Mechanical Engineering Commons^™

Design And Scale Model Of Wave Generator For The Testing Of Wave Energy Conversion Devices, Amanda Olla

Master's Theses

As the climate crisis draws more concern, research and development in wave energy as a renewable energy source has increased. Devices such as wave energy converters (WECs) are being researched, tested, and implemented to make wave energy a competitive power source. Testing of these devices is limited due to environmental concerns such as weather, location, and other issues. WECs require testing in a marine environment, however, performing testing in the actual environment may be difficult due to weather, access, mounting, and other issues. To eliminate environmental unknowns from testing, a wave simulator device can mimic wave behavior without the need …

Ai-Based Bridge And Road Inspection Framework Using Drones, Hovannes Kulhandjian

Mineta Transportation Institute

There are over 590,000 bridges dispersed across the roadway network that stretches across the United States alone. Each bridge with a length of 20 feet or greater must be inspected at least once every 24 months, according to the Federal Highway Act (FHWA) of 1968. This research developed an artificial intelligence (AI)-based framework for bridge and road inspection using drones with multiple sensors collecting capabilities. It is not sufficient to conduct inspections of bridges and roads using cameras alone, so the research team utilized an infrared (IR) camera along with a high-resolution optical camera. In many instances, the IR camera …

An Investigation Into The Challenges Of Contemporary Additive Manufacturing: Insights Into The Metallurgical Response Of Materials And Relevant Solution, Huan Ding

LSU Doctoral Dissertations

Additive Manufacturing (AM) has gained attention in recent years due to its unique capabilities in the fabrication of complex parts. As with any new research, there is still a lack of sufficient understanding in the field of additive manufacturing, and further investigation is needed to solve existing problems. Ultimately, the aim is to enable the widespread use of AM components across various industries.

Chapter One provides a brief introduction to the background and current bottlenecks of additive manufacturing technology. Chapter two focuses on the development of high-strength 7075 aluminum alloy (Al7075) for Fused Deposition Modeling and Sintering (FDMS) technology. Al7075 …

Multicolor Dye-Based Flow Structure Visualization For Seal-Whisker Geometry Characterized By Computer Vision, Ondřej Ferčák, Kathleen Lyons, Christin T. Murphy, Kristina M. Kamensky, Raul Bayoan Cal

Mechanical and Materials Engineering Faculty Publications and Presentations

Pinniped vibrissae possess a unique and complex three-dimensional topography, which has beneficial fluid flow characteristics such as substantial reductions in drag, lift, and vortex induced vibration. To understand and leverage these effects, the downstream vortex dynamics must be studied. Dye visualization is a traditional qualitative method of capturing these downstream effects, specifically in comparative biological investigations where complex equipment can be prohibitive. High-fidelity numerical simulations or experimental particle image velocimetry (PIV) are commonplace for quantitative high-resolution flow measurements, but are computationally expensive, require costly equipment, and can have limited measurement windows. This study establishes a method for extracting quantitative data …

Towards A Virtual Test Framework To Predict Residual Compressive Strength After Lightning Strikes, Scott L.J. Millen, Xiaodong Xu, Juhyeong Lee, Suparno Mukhopadhyay, Michael R. Wisnom, Adrian Murphy

Mechanical and Aerospace Engineering Faculty Publications

A novel integrated modelling framework is proposed as a set of coupled virtual tests to predict the residual compressive strength of carbon/epoxy composites after a lightning strike. Sequentially-coupled thermal-electric and thermo-mechanical models were combined with Compression After Lightning Strike (CAL) analyses, considering both thermal and mechanical lightning strike damage. The predicted lightning damage was validated using experimental images and X-ray Computed Tomography. Delamination and ply degradation information were mapped to a compression model, with a maximum stress criterion, using python scripts. Experimental data, in which artificial lightning strike and compression testing were performed, was used to assess the predictive capabilities …

On Quantifying Uncertainty In Lightning Strike Damage Of Composite Laminates: A Hybrid Stochastic Framework Of Coupled Transient Thermal-Electrical Simulations, R. S. Chahar, J. Lee, T. Mukhopadhyay

