Mechanical Engineering Commons^™

A Novel Drive Cycle Simulation Model For Gasoline Engines To Investigate Bandwidth Coverage Of Emission Performance And Fuel Consumption With Engine Control Parameters, Martin Giencke

Doctoral

The presented work is offering an investigation how the bandwidth of vehicle specific attributes is impacting engine control parameter requirements for warmup control of the catalytic converter, aiming to ease the development process by providing mathematical means for an automatic generation of control settings. For the specific purpose, a novel drive cycle simulation approach is developed, focusing on emission performance and fuel consumption of a gasoline engine. Steady state and quasi steady state measurements are collected to quantify the impact of modifications to control parameters on emission concentration, exhaust gas temperature and engine torque, especially directly after a cold start. …

Experimental Investigation And Prediction Of Long-Term Effect Of Sustained Load And Harsh Environment On Fiber-Reinforced Polymer Composites, Amir Hussain Idrisi

Dissertations

In this dissertation the durability of thermoset composites was investigated under sustained load. Two thermoset composites, E-glass/epoxy and E-glass/polyurethane were immersed in seawater under sustained load (10%, 15%, 20%, 25% of failure load) and varying temperature (23°C to 95°C) for the period of 15 months. Mechanical, physical and thermal properties were experimentally investigated. The effects of temperature, moisture, and immersion time on the deterioration of the composite material were studied for both composites. It was observed that the weight of the samples increased with the immersion time and temperature for both the composites. The highest increase in weight of the …

Reliable Mode Tracking In Gradient-Based Optimization Frameworks With Flutter Constraints, Taylor Mcdonnell, Andrew Ning

Faculty Publications

In order to construct mode-specific flutter constraints for use in gradient-based multidisciplinary design optimization frameworks, mode tracking must be used to associate the current iteration’s modes with the modes corresponding to each constraint function. Existing mode tracking methods, however, do not provide a method by which to ensure the accuracy of mode associations, making them unsuitable for use in situations where obtaining correct mode associations is critical. To remedy this issue, a new mode tracking method is presented which incorporates backtracking logic in order to maintain an arbitrarily high degree of confidence in mode correlations during gradient-based optimization and/or during …

Implementing A Data Acquisition System For The Training Of Cloud Coverage Neural Networks, Weston C. Montgomery

Master's Theses

Cal Poly is home to a solar farm designed to nominally generate 4.5 MW of electricity. The Gold Tree Solar Farm (GTSF) is currently the largest photovoltaic array in the California State University (CSU) system, and it was claimed to be able to produce approximately 11 GWh per year. These types of projections come from power generation models which have been developed to predict power production of these large solar fields. However, when it comes to near-term forecasting of power generation with variable sources such as wind and solar, there is definitely room for improvement.

The two primary factors that …

The Application Of Post-Hoc Correction Methods For Soft Tissue Artifact And Marker Misplacement In Youth Gait Knee Kinematics, Kaila L. Lawson

Master's Theses

Biomechanics research investigating the knee kinematics of youth participants is very limited. The most accurate method of measuring knee kinematics utilizes invasive procedures such as bone pins. However, various experimental techniques have improved the accuracy of gait kinematic analyses using minimally invasive methods. In this study, gait trials were conducted with two participants between the ages of 11 and 13 to obtain the knee flexion-extension (FE), adduction-abduction (AA) and internal-external (IE) rotation angles of the right knee. The objectives of this study were to (1) conduct pilot experiments with youth participants to test whether any adjustments were necessary in the …

Prediction Of In-Plane Stiffnesses And Thermomechanical Stresses In Cylindrical Composite Cross-Sections, Bryson M. Chan

Master's Theses

Accurate mechanical analysis of composite structures is necessary for the prediction of laminate behavior. Cylindrical composite tubes are a mainstay in many structural applications. The fundamental design of circular composite cross-sections necessitates the development of a comprehensive composite lamination theory. A new analytical method is developed to characterize the behavior of thin-walled composite cylindrical tubes using a modified plate theory. A generated numerical solver can predict properties such as axial stiffness, bending stiffness, layer stresses, and layer strains in composite tubes subjected to combined mechanical loading and thermal effects. The model accounts for the curvature by transforming and translating the …

Analytical, Numerical, And Computational Methods To Analyze The Time To Empty Open, Closed, And Variable-Topped Inverted Bottles, Callen Schwefler

Master's Theses

Recent unexpected experimental observations of the emptying of inverted bottles with perforations has generated interest in modeling and simulation of this phenomenon. It was observed that as a perforation, i.e., a small hole at the "top" of the inverted bottle, is added and enlarged, the overall emptying time first increases to a maximum value and then decreases until it reaches a lower limit. The change in emptying time is associated with a transition from jetting, where only water exits the neck, to glugging, a competition between air and water flows at the neck of the bottle.

