Mechanical Engineering Commons^™

Effective Modulus Of Cracked Bodies: A Finite Element Analysis, Alan Thomas Varughese

Theses and Dissertations--Mechanical and Aerospace Engineering

This thesis considers how cracks in an elastic body can alter the body’s elastic properties. In the present study the elastic property of note is the elastic or young’s modulus. It is desired to investigate to what extent the number and orientation of cracks can cause a reduction in the elastic modulus. Because of the complex nature of the elastic fields resulting from multiple cracks interacting together in a finite geometry an analytical solution is not possible or considered. Rather the Finite Element Method is used to determine the elastic response to a body with many cracks. This provides a …

Structural Optimization Of Space Transit Vehicle Concept, Hercules, James Philip Rogers

Theses and Dissertations--Mechanical and Aerospace Engineering

STRUCTURAL OPTIMIZATION OF SPACE TRANSIT VEHICLE CONCEPT, HERCULES:

A COMPARATIVE STUDY OF STRUCTURAL OPTIONS

Hercules is a vehicle concept developed by NASA Langley's Vehicle Analysis Branch to satisfy the need for sustainable transit between Earth, the moon, and Mars. Hercules features unprecedented abort capabilities and mission flexibility to aid in NASA's Mars campaign. By utilizing modern software to perform structural analysis and optimization for a large selection of stiffened panel concepts, beam concepts, and materials trends in the structural optimization emerge. These trends will be invaluable for the design of future spacecraft needed to fulfill similar roles.

The structural optimization …

Electromagnetic Formation Control Using Frequency Multiplexing, Zahra Abbasi

Theses and Dissertations--Mechanical and Aerospace Engineering

This dissertation addresses control of relative positions and orientations of formation flying satellites using magnetic interactions. Electromagnetic formation flight (EMFF) is implemented, in which each satellite is equipped with a set of electromagnetic coils to generate an electromagnetic field. Traditional EMFF technique applies DC magnetic fields which lead to a nonlinear and highly coupled formation dynamics that allow for only position or orientation control of the satellites. We present a new frequency multiplexing method, which is a technique that uses multi-frequency sinusoidal controls, to approximately decouple the formation dynamics and to provide enough controls for both position and orientation control. …

Additive Manufacturing In Personalized Medicine: Patient-Customized Solid Dose Medicines, And Patient-Customized Wound Care Device, Amir Najarzadeh

Theses and Dissertations--Mechanical and Aerospace Engineering

Personalized Medicine - from a one-size fits all to a tailored approach is the future in pharmaceutical therapeutics and medical applications. The aim of this study is demonstrate additive manufacturing in two personalized medicine applications: 1. Patient- customized solid dose medicines, and 2. Patient-customized wound care device. The aim of the first application is to develop an inexpensive and accurate method to design and fabricate patient-customized tablets. Particularly this paper focuses on fabricating and dose controlling of patient-customized extended release prednisolone-poly(vinyle alcohole) PVA. Dry-Blending, Wet Granulation, Extrusion, Spherionization, Hot melt extrusion (HME) was adopted to produce drug loaded prednisolone-PVA filaments …

Wind Turbine Main Bearing Fatigue Prognosis With Physics-Informed Machine Learning, Yigit Yucesan

Electronic Theses and Dissertations, 2020-2023

Unexpected main bearing failure on a wind turbine causes unscheduled maintenance and increased operation costs (mainly due to crane, parts, labor, and production loss). Unfortunately, historical data indicates that failure can happen far earlier than the component designed lives (due to manufacturing problems, for example). For the legacy fleet, which composes the majority of the installed basis, fatigue has become a major issue. Although bearing fatigue can be expressed with physics-informed models, they often inherent large uncertainties due to operation and unknown lubricant degradation mechanism. Apart from the unknown physics of failure, additional uncertainties associated with the grease that surrounds …

Econometric Frameworks For Energy Prediction, Naveen Chandra Iraganaboina

Electronic Theses and Dissertations, 2020-2023

Global warming and associated role of energy consumption across various sectors is a well-researched topic in recent years. Understanding current urban energy consumption patterns will allow us to understand how future energy consumption patterns will evolve. With electrification of vehicles and potentially altering culture of work from home, the energy usage at regional level would see a significant change in the future. The current PhD dissertation contributes to energy consumption analysis of a region by analyzing residential energy consumption, commercial energy consumption and transportation energy use by households. The aggregation of these energy consumption within a region contributes to the …

Novel New Modeling Procedure For Industrial Machinery With Nonlinear Connections, Steven Whitican