Mechanical and Aerospace Engineering Faculty Publications

Lightning strike damage can severely affect the thermo-mechanical performance of composite laminates. It is essential to quantify the effect of lightning strikes considering the inevitable influence of material and geometric uncertainties for ensuring the operational safety of aircraft. This paper presents an efficient support vector machine (SVM)-based surrogate approach coupled with computationally intensive transient thermal-electrical finite element simulations to quantify the uncertainty in lightning strike damage. The uncertainty in epoxy matrix thermal damage and electrical responses of unprotected carbon/epoxy composite laminates is probabilistically quantified considering the stochasticity in temperature-dependent multi-physical material properties and ply orientations. Further, the SVM models are …

Mems Cantilever Biosensors Driven By Fringe Effect: Voltage-Amplitude Response Of Parametric Resonance, Miguel A. Martinez, Dumitru I. Caruntu

Mechanical Engineering Faculty Publications

This paper deals with voltage-amplitude response of fringing field/effect actuated micro-electromechanical system (MEMS) cantilever beam resonator biosensors at parametric resonance. The system consists of a flexible electrode (cantilever beam) and a fixed electrode (ground plate) in parallel, connected through an AC voltage source. The electrostatic force induced is due to the parallel-plate capacitance, which is directly related to the overlapping area of the two electrodes (Palmer’s Formula). In addition, fringing field electrostatic actuation must be accounted for. This is due to the bending of electric field lines from the ground plate to the top and side walls of the cantilever …

Amplitude-Voltage Response Of Parametric Resonance Of Electrostatically Actuated Circular Membranes, Marcos Alipi, Dumitru I. Caruntu

Mechanical Engineering Faculty Publications

This paper deals with the amplitude-voltage response of parametric resonance of electrostatically actuated MEMS circular membranes resonator for sensing applications. The system consists of a flexible circular membrane over a parallel ground plate. A soft AC voltage is applied between the MEMS membrane and ground plate to actuate the membrane near its first natural frequency. Two methods of investigation are used in this research, namely the method of multiple scales (MMS), and the reduced order model (ROM). These methods were used to solve for the voltage response of the MEMS analytically and numerically. This work also reports the effects the …

Kinematic Analysis Of Gait And Deep Knee Flexion For Pre- And Post-Operative Total Knee Arthroplasty, Samantha Collins

Electronic Theses and Dissertations

Osteoarthritis (OA) is a form of arthritis that develops in the joint due to overuse and aging causing pain, discomfort, and disability. Total Knee Arthroplasty (TKA) is a surgical procedure performed when OA symptoms are severe with an estimated 600,000 patients in the United States currently receiving TKA. Studies have reported dissatisfaction of the knee for 14-39% of patients. This study collected knee kinematics before and after surgery using stereo radiography for precise measurement of gait and deep knee flexion activities. Results showed healthy knee kinematics were not restored and no significant changes could be seen from OA kinematics in …

Exploration Of Motion Capture System To Investigate Human Shoulder Kinematics, Ola Alsaadi

Electronic Theses and Dissertations

The glenohumeral joint (GH) is commonly conceptualized as a ball-and-socket joint [1], and its center of rotation (COR) is presumed to coincide with the geometric center of the medial-superior region of the humeral head [2]. Recent research has endorsed improvements in COR estimation through invasive and noninvasive techniques, including cadaver studies, stereophotogrammetry, and motion capture (MOCAP) systems. Despite increased interest in wearable technology within human movement analysis, the problem of COR estimation employing MOCAP systems and its validation against bi-planar fluoroscopy remains relatively unexplored.

