Mechanical Engineering Commons^™

Conical Orbital Mechanics: A Rework Of Classic Orbit Transfer Mechanics, Cian Anthony Branco

Mechanical & Aerospace Engineering Theses & Dissertations

Simple orbital maneuvers obeying Kepler’s Laws, when taken with respect to Newton’s framework, require considerable time and effort to interpret and understand. Instead of a purely mathematical approach relying on the governing relations, a graphical geometric conceptual representation provides a useful alternative to the physical realities of orbits. Conic sections utilized within the full scope of a modified cone (frustum) were employed to demonstrate and develop a geometric approach to elliptical orbit transformations. The geometric model in-question utilizes the rotation of a plane intersecting the orbital frustum at some angle β (and the change in this angle) in a novel …

Improvement Of Labyrinth Seal Leakage Rates Using Additive Manufacturing, Austin L. Gasbarra

Master's Theses

The growing popularity of additive manufacturing in commercial applications has al- lowed for new ideas and new ways of thinking when designing components. Further optimization at the component level is possible, though powder metallurgy is in its infancy. This study explores the possibility of using additive manufacturing to develop better labyrinth seals in turbomachinery. Labyrinth seals have a torturous fluid path with high losses, thus limiting the amount of fluid leakage. These types of seals can be non-rotating, allowing them to better take advantage of the additive manufacturing process due to the absence of rotating stresses. Labyrinth seal performance is …

Understanding The Effects Of Long-Duration Spaceflight On Fracture Risk In The Human Femur Using Finite Element Analysis, Keyanna Brielle Henderson

Master's Theses

Long-duration spaceflight has been shown to have significant, lasting effects on the bone strength of astronauts and to contribute to age-related complications later in life. The microgravity environment of space causes a decrease in daily mechanical loading, which signals a state of disuse to bone cells. This affects the bone remodeling process, which is responsible for maintaining bone mass, causing an increase in damage and a decrease in density. This leads to bone fragility and decreases overall strength, posing a risk for fracture. However, there is little information pertaining to the timeline of bone loss and subsequent fracture risk.

This …

Finite Element Analysis Of Total Knee Arthroplasty, Sean Yueh

Master's Theses

The total knee arthroplasty (TKA) has become one of the most successful procedures in all of medicine, with an average of over 966,000 operations performed a year. Since its introduction in 1968, the TKA’s surgical process and implant designs have continuously been improved to increase survivability. However, the need for a revision TKA – due to aseptic loosening – continues to be a problematic aspect of the procedure. Stress shielding induced by different design parameters of the implant has generated controversy in the determination of an ideal configuration. The purpose of this study is to investigate how implant design parameters …

The Optimization Of Efficiency And Infrastructure For Modern Potable Water Treatment Plants, Brent A. Dekock

Theses and Dissertations

The USDOE Industrial Assessment Centers (IACs) is a program that is designed to help small and medium-sized manufacturing facilities reduce their overall costs and improve energy efficiency. This includes improving potable water treatment plants which supply water throughout the country. This thesis covers the process of how IAC branches and water treatment facilities generally operate, as well as several assessment recommendations that have been developed by a branch of the IAC for several water treatment plants based in the Rio Grande Valley of Texas. The steps of the assessment and water treatment process are described, and several cost saving measures …

Toward Understanding Underlying Mechanisms Of Drag Reduction In Turbulent Flow Control, Alex Rogge

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

The underlying mechanisms of three different flow-control strategies on drag reduction in a turbulent channel flow are investigated by direct numerical simulations. These strategies include the addition of a small concentration of long-chain polymers into a fluid, the incorporation of slip surfaces, and the application of an external body force. While it has been believed that such methods lead to a skin-friction reduction by controlling near-wall flow structures, the underlying mechanisms at play are still not as clear. In this study, a temporal analysis is employed to elucidate underlying drag-reduction mechanisms among these methods. The analysis is based on the …

Direct Solar Absorption Nanoparticle Doped Membranes For A Hybrid Membrane Distillation And Photovoltaic Cell, Alejandro Espejo Sanchez

