Mechanical Engineering Commons^™

A Solar‐Driven Membrane‐Based Water Desalination/Purification System, Abdellah Shafieian Dastjerdi

Theses: Doctorates and Masters

Lack of fresh water has turned into one of the major challenges of the world in the present century. Desalination of brackish or seawater has been proven to be one of the best solutions to cope with this global challenge. Among all the desalination methods, Membrane Distillation (MD) is well known as a cost effective and profitable technology for treating saline water. However, higher energy consumption compared to other separation techniques has been reported as MD’s main drawback. That is why the application of solar energy to provide the thermal energy requirement of MD modules has been the focal point …

Integration Of Heat Pipe Solar Water Heating Systems With Different Residential Households: An Energy, Environmental, And Economic Evaluation, Abdellah Shafieian, Mehdi Khiadani

Research outputs 2014 to 2021

This study presents a detailed methodology for evaluating the energy, environmental, and economic contributions of heat pipe solar water heating (HPSWH) systems in various households. The hot water consumption patterns of Perth residents in Australia in one, two, and four-occupant houses are extracted in hourly basis throughout a year. The annual performance of the system is evaluated based on parameters such as saved energy, solar fraction, avoided CO₂ emission, saved money, and payback period. Moreover, an experimental rig is designed, manufactured, and tested. The results show that the contribution of the solar system in meeting the hot water demand …

Indirect Thermosiphon Flat-Plate Solar Collector Performance Based On Twisted Tube Design Heat Exchanger Filled With Nanofluid, Mahmoud Eltaweel, Hazem Hussien, Ahmed A. Abdel-Rehim

Mechanical Engineering

No abstract provided.

Energetic And Exergetic Analysis Of A Heat Pipe Evacuated Tube Solar Collector Using Mwcnt/Water Nanofluid, Mahmoud Eltaweel, Ahmed A. Abdel-Rehim

Mechanical Engineering

Increasing the energy demand and the limited availability of conventional energy sources are the main challenges to secure the human future. Solar energy is an attractive source of energy to ensure the sustainability of energy in this world for now and for the future. Evacuated tube solar collector is a solar thermal collector mostly used for domestic applications. The replacement of the working fluid with nanofluid can enhance the heat transfer even for low temperature applications. The effect of multi-walled carbon nanotubes and water nanofluid as working fluid in evacuated tube solar collector is used to experimentally investigate the energy …

In-Situ X-Ray Imaging Of The Selective Laser Melting Process, Meelap M. Coday

Masters Theses

"Fusion-based metal additive manufacturing (AM) has garnered much interest in recent decades. Despite the popularity of fusion-based AM technologies such as selective laser melting (SLM), there are still fundamental questions and uncertainties that need to be addressed. In this work, we focus on the understanding of the undercooling in the SLM process and the uncertainties induced by the laser beam size, power, and scan speed. First, we report the estimation of undercooling in the SLM process from the solidification rate measured by in-situ high-speed synchrotron x-ray imaging, based on the dendrite growth velocity model. The undercooling changes as a function …

Influence Of Input Energy On Mechanical Properties Of Laser Powder Bed Fused Aisi 304l Stainless Steel, Tan Pan

Masters Theses

“Powder Bed Fusion process with selective laser melting technique is popularly adopted in additive manufacturing area on account of its layer by layer manufacturing fashion capable of fabricating components with complex internal and external geometries and structures. However, the process-property map is unique and vital for different materials and AM configurations used for fabrication. The process parameter is identified as a significant factor that heavily influences the properties and performances of the printed materials.