Dissertations, Master's Theses and Master's Reports

Given current timelines for rolling out production at volume, the ability to model portions of the production process is of paramount importance. To model production, high-fidelity models of production assets must be obtained. The production assets are comprised of linear and nonlinear structures. The linear structures are well understood and defined. Significant work has, and is, being done to understand the nonlinear components. This work focuses on developing and correlating a model of a nonlinear component. The component studied and modeled is a linear guide. Linear guides are bearings which facilitate translational motion of machine axes. An accurate model of …

Test 2237: John Deere 8rx 340, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2245: Fendt 1156 Vario Mt, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2244: Fendt 1151 Vario Mt, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2239: Kubota M8-211, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Tensile Environment Chamber, Cameron Ngai, Trent Hamilton, Mitchell Carroll, Jack Molitor

Mechanical Engineering

This project created the heating system, cooling system, and control system for an environmental chamber for a tensile test machine in the Cal Poly Composites Lab. This chamber allows for students to test material properties under a variety of thermal conditions. This project was done in collaboration with a team working on the structural aspect of the chamber. While consumer environmental chambers are on the market, they often cost more than $50,000. Additionally, our chamber conforms to further size and weight constraints. Because of this constraint, many conventional techniques and components used for these chambers are not feasible for our …

Dual Motor Drive System For Formula Sae Electric Race Car, Bryan D. Neill, Jackson T. Mcfaul, Cole T. Andrews, Isaiah D. Penzell

Mechanical Engineering

This paper serves as the Final Design Report (FDR) for the senior project developed by our team. This FDR builds on our CDR, in which the main deliverable was the detailed design of a planetary gearbox delivering a 5:1 reduction to be mated to an Emrax 188 motor. This planetary gearbox would allow for the possibility of implementing a dual-motor torque-vectoring rear-wheel-drive system in Cal Poly Racing’s electric FSAE car, which has demonstrated in simulation to yield significant performance gain over the current single motor/mechanical LSD system. As this project’s scope is purely mechanical, the intent is for the Cal …

Quality Assurance Of Lightweight Structures Via Phase-Based Motion Estimation, Ikenna E. Ifekaonwu

College of Graduate Studies: Theses & Dissertations

In recent years, lightweight structures have become mature and adopted in various applications. The importance of quality assurance cannot be overemphasized hence extensive research has been conducted to assess the quality of lightweight structures. This study investigates a novel process that exploits motion magnification to investigate the damage characteristics of lightweight mission-critical parts. The goal is to assure the structural integrity of 3D printed structures and composite structures by determining the inherent defects present in the part by exploiting their vibration characteristics. The minuscule vibration of the structure was recorded with the aid of a high-speed digital camera, and the …

Signals As Symbols: Applying Normalization Of Deviance To Improve User-Centered Design, Amy Vanschaik

Electronic Theses and Dissertations, 2020-2023

Mistakes can happen in the process of designing and developing interactive digital projects. Sometimes these mistakes negatively impact users' perception and trust of digital interfaces. This research applies the concept of normalization of deviance to identify potential missed opportunities in user-centered design data within the context of a website redesign. By doing this I explore how through observing accidental deviant behaviors or processes we can identify ways to improve the usability and user experience of digital environments. I review the concepts of normalized deviant behavior as addressed by Diane Vaughan in the field of engineering and identify a process for …

Using Smart-Wifi Thermostat Data To Improve Prediction Of Residential Energy Consumption And Estimation Of Savings, Abdulrahman Alanezi, Kevin P. Hallinan, Rodwan Elhashmi

Mechanical and Aerospace Engineering Faculty Publications

Energy savings based upon use of smart WiFi thermostats ranging from 10 to 15% have been documented, as new features such as geofencing have been added. Here, a new benefit of smart WiFi thermostats is identified and investigated; namely, as a tool to improve the estimation accuracy of residential energy consumption and, as a result, estimation of energy savings from energy system upgrades, when only monthly energy consumption is metered. This is made possible from the higher sampling frequency of smart WiFi thermostats. In this study, collected smart WiFi data are combined with outdoor temperature data and known residential geometrical …

Studies On Powder Compaction And Wire Extrusion Of Pure Metals And Metal/Cnt Nano Composites, Qiang Zhou

Electronic Theses and Dissertations, 2020-2023

The goal of this dissertation is to fabricate wires made of Cu/CNT and Al/CNT composites with good mechanical strength and super thermal/electrical conductivities using powder compaction and wire extrusion manufacturing processes. Powder compaction was studied using both test and simulation. Cold compaction, hot compaction and vibration assisted (cold) compaction tests were conducted to achieve different density ratios. Hot compaction tests improved about 6% compared with cold compaction under the same compression pressure. Although the relative density ratio does not obviously improve at vibration assisted (cold) compaction, the strength of the specimens made under vibration loading is much better than those …

