Mechanical Engineering Commons^™

Study Of A Remote Wind Resource Assessment System Integrated With Internet Of Things, Filian Arbiyani, Filbert Filbert, Anthony Nathanael Theo

Journal of Mechanical Engineering Science and Technology (JMEST)

Wind energy is an emerging and popular source of clean energy due to its non-polluting nature and low cost. The efficient use of wind energy requires accurate and precise wind parameter measurements, which is where wind resource assessment (WRA) comes into play. The IoT and cloud-based systems have been applied to remote monitoring systems and provide crucial solutions for data acquisition, storage, and analytics in wind energy technology. This study aims to build a remote WRA system integrated with the Internet of Things. This study utilizes an Arduino Uno microcontroller, RK100-01 wind speed sensor, BMP280 temperature and pressure sensor, and …

Wind Turbine Power Phase Control With Dc Collection Bus For Onshore/Offshore Windfarms, Wayne Weaver, David Wilson, Rush Robinett

Michigan Tech Patents

A DC bus collection system for a wind farm reduces the overall required number of converters and minimizes the energy storage system requirements. The DC bus collection system implements a power phasing control method between wind turbines that filters the variations and improves power quality. The phasing control method takes advantage of a novel power packet network concept with nonlinear power flow control design techniques that guarantees both stable and enhanced dynamic performance.

Pyrolysis Kinetics Of Spirulina Platensis And Non-Condensable Gas Product Distribution In A Fixed-Bed Reactor, Ahmad Yusril Aminullah, Sukarni Sukarni, Retno Wulandari, Muhammad Shahbaz

Journal of Mechanical Engineering Science and Technology (JMEST)

Energy is a fundamental factor for civilization development and sustainability. However, energy sources are dominated by non-renewable fractions, such as fossil fuels. Renewable biomass is projected to be a future fuel source. Spirulina platensis (SP) has numerous advantages compared to other biomass, and it is considered 3rd generation biomass that does not interfere with food and land usage and has a relatively low main decomposition temperature at 325.7℃. Thermogravimetric analysis (TGA) was conducted to observe SP kinetics parameters, especially activation energy. Kissinger-Akahira-Sunose (KAS), Ozawa-Flynn-Wall (OFW), and Starink iso-conversional methods reveal that SP has an activation energy of 152.33, 154.56, and …

Tuning Of Real-Time Optimization Of Heliostat Concentrated Solar Power, Zachary L. Bernius

Mechanical Engineering ETDs

This paper investigates a real-time optimization algorithm for autonomously calibrating the heliostats in a concentrated solar power plant with the goal of maximizing power generation. The current state-of-the-art uses human operators to provide feedback for the heliostats. We use real-time/online measurements to produce an autonomous closed-loop system that does not require human intervention. The paper investigates tuning the gain of the real-time optimization algorithm to quickly and robustly converge to the optimal alignment and stabilize the system. The exponential stability of the system is certified using a quadratic Lyapunov function and static output feedback methods to couple the Lyapunov functions …

Simulation Of The Performance Of Kevlar Impregnated Shear Thickening Fluid Ballistic Test Results, Ridwan Prasetya, Andoko Andoko, Suprayitno Suprayitno

Journal of Mechanical Engineering Science and Technology (JMEST)

This study explores the enhancement of Kevlar fabric’s ballistic performance through impregnation with Shear Thickening Fluid (STF) for potential application in soft body armor. The experimental approach often fails to elucidate mechanical phenomena critical for the development of lightweight and high-strength body armor designs. To address this limitation, the finite element method, specifically using ANSYS/LS-DYNA R.13, was employed for a comprehensive analysis. The simulation aimed to evaluate the impact of STF on Kevlar fabric by assessing projectile velocity, force exerted by the projectile onto the fabric, displacement, stress distribution, and fabric failure mechanisms. Kevlar yarn was modeled as a shell …

The Role Of Sensing Modalities In Shaping Collective Motion And Group Behavior, Poorendra P. Ramlall

Doctoral Dissertations and Master's Theses

Collective behavior refers to the coordinated movements that emerge from simple interactions between individuals within a group. Traditionally, researchers have modeled these interactions assuming individuals can sense their surroundings in all directions, like having eyes all around their heads. While this is a useful simplification, it does not capture the diverse ways animals actually sense the world. In this thesis, we take inspiration from the natural world, particularly from animals like bats and dolphins that use a combination of hearing and sight to navigate their environments. We explore how combining these sensory cues in a three-dimensional space affects the way …