Current work aimed to extend the existing knowledge on Laser Powder Bed Fusion fabricated AISI 304L by accessing the influence of varying energy input on the …

Performance Evaluation Of Alsi10mg Fabricated By A Selective Laser Melting Process, David Michael Murphy

Masters Theses

“Selective laser melting is becoming a widely used additive manufacturing technique that melts metal powder in a layer by layer process in order to build a desired part or geometry. Like many additive processes, selective laser melting allows for fabrication of parts with complex geometries. In order to fabricate a fully dense part there are a number of variables to take into account including: powder characteristics, laser parameters, and environmental parameters. Each of these variables can affect the microstructure and thus the mechanical performance of an additively manufactured part. In this work, the aluminum alloy AlSi10Mg was investigated. AlSi10Mg is …

Mid-Infrared Chiral Metsurface Coupling With Molecular Vibration, Md Shamim Mahmud

Masters Theses

“The mid-infrared design of chiral metamaterial shows a tremendous absorption capability of infrared rays, and it has the significant application of circular dichroism based device development. Plasmon-phonon coupling is one of the application of metamaterial that provides a new path for tailoring the surface in the nanoscale, which is also applicable in molecules detection. It is possible to change the Plasmon-Phonon coupling strength not only through the chemical change of molecules but also by changing the metamaterial light-matter interaction property. So far, linearly polarized light shows the strong coupling between metamaterial and molecules. However, it is possible to observe strong …

Combining Laser Aided Ablation And Polishing To Minimize Surface Roughness Of Additively Manufactured Aluminium Components, Sahil Bipinkumar Patel

Masters Theses

“The surface roughness of additively manufactured parts is much higher than the acceptable range for most applications, thus post-processing is needed to qualify these parts for use. Laser polishing can be used to bring the surface roughness in an admissible range, but if the initial roughness is very high then the energy density for the polishing process needs to be very high to achieve a significant reduction in roughness. This high energy density can produce many process defects. Also, laser polishing alone cannot get rid of high wavelength asperities. Any waviness in the part can be linked with initial waviness …

Utility-Scale Solar Pv Performance Enhancements Through System-Level Modifications, Andrew D. S. Glick, Naseem Ali, Juliaan Bossuyt, Marc Calaf, Raul Bayoan Cal

Mechanical and Materials Engineering Faculty Publications and Presentations

Performance of solar PV diminishes with the increase in temperature of the solar modules. Therefore, to further facilitate the reduction in cost of photovoltaic energy, new approaches to limit module temperature increase in natural ambient conditions should be explored. Thus far only approaches based at the individual panel level have been investigated, while the more complex, systems approach remains unexplored. Here, we perform the first wind tunnel scaled solar farm experiments to investigate the potential for temperature reduction through system-level flow enhancement. The percentage of solar irradiance converted into electric power depends upon module efficiency, typically less than 20%. The …

Impact Of Particle Injection On Gas Flow At Elevated Pressure: A Numerical Study, Ansan Pokharel

Graduate Theses, Dissertations, and Problem Reports (ETD)

Modeling of a turbulent two-phase gaseous-solid flow still faces challenges. The present study is devoted to two-phase flow in an annular pipe (hollow cylinder) operating at an elevated pressure of 15 bar and moderate Reynolds numbers of circa 6 x 10³. The influence of the various factors – such as the particle loading, the interaction between the phases, and turbulent dispersion – on the flow dynamics is systematically studied by means of the computational simulation employing the ANSYS FLUENT commercial package. To be specific, particle loading with a volumetric fraction of 1.2 % is defined as high particle …

Doping With Rare Earth Elements And Resultant Nano-Inclusions On The Electrical And Thermal Properties Of The Mis-Fit Layered Thermoelectric Oxide, Geoffroy Gauneau

Graduate Theses, Dissertations, and Problem Reports (ETD)

Thermoelectric generators produce electricity by directly converting temperature differences into electrical energy through Seebeck effect. Thermoelectric generators possess many unique features, such as having no moving part and being very reliable with a relatively long lifespan once built. They are solid-state waste heat harvesters. With various waste heat available throughout many industries, thermoelectric generators could offer economically competitive renewable energy. The current state of the art thermoelectric materials includes materials with relatively toxic elements and must work under vacuum, making them quite expensive to produce. Among the various thermoelectric materials, ceramic oxides have been proved to be more chemically stable …

Effects Of Supplementary Cementitious Materials On Early-Age Tensile Creep And Shrinkage Of Concrete, Lucas James Bucklen

Graduate Theses, Dissertations, and Problem Reports (ETD)