This study employed a marker-based MOCAP system to compare the accuracy, error, and precision of three …

Computational Methodology For Generating Patient-Specific Soft Tissue Representations, Ahilan Anantha Krishnan

Electronic Theses and Dissertations

This dissertation focused on modeling specimen-specific soft tissue structures in the context of joint replacement surgery. The research addressed four key aspects. The first study involved developing a workflow for creating finite element models of the hip capsule to replicate its torque-rotational response. Experimental data from ten cadaveric hips were used to calibrate the models, resulting in improved accuracy and relevance for surgical planning and implant design. The second study tackled the challenge of expediting the calibration of mechanical properties of the hip capsule to match patient-specific laxities. A statistical shape function model was proposed to generate patient-specific finite element …

Digital Twins Of The Living Knee: From Measurements To Model, Thor Erik Andreassen

Electronic Theses and Dissertations

Modern medicine has dramatically improved the lives of many. In orthopaedics, robotic surgery has given clinicians superior accuracy when performing interventions over conventional methods. Nevertheless, while these and many other methods are available to ensure treatments are performed successfully, far fewer methods exist to predict the proper treatment option for a given person. Clinicians are forced to categorize individuals, choosing the best treatment on “average.” However, many individuals differ significantly from the “average” person, for which many of these treatments are designed. Going forward, a method of testing, evaluating, and predicting different treatment options' short- and long-term effects on an …

Aerodynamic & Aeroacoustic Performance Of Wind Turbine Blades Featuring Enhanced Flow-Control, Md Zishan Akhter

Dissertations

Wind energy, being one of the cleanest and most sustainable sources, has undergone remarkable growth in recent years due to advancements in aerodynamics and increased power output. The research community is actively pursuing the development of cutting-edge solutions to further optimize wind turbine technology, ensuring its maximum efficiency and revolutionizing the landscape of wind power.
/="/">This research aims to design and develop flow-control devices for wind turbine blades, employing both active and passive control mechanisms, namely morphing trailing-edge and slot-profile, respectively. The objective is to enhance wind turbine performance across a wide range of wind speeds. The morphing trailing-edge …

Analysis Of Bombyx Mori Silk And Polyimide Nanofibers, Sabrina Leseul

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

This thesis presents a study on the properties of Bombyx Mori silk nanofibers and polyimide (PI) nanofibers. Firstly, a Bombyx Mori silk solution has been created with degummed silkworm cocoons in order to separate the fibroin and the sericin, the two main proteins of the silk. The fibroin was then centrifuged to remove insoluble particles and stored and 4°C before mixing with hexafluoroisopropanol (HFIP). On the second part, a polyimide solution, made with shavings of polyimide and N,N-dimethylformamide (DMF). Both solutions are then electrospun. Electrospinning parameters are studied. In this way, a part of my thesis has been dedicated to …

Applications Of Femtosecond Laser-Processed And Nanoneedle-Synthesized Surfaces To Enhance Pool Boiling Heat Transfer, Peter Efosa Ohenhen

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

In the present work, the integration of femtosecond laser surface processing (FLSP) with copper hydroxide on hybrid surfaces was examined. The goal was to determine the impact on pool boiling enhancement. The samples for the investigation were fabricated by first functionalizing with FLSP, and the process was then followed by citric acid cleaning (CAC) to eliminate the oxides generated on the copper surface during the FLSP process. After the citric acid cleaning, the samples were immersed in ethanol and subjected to an ultrasonic bath for 25 minutes. This step was performed to eliminate any residual citric acid and loose particles. …

A Generalized Machine Learning-Based Classifier Considering Cost-Effective Features For Automated Fault Detection And Diagnosis (Afdd) Of Packaged Rooftop Units, Md Rasel Uddin

Dissertations and Doctoral Documents, University of Nebraska-Lincoln, 2023–

Packaged rooftop units (RTUs) are widely used for space conditioning in commercial buildings and manufacturing facilities. The typical soft faults related to RTUs degrade the system's performance in terms of cooling capacity, power consumption, and Coefficient of Performance (COP), detrimentally affecting both the equipment and energy consumption and the environment. Previous research in soft fault detection for rooftop units lacked classifier validation using lab and field data, developing a generalizable algorithm, and analyzing its performance across varying fault intensities.

Using a simulated data library for multiple rooftop units, this study proposes a machine-learning classifier with a reduced set of 9 …

Data And Cad Models Of Cyclic Testing Of Membrane Hinges For Use In Origami-Inspired Design, Mitchel Skinner

ScholarsArchive Data

The following includes results and CAD models of cyclic testing of membrane hinges for use in origami-inspired design. The results include the number of cycles until both visual damage and complete failure occurred in 7 different membrane materials. The CAD models of the testing setup are also included.

