Mechanical Engineering Commons^™

Me-Em Enewsbrief, December 2013, Department Of Mechanical Engineering-Engineering Mechanics, Michigan Technological University

Department of Mechanical and Aerospace Engineering eNewsBrief

No abstract provided.

Primary Resonance Behavior Of Expanded Polymer Cushion Material Under Low-Intensity Harmonic Excitations, Gregory Batt

All Dissertations

The demand to lower costs and reduce the amount of packaging materials utilized in a packaged-product system has placed increased importance on the development of tools to model the behavior of packaging systems. In this dissertation, the free and forced vibration response of a nonlinear, distributed-parameter model of a viscoelastic rod with an applied tip-mass is used to investigate the response of expanded polymer cushion materials to low-intensity harmonic excitations. The rod and tip-mass represent an idealized packaged product system. A nonlinear model is developed from constitutive relations. A classical Maxwell-Weichert model, represented via a Prony series, is used to …

Mode I Fracture Toughness Of Eight-Harness-Satin Carbon Cloth Weaves For Co-Cured And Post-Bonded Laminates, Josh E. Smith

Master's Theses

Mode I interlaminar fracture of 3k 8-Harness-Satin Carbon cloth, with identical fill and weft yarns, pre-impregnated with Newport 307 resin was investigated through the DCB test (ASTM D5528). Crack propagations along both the fill and weft yarns were considered for both post-bonded (co-bonded) and co-cured laminates. A patent-pending delamination insertion method was compared to the standard Teflon film option to assess its applicability to mode I fracture testing. The Modified Beam Theory, Compliance Calibration method, and Modified Compliance Calibration method were used for comparative purposes for these investigations and to evaluate the validity of the proposed Equivalent Stiffness (EQS) method. …

Thermal Analysis Of Carbon Nanofiber Reinforced Isotactic Polypropylene, Anna Alicia Hernandez

Theses and Dissertations - UTB/UTPA

Isotactic Polypropylene (IPP) is a commonly known thermoplastic that has unique properties include being light weight, high performance, impact strength, tensile strength, elongation, and high temperature properties. The use of vapor grown carbon nanofiber (VGCNF) reinforcements on polypropylene has shown to produce high specific modulus, strength, electrical and thermal properties on specimens. Thermogravimetric (TGA) investigations on the thermal degradation of isotactic polypropylene – vapor grown carbon nanofibers composites in nitrogen were reported. The mass evolution as a function of temperature is a single sigmoid for both polypropylene and polypropylene loaded with VGCNF. The inflection temperature of these sigmoids increases as …

Understanding The Role Of Requirements In Engineering Design By Novices, Shraddha Joshi

All Dissertations

Requirements play a critical role in the design process. The broader impact of this research is to develop a systematic understanding of the current use of requirements with an ultimate goal to develop guidelines and recommendations for more effective use of requirements throughout the design process. Thus, this research begins to answer the question about what is the role of requirements in design process and, specifically, its role in idea generation? The answer to this question is explored in three phases. The first phase is to understand how requirements are currently taught to students. To that end, two surveys were …

Development Of A Coupled Fluid And Colloidall Particle Transport Model, Scott Ripplinger

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

A colloidal system usually refers to when very small particles are suspended within a solution. The study of these systems encompasses a variety of cases including bacteria in ground water, blood cells and platelets in blood plasma, and river silt transport. Taking a look at these kinds of systems using computer simulation can provide a great deal of insight into how they work. Most approaches to date do not look at the details of the system, however, and are specific to given system. In this study a program called OpenFOAM is used as a basis to build a computer simulation …

Wind Tunnel Testing And Numerical Simulation On Aerodynamic Performance Of A Three Bladed Savonius Wind Turbine, Khandakar Niaz Morshed, Mosfequr Rahman, Gustavo Molina, Mahbub Ahmed

Mechanical Engineering: Faculty Publications

The purpose of this research work is to investigate experimentally and computationally the feasibility of improving the performance of the vertical-axis Savonius wind turbine. The authors first performed a series of wind tunnel investigations on semi-cylindrical three-bladed Savonius rotor scale models with different overlap ratios and without overlap. These experiments were conducted in front of a low-speed subsonic wind tunnel at different Reynolds numbers. Pressures around the concave and convex surfaces of each blade, as well as the static torque for the rotor models, were measured. Using these experimental data, the authors calculated aerodynamic characteristics such as drag coefficients, static …

Heat Transfer Experiment: Energy Conservation, Ben Ward, Brett Wallace, Ryan Waltman