Determination of early-age tensile creep properties is critical for the performance of mass concrete structures at an early age. Due to the stress relaxation that tensile creep induces in concrete structures, accurate quantification of creep deformation is needed to determine the stress profile of the structure. Conventional methods of measuring tensile creep include the direct tension test where the concrete is subject to constant tensile stress. This method requires large quantities of concrete with embedded strain gauges which can only be used once. In this paper, the tensile creep parameters of concrete are found by using the restrained concrete ring …

Modeling And Tuning Of Cvt Systems For Sae® Baja Vehicles, Sean Sebastian Skinner

Graduate Theses, Dissertations, and Problem Reports (ETD)

Continuously variable transmission (CVT) describes a family of transmission styles. These systems serve the same purpose as their traditional counterparts; transmitting power while offering a variable gearing ratio. The difference lies in the CVT’s ability to change ratio continuously between a minimum and maximum without halting power transfer. They offer many benefits of an automatic transmission while being significantly lighter. For this reason, CVTs are often used on Baja SAE^® vehicles to control gearing ratio.

WVU’s Baja team has used mechanical CVTs for many decades. These systems are simpler in the sense that they don’t require power to operate. …

Investigating The Effects Of Flue Gas Injection, Hot Water Distribution, And Fill Distribution On Natural Draft Wet Cooling Tower Performance, John Stapleton

Senior Honors Theses

Natural draft wet cooling towers (NDWCT) are a common method of heat removal in powerplants. This study employs a numerical cooling tower model developed by Eldredge, Benton & Hodgson (1997) to examine whether utilizing nonuniform water, fill profiles, and flue gas injection can improve NDWCT efficiency. The results show that each of these variables can be optimized to lower outlet water temperature. Within the range tested for each parameter, the water profile had the most significant effect on outlet water temperature, followed by the flue gas temperature and then the fill profile. The optimum parameter combination reduced the predicted outlet …

Deep Learning Of Nonlinear Dynamical System, Aditya Wagh

Dissertations, Master's Theses and Master's Reports

A data-driven approach, such as neural networks, is an alternative to traditional parametric-model methods for nonlinear system identification. Recently, long Short- Term Memory (LSTM) neural networks have been studied to model nonlinear dynamical systems. However, many of these contributions are made considering that the input to the system is known or measurable, which often may not be the case. This thesis presents a method based on LSTM for output-only modeling, identification, and prediction of nonlinear systems. A numerical study is performed and discussed on Duffing systems with various cubic nonlinearity.

A Neural Network Approach To Estimate Buoy Mooring Line Sensor Deflection, Tom Price

Dissertations, Master's Theses and Master's Reports

Instrumented moorings are often used to measure characteristics, such as temperature and current, over the water column. However, the moorings deflect from the effects of currents and waves, which could lead to innacurate measurements. In this work, a computationally efficient method to compensate for mooring sensor position errors is developed. The two-step process first uses a hydrodynamic model of the buoy and mooring line system to create estimated mooring line deflections in a steady current. A neural network model is trained to approximate the hydrodynamic model’s mooring line displacement given the spatial location of the buoy and current profile measurements. …

Sensitivity And Uncertainty Quantification Of Continuum And Stochastic Bond Dissociation Kinetics Based Cohesive Laws, Rishabh Awasthi

Dissertations, Master's Theses and Master's Reports

Polymeric adhesives are being extensively used to develop light weight and durable Composite Materials which are have been employed in automotive, aeronautical, medical industry. Polymeric adhesives undergo failure due to relative opening sliding of bonded interfaces which requires a need to characterize the fracture mechanism. Numerous experiments are conducted to predict the fracture response for Mode-I, II,III and numerical simulations are employed to inversely calibrate the material parameters governing the constitutive laws. Cohesive zone models are largely employed in fracture mechanics to predict failure of interfaces undergoing large plastic deformations. The objective of this report is to employ the cohesive …