This paper develops analytical …

Bi-Directional Kerr-Lens Mode-Locked Titanium Sapphire Laser, Ricky Arnold, Stratos Koutroulis, Dylan Meyer

Mechanical Engineering Senior Theses

Precision near-infrared absorption spectroscopy is a highly desired scientific method, but the blooming technology has not yet come to fruition. Field deployments are limited, and some methods come with limitations that hamper the viability. The laser cavity completed for this thesis project is a single cavity Dual Comb Spectroscopy laser, which improves myriad limiting characteristics of previous lasers in this application. Crucially, it can produce two simultaneous pulse trains with unique repetition rates. The laser cavity has been designed, built, and aligned for improved stability, including vibrational, noise, and thermal control. The design, analysis, and results of a dual comb …

Electric Field Induced Self-Assembly Of Mesoscale Structured Materials And Smart Fluids, Suchandra Das

Dissertations

This dissertation aims to study the forces that drive self-assembly in binary mixtures of particles suspended in liquids and on fluid-liquid interfaces when they are subjected to a uniform electric or magnetic field. Three fluid-particle systems are investigated experimentally and theoretically : (i) Suspensions of dielectric particles in dielectric liquids; (ii) Suspensions of ferromagnetic and diamagnetic particles in ferrofluids; and (iii) Dielectric particles on dielectric fluid-liquid interfaces. The results of these studies are then used to estimate the parameter values needed to assemble materials with desired mesoscale microstructures.

The first fluid-particle system studied is an electrorheological (ER) fluid formed using …

Service Quality Assessment And Improvement Methods And Tools, Kevin M. Moriarty

Dissertations

The nucleus of this research concept and system is being applied to turret lathe and milling machine Computer Numerical Control (CNC) tool systems. The research has a generic application to the service of broad array of sophisticated computer controlled / integrated machines, devices / equipment such as industrial robotics, medical equipment, surgical robots, and similar types of engineered system. Quality design review for quality service systems is a unique concept. Standard product service systems are qualitative and subjective in nature. The quantitative system identifies Key Predictive Attributes (KPAs) and applies quantitative methods to these attributes to develop a systematic process …

Private Sound Environments In Public Space: Use Of Headphones In Public Parks And Public Transit, Chathurthi S. De Silva

Dissertations

The use of headphones is now so commonplace that it is almost second nature for many people to use them. Not only do these people use headphones all the time, but they use them nearly everywhere, including in urban public spaces. In using headphones, people create their own “private sound environments” in public space. This phenomenon merits attention from researchers since the creation of private sound environments may well alter people’s experiences of public space.

This study answers five research questions about the use of headphones in parks and on transit: why people use them, when they begin using headphones …

Investigation Of Topological Phonons In Discrete Mechanical Metamaterials, Kai Qian

Dissertations

The study of topological mechanical metamaterials is a new emerging field that focuses on the topological properties of artificial mechanical structures. Inspired by topological insulators, topological mechanism has attracted intensive attention in condensed matter physics and successfully connected the quantum mechanical descriptions of electrons with the classical descriptions of phonons. It has led to experiments of mechanical metamaterials possessing topological characteristics, such as topologically protected conducting edges or surfaces without back-scattering. This dissertation presents a new experimental approach for mechanically engineering topological metamaterials based on patterning magnetically coupled spinners in order to localize the propagation of vibrations and evaluate different …

Investigation Of Two-Phase Flow Phenomena In Rotating Paper Dryer To Achieve Effective Heat Transfer With Low Energy Consumption, Hamed Abdul Majeed

LSU New Orleans Theses and Dissertations

The paper industry provides important consumer products comprised of paper, tissue, paper board, and pulping. The papermaking process requires a lot of energy, in the form of steam, to dry the paper web in rotating dryers. As steam condenses inside the dryers by releasing heat to the dryer walls, the condensate is removed using either stationary or rotary siphons. Since the condensate is usually at a saturated state, part of the condensate flashes into vapor during the extraction process and becomes difficult to extract. Thus, additional blow-through steam is used to push the condensate out. Since this blow-through steam is …

Numerical Study On Oscillating Flow Over A Flat Plate Using Pseudo-Compressibility In Intermittent Turbulent Regime, Shivank Srivastava Mr.