Boise State University Theses and Dissertations

The growing demand for clean water supplies is driving the need for an innovative approach of water desalination. Developing a method for treating water with high salinities is possible with membrane distillation (MD). Additionally, MD is very attractive for pairing with solar energy due to the low temperature requirements. The integration of a membrane distillation system with a photovoltaic (PV) system will result in the co-production of electricity and clean water, thereby improving the economics of MD. Such a hybrid system will directly absorb thermal energy in the membrane for desalination while taking advantage of the spectrally selective nature of …

In Vitro Method To Quantify And Visualize Volumetric Wear In Meniscus Subjected To Joint Loading Using A 3d Optical Scanner, Kate J. Benfield

Boise State University Theses and Dissertations

The menisci are fibrocartilaginous soft tissues that act to absorb and distribute load across the surface of the knee joint. As a result of mechanical wear and large repetitive loading, meniscus tissue can begin to breakdown, or degenerate. Meniscus degeneration increases the risk of tearing, weakened tissue integrity, and the progression of osteoarthritis. Therefore, it is imperative to understand the wear behavior of whole human meniscus to identify conditions that may significantly increase the risk of degeneration.

The objective of this study is to develop and validate an in vitro methodology for characterizing volumetric wear behavior in whole human meniscus …

Validation Of Novel Obstructive Sleep Apnea Treatment With Silicone Gel Experimental Models, Dustin Walter Burd

UNLV Theses, Dissertations, Professional Papers, and Capstones

Predictive modeling to increase treatment success rates for surgical procedures is becoming more common in the scientific community. For obstructive sleep apnea (OSA), modeling has been predominately performed using computers as opposed to experimental models. Computer simulation saves time by eliminating the need to fabricate complex experimental models but comes at the expense of insight gained through physical observations made in real time. Experimental models for studying OSA are needed to validate computational work, provide perspective on anatomical scale and demonstrate complex deformations in real time. This work addresses prior hurdles in experimental model fabrication with a novel process using …

Minimizing Visual Defects Through Augmentation Of Computer Aided Diamond Rough Planning, Abhijith Prabhu

UNLV Theses, Dissertations, Professional Papers, and Capstones

Many computer aided design systems today utilize a workflow where physically accurate rendering of the product is not a functional component of its design process. This gap in workflow can lead to a sub optimal product or even a longer iterative design process in instances where a product's visual attributes and aesthetics are one their primary functional characteristic.

Diamonds are graded on their carat, color, clarity and cut, referred to as the 4Cs of a diamond; a standard set by G.I.A. and universally agreed upon. The cut of a diamond significantly affects the rest of the characteristics as it modifies …

Constitutive Modeling Of Force-Controlled Fatigue Testing In Human Meniscus Tissue, Bradley Scott Henderson

Boise State University Theses and Dissertations

The meniscus is a wedge-shaped fibrocartilaginous tissue located between the femur and tibia that helps stabilize the knee and protect the underlying cartilage. There are 2.5 million reported knee injuries each year, making it the most injured joint in the human body. Nearly twenty percent of these injuries are due to a torn meniscus, leading to over half a million meniscus surgeries performed in the United States annually. Therefore, it is critical to understand the failure modes of meniscus tissue to prevent these debilitating injuries. A failure mode that accounts for one-third of all meniscus injuries is repeated exposure to …

Large Displacement J-Integral Double Cantilever Beam (Dcb) Test Method For Mode I Fracture Toughness, Joshua Gunderson

Boise State University Theses and Dissertations

The J-integral is used to develop an alternative double cantilever beam (DCB) test method for the Mode I fracture toughness suitable for both small and large displacements. The current focus is the experimental determination of the Mode I interlaminar fracture toughness of composite materials, but the method is generally applicable to other similar tests and material systems, such as to the Mode I fracture toughness of adhesives. A series of five identical specimens are tested to compare the linear-elastic fracture mechanics method recommended by ASTM, which makes use of linear beam theory with root rotation, large displacement, and end …

Molecular Mechanisms And Design Of Hydrogen-Bonded Materials For Thermal Applications, Jinlong He

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Heat transfer at the nanoscale plays an important role in determining the reliability and performance of many innovative advanced materials technologies such as nanoelectronics, semiconductor, biomedical devices, polymers, and composites. Extensive efforts have been made to design materials with extraordinary thermal properties. However, fundamental understanding of heat transfer in many of these materials is still not lacking, because the thermal transport processes are governed by several factors including molecular morphology and chemical bonding. Among these factors, the atomic bonding between two dissimilar materials or within single materials is of particular interest due to its ubiquity and importance in physical processes. …