Analysis Of A Circular Resonant Plate For Shock Testing, Jon Markl

Dissertations, Master's Theses and Master's Reports

Designing a resonant plate for shock test specifications involves an understanding of how a system will respond with a given set of input and output locations in all three directions. To investigate how to effectively change the off-axis responses to meet test specifications, a finite element model (FEM) was created and examinations of input location/angle of impact, placement of the test fixture, and placement of the impact pad were conducted. The primary tool used to determine how a structure will respond to a given input at a given output on the test structure was done using the shock response spectra …

Experimental Characterization Of Spool Valve Flow Noise, Zachary Cohen

Dissertations, Master's Theses and Master's Reports

The purpose of this research was to experimentally measure the flow noise produced by a spool valve and compare with measurements of orifice flow noise to reduce flow noise modelling complexity. The similarities and differences are compared over a range of volume flow rates, back pressures, and cross section areas. The impact of down stream boundary conditions on the flow noise are also examined. The results are generalized and plotted against Froude number. The valve results are curve fit to generate empirical equations that can be used to predict flow noise under typical operating conditions. The valve and orifice data …

Design, Build, And Analysis Of A Compressed Natural Gas Direct Injection Compression Ignition Single Cylinder Research Engine, Tyler Miller

Dissertations, Master's Theses and Master's Reports

Both experimental and simulation efforts have been employed to further advance the design and build of a single cylinder research engine. The engine will aid in advancing technology and understanding the operation of compression-ignition (CI) engines using natural gas within the heavy-duty engine industry. The basis for the engine is a Cummins 15L ISX engine that has been modified, retrofitted, and instrumented to allow for late-cycle direct-injection of high-pressure compressed natural gas. Along with the engine build, a one-dimensional GT-Power simulation model has been created and used to analyze the engine operation and specify components including the engine compression ratio …

A Study Of Model-Based Control Strategy For A Gasoline Turbocharged Direct Injection Spark Ignited Engine, Xin Wang

Dissertations, Master's Theses and Master's Reports

To meet increasingly stringent fuel economy and emissions legislation, more advanced technologies have been added to spark-ignition (SI) engines, thus exponentially increase the complexity and calibration work of traditional map-based engine control. To achieve better engine performance without introducing significant calibration efforts and make the developed control system easily adapt to future engines upgrades and designs, this research proposes a model-based optimal control system for cycle-by-cycle Gasoline Turbocharged Direct Injection (GTDI) SI engine control, which aims to deliver the requested torque output and operate the engine to achieve the best achievable fuel economy and minimum emission under wide range of …

Real-Time Predictive Control Of Connected Vehicle Powertrains For Improved Energy Efficiency, Joseph Oncken

Dissertations, Master's Theses and Master's Reports

The continued push for the reduction of energy consumption across the automotive vehicle fleet has led to widespread adoption of hybrid and plug-in hybrid electric vehicles (PHEV) by auto manufacturers. In addition, connected and automated vehicle (CAV) technologies have seen rapid development in recent years and bring with them the potential to significantly impact vehicle energy consumption. This dissertation studies predictive control methods for PHEV powertrains that are enabled by CAV technologies with the goal of reducing vehicle energy consumption.

First, a real-time predictive powertrain controller for PHEV energy management is developed. This controller utilizes predictions of future vehicle velocity …

Phase Field Fracture Modeling Of Chemically Strengthened Glass, Parag Nikam

Dissertations, Master's Theses and Master's Reports

The objective of the report is to implement the phase-field model in the Abaqus standard to compute the fracture properties of a glass strengthened by an ion-exchange process. Implemented the phase-field model which is based on the rate-independent variational principle of diffuse fracture in Abaqus standard software using the UEL and UMAT subroutines. SDVINI subroutine is used to give the residual stress or prestress conditions to simulate the stress profile of strengthened glass. Studied the effect of parameters such as length scale parameter and step size and the optimum parameters are selected. The experimental model of chemically strengthened glass is …

Numerical Investigation Of Spray Characterization Of Heater-Gdi System, Ashwin Karthik Purushothaman