LSU New Orleans Theses and Dissertations

A Computational Fluid Dynamic (CFD) in-house code is developed to study unsteady characteristics of incompressible oscillating boundary layer flow over a flat plate under laminar and intermittently turbulent condition using pseudo-compressible unsteady Reynolds Averaged Navier- Stokes (RANS) model. In the in-house code, the two-dimensional, unsteady conservation of mass and momentum equations are discretized using finite difference techniques which employs second order accurate (based on Taylor series) central differencing for spatial derivatives and second order Runge-Kutta accurate differencing for temporal derivatives. The in-house code employs Fully Explicit-Finite Difference technique (FEFD) to solve the governing differential equations of the mathematical model. In …

Mitigation Of Airborne Contaminant Spread Through Simple Interventions In An Occupied Single-Family Home, Florida Solar Energy Center, Nazim Muradov

FSEC Energy Research Center®

Historically, reducing aerosol-based transmission of respired viruses in indoor environments has been of importance for controlling influenza viruses and common-cold rhinoviruses. The present public health emergency associated with SARS-CoV-2 makes this topic critically important. Yet to be tested is the potential effectiveness of simple interventions that create an isolation zone (IZ) for a suspected/confirmed sick or sensitive person requiring quarantine. The intent in existing homes is to find a practical means to mitigate exposure to airborne contaminants. In creating an IZ in an occupied single-family home in the study, four simple strategies were tested. The test configurations were: (1) IZ …

Wildfire Prevention & Suppression System, Johnny Dimas Flores, Ansh Jetly, Antonio Lorenzo

Mechanical Engineering Senior Theses

The Bay area community has continually been at threat to wildfires. The current trend showed that wildfires would be an even more prevalent threat in the near future. Despite this, there still exists a lack of knowledge involving wildfire safety and protection for people’s property. Current systems were found to be too expensive, needed constant maintenance, or access to isolated storage of 1,000+ gallons of water. Through research of misting systems, the effectiveness of mist as a radiation shield, and working with members of CalFire, it was determined that the system needed to meet the following parameters to be effective …

Uavs For Vegetation Monitoring: Overview And Recent Scientific Contributions, Ana I. De Castro, Yeyin Shi, Joe Mari Maja, Jose M. Pena

Department of Mechanical and Materials Engineering: Faculty Publications

This paper reviewed a set of twenty-one original and innovative papers included in a special issue on UAVs for vegetation monitoring, which proposed new methods and techniques applied to diverse agricultural and forestry scenarios. Three general categories were considered: (1) sensors and vegetation indices used, (2) technological goals pursued, and (3) agroforestry applications. Some investigations focused on issues related to UAV flight operations, spatial resolution requirements, and computation and data analytics, while others studied the ability of UAVs for characterizing relevant vegetation features (mainly canopy cover and crop height) or for detecting different plant/crop stressors, such as nutrient content/deficiencies, water …

Three-Dimensional Shape Analysis Of Peripapillary Retinal Pigment Epithelium-Basement Membrane Layer Based On Oct Radial Images, Junfei Tong, Pengfei Dong, Sachin Kedar, Deepta Ghate, Linxia Gu

Department of Mechanical and Materials Engineering: Faculty Publications

The peripapillary retinal pigment epithelium-basement membrane (ppRPE/BM) layer angle was recently proposed as a potential index for estimating intracranial pressure noninvasively. However, the ppRPE/BM layer angle, measured from the optical coherence tomography (OCT) scans, varied across the radial directions of the optic disc. This made the ppRPE/BM layer angle difficult to be utilized in its full potential. In this study, we developed a mathematical model to quantify the ppRPE/BM layer angles across radial scans in relation to the ppRPE/BM 3D morphology in terms of its 3D angle and scanning tilt angles. Results showed that the variations of the ppRPE/BM layer …

A Self-Tunable Piezoelectric Energy Harvester, Ashraf Hussein

Theses and Dissertations

In this study, a new technique to harvest energy using inertial vibration energy harvesters is introduced. A triple-layer piezoelectric beam with a self-tunable frequency was developed in order to respond to variable-frequency excitations, thereby maintaining the beam in a state of resonance for maximum power output. The tuning mechanism managed to change the natural frequency of the beam in the range of 2.27 ���� to 6.25 ����. In this case, the output voltage could be raised from 12�� to 23��.