A Low-Cost Secure Iot Mechanism For Monitoring And Controlling Polygeneration Microgrids, Josué Martínez-Martínez, Diego Aponte-Roa, Idalides Vergara-Laurens, Wayne Weaver

Michigan Tech Publications, Part 1

The use of Internet-connected devices at homes has increased to monitor energy consumption. Furthermore, renewable energy sources have also increased, reducing electricity bills. However, the high cost of the equipment limits the use of these technologies. This paper presents a low-cost secured-distributed Internet of Things (IoT) system to monitor and control devices connected in a polygeneration microgrid, as a combined power system for local loads with renewable sources. The proposed mechanism includes a Wireless Sensor Actuator Networked Control System that links network nodes using the IEEE 802.15.4 standard. The Internet communication enables the monitor and control of devices using a …

A Modified Peng-Robinson Cubic Equation Of State Based On Bayesian Framework, Wei Chen

Theses and Dissertations

Peng-Robinson cubic equations of state (PR-EoSs) as one of the most popular two-parameter cubic equations of state (2P-EoSs) are widely used to calculate thermodynamic properties of pure substances and their mixtures. However, the prediction accuracy of 2P-EoSs varies significantly among different substances due to its intrinsic limitation. To this end, many modifications have focused on changing the dependence structure of 𝛼 function with temperature for PR-EoS to enhance prediction accuracy. In this paper, we propose a Bayesian framework to calibrate a new 𝛼 function, which is a bias-corrected parametrized model form for the PR-EoS. The developed PR-EoS with the calibrated …

A Finite State Automata-Based Description Of Device States For Function Modeling Of Multi-State Technical Devices, Ahmed Mohammed Sobhan Chowdhury

Theses and Dissertations

Many modern and innovative design problems require multi-modal, reconfigurable solutions. Function modeling (FM) is a common tool used to explore solutions in early stages of mechanical engineering design. Currently, function structure representations do not abet the modeling of formally-defined reconfigurable function models as graph-based function models used in early-stage systems design usually represent only one operational mode of the system. Currently there is a need, but no rigorous formalism to model multiple possible modes in the model and logically predict the behavior of the system as it transitions between the modes. Additionally, function modeling representations will benefit from dynamically capturing …

Development Of Nirs Based Noninvasive Cerebrovascular Regulation Assessment, Stephanie Marie Miller

Theses and Dissertations

Alterations to cerebral blood flow (CBF) have been implicated in diverse neurological conditions, including mild traumatic brain injury, microgravity induced intracranial pressure (ICP) and intraocular pressure (IOP) increases, and mild cognitive impairment. Near infrared spectroscopy (NIRS)-measured regional cerebral tissue oxygen saturation (rSO2) provides an estimate of oxygenation of the interrogated cerebral volume that is useful in identifying trends and changes in oxygen supply to cerebral tissue and has been used to monitor cerebrovascular function during surgery and ventilation. In this study, CO2-inhalation-based hypercapnic breathing challenges were used as a tool to simulate CBF dysregulation, and NIRS was used to monitor …

Nonlinear Frequency Tuning Of Pre-Curved Micro-Scale Beams, Mackenzie Rae Robatin

Theses and Dissertations

Micro-electromechanical systems (MEMS) have many common advantages in applications due to their small size and ability to integrate with electronics. For MEMS with vibrating elements, other advantages include their tunable resonant frequencies and the frequency range in which the systems operate. Also, the damping in these devices is often so light that it is nearly negligible, resulting in sharp resonance peaks with good frequency selectivity. Most such devices are designed to operate in their linear range. However, large amplitudes are often desired in order to reduce the relative effects of noise. In such cases, due to mechanical and electrostatic nonlinear …

Optimal Onboard Renewable Energy Charging Method To Improve Micro-Autonomous Underwater Vehicle Deployment Life, Brooklynn Dawn Byford

