Mechanical Engineering Commons^™

Novel Nanostructured Titania And Titania Nanocomposites For Photovoltaics And Photocatalysis, Xinning Luan

LSU Doctoral Dissertations

With the consumption of energy continually increasing around the world and the main source of this energy, fossil fuels, slowly being depleted, the need for alternate sources of energy is becoming more and more pertinent. Demand for solar energy has experienced exponential increase over the last decade. Nanostructured TiO2 has attracted significant attention due to its nontoxicity, low cost and wide applications in photovoltaics and photocatalysis. This research is focused on novel synthesis and surface modification of TiO2 nanotube arrays for applications in advanced dye-sensitized solar cells (DSSCs) and efficient photocatalysis. The first part of this work entails fast synthesis …

Energy And Thermodynamically Based Approaches For Analysis Of Damage In Contact Problems, Afshin Babaie Aghdam

LSU Doctoral Dissertations

A novel methodology for analysis of damage in contact problems in presented. Two important categories of contact damage are studied, namely crack nucleation and adhesive wear. The proposed methodology is primarily based on the laws of energy and thermodynamics, and as such offers great advantages by unifying the analysis of damage in a variety of contact configurations. Crack nucleation is the first damage type analyzed. For this purpose, the line-contact fretting configuration is chosen. A thermodynamically-based continuum damage mechanics (CDM) approach is employed. Intense stress gradients in the contact region are found to be highly influential in the crack nucleation …

Innovative Heat Transfer Augmentation Techniques In Mechanical Face Seal, Nian Xiao

LSU Doctoral Dissertations

Excessive heat generated at the face seal contact interface has been recognized as one of main causes of failure of mechanical seals. In the past few decades various efforts have been attempted to remove heat from the contact interface uniformly in order to reduce the interfacial temperature, eliminate thermally-induced failure, and thus increase the life of a mechanical seal. Two innovative heat transfer augmentation techniques - surface texturing and built-in phase change device - have been developed in our laboratory to effectively enhance the heat transfer in mechanical face seal. Surface texturing can increase the surface area, change the near …

Magnetic Nanoparticles For Thermally Anoparticles Enhanced Heavy Oil Recovery, Hazem Elshorbagy Elshorbagy

Theses

A novel method of delivering thermal energy efficiently to reservoirs for heavy oil production is described in this study. The method uses magnetic nanoparticles that generate heat locally when exposed to a high frequency magnetic field oscillation via hysteresis losses. This concept is currently used in medical research to thermally kill cancerous cells. Electromagnetic heating is a n alternative method to heat heavy oil reservoirs without using water or steam. Using magnetic nanoparticles with electromagnetic heating would greatly reduce the energy requirement and would allow efficient propagation of heat into deeper regions beyond wellbore locality that are otherwise difficult to …

Predictive Modeling Of Coupled Multi-Physics Systems: Ii. Illustrative Application To Reactor Physics, Dan Gabriel Cacuci, Madalina Corina Badea

Faculty Publications

This work presents paradigm applications to reactor physics of the innovative mathematical methodology for "predictive modeling of coupled multi-physics systems (PMCMPS)" developed by Cacuci (2014). This methodology enables the assimilation of experimental and computational information and computes optimally predicted responses and model parameters with reduced predicted uncertainties, taking fully into account the coupling terms between the multi-physics systems, but using only the computational resources that would be needed to perform predictive modeling on each system separately. The paradigm examples presented in this work are based on a simple neutron diffusion model, chosen so as to enable closed-form solutions with clear …

Ni-Doped Sr2Fe1.5Mo0.5O6-Δ As Anode Materials For Solid Oxide Fuel Cells, Guoliang Xiao, Siwei Wang, Ye Lin, Zhibin Yang, Minfang Han, Fanglin Chen

Faculty Publications

10% Ni-doped Sr₂Fe_1.5Mo_0.5O_6-δ with A-site deficiency is prepared to induce in situ precipitation of B-site metals under anode conditions in solid oxide fuel cells. XRD, SEM and TEM results show that a significant amount of nano-sized Ni-Fe alloy metal phase has precipitated out from Sr_1.9Fe_1.4Ni_0.1Mo_0.5O_6-δ upon reduction at 800^◦C in H₂. The conductivity of the reduced composite reaches 29 S cm⁻¹ at 800^◦C in H₂. Furthermore, fuel cell performance of the composite anode Sr_{1.9 …}

Modeling Of Chemical-Mechanical Couplings In Anode-Supported Solid Oxide Fuel Cells And Reliability Analysis, Xinfang Jin, Xingjian Xue

