Mechanical Engineering Commons^™

Fuel-Rich Hetero-/Homogeneous Combustion Of C3h8/O2/N2 Mixtures Over Rhodium, John Mantzaras, Ran Sui, Rolf Bombach

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The catalytic (heterogeneous) and gas-phase (homogeneous) combustion of C3H8/O2/N2 mixtures over rhodium was investigated experimentally and numerically at 5 bar and at fuel-rich equivalence ratios π = 2.0-3.5 relevant to propane Catalytic Partial Oxidation (CPO). In situ spatially-resolved Raman measurements of major gas-phase species concentrations and Planar Laser Induced Fluorescence (PLIF) of formaldehyde were applied in an optically accessible channel-flow reactor to monitor the catalytic and gas-phase processes, respectively, while accompanying 2D simulations were carried out with detailed hetero-/homogeneous chemical reaction mechanisms. Due to the high gas-phase reactivity of propane, homogeneous chemistry could not be ignored over most of the …

Regulation Of Dendrite-Free Li Plating Via Lithiophilic Sites On Lithium-Alloy Surface, Yufang He, Mengyun Zhang, Aiping Wang, Bo Zhang, Hiep Pham, Qiao Hu, Li Sheng, Hong Xu, Li Wang, Jonghyun Park, Xiangming He

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Lithium (Li) deposition behavior plays an important role in dendrite formation and the subsequent performance of lithium metal batteries. This work reveals the impact of the lithiophilic sites of lithium-alloy on the Li plating process via the first-principles calculations. We find that the Li deposition mechanisms on the Li metal and Li22Sn5 surface are different due to the lithiophilic sites. We first propose that Li plating on the Li metal surface goes through the "adsorption-reduction-desorption-heterogeneous nucleation-cluster drop "process, while it undergoes the "adsorption-reduction-growth "process on the Li22Sn5 surface. The lower adsorption energy contributes to the easy adsorption of Li on …

Direct Numerical Simulation Of Acoustic Disturbances In A Hypersonic Two-Dimensional Nozzle Configuration, Nathaniel Hildebrand, Meelan M. Choudhari, Cole P. Deegan, Junji Huang, Lian Duan

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Direct numerical simulations (DNS) are performed to study acoustic radiation in a quasi-two-dimensional nozzle with two independents spatially evolving turbulent boundary layers with an edge Mach number of 6. The emphasis of this work is to compare the radiated pressure fluctuations in a geometrically confined environment with those radiated from a single wall in an unconfined setting. The boundary-layer profile of the rms pressure fluctuation scaled by the mean shear stress at the wall is found to be in good agreement with prior flat-plate calculations at similar conditions. However, the normalized rms pressure fluctuation within the freestream p region is …

Neural Network Attitude Control System Design For The Wallops Arc-Second Pointer, Pavel Galchenko, Henry J. Pernicka

Mechanical and Aerospace Engineering Faculty Research & Creative Works

No abstract provided.

Nanobubble Capillary Force Between Parallel Plates, Eric Bird, Zhi Liang

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The Aggregation of Fine or Ultrafine Particles in Liquid Due to the Nanobubble (NB) Bridging Capillary Force is a Key Process for Many Industrial Applications. the Magnitude and Direction of the NB Capillary Force (NBCF) Are Directly Affected by the Geometry of the NB Gas Bridge between Two Adjoining Particles. Although the NBCF Can Be Accurately Measured using Experimental Techniques, It is Very Challenging to Monitor the Images of a NB Capillary Bridge in Nanoscale Spatial Resolution in NBCF Measuring Experiments. as a Result, the Capillary Force Model that Predicts the Dependence of the NBCF on the Geometry of the …

Feature Learning For Optimal Control With B-Spline Representations, Vinay Kenny, Sixiong You, Chaoying Pei, Ran Dai

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The paper develops a feature learning-based method to solve optimal control problems using B-splines to approximate the optimal solutions. The feature learning-based optimal control method can quickly generate near-optimal trajectories for general optimal control problems subject to system dynamics and constraints. The steps in the proposed method are as follows: Firstly, by representing the state and control variables with B-spline functions, the optimal control problem is converted into an approximate nonlinear programming (NLP) problem, where parameters of the B-splines are identified as features of the optimal solution. Secondly, for a specific problem with designated inputs, a dataset of the optimal …