Mechanical Engineering

This proposal, prepared for the Mechanical Engineering Department by the HTEC design team will redesign and replace the current energy conversion lab that is inaccurate and out of date. The team will evaluate methods of energy conversion, specifically using braking systems, as well as existing labs in order to design an accurate and relatable experiment for this lab. The project team will work with Professor Kim Shollenberger in order to design an experiment that demonstrates energy conversion through the first law of thermodynamics while utilizing a common device that is practical in student’s lives. The final result of this project …

Automated Foosball Table Year 1: Final Project Report, Juan David Gutierrez-Franco, John Inlow, Jesse Graham, Larry Huang

Mechanical Engineering

This project is a first iteration of an automated foosball table designed and created using servomotors provided by Yaskawa to create an interactive tradeshow display where guests can play against the algorithms developed in the PLC (programmable logic controller) controlling the servomotors. There will be a second iteration of the project done by a different team directly following this one. The motion components were selected with the intent to be able to surpass the reaction times and speeds of expert human players. There are a total of eight servomotors, four controlling linear actuators for translation of rods, and four controlling …

Prototype Device For The Detection Of Subsurface Peach Pit Fragments, Colby Lippincott, Hamilton Little, Rick Hayes, Elliot Wenzel

Mechanical Engineering

Peach pits can break during processing into several small fragments and are difficult to see and remove from the peach. Wawona Frozen Foods is asking for a fully designed, built and tested prototype that can detect these pit fragments with ease and speed. Our design uses an array of needles that puncture into a peach half. A pressure sensor measures the force on the needles and determines whether or not each needle hit the peach flesh or a pit fragment. The array of needles consists of 313 needles each with a diameter of 0.6 mm with a total array diameter …

Kolsky Bar Experiment For High-Rate Large Deformations Of Polycarbonate, Jason Gerald Vogeler

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

Polycarbonate (PC) is a tough, transparent engineering thermoplastic. Its impact strength and ability undergo large plastic deformations without shatter make PC an ideal protective material for impact-resilient eyewear, aircraft windows and transparent armor. A good understanding of the response of this material to large deformations at high strain rates is critical for its utilization in these applications. To this end, a striker-less Kolsky bar device is employed in this work for the needed material characterization. The apparatus allow impulsive torsion and/or compression loadings with pulse durations sufficiently long for the plastic flow behavior to develop fully. Three new testing techniques …

Computer-Based Stereoscopic Parts Recognition For Robotic Applications, Ahmad A. Fayed

UNLV Theses, Dissertations, Professional Papers, and Capstones

Most of robotic handling and assembly operations are based on sensors such as range and touch sensors. In certain circumstances, such as in the presence of ionizing radiation where most customary sensors will degrade over time due to radiation exposure, these sensors won't function properly. Utilizing two or more cameras (stereo vision) located outside the target zone and analyzing their images to identify location and dimensions of parts within the robot workspace is an alternative for using sensors. Object Recognition is affected by the light condition which oftentimes causes the gray-scale or red, green, and blue values to have a …

Experimental And Finite Element Studies Of Shock Transmission, Eldon Jerry Goddard

UNLV Theses, Dissertations, Professional Papers, and Capstones

Composite materials are more widely used today in engineering products than ever before. Shock transmission in jointed composite sections needs to be investigated to understand the affect of composite materials on the dynamic response of the system. There exists limited published work on transient shock propagation through composite sections. The aim of this study is to analyze the transient behavior of joints in composite materials subjected to low impact loads and to develop a computational model that provides an improved physics based shock model. The jointed connection will be investigated experimentally and using Finite Element Analysis (FEA). The bolted joint …

Improving Global Impact: How The Integration Of Remotely Reporting Sensors In Water Projects May Demonstrate And Enhance Positive Change, Evan A. Thomas

Mechanical and Materials Engineering Faculty Publications and Presentations

This article argues that improved feedback on the actual impact of development programs may ensure the success of poverty reduction interventions such as water filters, water pumps, latrines, and cookstoves.

Development Of A Hybrid Vehicle Powertrain Test Laboratory, Bennet Samuel Soundarraj

Doctoral Dissertations and Master's Theses

During the last two years, Embry-Riddle Aeronautical University has installed and tested a fully functional eddy-current chassis dynamometer testing facility on campus. An automotive test facility requires a systems engineering approach to install, calibrate and commission a chassis dynamometer. This thesis shows that, the dynamometer test facility was successfully installed, commissioned and documented to safely support the power train development and testing. We can currently test the EcoCAR vehicle and a number of other front-wheel-drive vehicles at our university campus using the eddy current chassis dynamometer.