Experimental Study On The Effect Of Micro Concentrations Of Hybrid Nanofluids Through Microchannel Heat Sinks, Mohamed Salaheldin Elsherbiny, Moustafa Ali, Moatsem Shahin, Mahmoud El-Kady

Renewable Mechanical Energy

The current study examines the convective heat transfer coefficient experimentally. It assesses the performance of Al2O3, CuO, ZnO, and Ag/ distilled water nanofluids up to a tetra level of hybridization utilized in microprocessor cooling systems equipped with MCHS. An equal ratio of 50%, 33.3%, and 25% for di-, tri-, and tetra-nanofluids, respectively, with a focus on micro-volume fraction 0.025% and comparing it with 0.05%. Operating conditions were as follows: heat loading from 136.4 up to 196.4 watts; and flow rate from 0.35 up to 0.5 LPM. The findings showed that all types of mono nanofluids showed an increase in Nu …

The Effect Of Tio2 On The Electrochemical Performance Of Sb2o3 Anodes For Li-Ion Batteries, Kithzia Gomez, Elizabeth M. Fletes, Jason Parsons, Mataz Alcoutlabi

Mechanical Engineering Faculty Publications

Antimony (Sb) and its composites have been recognized as potentially good anode materials for lithium-ion batteries (LIBs) due to their relatively high theoretical capacity of 660 mAh g−1 and to their low cost. However, Sb-based anodes suffer from a high-volume change during the lithiation/delithiation process that results in capacity fading and anode degradation after prolonged charge/discharge cycles. To address this issue, Sb2O3/TiO2 nanocomposite electrodes can be synthesized and used as anodes for LIBs with high capacity and good electrochemical stability. In the present work, TiO2@Sb2O3 composites with different (TiO2:Sb2O3) ratios of 0:1, 1:1, 1:4 and 3:1 were synthesized and directly …

Improving Biomimetic Passive Dynamics Of A Quadruped Robot Hind Leg Hip Joint With A 3d Printed Torsion Spring, Haonan Zheng

Dissertations and Theses

The Agile and Adaptive Robotics Lab is interested in researching the neuromuscular control network of legged animal locomotion. To validate the lab's understanding of biological neural control, synthetic neural networks are developed and applied to biologically inspired legged robots. For a synthetic neural network to operate in the same manner as a biological neural network and produce the same locomotor behavior, the robot that the synthetic neural network is controlling must also mimic its biological counterpart. Previous research produced a quadruped robot hind leg designed with biomimetic passive dynamics by installing spring and damper pairs at each joint, however, an …

Rational Design Of Lignin-First Biorefineries Through Lignin Analysis And Deconstruction Modeling Tools, Aditya Ponukumati

McKelvey School of Engineering Graduate Student Theses & Dissertations

Lignocellulosic biomass is produced photosynthetically from atmospheric CO2 and is one of the few sources of renewable, reduced carbon that is generated on a scale comparable to demand for chemical commodities. For a sense of scale, the U.S. Energy Security and Independence Act targets the production of approximately 16 billion gallons per year of second-generation lignocellulosic biofuels by 2025. That production would generate approximately 62 million tons per year of dry lignin byproducts. The focus of this dissertation is on the valorization of these lignin components of biomass. Currently, lignin is either discarded or burned for local heat or electricity …

Enhancement Of Mechanical Properties Of Pcl/Pla/Dmso2 Composites For Bone Tissue Engineering, Kyung-Eun Min, Jae-Won Jang, Cheolhee Kim, Sung Yi

Mechanical and Materials Engineering Faculty Publications and Presentations

Bone tissue engineering shows potential for regenerating or replacing damaged bone tissues by utilizing biomaterials renowned for their biocompatibility and structural support capabilities. Among these biomaterials, polycaprolactone (PCL) and polylactic acid (PLA) have gained attention due to their biodegradability and versatile applications. However, challenges such as low degradation rates and poor mechanical properties limit their effectiveness. Dimethyl sulfone (DMSO₂) has emerged as a potential additive to address these limitations, offering benefits such as reduced viscosity, increased degradation time, and enhanced surface tension. In this study, we investigate tailored composites comprising PLA, PCL, and DMSO₂ to enhance mechanical …

