop a cadre of effective systems engineers capable of efficiently addressing complex systems problems. This paper introduces a new system engineering instrument that assesses the performance of systems engineers. The instrument is based on the set of performance indicators examining six fundamental system engineering attributes. This instrument would provide a baseline to understand the current state of the systems engineering skills for a systems engineer and indicate developmental areas to enhance those skills. …


Combination Forecasting Of Stock Index Time Series Based On Cooperative Game Theory, Luo Wei 2018 Hunan Railway Professional Technology College, Zhuzhou 412001, China;

Combination Forecasting Of Stock Index Time Series Based On Cooperative Game Theory, Luo Wei

Journal of System Simulation

Abstract: In view of the characteristics of nonlinear, large amplitude, frequent fluctuations in China's stock market, a prediction method of intelligent composite stock index time series based on the cooperative game is presented. The prediction model of stock index time series is established by using neural network method based on the correlations among the various economic indicators, and the development trend and laws of stock index time series are established by using the improved ARIMA method. The two methods are combined by importing cooperative game method. Simulation results show that the prediction accuracy of the presented method is controlled …


Real-Time Simulator For Spatial Information Networks Based On Analog If Signal Processing, Zeguo Yang, Ma Shang, Diaopeng Huang, Jianhao Hu, Lixiang Liu 2018 1. National Key Laboratory of Science and Technology on Communication, Chengdu, 611731, China;;

Real-Time Simulator For Spatial Information Networks Based On Analog If Signal Processing, Zeguo Yang, Ma Shang, Diaopeng Huang, Jianhao Hu, Lixiang Liu

Journal of System Simulation

Abstract: To solve the problem of real-time simulation of spatial information network with high dynamic network topology, a real-time simulator based on the IF signal processing is proposed. Compared with traditional channel simulator, it supports both the channel transmission characteristics like channel fading, Doppler shift, noise, and path delay, and the real-time simulation of dynamic network topology changes. The simulator supports 8~128 70 MHz IF (0~20 MHz signal bandwidth) emulated nodes with flexible link type configuration. The maximal fading depth is 100 dB, the maximal Doppler shift is 2 MHz, and the maximal path delay can reach up …


Research And Simulation Of Roots-Type Power Machine Control System Based On Fuzzy Pid, Yan-jun Xiao, Yonggeng Wang, Jing Ran, Feng Hua, Yongcong Li 2018 School of Mechanical Engineering, Hebei University of Technology, Tianjin 300130, China;

Research And Simulation Of Roots-Type Power Machine Control System Based On Fuzzy Pid, Yan-Jun Xiao, Yonggeng Wang, Jing Ran, Feng Hua, Yongcong Li

Journal of System Simulation

Abstract: For utilizing the domestic low grade waste heat resources, a Roots-type steam engine is developed. To make the roots engine stably output electric energy, an efficient constant power control system needs to be designed. The controlled object characteristics of the roots engine are analyzed; the modeling of the control system is established; and on this basis the fuzzy control algorithm is introduced. The fuzzy adaptive PID controller for the roots power machine constant power output is designed and the related MATLAB simulation is carried out. The results show that the Roots type steam power machine with fuzzy adaptive PID …


Digital Commons powered by bepress