Faculty Publications

Oxygen ionic transport in conducting ceramics is an important mechanism enabling solid oxide fuel cell (SOFC) technology. The multi-physicochemical processes lead to the fact that the distribution of oxygen vacancy site fraction is not uniform in a positive-electrode electrolyte negative-electrode (PEN) assembly. Different oxygen vacancy concentrations induce different volumetric expansion of ceramics, resulting in complicated chemical–mechanical coupling phenomena and chemical stress in SOFCs. In this research, a mathematical model is developed to study oxygen ionic transport induced chemical stress in an SOFC. The model is validated using experimental polarization curves. Comprehensive simulations are performed to investigate chemical stress distribution in …

A Platinum Nanowire Network As A Highly Effective Current Collector For Intermediate Temperature Solid Oxide Fuel Cells, Hanping Ding, Xingjian Xue

Faculty Publications

We report the fabrication and evaluation of a platinum nanowire network as a highly efficient current collector for solid oxide fuel cells (SOFCs). The ink of carbon-black supported platinum nanoparticles was sprayed onto the cathode. After firing, the carbon black was oxidized and disappeared as carbon dioxide gas while the platinum nanoparticles connect with one another, forming a tree-branch-like nanowire network. The diameters of the nanowires range from 100 nm to 400 nm. Compared to a conventional platinum paste current collector, the polarization resistance of the PrBaCo₂O_5+δ (PBCO) cathode with a nanowire current collector was reduced …

Low Frequency Energy Scavenging Using Sub-Wave Length Scale Acousto-Elastic Metamaterial, Raiz U. Ahmed, Sourav Banerjee

Faculty Publications

This letter presents the possibility of energy scavenging (ES) utilizing the physics of acousto-elastic metamaterial (AEMM) at low frequencies (<∼3KHz). It is proposed to use the AEMM in a dual mode (Acoustic Filter and Energy Harvester), simultaneously. AEMM’s are typically reported for filtering acoustic waves by trapping or guiding the acoustic energy, whereas this letter shows that the dynamic energy trapped inside the soft constituent (matrix) ofmetamaterials can be significantly harvested by strategically embedding piezoelectric wafers in the matrix. With unit cell AEMM model, we experimentally asserted that at lower acoustic frequencies (< ∼3 KHz), maximum power in the micro Watts (∼35µW) range can be generated, whereas, recently reported phononic crystal based metamaterials harvested only nano Watt (∼30nW) power against 10KΩ resistive load. Efficient energy scavengers at low acoustic frequencies are almost absent due to large required size relevant to the acoustic wavelength. Here we report sub wave length scale energy scavengers utilizing the coupled physics of local, structural and matrix resonances. Upon validation of the argument through analytical, numerical and experimental studies, a multi-frequency energy scavenger (ES) with multi-cellmodel is designed with varying geometrical properties capable of scavenging energy (power output from ∼10µW – ∼90µW) between 0.2 KHz and 1.5 KHz acoustic frequencies.

There Can Be Turbulence In Microfluidics At Low Reynolds Number, Guiren Wang, F. Yang, Wei Zhao

Faculty Publications

Turbulence is commonly viewed as a type of macroflow, where the Reynolds number (Re) has to be sufficiently high. In microfluidics, when Re is below or on the order of 1 and fast mixing is required, so far only chaotic flow has been reported to enhance mixing based on previous publications since turbulence is believed not to be possible to generate in such a low Re microflow. There is even a lack of velocimeter that can measure turbulence in microchannels. In this work, we report a direct observation of the existence of turbulence in microfluidics with Re on the order …

Role Of Surface Chemistry In Nanoscale Electrokinetic Transport, Secuk Atalay

Mechanical & Aerospace Engineering Theses & Dissertations

This dissertation work presents the efforts to study the electrofluidics phenomena, with a focus on surface charge properties in nanoscale systems with the potential applications in imaging, energy conversion, ultrafiltration, DNA analysis/sequencing, DNA and protein transport, drug delivery, biological/chemical agent detection and micro/nano chip sensors.

Since the ion or molecular or particle transport and also liquid confinement in nano-structures are strongly dominated by the surface charge properties, in regards of the fundamental understanding of electrofluidics at nanoscale, we have used surface charge chemistry properties based on 2-pK charging mechanism. Using this mechanism, we theoretically and analytically showed the surface charge …

Numerical Modeling Of Infrared Thermography Techniques Via Ansys, Hayder Abdulnabi Thajeel

Masters Theses

"Several inspection techniques have been developed over years. Recently, infrared thermography (IRT) technology has become a widely accepted as a nondestructive inspection (NDI) technique for different fields and various applications as well. Infrared thermography stands as one of the most an attractive and a successful NDI technique that has ability to detect the object's surface/subsurface defects remotely based on observing and measuring the surface's emitted infrared heat radiation by using an infrared camera. The finite element modeling FEM ANSYS was successfully used for the modelling of several IRT techniques; such as Pulsed Thermography (PT) and Lock-in Thermography (LT) that can …

Analysis Of Power Efficiency Of A Direct-Driven Locally Fabricated Permanent Magnet Ac Generator For Small-Scale Wind Power Applications In Tanzania, Mussa Iddi Mgwatu Dr.