Modeling Powder Spreadability In Powder-Based Processes Using The Discrete Element Method, Austin T. Sutton, M. Hossein Sehhat, Ming C. Leu, Joseph W. Newkirk

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Powder-bed fusion (PBF) processes refer to a subset of Additive Manufacturing (AM) techniques where powder is spread on the build-plate before melting (by a laser or electron beam). While PBF processes are attractive due to their ability for realizing complex structures that are either difficult or impossible to create through conventional means, the parts fabricated with these techniques can exhibit defects such as pores, inclusions, and excessive surface roughness. To minimize these defects, much research has been dedicated towards process maturation by optimizing laser or electron beam parameters. However, these developmental efforts typically do not address the recoating process where …

Me-Em Enewsbrief, June 2024, Department Of Mechanical Engineering- Engineering Mechanics, Michigan Technological University

Department of Mechanical and Aerospace Engineering eNewsBrief

No abstract provided.

A Survey On Fused Filament Fabrication To Produce Functionally Gradient Materials, Arup Dey, Monsuru Ramoni, Nita Yodo

Manufacturing & Industrial Engineering Faculty Publications

Fused filament fabrication (FFF) is a key extrusion-based additive manufacturing (AM) process for fabricating components from polymers and their composites. Functionally gradient materials (FGMs) exhibit spatially varying properties by modulating chemical compositions, microstructures, and design attributes, offering enhanced performance over homogeneous materials and conventional composites. These materials are pivotal in aerospace, automotive, and medical applications, where the optimization of weight, cost, and functional properties is critical. Conventional FGM manufacturing techniques are hindered by complexity, high costs, and limited precision. AM, particularly FFF, presents a promising alternative for FGM production, though its application is predominantly confined to research settings. This paper …

Sofast Cad Layout Tool, Felicia Brimigion

Mechanical Engineering ETDs

Concentrating solar mirrors need to have correct geometry to accurately focus sunlight onto a receiver. SOFAST is a tool created at Sandia National Laboratories which measures a mirror’s surface normal at a dense sampling of points, enabling evaluation of a given mirror’s expected performance. SOFAST supports general mirrors, including concentrating solar heliostats, troughs, and dishes. The examples presented in this report predominantly focus on heliostats.

There are generally four major components of a SOFAST system – the mirror, camera, projector, and screen. For SOFAST to properly measure a mirror, the following geometric constraints must be satisfied:

1. The reflection of …

Laser-Induced Electrochemical Biosensor Modified With Graphene-Based Ink For Label-Free Detection Of Alpha-Fetoprotein And 17Β-Estradiol, Ridma Tabassum, Pritu P. Sarkar, Ahmed Hasnain Jalal, Ali Ashraf, Nazmul Islam

Mechanical Engineering Faculty Publications

In this research, a novel electrochemical biosensor is proposed based on inducing graphene formation on polyimide substrate via laser engraving. Graphene polyaniline (G-PANI) conductive ink was synthesized by planetary mixing and applied to the working zone of the developed sensor to effectively enhance the electrical signals. The laser-induced graphene (LIG) sensor was used to detect alpha-fetoprotein (AFP) and 17β-Estradiol (E2) in the phosphate buffer saline (PBS) buffer and human serum. The electrochemical performance of the biosensor in determining these biomarkers was investigated by differential pulse voltammetry (DPV) and chronoamperometry (CA). In a buffer environment, alpha-fetoprotein (AFP) and 17β-Estradiol detection range …

Activity: Students Find Conceptual Errors In Ai Output, Janie Brennan

Generative AI Teaching Activities

Instructor asks ChatGPT questions related to a key concept to find one where ChatGPT has conceptual errors. Ask students to find the errors and explain them.

Corrigendum To “Evaluation Of Operational Performance Of Wusongkou Cruise Port Through Network Data Envelopment Analysis”

Journal of Marine Science and Technology–Taiwan

No abstract provided.