Theses and Dissertations

This study is an investigation of various methods for recharging a micro autonomous underwater vehicle (μAUV) onboard using renewable energy sources while deployed at sea. The goal of this project is to determine the optimal onboard renewable energy design method to be used to prolong the deployment life of a μAUV. This project specifically targeted vehicles specifications and designs similar to the Riptide Autonomous Solutions’ μAUV[1], which was used for this study. Concluding results are based on the following factors: power generation versus time, structural integrity, and design complexity. The three design method categories investigated are as follows: solar energy, …

Finite Element Method For Assessment Of Air Cushion Skirt Performance, Thomas Arthur Lipscomb

Theses and Dissertations

The objective of this thesis is to create a method of simulating the performance of new materials for use in air cushion vehicle skirts. These systems currently exhibit unacceptable design lifetimes to be considered for widespread adoption, except in specific applications such a military or rapid transport, where high cost is not an obstacle. This project also focuses on using a new high strain to failure resin system that has recently been developed, in combination with high performance reinforcing fibers, to increase the lifespan of the skirt systems. Using industry-standard finite element modelling (FEM) software, a 3d model of the …

Extreme Response Analysis Of A Site-Specific Offshore Wind Turbine And Offshore Wind Farm Layout Optimization, Xiaosen Xu

Theses and Dissertations

Offshore floating wind turbines have been developed in deep water where bottom-fixed offshore wind turbines are cost-prohibitive. Gulf of Maine has one of the greatest potential wind energy on the east coast. A detailed analysis of metocean data is essential for the dynamic simulation of the floating offshore wind turbine and the offshore wind farm layout optimization. Wave scatter diagram represents the joint probability of significant wave height and peak periods. In the wind energy industry, turbulence intensity is defined as the standard deviation of the horizontal wind speed divided by the average wind speed over certain time period. Uniform …

Dynamic Body-Weight Support To Boost Rehabilitation Outcomes In Patients With Non-Traumatic Spinal Cord Injury: An Observational Study, Justin P. Huber, Lumy Sawaki

Neurology Faculty Publications

BACKGROUND: Dynamic body-weight support (DBWS) may play an important role in rehabilitation outcomes, but the potential benefit among disease-specific populations is unclear. In this study, we hypothesize that overground therapy with DBWS during inpatient rehabilitation yields greater functional improvement than standard-of-care in adults with non-traumatic spinal cord injury (NT-SCI).

METHODS: This retrospective cohort study included individuals diagnosed with NT-SCI and undergoing inpatient rehabilitation. All participants were recruited at a freestanding inpatient rehabilitation hospital. Individuals who trained with DBWS for at least three sessions were allocated to the experimental group. Participants in the historical control group received standard-of-care (i.e., no DBWS). …

The Effect Of Guide Vane Opening Variations And Total Blades On Cross Flow Turbine Performance Using Computational Fluid Dynamic, Muhamad Akbar Navis, Heru Suryanto, Putut Murdanto

Journal of Mechanical Engineering Science and Technology (JMEST)

Indonesia is an agrarian country that continuously produces water, so it has the potential to develop a hydroelectric power plant. Computational Fluid Dynamic (CFD) application could be used to be an economical, quick, and efficient approach to improve the engineering design and turbine performance. This research aimed to find the effect of guide vane opening variations and total blades on cross-flow turbine performance using CFD simulation. This research used experimental modelling method with ANSYS program for turbine design with 22, 24, and 26 turbine blades and guide vane opening variations of 12°, 16°, 20°, 24°, and 36°. The data were …

Energy And Exergy Efficiency Of Double Slope Passive Solar Still, Jandri Fan Ht Saragi, Wawan Septiawan Damanik

Journal of Mechanical Engineering Science and Technology (JMEST)

Solar desalination functions to filter water, both sea water and brackish water, to produce clean water that is fit for consumption with energy from the sun. Solar energy is a renewable energy source that has been widely studied for its use. One of its uses is in a double slope passive solar still where the sun is the main source. Energy and exergy obtained from solar energy are not all used to evaporate water in the desalination system, so it is necessary to calculate efficiency energy and exergy in the system. This study aims to obtain data on the amount …

Characteristics Biolubricant Enriched With Nanoparticle Additives: A Review, Zhahra Hanif Sholiha, Gaguk Jatisukamto

Journal of Mechanical Engineering Science and Technology (JMEST)