Microstructural Development In Inconel 718 Nickel-Based Superalloy Additively Manufactured By Laser Powder Bed Fusion, Thinh Huynh, Abhishek Mehta, Kevin Graydon, Jeongmin Woo, Sharon Park, Holden Hyer, Le Zhou, D. Devin Imholte, Nicolas E. Woolstenhulme, Daniel M. Wachs, Yongho Sohn

Mechanical Engineering Faculty Research and Publications

Excellent weldability and high temperature stability make Inconel 718 (IN718) one of the most popular alloys to be produced by additive manufacturing. In this study, we investigated the effects of laser powder bed fusion (LPBF) parameters on the microstructure and relative density of IN718. The samples were fabricated with independently varied laser power (125–350 W), laser scan speed (200–2200 mm/s), and laser scan rotation (0°–90°). Archimedes’ method, optical microscopy, and scanning electron microscopy were employed to assess the influence of LPBF parameters on the relative density and microstructure. Optimal processing windows were identified for a wide range of processing parameters, …

Design Of Affordable Polyaniline - Based Wearable Sensor For Real Time Plant Growth Monitoring, Temitope Borode

Electronic Theses and Dissertations

The need for precision agriculture in today and future farming cannot be overstressed. Recent agriculture is characterized by numerous challenges such as environmental stressors and resource constraints resulting in low crop yield and unsustainable agriculture practices. Understanding plant growth mechanism and growth rate under the external influence is a bedrock towards precision agriculture practices ensuring optimum yield and sustainable utilization of resources. The current study addresses this need by developing and applying an affordable and stable sensor for monitoring plant growth. The sensor was fabricated by in-situ chemical polymerization of aniline on an elastic band substrate by dip coating. The …

Oxidative Aging And Fracture Behavior Of Polymers And Composites: Theory, Modeling And Experiments, Shabnam Konica

Dissertations, Master's Theses and Master's Reports

Polymers and their composites (PMC) have emerged as effective alternative materials in structural, aerospace, and automotive industries due to their lightweight and tunable properties compared to metals. However, these materials tend to degrade during their operations in extreme environments. In this work, two extreme conditions are considered: - i) high-temperature oxidative degradation of polymers and polymer-based composites ii) Fracture and damage of polymer-based composites under thermo-mechanical loading.

Polymer oxidation starts when oxygen from the ambient diffuses into the bulk material and initiates chemical reactions to develop a coarse, brittle oxide layer on the exposed surface. The oxidative degradation process is …

Model Predictive Control Of Energy Systems For Heat And Power Applications, Chethan Ramakrishna Reddy

Dissertations, Master's Theses and Master's Reports

Building and transportation sectors together account for two-thirds of the total energy consumption in the US. There is a need to make these energy systems (i.e., buildings and vehicles) more energy efficient. One way to make grid-connected buildings more energy efficient is to integrate the heating, ventilation and air conditioning (HVAC) system of the building with a micro-scale concentrated solar power (MicroCSP) sys- tem. Additionally, one way to make vehicles driven by internal combustion engine (ICE) more energy efficient is by integrating the ICE with a waste heat recovery (WHR) system. But, both the resulting energy systems need a smart …

Molecular Modeling Of High-Performance Thermoset Polymer Matrix Composites For Aerospace Applications, Prathamesh P. Deshpande

Dissertations, Master's Theses and Master's Reports

The global efforts from major space agencies to transport humans to Mars will require a novel lightweight and ultra-high strength material for the spacecraft structure. Three decades of research with the carbon nanotubes (CNTs) have proved that the material can be an ideal candidate for the composite reinforcement if certain shortcomings are overcome. Also, the rapid development of the polymer resin industry has introduced a wide range of high-performance resins that show high compatibility with the graphitic surface of the CNTs. This research explores the computational design of these materials and evaluates their efficacy as the next generation of aerospace …

