Geological Engineering Commons^™

Overall Psd And Fractal Characteristics Of Tight Oil Reservoirs: A Case Study Of Lucaogou Formation In Junggar Basin, China, Xixin Wang, Jiagen Hou, Yuming Liu, Peiqiang Zhao, Ke Ma, Dongmei Wang, Xiaoxu Ren, Lin Yan

Geology and Geological Engineering Faculty Publications

Lucaogou tight oil reservoir, located in the Junggar Basin, Northwest of China, is one of the typical tight oil reservoirs. Complex lithology leads to a wide pore size distribution (PSD), ranging from several nanometers to hundreds of micrometers. To better understand PSD and fractal features of Lucaogou tight oil reservoir, the experiment methods including scanning electron microscope (SEM), rate-controlled mercury injection (RMI) and pressure-controlled mercury injection (PMI) were performed on the six samples with different lithology. The results indicate that four types of pores exist in Lucaogou tight oil reservoir, including dissolution pores, clay dominated pores, microfractures and inter-granular pores. …

Landsliding Near Enguri Dam (Caucasus, Georgia) And Possible Seismoectonic Effects, Alessandro Tibaldi, Paolo Oppizzi, John S. Gierke, Thomas Oommen, Nino Tsereteli, Davit Odilavadze

Michigan Tech Publications, Part 1

The Enguri dam and water reservoir, nested in southwestern Caucasus (Republic of Georgia), are surrounded by steep mountain slopes. At a distance of 2.5 km from the dam, a mountain ridge along the reservoir is affected by active deformations with a double vergence. The western slope, directly facing the reservoir, has deformations that involve a subaerial area of 1.2 km2. The head scarp interests the main Jvari-Khaishi-Mestia road with offset of man-made features that indicate slip rates of 2-9 cm/y. Static, pseudostatic and Newmark numerical analyses, based on field and seismological data, suggest different unstable rock volumes basing on the …

Slalom: An All-Surface Snow Water Path Retrieval Algorithm For The Gpm Microwave Imager, Jean-François Rysman, Giulia Panegrossi, Paolo Sanò, Anna Cinzia Marra, Stefano Dietrich, Lisa Milani, Mark S. Kulie

Michigan Tech Publications, Part 1

This paper describes a new algorithm that is able to detect snowfall and retrieve the associated snow water path (SWP), for any surface type, using the Global Precipitation Measurement (GPM) Microwave Imager (GMI). The algorithm is tuned and evaluated against coincident observations of the Cloud Profiling Radar (CPR) onboard CloudSat. It is composed of three modules for (i) snowfall detection, (ii) supercooled droplet detection and (iii) SWP retrieval. This algorithm takes into account environmental conditions to retrieve SWP and does not rely on any surface classification scheme. The snowfall detection module is able to detect 83% of snowfall events including …

Spatial And Temporal Storm Generation From A Stochastic View, Jiaxiang Ding, Josept D. Revuelta-Acosta, Engel Bernard

The Summer Undergraduate Research Fellowship (SURF) Symposium

Precipitation is one of the most important parameters in the study of hydrology and most of the research has been done on daily storm generation. Current weather generation models are used to replicate daily or monthly time resolution, which is not able to show the variability within one day or one month. This project deals with sub-daily storm generation with finer resolution and more accurate estimation, which also requires an independent storm separation method. And the Monte Carlo correlated multivariate simulation is applied to compute the variables. The description is essential for soil erosion and water quality research. Another reason …

Demonstration Of The Gas Assisted Gravity Drainage (Gagd) Process In Carbonate Rocks., Alok Jiteshkumar Shah

LSU Master's Theses

The Gas Assisted Gravity Drainage (GAGD) process was developed and patented by Dr. Rao at LSU in the early 2000s. The process involves the use of several existing or new vertical injection wells to inject gas and use the natural segregation of reservoir fluids from the density difference and the gravitational forces to displace the trapped oil and mobilize the oil downwards to be produced by a horizontal producing well. The GAGD process can be implemented as a secondary or tertiary oil recovery method. Several physical model experiments have been conducted to demonstrate the effectiveness of the GAGD process for …

Sensitivity Of Atmospheric Aerosol Scavenging To Precipitation Intensity And Frequency In The Context Of Global Climate Change, Pei Hou, Shiliang Wu, Jessica L. Mccarty, Yang Gao

Michigan Tech Publications, Part 1

Wet deposition driven by precipitation is an important sink for atmospheric aerosols and soluble gases. We investigate the sensitivity of atmospheric aerosol lifetimes to precipitation intensity and frequency in the context of global climate change. Our sensitivity model simulations, through some simplified perturbations to precipitation in the GEOS-Chem model, show that the removal efficiency and hence the atmospheric lifetime of aerosols have significantly higher sensitivities to precipitation frequencies than to precipitation intensities, indicating that the same amount of precipitation may lead to different removal efficiencies of atmospheric aerosols. Combining the long-term trends of precipitation patterns for various regions with the …

The Effect Of Wellbore Circulation On Building An Lcm Bridge At The Fracture Aperture, Ghassan Alshubbar, Runar Nygaard, Montri Jeennakorn