The engine movement mechanism is a system composed of machine elements that contact or rub against each other between these surfaces. Surfaces that rub against each other will cause a friction force that causes wear on the surface, so it requires energy to fight the friction force. Lubricants are needed to reduce friction and reduce wear rates, where lubricants are generally made of mineral materials. Lubricants made from synthetic materials are non-renewable and cause environmental problems. The development of biolubricants as lubricating materials based on animal fats or vegetable oils is continuously being carried out. This study aims to observe …

Optimization Of Stir Casting Of Aluminum Matrix Composites (Amcs) With Filler Of Recycled Glass Powder (Rgp) For The Mechanical Properties, Yusup Hendronursito, Tumpal Ojahan, Anang Anshori, Asep Yunanto

Journal of Mechanical Engineering Science and Technology (JMEST)

A study of making Aluminum Matrix Composites (AMCs) uses recycled glass powder (RGP) as a filler has been carried out through the stir casting process. The experimental design uses the Taguchi method of 3^3 orthogonal array L9 with the parameters of powder size (20>x> 80, 80>y> 200, 200>z> 325), percentage of filler vs matrix (2%, 7%, 12%), and stirring time (30 Seconds, 3 Minutes, 12 Minutes). The optimum conditions for the hardness of Al-GRp composites were obtained from specimens with Mesh powder size parameters 200> z> 325, the percentage of glass vs aluminum powder was 12% wt, …

Surface Properties And Adsorption Capacities Of Rice Bran-Activated Carbon, Dewa Ngakan Ketut Putra Negara, Tjokorda Gde Tirta Nindhia, Wayan Nata Septiadi

Journal of Mechanical Engineering Science and Technology (JMEST)

The growing need for activated carbon requires alternative raw materials to replace non-renewable raw materials whose existence is decreasing. Biomass is a very promising precursor, one of which is from rice bran. This research concerns the development of activated carbon derived from rice bran. Carbonization was carried out at 600 OC and physically activated with nitrogen flow rates of 150 mL/min for 40, 80, and 120 minutes. The activated carbons produced (AC-D40, AC-D80, and AC-D120) were characterized to determine the surface properties, surface morphology, and adsorption capacity for nitrogen and blue methylene adsorptions. The results showed that activated carbon that …

Design Of Savonius Vertical Axis Wind Turbine For Vehicle, Filian Arbiyani, Fernando Pranata Lasut

Journal of Mechanical Engineering Science and Technology (JMEST)

The use of cellular phones is increasing in society, but due to the limited battery capacity of cell phones, it is necessary to charge the battery when travelling in the long distances. The Savonius type wind turbine has a potential as an energy source harvesting the wind energy flowing around the car. However, due to the available space on the car, careful design of Savonius vertical axis wind turbine for vehicle is necessary. The research is conducted numerically using MATLAB software. The wind speed, Reynolds number, and electric power output are numerically simulated to obtain the swept area design. Innovative …

New Design Of Aluminum 6061 Welding Joining Using Friction Stir Welding Method, Widia Setiawan, Nugroho Santoso, Surojo Surojo

Journal of Mechanical Engineering Science and Technology (JMEST)

Parallel, lap, corner, and T joints are commonly used in fusion welding and solid welding. Other joints made are lap and butt joint. This study aims to evaluate a new design of fitting model single U and double U for friction stirr welding of Aluminum. Aluminum sheet 6061with a thickness of 10 mm, will be cut to a length of 150 mm and a width of 100 mm, then a locking groove will be made with an inner size of 5 mm and a length of 150 mm The flow is used to be paired in the FSW process. This …

Tool Life Prediction Of Ti [C,N] Mixed Alumina Ceramic Cutting Tool Using Gradient Descent Algorithm On Machining Martensitic Stainless Steel, Joseph Daniel S, Senthil Kumar A

Journal of Mechanical Engineering Science and Technology (JMEST)

In automated manufacturing systems, most of the manufacturing processes, including machining, are automated. Automatic tool change is one of the important parameters for reducing manufacturing lead time. Machining studies on Martensitic Stainless Steel was conducted using Ti[C,N] mixed alumina ceramic cutting tool. Tool life was evaluated using flank wear criterion. The tool life obtained from experimental machining process was taken as training dataset and test dataset for machine learning. Tool life model was developed using Gradient Descent Algorithm. The accuracy of the machine learning model was tested using the test data, and 99.83% accuracy was obtained.