Development Of Advanced Models For Pre-Ignition Prediction In Gas Engines And Analytical Model For Wallfilm Evaporation, Ankith Ullal

Dissertations, Master's Theses and Master's Reports

Ever-changing regulations aimed at improving efficiency and reducing harmful emissions have resulted in many power-generation device (engine) manufacturers to adopt new strategies. Computer simulation of these new strategies of power generation requires more accurate and higher fidelity modelling tools. In the present study, two such models are developed. The first model deals with pre-ignition phenomena driven by lubricant (lube) oil in natural gas engines and the second model is relevant to prediction of wallfilm evaporation by employing analytical solutions to transport governing equations for boundary layers.

Pre-ignition in engines has been the subject of current research with the advent of …

On-Ice Detection, Classification, Localization And Tracking Of Anthropogenic Acoustic Sources With Machine Learning, Steven J. Whitaker

Dissertations, Master's Theses and Master's Reports

Arctic acoustics have been of concern in recent years for the US navy. First-year ice is now the prevalent factor in ice coverage in the Arctic, which changes the previously understood acoustic properties. Due to the ice melting each year, anthropogenic sources in the Arctic region are more common: military exercises, shipping, and tourism. For the navy, it is of interest to detect, classify, localize, and track these sources to have situational awareness of these surroundings. Because the sources are on-water or on-ice, acoustic radiation propagates at a longer distance and so acoustics are the method by which the sources …

Characterization Of Hydraulic Flow Noise Induced By Spool Valves, Carter A. Paprocki

Dissertations, Master's Theses and Master's Reports

The purpose of the hydraulic flow noise research was to investigate the relationship between operational valve parameters and flow noise generation. The primary consideration was correlating the flow noise generated by the valve with the distinct valve open positions. This data would allow future valve designs to account for features that cause increased flow noise and move those features away from high flow valve displacements. By implementing this, companies would be able to design quieter hydraulic systems that will not expose operators to the current levels of sound found on machines. The experiments were conducted using two valves with different …

Calorimetric Measurements Of Lunar Regolith Simulant And Water. An Experimental Study Correlating Weight Percent Water And Temperature Change Through Periods Of Phase Change., George B. Johnson

Dissertations, Master's Theses and Master's Reports

Permanently Shaded Regions (PSRs) are cold traps located around the lunar south pole that have been confirmed to contain possible interesting quantities or volatiles such as H2O, CO2, SO2, CH4, and others. [1] The identification of these volatiles on the lunar surface was a critical step in the development of NASA’s strategic goals for scientific discoveries, sustained space travel and exploration, and re-establishing a human presence on the moon. These volatiles are vital to the future of operating in and exploring space. The LCROSS impact revealed the existence of these resources in PSRs but more information is needed about the …

Mechanical Property Evaluation Of Additively Manufactured Materials Across A Wide Temperature Range, Sanket Vinayak Hirve

Electronic Theses and Dissertations

Additive manufacturing (also called 3d printing) has transitioned from a prototyping-only technology to a technology that is able to create usable parts with complex geometries. 3D printed parts are beginning to be used across all areas of engineering, such as biomedical, aerospace, automobile and many more. Typically, the term “3D printing” refers to layer by layer deposition of polymer materials, while the term “additive manufacturing” refers to layer by layer metal deposition. Conventional manufacturing, or substrative manufacturing, has several main problems that additive manufacturing can help overcome, such as high cost for low volume production, inability to create very complex …

Project-Based Learning In Non-Traditional Settings In Engineering Education, Mary Foss

Electronic Theses and Dissertations

The purpose of this study is to examine the effectiveness of utilizing the principles of Project-based learning (PJBL) in nontraditional settings in engineering education. There is ample literature related to the usage of PJBL techniques in engineering education but there are also challenges with incorporating PJBL within the curriculum. It is the aim of this dissertation to build upon this understanding of the advantages and limitations of PJBL in engineering education and identify areas within the existing body of knowledge in which more research is needed. This dissertation divides this topic into 4 sub-topics. The first sub-topic explores how PJBL …

Mechanical Behavior Of Plain Weave Nylon Reinforced Drop-Stitch Inflatable Panels, Anthony J. White

Open Access Master's Theses

All CUI (Controlled Unclassified Information) is U.S. government property and has been removed from this thesis.