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

Different laboratory experimental setups with slotted disks, simulating fractures' apertures, have been used extensively to formulate effective loss circulation materials (LCM) recipes. The amount of fluid loss and sealing pressure have been used as the evaluation criteria. The question still remains is how valuable these tests are when LCM fluids are circulated in the wellbore to stop losses. The main objective of this work is to study the effect of the annular fluid flow on building an LCM bridge at the fracture aperture. To address the objective, a fluid loss apparatus has been developed to mimic wellbore circulation. Tapered slotted …

The Ozone Monitoring Instrument: Overview Of 14 Years In Space, Pieternel F. Levelt, Joanna Joiner, Johanna Tamminen, J. Pepijn Veefkind, Pawan K. Bhartia, Simon Carn, Et. Al.

Michigan Tech Publications, Part 1

This overview paper highlights the successes of the Ozone Monitoring Instrument (OMI) on board the Aura satellite spanning a period of nearly 14 years. Data from OMI has been used in a wide range of applications and research resulting in many new findings. Due to its unprecedented spatial resolution, in combination with daily global coverage, OMI plays a unique role in measuring trace gases important for the ozone layer, air quality, and climate change. With the operational very fast delivery (VFD; direct readout) and near real-time (NRT) availability of the data, OMI also plays an important role in the development …

Hawai'i Wildlife Fund V. County Of Maui, Lowell J. Chandler

Public Land & Resources Law Review

In Hawai’i Wildlife Fund v. County of Maui, the Ninth Circuit held that the plain language of the Clean Water Act provides jurisdiction over indirect discharges of pollutants from a point source into groundwater that is shown to be connected to navigable waters. The court found that studies confirmed pollutants entering the Pacific Ocean were fairly traceable to the County of Maui’s sewage disposal wells. In affirming the district court’s ruling, the Ninth Circuit held that Maui County violated the Clean Water Act by discharging pollutants into a navigable water without the required permit. The court also concluded the …

Spectral Analysis Of Surface Waves To Detect Subsurface Voids, Payman Hajiani, Neil Lennart Anderson, J. David Rogers

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

Systems and methods for detecting a subsurface cavity. A source applies a force to ground under inspection and a plurality of sensors coupled to the ground detect resulting surface waves. A processor is configured to extract phase and frequency components of the acquired seismic data, identify a phase shift in surface waves in the ground under inspection based on the extracted phase and frequency components, and determine one or more physical characteristics of a subsurface cavity based on the identified phase shift

Mountain Front Recharge In A Semi-Arid Climate, Southwest Montana, Charles Shama

Graduate Theses & Non-Theses

Groundwater recharge to regional valley benches originates largely from adjacent Mountain Front Recharge (MFR). The Madison Valley in Southwest Montana is a semi-arid cold climate that receives 31.75cm annual valley precipitation. In this study, two drainages are characterized and compared, looking at the hydrological processes between the stream and groundwater. North Meadow Creek is a high elevation stream dominated by snowmelt and contains reaches of gaining and losing surface water to groundwater. Daylight Creek is a spring fed disconnected stream. Methods used a surface water balance, temperature as an environmental tracer and two and three component mixing models to investigate …

Characterization Of Peak Shear Strength Of Rough Rock Joints Using The Limited Displacement Multi-Stage Direct Shear (Ldmsd) Test Method, Michael Petro

Graduate Theses & Non-Theses

Current standardized direct shear test methods for rock joints do not account for damage caused to the individually unique asperity profiles of each sample. Current test methods require either a single sample to be sheared to large displacements under successive normal stresses, or the use of similar samples in multiple tests. Successive shearing of a single sample damages surface asperities and causes the overall roughness profile of the sample to change, reducing peak shear stress and consequently resulting in underestimation of friction angle and overestimation of joint shear intercept (cohesion). Obtaining joint surface specimens with identical roughness and geometry is …

Fluid Inclusion And Stable Isotope Investigation Of Hydrothermal Talc And Chlorite Deposits In Southwest Montana, Garrett Hill

Graduate Theses & Non-Theses

Talc and chlorite deposits of southwest Montana formed as hydrothermal replacements of Archean and/or early Proterozoic dolomitic marble and quartzo-feldspathic gneiss. Although the hydrothermal replacement model is generally accepted, less is known about the temperature, composition, and origin of the fluids involved in talc and chlorite formation. The present study examines fluid inclusions in quartz associated with both talc and chlorite, stable hydrogen and oxygen isotopes of talc, chlorite, and quartz, and stable carbon and oxygen isotopes of carbonate minerals. The deposits being examined include the Yellowstone, Beaverhead and Willow Creek talc mines, and the Antler chlorite mine.