A Case Study On Optimizing Industrial Air Conditioning With Thermal Solar Energy In Egypt, Tamer Adel Mohamed, Hesham Safwat, Mohammed A. Ebaid

Mechanical Engineering

This study investigates the feasibility of implementing a solar-assisted adsorption chiller in an industrial building at the Oriental Weavers International factory located in 10th of Ramadan City, Cairo, Egypt. The objective is to replace an inefficient split air conditioning system currently used to cool the Jacquard units during carpet manufacturing. The research begins by analyzing the performance of the existing cooling system to establish a baseline. It then explores the potential energy savings achievable by replacing the current system with a solar-assisted adsorption chiller. The existing oversized boiler will serve as an auxiliary heater for the new system. TRNSYS simulation …

Synthesis, Characterization, And Antibacterial Activity Of Graphene Oxide/Zinc Hydroxide Nanocomposites, Jo Ann Sanchez, Luis A. Materon, Jason Parsons, Mataz Alcoutlabi

Mechanical Engineering Faculty Publications

Graphene and graphene oxide have shown good antibacterial activity against different bacterial species due to their unique physicochemical properties. Graphene oxide (GO) has been widely used to load metallic and metal oxide nanoparticles (NPs) to minimize their surface energy during processing and preparation, hence reducing their aggregation. In this work, GO was effectively synthesized and coated with different concentrations of zinc hydroxide Zn (OH)x using the precipitation method to prepare a GO/Zn (OH)x hybrid composite. The Zn (OH)x NPs and GO/Zn (OH)x nanocomposites were synthesized and characterized using various methods such as scanning electron microscopy (SEM), X-ray diffraction (XRD), and …

Developing And Testing Low-Cost Air Cleaners For Safer Spaces During Wildfires, Brett W. Stinson, Elliott T. Gall

Mechanical and Materials Engineering Faculty Publications and Presentations

Air cleaning reduces indoor exposure to fine particulate matter (PM2.5) during wildfire smoke events. However, resource and cost constraints may limit access to air cleaning during such an event, as both commercial devices and the higher-rated MERV filters that do-it-yourself (DIY) assemblies typically rely upon tend to be expensive and in short supply. With these constraints in mind, we developed and evaluated several configurations of a novel, DIY air cleaner that uses common household fabrics as filtration media. Clean air delivery rates (CADRs) of the devices were experimentally evaluated in two ways: first, with independent measurements of flowrates and single …

Direct Evaporative Cooling For Sustainability And Environmental Conservation, Hesham Safwat, Iman El-Mahallawi

Mechanical Engineering

This work presents the results of experimental work on cellulose cooling pads with honeycomb structure to study their evaporative cooling effect which is one of the partial solutions for achieving the SDG goals 2030. The paper outlines vari ous types of evaporative cooling materials, highlighting their distinctions and potential applications. Furthermore, it offers a comparative analysis of the cooling effects between wide hole and narrow hole cellulose cooling pads, both individually and in combination. The experimental setup results are thoroughly examined to provide insights into the performance of the cooling pads. Results showed up that direct evaporative cooling have a …

Analysis Of The Potential For Enhancing The Efficiency Of A Floating Photovoltaic (Fpv) System, How-Ping Wu, Ching-Yi Tseng, Chuan-Chung Jen, Yuan-Ching Chiang, Sih-Li Chen

Journal of Marine Science and Technology–Taiwan

This study examined the power generation capabilities of FPV systems and the advantages of employing active cooling on floating solar panels. Floating solar panels exhibit improved efficiency due to operating at lower temperatures facilitated by the cooling effect of water evaporation. Additionally, the high availability of water renders the application of the active cooling technique economically viable. This study developed a comprehensive simulation of a floating solar system, integrating a mathematical model to validate experimental findings and a temperature model derived from an energy equation specific to floating solar panels. This model calculates the heat transfer among the three different …

A Review On Machine Learning Implementation For Predicting And Optimizing The Mechanical Behaviour Of Laminated Fiber-Reinforced Polymer Composites, Sherif Sorour

Mechanical Engineering

The utilization of Machine Learning (ML) techniques in the analysis of the mechanical behavior of fiber-reinforced polymers (FRP) has been increasingly applied in composite materials. The ability to achieve high levels of accuracy, coupled with a reduction in computational cost once the ML models are trained, presents a powerful tool for optimization and in-depth analysis of laminated FRP. This review paper aims to provide insight into the emergence of this trend, offer an overview of various ML algorithms and related subtopics, and demonstrate different implementations of ML from recent studies with a specific focus on the design and optimization of …

Caring: Cannula For Alleviation Of Retinal Injury Caused By Needle Fluidic Gashing, Kaersti L. Rickels, Anthony L. Gunderman, Mattie S. Mclellan, Muhhamad M. Shamim, Joseph A. Sanford, Sami H. Uwaydat