Mechanical Response Of Constituent Materials Used In Plain Weave Nylon Reinforced Inflatable Drop Stitch Structures, Matthew S. Buglio

Open Access Master's Theses

All CUI (Controlled Unclassified Information) is U.S. government property and has been removed from this thesis.

Investigation Of The Effects Of Weave Geometry On The Mechanical Response Of Woven Fabrics, Rogan Daniel Kennedy

Open Access Master's Theses

Document is CUI.

An Experimental Study Towards Underwater Propulsion System Using Structure Borne Traveling Waves, Shreyas Suhas Gadekar

Dissertations, Master's Theses and Master's Reports

The method of generating steady-state structure-borne traveling waves underwater in an infinite media creates abundant opportunities in the field of propulsive applications, and they are gaining attention from several researchers. This experimental study provides a framework for harnessing traveling waves in a 1D beam immersed under quiescent water using two force input methods and providing a motion to an object floating on the surface of the water.

In this study, underwater traveling waves are tailored using structural vibrations at five different frequencies in the range of 10Hz to 300Hz. The resulting fluid motion provides a propulsive thrust that moves a …

A Review On Heat Flux Measurement Techniques In The Nano And Microscale, Miguel Moreno

Honors Program: Senior Projects (Public)

Heat Flux measurements represent an important step in obtaining an accurate heat transfer profile in many engineering problems. Sensors capable of measuring this quantity have been around for decades, however, the increasing focus in nano and microscale applications in the industry and academia demands more accurate and smaller devices. This paper reviews some of the methods used to develop heat flux meters targeted to nano and microscale, as well as some calibration processes for the same. A combination of Luminescence and non-luminescence methods for direct and indirect measurement of heat flux will be discussed. A glimpse of what the future …

Efficient Near Infrared To Visible Light Upconversion From Er/Yb Codoped Pvdf Fibrous Mats Synthesized Using A Direct Polymer Doping Technique, Saptasree Bose, Jack Ryan Summers, Bhupendra B. Srivastava, Victoria Padilla-Gainza, Manuel Peredo, Carlos Trevino De Leon, Bryan Hoke, Santosh K. Gupta, Karen Lozano

Mechanical Engineering Faculty Publications

Highlights

• Direct Rare Earth doping in PVDF Polymer to overcome powder limitation.

• PVDF Fiber with smooth and defect free texture designed by Forcespinning.

• Doping Enhances Beta fraction of PVDF without affecting thermal Stability.

• Efficient upconversion of NIR into visible light in PVDF:Yb3+,Er3+ fibrous mats.

• Two-Photon absorption for both green and red upconversions.

Abstract

Upconverting-materials are capable of converting near infra-red (NIR) excitation into lower wavelengths. These materials could have a myriad of promising potential applications. However, in some areas, its use has been hindered by its low upconversion luminescence (UCL) efficiency and processing/handling disadvantages from luminescent materials in powder form. …

Controlling The Thermal And Electrical Properties Of Camno3-Δ Based Perovskite Ceramics, Sergio Andres Paredes Navia

Graduate Theses, Dissertations, and Problem Reports (ETD)

Most of the energy lost during the conversion process comes in the form of waste heat. The world's energy consumption loses over 60% of its energy after conversion. In order to increase the efficiency of the conversion process, it is essential to harness waste heat and reutilize this energy resource. Heat recovery technology as thermoelectric (TE) technology is one of the growing alternatives to harvest excessive amounts of energy lost as waste heat for a more efficient, safe, and sustainable future. Due to the Seebeck effect, TE materials have the potential to convert waste heat directly into electricity, improving efficiency …

Post-Processing Precise Point Positioning Solutions With Parameter Optimization, Maria A. Gonzalez Castaneda

Graduate Theses, Dissertations, and Problem Reports (ETD)