A mathematical model was developed to investigate the natural frequency, the output voltage, and the output power of the beam …

Frequency Domain Measurements Of Melt Pool Recoil Force Using Modal Analysis, Tristan Cullom, Cody Lough, Nicholas Altese, Douglas Bristow, Robert Landers, Ben Brown, Troy Hartwig, Andrew Barnard, Jason Blough, Kevin Johnson, Edward Kinzel

Michigan Tech Publications, Part 1

Recoil pressure is a critical factor affecting the melt pool dynamics during Laser Powder Bed Fusion (LPBF) processes. Recoil pressure depresses the melt pool. When the recoil pressure is low, thermal conduction and capillary forces may be inadequate to provide proper fusion between layers. However, excessive recoil pressure can produce a keyhole inside the melt pool, which is associated with gas porosity. Direct recoil pressure measurements are challenging because it is localized over an area proportionate to the laser spot size producing a force in the mN range. This paper reports a vibration-based approach to quantify the recoil force exerted …

Comparison Of Fish Assemblages Aggregated By Artificial Reefs Using Scuba Diving And Acoustic Surveys, Hsueh-Jung Lu, Jia-Rong Lin, Ting-Chieh Huang, Sunarti Sinaga

Journal of Marine Science and Technology–Taiwan

To determine the aggregation effect of artificial reefs (ARs), we conducted surveys in 16 artificial reefs in Taiwan by using the scientific echo sounder, Simrad EY-60 (200 KHz), along with sighting by scuba divers. Scuba diving was conducted within the reef structures (r ¼ 20 m), whereas acoustic surveys were conducted over a wider range (r ¼ 100 m), with five repeating transects over the ARs. We compared the results obtained from the two methods among 16 artificial reefs in the coastal waters of Taiwan to determine the consistency of the quantitative information between the two methods and to investigate …

Study On The Behavior Of Peled (Coregonus Peled ) Around A Set Net By Ultrasonic Biotelemetry System In A Plateau Lake, China, Jing Liu, Keiichi Uchida, Leiming Yin, Yong Tang, Yoshinori Miyamoto, Binbin Xing

Journal of Marine Science and Technology–Taiwan

Sayram Lake is a plateau cold-water lake located in northwestern China. Peled (Coregonus peled ) was introduced to Sayram Lake from Russia in 1998. The behavior characteristics of peled in Sayram Lake are important for fishery resource proliferation, effective fishing, and sustainable development. In this study, we used an ultrasonic biotelemetry system to track the fish around a large-scale set net in Sayram Lake. The purpose of this study is to study the behavior characteristics of the peled and to provide suggestions for the improvement of the set net. The results showed that the fish released in the playground of …

Energy-Based Orbital Stabilization Of Underactuated Systems Using Impulse Controlled Poincaré Maps, Nilay Kant, Ranjan Mukherjee

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The problem of energy-based orbital stabilization of underactuated mechanical systems with one passive degree-of-freedom is addressed. The orbit is a manifold where the active generalized coordinates are fixed, and the total mechanical energy is equal to some desired value. A hybrid control strategy comprised of continuous and intermittent impulsive inputs is presented. The continuous controller is designed using partial feedback inearization to converge the active generalized coordinates to their desired values. The choice of desired energy characterizes a unique orbit which is stable but not asymptotically stable. To stabilize the desired orbit, a Poincaré section is constructed at a fixed …

Mash 2016 Test Level 3 And Test Level 4 Evaluation Of Roadside Safety Barrier With Pedestrian Features, Miguel Angel Hinojosa Palacios

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

The Minnesota Department of Transportation (MnDOT) desires to use a vehicle, bicycle, and pedestrian combination bridge railing system along pedestrian and bicycle bridge paths. The system was evaluated per MASH 2016.

In full-scale crash test no. MNPD-3, the system was evaluated according to MASH test designation no. 3-11. The 2014 Dodge Ram 1500 crew cab pickup truck impacted the system 71¼ in. upstream from the centerline of post no. 4 with a speed of 63.4 mph at an angle of 25.3 degrees. The combination railing system was found to meet the AASHTO MASH 2016 TL-3 impact safety criteria.