Pvcrov : An Experimental Platform For Multi-Robot Control Systems, Nicholas Prince, Gregory Roos, Jennifer Semones, Chase Traficanti

Mechanical Engineering Senior Theses

As the field of multi-robot control systems grows, the demand for flexible, robust and precise multi-robot testbeds increases. Up to this point, the testbeds that do exist for testing multi-robot controllers are often expensive, hard to deploy, and typically constrained to a single plane of motion. These constraints limit the capacity to conduct research which is why team Autonomously Controlled Electromechanical Systems (ACES) has created the PVCROV system. PVCROV is a low cost, underwater platform for testing multi-robot control systems. By utilizing an underwater environment, ACES created a testbed that is not constrained to a single plane of motion. Additionally, …

Liquid Phase Stability Under An Extreme Temperature Gradient, Zhi Liang, Kiran Sasikumar, Pawel Keblinski

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Using Nonequilibrium Molecular Dynamics Simulations, We Subject Bulk Liquid to a Very High-Temperature Gradient and Observe a Stable Liquid Phase with a Local Temperature Well above the Boiling Point. Also, under This High-Temperature Gradient, the Vapor Phase Exhibits Condensation into a Liquid at a Temperature Higher Than the Saturation Temperature, Indicating that the Observed Liquid Stability is Not Caused by Nucleation Barrier Kinetics. We Show that, Assuming Local Thermal Equilibrium, the Phase Change Can Be Understood from the Thermodynamic Analysis. the Observed Elevation of the Boiling Point is Associated with the Interplay between the "Bulk" Driving Force for the Phase …

Investigation Of Thermal Cycle And Hardness Distribution In The Laser Cladding Of Aisi H13 Tool Steel Produced By A High Power Direct Diode Laser, Parisa Farahmand, Prabu Balu, Fanrong Kong, Radovan Kovacevic

Mechanical Engineering Research

Laser cladding (LC) of tool steel has significant application in rapid tooling, and surface coating for worn-out components in different industries. During the LC process, several phase transformations influence the microstructural and mechanical properties of the deposited layer. In order to successfully implement the LC process, it is essential to understand the relationship between the thermal cycle (heating and cooling), phase transformations, and the output quantities of the deposited layer. In this study a direct diode laser with a power of up to 8 kW was used to deposit AISI H13 tool steel on mild steel grade A36 substrate to …

Mechanical Engineering News, Georgia Southern University

Mechanical Engineering: News & Publications (2013-2023)

• Accepting Applications for National Science Foundation: Research Experience for Undergraduates

Ergonomichandle And Articulating Laparoscopictool, M. Susan Hallbeck, Dmitry Oleynikov, Kathryn Done, Tim Judkins, Allison Dimartino, Jonathan Morse, Lawton N. Verner

Department of Mechanical and Materials Engineering: Faculty Publications

The present invention relates to a laparoscopic apparatus. The apparatus includes a handle having a body portion, a top surface, opposite bottom surface, a proximal and distal end. The top surface of the base is contoured to compliment the natural curve of the palm. The apparatus further includes a shaft projecting from the distal end of the handle. The shaft has a proximal and distal end. A control sphere is located on the handle. The control sphere can be moved by one or more of a user's fingers to indicate direction. An end effector is located at the distal end …

Wax Pattern Shrinkage Project Summary, David Bishop, Perry Carter

Journal of Undergraduate Research

Purpose: The purpose of this project was to better understand the sources of variation that influence the shrinkage of wax patterns in investment casting. With a better understanding of the variation, manufacturers will be able to produce parts that have more precise dimensions.

Cad Tools For Thermal Growth Research, C. Porter Bassett, Dr. C. Greg Jensen

Journal of Undergraduate Research

For my project I developed two tools to aid in manufacturing research that is currently being conducted in the Mechanical Engineering Department. This research is about milling, a type of manufacturing where metal is machined bye a spinning cutting tool, very similar to a drill bit, that cuts away the metal. This process generates a lot of heat and causes the cutting tool to heat up. When it heats up, it also expands and changes shape. The change in size of the cutting tool effects how much metal it removes. In precision work, this change in shape can be enough …

Strain In Polysilicon Microbeams: The Relationship Between Beam Geometry And The Nominal Strain At Failure, Susan Norma, Candland Bromley, Dr. Larry L. Howell

Journal of Undergraduate Research

The objective of this research was to investigate the stress and strain behavior of microscopic cantilevered polycrystallin silicon (polysilicon) beams. A knowledge of this behavior is necessary to accomplish reliable mechanical design of micro-electro-mechanical systems (MEMS).