Precise Point Positioning (PPP) technique can offer position solutions with centimeter-level accuracy by fusing precise satellite orbits and clocks with un-differenced, dual-frequency, pseudo-range, and carrier-phase observables. PPP presents a compelling alternative to Differential Global Positioning Systems, with the benefit that it only requires a single receiver and does not require simultaneous observations from many stations, making it appealing for ongoing research on hydro-graphic survey applications. The National Oceanic and Atmospheric Administration has been working on a buoy system tracked with a Global Positioning Systems receiver and Inertial Measurement Unit sensor using the PPP technique. In the interest of obtaining accurate …

Development Of Methane Emissions Model To Assess Fuel Recovery Potential At Gas Well Sites Using On Site Compression, Nicholas G. Lindenfeldar

Graduate Theses, Dissertations, and Problem Reports (ETD)

The US natural gas production and consumption has increased 85.5% since 2005 primarily due to the unconventional production methods of horizontal drilling and hydraulic fracturing. Natural gas used as a fuel has a lower greenhouse gas (GHG) footprint than coal and petroleum due to lower Carbon Dioxide (CO₂) emissions when combusted. However, the “greener” benefit to natural gas may be consumed by leaks in production and transmission systems. Methane (CH₄), the primary hydrocarbon in natural gas, has an estimated Global Warming Potential (GWP) of 28-36 over 100 years, meaning it can absorb 28-36 more energy than …

Precise Landing Of Vtol Uavs Using A Tether, Jeremy W. Rathjen

Graduate Theses, Dissertations, and Problem Reports (ETD)

Unmanned Aerial Vehicles (UAVs), also known as drones, are often considered the solution to complex robotics problems. The significant freedom to explore an environment is a major reason why UAVs are a popular choice for automated solutions. UAVs, however, have a very limited flight time due to the low capacity and weight ratio of current batteries. One way to extend the vehicles' flight time is to use a tether to provide power from external batteries, generators on the ground, or another vehicle. Attaching a tether to a vehicle may constrain its navigation but it may also create some opportunities for …

High Energy And Power Density Peptidoglycan Musclesthrough Super-Viscous Nanoconfined Water, Haozhen Wang, Zhi-Lun Liu, Jianpei Lao, Sheng Zhang, Rinat Abzalimov, Tong Wang, Xi Chen

Advanced Science Research Center

Water-responsive (WR) materials that reversibly deform in response to humidity changes show great potential for developing muscle-like actuators for miniature and biomimetic robotics. Here, it is presented that Bacillus (B.) subtilis’ peptidoglycan (PG) exhibits WR actuation energy and power densities reaching 72.6 MJ m−3 and 9.1 MW m−3, respectively, orders of magnitude higher than those of frequently used actuators, such as piezoelectric actuators and dielectric elastomers. PG can deform as much as 27.2% within 110 ms, and its actuation pressure reaches ≈354.6 MPa. Surprisingly, PG exhibits an energy conversion efficiency of ≈66.8%, which can be attributed to its super-viscous nanoconfined …

Schaeffler F-250 Bev Conversion: Power Electronics, Leslie Sawyer

Williams Honors College, Honors Research Projects

This report shows the work that was done on the power electronics system in the industry sponsored Schaeffler demonstration truck project. The goal of the project was to convert a combustion Ford F250 into a battery electric vehicle, while using as much Schaeffler technology as possible. After the vehicle is converted it will be used as a demonstration vehicle to show potential investors. While this project is still in progress, the work that was done during this time was substantial to the development of this project. Progress that has been made on the power electronics system includes developments in selecting …

Quickcut Waterjet Cutter, Kennedy Dunn, Jacob Storrow, Benjamin Laughrey

Williams Honors College, Honors Research Projects

The QuickCut Waterjet Cutter was created in 2019 as a senior design project. This is the third iteration of the waterjet cutter. The goal of this project was to create an operable CNC waterjet cutter that is able to cut 1/16” tensile specimens consisting of nonferrous metal or plastic. This machine will be utilized in the Manufacturing Laboratory at the University of Akron to provide education to interested students on the waterjet cutting process, how it operates, and industrial application of the technology. Waterjet cutting is a subtractive manufacturing process which is recognized for its specialized applications such as cutting …