Fluid inclusion …

Mineralogy And Sulfur Isotope Geochemistry Of The Apex And Bonanza Prospects At The Golden Sunlight Mine, Montana, Hamadou Gnanou

Graduate Theses & Non-Theses

The Golden Sunlight mine, located 50 km to the east of the famous Butte porphyry/lode deposits, is the largest gold mine in Montana, and has produced over 3 million ounces of gold in its 35+ year history. Most of this gold has come from the Mineral Hill breccia pipe (MHBP), a west dipping, cylindrical body of brecciated latite and country rock fragments of the Precambrian LaHood and Greyson Formations. The breccia pipe is late Cretaceous in age (84±18 Ma, DeWitt et al., 1986), is silicified, pyrite-rich, and is mineralized with gold, silver, and minor base metals. Because the MHBP has …

Uav-Based Geotechnical Modeling And Mapping Of An Inaccessible Underground Site, Elizabeth Anne Russell

Graduate Theses & Non-Theses

Digital photogrammetry is becoming a more common method used for mapping geological and structural rock mass features in underground mining. The issue of capturing geological and structural data in inaccessible, unsupported areas of mines remains even when utilizing terrestrial photogrammetric methods; thus, geotechnical models of mines are left with incomplete datasets. Large unsupported underground voids, like stopes, have the potential to cause major failures, but by filling in the geotechnical data gaps in inaccessible areas, potential failures can be predicted through kinematic analysis of the area’s mapped discontinuities. Implementation of Unmanned Aerial Vehicles (UAVs) in underground mines and recent advances …

Experimental Investigation Of And Constitutive Model For The Thermo-Poro-Mechanical Deformation Of Granular Salt Under Hydrostatic Compression, Brandon C. Lampe

Civil Engineering ETDs

The influence of pore pressure and porosity on the ductile deformation of granular salt was experimentally investigated under hydrostatic compression. Confining and pore pressures were independently controlled while granular salt samples exhibited rate-dependent deformation that resulted in large decreases of sample volume and porosity. The sample deformation rates were observed to correspond with both the sample porosity and the pressure difference between the confining and pore pressures. Post-test observations revealed that the reduced porosity was caused by the solid particles deforming in a ductile manner. Insight into the cause of ductile deformation was gained by considering the local stress distribution …

Bathymetry Data For Lakes Azuei And Enriquillo, Michael Piasecki, Mahrokh Moknatian

Publications and Research

This data set supports and forms the basis for the development of Digital Bathymetry Models (DBM) for Lakes Azuei (Haiti) and Enriquillo (Dominican Republic). Bathymetric Data is typically acquired using Sonar devices that measure the depth at specific points along a boat track and for which the longitude and latitude is recorded. From the resulting point cloud one develop a seamless representation of the floor of the lake on either a raster set (which is what we have done) or try to use a contour (vector representation) model in which the depth contours appear as polygons or -lines. The raw …

Vertical Stress And Stability Of Interburden Over An Abandoned Pillar Working Before Upward Mining: A Case Study, Jinwen Bai, Guorui Feng, Shanyong Wang, Tingye Qi, Jian Yang, Jun Guo, Zhen Li, Xianjie Du, Zehua Wang, Yunlou Du, Yujiang Zhang

Faculty & Staff Scholarship

Upward mining of the residual coal seam over an abandoned pillar working is one of the effective measures to alleviate the contradiction between limited resources and increased consumption. Interburden stability over an abandoned pillar working plays a significant role in guaranteeing the safety of upward mining; however, it has not yet been extensively studied and understood. In this study, the vertical stress of the interburden over an abandoned pillar working was first investigated. The mechanical model of the interburden was established and the damage conditions were analysed. Then, the stability of the interburden over 38502 abandoned workings in Baijiazhuang coal …

Toxicity Screening Of Biochar-Mineral Composites Using Germination Tests, Jan Mumme, Josephine Getz, Munoo Prasad, Ulf Lüder, Kern Jurgen, Ondrej Masek, Wolfram Buss

Articles

This study assessed the properties and toxicity (water cress germination trials) of 38 waste-derived, novel biochar-mineral composites (BMCs) produced via slow pyrolysis and hydrothermal carbonization (hydrochars). The biochars were produced from sewage sludge and compost-like output (CLO) by varying the type of mineral additive (zeolite, wood ash and lignite fly ash), the mineral-to-feedstock ratio and the carbonization process. While pure hydrochars completely inhibited germination of water cress, this effect was ameliorated by mineral additives. Seedlings grew best in pyrolysis chars and while wood ash addition decreased plant growth in many cases, 1:10 addition to CLO doubled germination rate. The factors …

Failure Of The Alexander Dam Embankment And Reconstruction Using Drainage Mitigation On Kauai, Hawaii, 1930-1932, Kerry D. Cato, J. David Rogers

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

Alexander Dam is a hydraulic fill earth dam and the second-highest embankment dam in Hawaii, having been built in 1929-1932 on the south side of the Hawaiian island of Kauai to provide irrigation for McBryde Sugar Company Ltd. It was constructed across Wahiawa Stream mauka (Hawaiian for "stream that comes from the mountains," literally "toward the mountains"), upstream of Kalaheo, to store 800 million gallons (5 million m3) of water to irrigate sugarcane fields. The embankment dam was intended to have a maximum height of 125 ft (38 m), a crest length of 620 ft (189 m), and a maximum …