An Evaporation Based Micro-Synthetic Jet In Microchannel And Its Applications, Ehsan Sourtiji

Electronic Theses and Dissertations, 2020-2023

An approach to create synthetic jets at micro-scales using periodic bubble growth and collapse was presented and studied over a range of operating frequencies (0.1 to 2.5 Hz) and heating powers (3 to 4.5 Watt). The microfluidic device uses an interfacial layer between vapor and liquid phases which substitutes the requirement for a physical flexible membrane and any other moving parts. The bubble explosion and implosion in the chamber was triggered by periodically powering a micro-heater, which in turn generated the synthetic jet. High-speed camera photography and a microscope were used to capture sequential images of bubble nucleation, growth and …

Identification Of Neuromarkers Using Structural And Functional Neuroimaging, Sreevalsan Sanathanan Menon

Doctoral Dissertations

"One of the grand challenges in science is understanding the human brain. Recent advances in magnetic resonance imaging have opened unmatched opportunities to demystify neural circuitry. In this research, the spatially and temporally complex neuroimaging data were used to identify neuromarkers that aids in quantifying a brain’s health. In the first part, a comparison of static and dynamic functional connectivities was made to study their efficacies in identifying intrinsic individual connectivity patterns. Results show that the intrinsic individual connectivity pattern can be used as a ‘fingerprint’ to distinguish among and identify subjects and their biological sex and is more accurately …

Investigation Of The Sensitivity Of Human Arm To Small Interaction Forces During Physical Human-Robot Interaction (Phri), Fazlur Rashid

Masters Theses

“Understanding the human motor control strategy during physical interaction tasks is crucial for developing future robots for physical human-robot interaction (pHRI). Effective pHRI depends on humans communicating their intentions for movement with robots. In physical human-human interaction (pHHI), small interaction forces are known to convey their intent between the partners. It is speculated that small interaction forces contain significant information to convey the movement intention of pHHI. However, the mechanism underlying this interaction strategy is largely unknown. Hence, the aim of this work was to investigate what affects humans’ sensitivity to the interaction forces. The hypothesis was that small interaction …

Fabrication Of Silicon Nitride Parts By Ceramic On-Demand Extrusion Process, Sachin Choudhary

Masters Theses

“Ceramic On-Demand Extrusion (CODE) is a patented solid freeform fabrication method for manufacturing high-density monolithic ceramic parts. In the past 5-6 years, the technology has been successfully implemented to fabricate alumina and zirconia parts. The mechanical characterizations also show CODE’s high potential in achieving desired structural properties. The present study covers the fabrication of silicon nitride parts by CODE process, which entailed the design of paste formulation for achieving rheology suitable for dimensional control in fabricated parts and determining firing temperature and the content of sintering additives for silicon nitride green bodies fabricated by CODE. The density, hardness, and fracture …

Research And Development Of A Laser Hot Wire Deposition Process, Christopher Croft

Masters Theses

“Laser hot wire directed energy deposition (DED) is an increasingly popular method for improving deposition rates and overall reduction of build times in DED processing. While there is clear benefit, it is important to fully understand the impact of preheating the wire. This work focuses on developing a model that describes bead geometry output using all factors including the wire preheat. The model was fit with over 150 data points that explored a large range of each factor. The resulting model was then leveraged to evaluate a process control variable. The technique chosen used feedback from the hot wire system …

Physics-Based Modeling Of Lithium-Ion Batteries For Control And Estimation Applications, Brody J. C. Riemann

Masters Theses

“Lithium-ion batteries are extensively used in many application areas like consumer electronics, electric vehicles, and microgrids. As the world moves towards further electrification of vehicles and more widespread use of renewable energy sources, the need for large-scale battery storage systems will grow. To effectively replace conventional methods, batteries will need to be charged quickly while accounting for degradation to maximize lifetime. Further, larger batteries require more detailed safety monitoring, which is implemented using a battery management system (BMS). A BMS is responsible for state of charge (SOC) estimation, state of health (SOH) estimation, cell balancing, regulating voltage and current according …

Theoretical Study Of Magnetic Particles In A Shear Flow Subjected To A Uniform Magnetic Field, Christopher A. Sobecki

Doctoral Dissertations

"Magnetic manipulation of non-spherical magnetic microparticles is important for applications in shape-based and magnetic-based separations such as waste management, disease diagnostics, drug delivery, and mining. Manipulations of magnetic microparticles also include chain formation to assemble compositions for electronics, drug loading designs, and magnetorheological fluids for smart armor, hydraulic brakes, and dampers. In microfluidic devices, separation-formation-effectiveness depends on the shape of the channel, the shear rate, and the magnetic field strength and direction.