Mechanical Engineering Faculty Publications and Presentations

Infusion-related iatrogenic retinal breaks (IRBs) are a significant complication in vitrectomies, particularly when smaller-gauge cannulas are used during fluid infusion. Using two-dimensional finite element analysis (FEA), we analyzed forces exerted on the retina from different cannulas: traditional 25-gauge, 20-gauge, 23-gauge, and 27-gauge, then investigated four alternative new cannula designs: (A) oblique orifices, (B) external obstruction, (C) side ports, and (D) perpendicular orifices. The analysis revealed that the standard 25-gauge cannula had a force of 0.546 milli-Newtons (mN). Optimized cannulas demonstrated decreased forces: 0.072 mN (A), 0.266 mN (B), 0.417 mN (C), and 0.117 mN (D). While all the designs decrease …

Vacuum Assisted Resin Transfer Method, Henry Allen

2024 Symposium

The vacuum assisted resin transfer method (VARTM) is a process used to make composite materials. This process is done using a mold or plate as a base and then building up the rest of the set up from there. On the base is the vacuum seal tape, spiral or percolated tubing, a connector for the tubing, the fiber plies in the center, separation layer, vacuum mesh, and the vacuum bag layer. This setup is then connected to the resin container. The other end is connected to a catch pot and vacuum pump. The purpose of the VARTM guided study was …

Investigating The Fatigue Life Of Asymmetric And Novel Helical Gear Drives, Rajesh S

Theses and Dissertations

The present research work investigates the contact and bending fatigue life of asymmetric helical gear and novel helical gear based on the finite element analysis. In the first phase, the contact and bending fatigue life of the asymmetric helical gear drives is estimated based on the strain life approach.

Further, a parametric study is carried out to investigate the influence of important helical gear parameters such as module, pressure angle, helix angle, gear ratio, teeth number and face width on contact and bending fatigue life of asymmetric helical gear drives. It is noted that the asymmetric helical gear shows a …

Performance And Enhancement Evaluation Of A Solar Still By Using Spraying Technology, Mahmoud Mohamed Dewedar, Yasser A. F. El-Samadony, Alsayed Alsaeed Mohamed, Ahmed Ibrahim Abdo

Journal of Engineering Research

The current experimental investigation uses the water spraying approach to increase the productivity and efficiency of pyramid solar still. The design, construction, and testing of a traditional and modified small-scale pyramid solar still were conducted under identical meteorological conditions as in Tanta City, Egypt (30° 47' N, 31°E). One of the modifications is that heated sheet metal will occasionally be sprayed with salted water. We looked into how the modified solar still's (MPSS) performance characteristics were affected by solar radiation, water depth, and sheet metal-specified temperature. Measurements were made of the saline water temperature, glass temperature, spraying flow rate, and …

Heat And Mass Transfer Characteristics During Vacuum Drying Of Wood, Mohamed Salah Elmetwaly, Lotfy Hassan Rabie Saker, Mohamed Sameh Salem

Journal of Engineering Research

The properties affecting the characteristics of heat and mass transfer during vacuum drying of wood are studied in this paper. The experimental work is carried out in 0.0365 m³ test rig vacuum dryer. The drying chamber dimensions are 0.5 m long and 0.305 m diameter carbon steel cylinder. This drying chamber is internally coated with epoxy paint, also this chamber is detachable closing caps at both ends meaning welded at one end and bolted at the other end to facilitate loading and unloading of the specimen. Two stainless steel heat exchanger plates with dimensions 0.3 m length, 0.15 m …

Electrospun Ibuprofen-Loaded Blend Pcl/Peo Fibers For Topical Drug Delivery Applications, Diala Bani Mustafa, Tsuyoshi Sakai, Osamu Sato, Mitsuo Ikebe, Shih-Feng Chou

Mechanical Engineering Faculty Publications and Presentations

Electrospun drug-eluting fibers have demonstrated potentials in topical drug delivery applications, where drug releases can be modulated by polymer fiber compositions. In this study, blend fibers of polycaprolactone (PCL) and polyethylene oxide (PEO) at various compositions were electrospun from 10 wt% of polymer solutions to encapsulate a model drug of ibuprofen (IBP). The results showed that the average polymer solution viscosities determined the electrospinning parameters and the resulting average fiber diameters. Increasing PEO contents in the blend PCL/PEO fibers decreased the average elastic moduli, the average tensile strength, and the average fracture strains, where IBP exhibited a plasticizing effect in …