Dissertations, Master's Theses and Master's Reports

Gasoline engines require fuel enrichment at low temperature cranking (cold start) conditions for efficient engine operation. Since the amount of fuel injected is high at cold start to compensate low fuel evaporation, fuel sprays tend to impinge on the cold surfaces of the piston and cylinder walls leading to the formation of excessive unburned hydrocarbons. One of the ways to ensure reliable cold start performance and to reduce UHC emissions is to have the fuel subjected to preheating. The objective of this study is to investigate the effects of fuel preheating on Gasoline Direct Injection sprays to improve the mixture …

Optimization Of Shape And Control Of Linear And Nonlinear Wave Energy Converters, Jiajun Song

Dissertations, Master's Theses and Master's Reports

In this dissertation, we address the optimal control and shape optimization of Wave Energy Converters. The wave energy converters considered in this study are the single-body heaving wave energy converters, and the two-body heaving wave energy converters. Different types of wave energy converters are modeled mathematically, and different optimal controls are developed for them. The concept of shape optimization is introduced in this dissertation; the goal is to leverage nonlinear hydrodynamic forces which are dependent on the buoy shape. In this dissertation, shape optimization is carried out and its impact on energy extraction is investigated. In all the studies conducted …

Dynamic Testing: An Experimental Approach To Defect Identification In Additive Manufactured Parts, Aimee Allen

Dissertations, Master's Theses and Master's Reports

Today’s additive manufacturing (AM) industry produces specialized parts at low volume or with complex geometries. Traditional testing methods are effective, but costly and time consuming to perform. The AM industry lacks an optimized testing method for identifying internal defects that occur in parts. The evaluation of multiple parts printed on the same build plate for internal defects using various nondestructive (dynamic) testing techniques is presented. From these experiments, perspective was gained on when and how dynamic testing can be used to find defects. Insight gained from these experiments can help the industry in future testing for internal defects.

Multiscale Modeling Of Carbon Fibers/Graphene Nanoplatelets/Epoxy Hybrid Composites For Aerospace Applications, Hashim Al Mahmud

Dissertations, Master's Theses and Master's Reports

Significant research effort has been dedicated for decades to improve the mechanical properties of aerospace polymer-based composite materials. Lightweight epoxy-based composite materials have increasingly replaced the comparatively heavy and expensive metal alloys used in aeronautical and aerospace structural components. In particular, carbon fibers (CF)/graphene nanoplatelets (GNP)/epoxy hybrid composites can be used for this purpose owing to their high specific stiffness and strength. Therefore, this work has been completed to design, predict, and optimize the effective mechanical properties of CF/GNP/epoxy composite materials at different length scales using a multiscale modeling approach. The work-flow of modeling involves a first step of using …

Increasing Access To Pv Technology Through Sustainable Racking: A Review Of Existing Literature And Ground Mounted Fixed Tilt Designs, And What Can Be Done Next, Parijata Prabhakara

Dissertations, Master's Theses and Master's Reports

There is a lack of literature on the structural balance of systems (BOS), also called racking, for ground mount, fixed-tilt solar PV systems. Literature that exists discusses mostly rooftop racking and installations, additional wind loading, and weight considerations imposed on roofs, and little guidance is provided in building codes. The lack of peer-reviewed guidance on design requirements for domestic and large-scale application solar PV racking systems leaves most consumers relying on expensive, patented, off-the-shelf hardware. As PV cell technology and module costs have improved, we can start to focus on PV BOS improvements (particularly racking) and move towards sustainable designs …

Generative Design In Energy Efficient Buildings, Johanna Thill

Dissertations, Master's Theses and Master's Reports

This is an investigative report on the use of generative design and genetic algorithms in the design of energy-efficient buildings. It focuses on a workflow using Project Refinery© and Dynamo© in Revit® for multi-objective optimization and visualization, and Honeybee© for daylighting analysis. The workflow was not about to run completely due to instability in Dynamo, however daylighting analysis and visualizations were produced separately from demonstrations of Refinery. It concludes that while genetic algorithms have potential to be useful in energy-efficient building design, these programs are not yet fully developed and difficult to use without extensive background knowledge and fluency in …