Particle separation and chain formation involved highly complex and computational expense-demanding studies in microfluidic devices, magnetic fields, and particle- particle/wall interactions. This research took complex experimental studies and …

Transient Maneuvers And Pressure Analysis On An Automotive Torque Converter, Abigail A. Hempy

Dissertations, Master's Theses and Master's Reports

This work involves an investigation of internal fluid behavior of an automotive torque converter in a front-wheel drive automatic 6-speed transmission. The fluid behavior is identified through 29 pressure transducers instrumented throughout the torus, acquired through IR Telemetrics multiplexed channels, and analyzed with custom MATLAB code. The main vehicle operating conditions studied in this research are back drive scenarios or low motoring torques. Findings showed speed and torque limits for open converter coast down conditions as well as pressure field behavior with negative input torque.

Development Of The Carbon Nanotube Thermoacoustic Loudspeaker, Troy Bouman

Dissertations, Master's Theses and Master's Reports

Traditional speakers make sound by attaching a coil to a cone and moving that coil back and forth in a magnetic field (aka moving coil loudspeakers). The physics behind how to generate sound via this velocity boundary condition has largely been unchanged for over a hundred years. Interestingly, around the time moving coil loudspeakers were first investigated the idea of using heat to generate sound was also known. These thermoacoustic speakers heat and cool a thin material at acoustic frequencies to generate the pressure wave (i.e. they use a thermal boundary condition). Unfortunately, when the thermoacoustic principle was initially discovered …

Design And Testing Of An Open Source Vacuum Oven For Research, Community Recycling, And Additive Manufacturing, Benjamin R. Hubbard

Dissertations, Master's Theses and Master's Reports

To aid the continuing growth of open source tools in the research community, this thesis presents two broadly useful instruments which can be built and operated for a fraction of the cost of equivalent or inferior commercial products. The first device is a digitally-replicable scale, which provides a single framework for making measurements on the order of milligrams all the way up to tens of kilograms by supporting multiple types of load cells. The second device is a vacuum oven, which is validated using the first. The open source vacuum oven facilitates the dehydration of materials at low temperature, providing …

Towards Systems On Cloth: The Design, Manufacturing, And Validation Of Open-Source Embroidered Resistors, Somerset Schrock

Dissertations, Master's Theses and Master's Reports

This thesis is focused on advancing embroidered wearable electronics and textile electronics by creating open-source flexible resistors. Advancements in textile electronics could usher a new generation of smart devices that are entirely flexible. Current systems on cloth primarily use rigid components, which limits the flexibility and comfort of using the fabric devices. To advance this field, I propose a novel method of creating flexible electrical resistors with embroidery. To realize this technology, I created an open-source tool to create embroidery files for machine fabrication. This thesis details the methods and tools created for resistor fabrication. The resistors were tested to …

Multiscale Investigation Of Dropwise Condensation On A Smooth Hydrophilic Surface, Shahab Bayani Ahangar

Dissertations, Master's Theses and Master's Reports

The objective of this work is to identify the fundamental mechanism of dropwise condensation on a smooth solid surface by probing the solid-vapor interface during phase-change to evaluate the existence and structure of the thin film and the initial nucleus that develop during condensation. In this work, an automated Surface Plasmon Resonance imaging (SPRi) instrument with the ability to perform imaging in intensity modulation and angular modulation is developed. The SPRi instrument is used to probe (in three dimensions) the adsorbed film that forms on the substrate during dropwise condensation. SPRi with a lateral resolution of ~ 4-10 μm, thickness …

Marangoni Propulsion Of Active Particles, Saeed Jafari Kang

Dissertations, Master's Theses and Master's Reports

We study the surfing motion of active particles located at a flat liquid-gas interface. The particles create and maintain a surface tension gradient by asymmetrically discharging a surface tension-reducing agent. We employ theory and numerical simulation to investigate the Marangoni propulsion of these active surfers. First, we use the reciprocal theorem to establish a relationship between the propulsion speed and the release of the active chemical. This theoretical relation is utilized to examine the effect of wall confinement and geometry on the Marangoni-driven motion of active particle when the inertial effects are negligible and when the transports of the released …