MnDOT uses …

Effects Of Air Pollution, Temperature And Moisture Content On Copper And Silver Corrosions And The Reliability Of Data Center Equipment, Rui Zhang

Dissertations - ALL

The effects of moisture content, temperature, and pollutant mixture on atmospheric corrosion of copper and silver were investigated by exposing test specimens to different environmental conditions, followed by surface characterization using the coulometric reduction, Scanning Electron Microscopy, and Energy Dispersive Spectrometry (SEM/EDS). Printed circuit board test cards (PCBs) with bare copper were also used to investigate the effects of voltage bias on the PCBs on the corrosion rate. The test specimens were exposed to mixed flowing gases (MFG) environment with eight different combinations of the following five pollutants at the fixed concentration levels: 60 ppb O3, 80 ppb NO2, 40 …

An Intelligent Virtual Design Studio (Vds) For Integrative Design Of Green Buildings, Zhaozhou Meng

Dissertations - ALL

The overall goal of the study was to develop a "Virtual Design Studio (VDS)": a software platform for integrated, coordinated and optimized design of green building systems with low energy consumption, high indoor environmental quality (IEQ), and high level of sustainability. My dissertation research was focused on the development of a key VDS component -- an integrated design process and a near-real time performance simulation approach for fast feedbacks at the early stage of the integrated design process.

A design process module "Magic Cube" (MC) was developed for the VDS as the core for the design integration and coordination. It …

Seasonal Dynamics In Fish Distribution And Abundance Revealed By An Acoustic Survey In Coastal Waters Of The Suzu Area, Kochi Prefecture, Japan, Yanhui Zhu, Kenji Minami, Yuka Iwahara, Kentaro Oda, Koichi Hidaka, Osamu Hoson, Koji Morishita, Sentaro Tsuru, Masahito Hirota, Hokuto Shirakawa, Kazushi Miyashita

Journal of Marine Science and Technology–Taiwan

For Japan's fishery, it is essential to conduct sustainable and efficient fishery owing to the decline in fish catch as well as the fisher population. To obtain information that contributes to sustainable and efficient fishery, we researched appropriate set-net locations with regard to fish distribution, abundance, and environmental characteristics. We conducted surveys from 2017/5 to 2018/2 in the Suzu coastal area, Kochi Prefecture, where the only main industry is set-net fishery. We investigated the seasonal relationships between fish school characteristics, including distribution and size, and marine environmental conditions in the Suzu coastal area, using a quantitative echo sounder (KSE300 SONIC, …

Development Of A Biomass Assessment Method Using Fisheries Echo Sounder For Monitoring Whitebait Fishery In Shizuoka Prefecture, Japan, Kenichi Kobayashi, Yanhui Zhu, Daichi Oshiyama, Kenji Minami, Hokuto Shirakawa, Kazushi Miyashita

Journal of Marine Science and Technology–Taiwan

Coastal fisheries constitute the second most important sector in fishery production in Japan, following offshore fisheries. Thus, spatial evaluation of coastal fishing grounds and understanding of the changes in biomass are important for the sustainable use of fishing resources. For the assessment of spatial fish biomass, a quantitative echo sounder is used, but such a device is not mass produced and involves a high cost. In the present study, we examined the feasibility of biomass assessment using typical commercial fisheries echo sounders that are widely used and cheaper than quantitative echo sounders. Therefore, we aimed to verify the validity of …

An Intelligent Virtual Design Studio (Vds) For Integrative Design Of Green Buildings, Zhaozhou Meng

Dissertations - ALL

The overall goal of the study was to develop a “Virtual Design Studio (VDS)”: a software platform for integrated, coordinated and optimized design of green building systems with low energy consumption, high indoor environmental quality (IEQ), and high level of sustainability. My dissertation research was focused on the development of a key VDS component -- an integrated design process and a near-real time performance simulation approach for fast feedbacks at the early stage of the integrated design process.

A design process module “Magic Cube” (MC) was developed for the VDS as the core for the design integration and coordination. It …

Effects Of Air Pollution, Temperature And Moisture Content On Copper And Silver Corrosions And The Reliability Of Data Center Equipment, Rui Zhang

Dissertations - ALL

The effects of moisture content, temperature, and pollutant mixture on atmospheric corrosion of copper and silver were investigated by exposing test specimens to different environmental conditions, followed by surface characterization using the coulometric reduction, Scanning Electron Microscopy, and Energy Dispersive Spectrometry (SEM/EDS). Printed circuit board test cards (PCBs) with bare copper were also used to investigate the effects of voltage bias on the PCBs on the corrosion rate. The test specimens were exposed to mixed flowing gases (MFG) environment with eight different combinations of the following five pollutants at the fixed concentration levels: 60 ppb O3, 80 ppb NO2, 40 …