Electromagnetic Mems Safety And Arming Devices, Fatima Rashed Alnuaimi

Theses

This thesis aims to investigate the design of safety and arming devices within artillery fuzes, which rely on the spin velocity and setback acceleration of the weapon. These systems consist of two critical components: the spin lock and the inertia lock. The spin velocity and setback acceleration of the weapon induce deformations in these components, serving as key criteria for determining whether the weapon is in an armed or safe state.

The primary objective of this thesis is to comprehensively analyze and assess the design of both the spin lock and inertia lock. The research will delve into multiple factors …

Heat Transfer Performance Of Single-Phase Circular Heat Sink With Micro Pin-Fin, Mouza Abdulla Al Shamsi

Theses

This thesis presents a numerical study of laminar forced convection in a novel design of a microscale single phase water cooled circular heat sink with pin fins developed and analyzed to serve as a miniaturized cooling system. The developed heat sink in this study aims to achieve efficient heat dissipation from high electronics integration that generates high heat flux and non-uniform temperature distribution, which leads to the reduction of life and reliability of electronic devices.

Numerical analysis of ten different configurations of the circular heat sink has been carried out for the heat flux of 100 W/cm2 at range of …

Experimental Study Of Central And Side Jet With And Without Chevron Nozzle Exit On Gas Turbine Leading Edge Jet Impingement Cooling, Ahmad Yousef Alqasrawi

Theses

This thesis presents a comprehensive investigation into the application of jet impingement cooling on turbines blade leading edge. Gas turbines are extensively utilized in power generation and aerospace industries, where efficient cooling techniques are crucial to enhance the performance and lifespan of turbine blades. The leading edge of a turbine blade is particularly vulnerable to high-temperature exposure and thermal stresses, making it an essential area for effective cooling strategies. Jet impingement cooling is one of the most effective cooling techniques mostly used in the leading edge of rotating and stationary blades. This study aims to explore the performance of jet …

Design And Fem Modelling Of Mems Capacitive Accelerometer And Gyroscope For Quadcopter/Uav Applications, Shaikha Rashid Alnaqbi

Theses

This study presents the design, simulation, and analysis of Micro Electromechanical Systems (MEMS) sensors, constituting the principal components of MEMS-based Inertial Measurement Units (IMUs). The main objective of the study is to design, simulate and analyze 3-axis capacitive accelerometer and 3-axis gyroscope. The MEMS-based capacitive accelerometers and gyroscope are analyzed using Ansys Workbench. Modal, Static Structural and harmonic analysis are used to obtain resonant frequencies, deformation/stress and profile of amplitude over a wide range of frequencies. Mechanical sensitivity analysis of the designed accelerometer and gyroscope is performed using the Finite Element Method (FEM). Analytical Equations are developed to calculate mechanical …

Development Of Guidance, Navigation, And Control Systems For Multi-Spacecraft Assembly In Proximity Operations, Mohammed Ayman Atallah

Theses

This thesis presents the development of Guidance, Navigation, and Control (GNC) algorithms for multi-spacecraft assembly in proximity operations. A 3-DOF mathematical model of spacecraft relative translational motion is derived using the Euler-Lagrange method. Additionally, a 6-DOF mathematical model of spacecraft relative translational and rotational motion is derived using the twistor method, with consideration for the kinematic coupling effect. A new Linear Time-Invariant (LTI) model is developed based on the twistor model, which is utilized in the design of the GNC systems. Both LTI Model Predictive Control (MPC) and Linear Time-Varying (LTV) MPC algorithms are employed to develop Guidance and Control …

Development Of A Vortex-Cooled Bipropellant Thruster And Evaluation Of Performance Characteristics With Respect To Injection Parameters, Mousa Adnan Aqailan