Oil Droplet Behavior At A Pore Entrance In The Presence Of Crossflow: Implications For Microfiltration Of Oil-Water Dispersions, Nikolai V. Priezjev, Tohid Darvishzadeh, Volodymyr V. Taravara

Mechanical and Materials Engineering Faculty Publications

The behavior of an oil droplet pinned at the entrance of a micropore and subject to clossflow-induced shear is investigated numerically by solving the Navier-Stokes equation. We found that in the absence of crossflow, the critical transmembrane pressure required to force the droplet into the pore is in excellent agreement with a theoretical prediction based on the Young-Laplace equation. With increasing shear rate, the critical pressure of permeation increases, and at sufficiently high shear rates the oil droplet breaks up into two segments. The results of numerical simulations indicate that droplet breakup at the pore entrance is facilitated at lower …

Simulation Of Vertical Axis Wind Turbines With Variable Pitch Foils, L. Damon Woods, John F. Gardner, Kurt S. Myers

Mechanical and Biomedical Engineering Faculty Publications and Presentations

A dynamic computer model of a turbine was developed in MATLAB in order to study the behavior of vertical axis wind turbines (VAWTs) with variable pitch (articulating) foils. The simulation results corroborated the findings of several empirical studies on VAWTs. The model was used to analyze theories of pitch articulation and to inform the discussion on turbine design. Simulations of various models showed that pitch articulation allowed Darrieus-style vertical axis wind turbines to start from rest. Once in motion, the rotor was found to accelerate rapidly to very high rotational velocities. The simulations revealed a plateau region of high efficiency …

Developing An Architecture Framework For Cloud-Based, Multi-User, Finite Element Pre-Processing, Jared Calvin Briggs

Theses and Dissertations

This research proposes an architecture for a cloud-based, multi-user FEA pre-processing system, where multiple engineers can access and operate on the same model in a parallel environment. A prototype is discussed and tested, the results of which show that a multi-user preprocessor, where all computing is done on a central server that is hosted on a high performance system, provides significant benefits to the analysis team. These benefits include a shortened preprocessing time, and potentially higher-quality models.

An Investigation Into The Mechanisms Of Formation Of The Hard Zone In Fsw X65, Jacob D. Allred

Theses and Dissertations

Friction stir welding (FSW) of HSLA steel commonly produces a hard zone (HZ) on the advancing side (AS) of the weld. Despite its detrimental effects on weld toughness, the mechanisms of its formation have not been thoroughly investigated and are not well understood. This paper investigates the various mechanisms in FSW believed to affect the weld HZ, namely: strain, strain-rate, peak temperature and cooling rate. Gleeble tests indicate that strain and strain rate have negligible effects on weld HZ with cooling rate and peak temperature as dominant effects. Jominy tests resulted in cooling rate having 270% greater influence than peak …

Artificial Intelligent Metallurgical Grain Detection, Adarsh Kesireddy

Mechanical Engineering Theses

In recent years, image processing has been applied to metallurgy but its applications were mainly confined to iron. This research instead focuses on recognizing phases present in steel. Phase recognition is very important because it aids in specifying the properties of steel specimens. This research is concentrated on recognizing Pearlite, Ferrite, Martensite and Cementite present in steel. A neural network was used to recognize these four phases. For a neural network to recognize any object it requires input values called features. This research introduces a combination of features which were not used before: texture based features of entropy, energy, contrast, …

Trajectory Generation And Optimization For Experimental Investigation Of Flapping Flight, Michael Schnebly Wilcox

Theses and Dissertations

Though still in relative infancy, the field of flapping flight has potential to have a far-reaching impact on human life. Nature presents a myriad of examples of successful uses of this locomotion. Human efforts in flapping flight have seen substantial improvement in recent times. Wing kinematics are a key aspect of this study. This study summarizes previous wing trajectory generators and presents a new trajectory generation method built upon previous methods. This includes a novel means of commanding unequal half-stroke durations subject to robotic trajectory continuity requirements. Additionally, previous optimization methods are improved upon. Experimental optimization is performed using the …

Energy Analysis & Utility Cost Mitigation With Storage For Commercial Buildings In California, Eric Anthony Fleming

LMU Theses and Dissertations

While on a great precipice of emerging energy technologies, it is necessary to understand how these technologies are most effectively integrated into current end-user systems. At the moment,

36% of California’s energy consumption is demanded from the commercial buildings sector. This report investigates the nature of energy with the state of California through various sources and analysis techniques. Using specific weather and commercial building data, this paper also focuses on the analysis of Commercial Building energy demand modeling for the state’s sixteen weather zones. It is modeled using the Department of Energy’s tool: EnergyPlus and analysis is performed with R …