Theses

This study presents an experimental assessment of the cooling performance and efficiency of a 10N-vortex-cooled Propane/Gox bi-propellant thruster that was fabricated using metal and thermoplastic material. The proposal of injecting an oxidizer in a vortex pattern was suggested as a potential cooling method for semi-thermoplastic constructed thrust engines. This method has been demonstrated as a promising candidate for integrated cooling and can be manufactured using 3D printing technology. In contrast to typical complicated cooling systems and their attributed common downsides; the vortex injection can be 3D printed as a single solid piece thruster, thereby reducing design complexity, weight, and manufacturing …

A Review On The Coalescence Of Confined Drops With A Focus On Scaling Laws For The Growth Of The Liquid Bridge, Sangjin Ryu, Haipeng Zhang, Udochukwu John Anuta

Department of Mechanical and Materials Engineering: Faculty Publications

The surface–tension-driven coalescence of drops has been extensively studied because of the omnipresence of the phenomenon and its significance in various natural and engineering systems. When two drops come into contact, a liquid bridge is formed between them and then grows in its lateral dimensions. As a result, the two drops merge to become a bigger drop. The growth dynamics of the bridge are governed by a balance between the driving force and the viscous and inertial resistances of involved liquids, and it is usually represented by power–law scaling relations on the temporal evolution of the bridge dimension. Such scaling …

Dependence Of The Granulometric Composition Of Chalk During Granulation In A Turbulized Layer, N.A. Annaev, S.Kh. Nurmukhamedov, Zh.V. Sultonov, N.Sh. Khudoiberdieva

Chemical Technology, Control and Management

The article presents the results of an experimental study on chalk granulation in the turbulized layer of a turboblade granulator. The design of the apparatus combines the following sequential processes: grinding, granulating and compacting newly formed granules. In addition, this device has the ability to carry out both rotational and reciprocating motion. It has been established that preliminary grinding of the feedstock increases the efficiency of the granulation process and improves the quality of the finished product. In the experiments, four substances were used to create 2 astringent suspensions and the optimal combination and their ratios were determined. The experiments …

Revealing Interface-Assisted Plastic Anisotropy Via In Situ Transmission Electron Microscopy Tension Of Lamellar Tial, Zhixiang Qi, Qi Zhu, Jian Wang, Yuede Cao, Fengrui Chen, Jiangwei Wang, Yang Chen, Gong Zheng, Guang Chen

Department of Mechanical and Materials Engineering: Faculty Publications

Assembling functional units into specific orientation organizations based on functional unit and organization (FUO) paradigm can maximize utilizing mechanical property anisotropy of lamellar-structured materials. However, the origin of their anisotropic deformation behaviors has not been clearly understood. Taking the fully lamellar γ-TiAl/ α₂-Ti₃Al dual-phase single crystal as an example, we decouple the interface functional units governed anisotropic plastic deformation through in situ transmission electron microscopy tensile testing and multiscale microstructural characterizations. The orientation organization-dependent slip continuity across the γ/α₂ interface and interface strength play a determinant role in plastic anisotropy beyond intrinsic dislocation activities within …

Top-Down Nanomanufacturing Of Anisotropic Two-Dimensional Metals, Md Rubayat-E Tanjil

USF Tampa Graduate Theses and Dissertations

Two-dimensional (2D) materials have introduced a transformative era in materials science with extensive research being performed to gain a fundamental understanding of their diverse properties and applications. Amongst the broader 2D material family, 2D metals or 2D metallic nanosheets (2DMNSs) typically denotes the nanometer-scale thin elemental metals, compound, or alloys, which shows superlative chemical and physical properties compared to bulk counterparts due to the reduced dimensionality. 2D materials’ widespread direct physical or chemical isolation techniques have been facilitated due to their intrinsic van der Waals layered morphology, whereas 3D close-packed bulk metals with isotropic bonding hinder their facile isolation in …

Onshore Power For The Docked Container Vessels In Apapa Port Through Blended Finance, Oladayo Matthew Atilola

World Maritime University Dissertations

No abstract provided.

Potential Roles Of Vessel Traffic Services (Vts) In Maritime Decarbonization, Suleiman Mustapha Bunza

World Maritime University Dissertations

No abstract provided.

Analysis Of The Pros And Cons Of The Acquisition Of Training Ships By Metis, Jeremiah Yaw Frimpong

World Maritime University Dissertations

No abstract provided.