Tanzania Journal of Engineering and Technology (TJET)

The use of direct-driven permanent magnet alternating current (AC) generators offers the opportunity to reduced costs and increased system efficiency. This type of generator could be the best alternative for rural population whom are not connected to the national grid. To improve the design and efficiency of locally fabricated generators, it is imperative to characterize both their mechanical and electrical parameters. This paper presents the analysis of power efficiency of the synchronous permanent AC generator locally fabricated in Tanzania. In this case, load resistance and rotational speed are characterized using designed experiment. The output current and voltage of the generator …

Thermolysis And Kinetics Of Scrap Tyre And Bagasse For Energy Utilization, Petro Ndalila

Tanzania Journal of Engineering and Technology (TJET)

The increase of energy demand has brought concern to find alternative fuel that will at least sustain the requirement. Bagasse and scrap tyre are waste generated in our industrial activities, which can be used in energy production to subsidize the demand. This paper, aim to study the decomposition behaviour and kinetics of biomass (bagasse) and scrap tyre as preliminary stage of fuel sample analysis to be considered for energy production in gasification/combustion or pyrolysis facilities. The behaviour demonstrated with thermogravimetric analyzer (TGA), shows that all samples have high volatile amount release, 84.21% for bagasse and 85.08% for scrap tyre, which …

Mems Cantilever Sensor For Thz Photoacoustic Chemical Sensing And Spectroscopy, Nathan E. Glauvitz

Theses and Dissertations

Sensitive Microelectromechanical System (MEMS) cantilever designs were modeled, fabricated, and tested to measure the photoacoustic (PA) response of gasses to terahertz (THz) radiation. Surface and bulk micromachining technologies were employed to create the extremely sensitive devices that could detect very small changes in pressure. Fabricated devices were then tested in a custom made THz PA vacuum test chamber where the cantilever deflections caused by the photoacoustic effect were measured with a laser interferometer and iris beam clipped methods. The sensitive cantilever designs achieved a normalized noise equivalent absorption coefficient of 2.83x10^-10 cm^-1 W Hz^-1/2 using a 25 …

Rocket Motor Diagnostics Using Tunable Diode Laser Spectroscopy For Chemically Non-Reacting Air/Water Vapor Mixture In Internal Flow, Wesley Carleton

LSU New Orleans Theses and Dissertations

This research is for the implementation of non-intrusive measurement techniques in the study of high temperature pipe flow. A low pressure, laboratory scale hybrid rocket motor simulator was built to achieve high temperatures with various gases. A quartz test section was designed, built, and implemented into the existing test setup to accommodate the laser beam of the existing Tunable Diode Laser Absorption Spectrometer (TDLAS) system which was designed to observe water vapor. A super-heated water vapor injector was designed to obtain the desired water vapor concentrations. Flow characteristics were simultaneously recorded using the existing TDLAS system and the DAQ system …

A Wedge Impact Theory Used To Predict Bow Slamming Forces, Ashok Benjamin Basil Attumaly

LSU New Orleans Theses and Dissertations

The pressures and impact forces acting on a hull while experiencing bow wave slamming is analyzed using Vorus' Impact Theory. The theory extends the hydrodynamic analysis of planing hulls from simple wedges to irregular shapes using a Boundary Element Method. A Fortran-based code developed by the Author is used to analyze hullforms. Linear strip theory is used to extend the analysis over a three dimensional hull. Post-processing of output data gives hull pressure distributions at different time steps and is visually presentable.

Impact pressure, Impact force, Planing, Wave slamming, Bow impact, Vorus' theory, Boundary Element Method, Linear strip theory

Experimental Investigation Of Mist Film Cooling And Feasibility Study Of Mist Transport In Gas Turbines, Reda M. Ragab

LSU New Orleans Theses and Dissertations

In the modern advanced gas turbines, the turbine inlet temperature may exceed 1500°C as a requirement to increase power output and thermal efficiency. Therefore, it is imperative that the blades and vanes are cooled so they can withstand these extreme temperatures. Film cooling is a cooling technique widely used in high-performance gas turbines. However, the film cooling effectiveness has almost reached plateau, resulting in a bottleneck for continuous improvement of gas turbines' efficiency.

In this study, an innovative cooling scheme, mist film cooling is investigated through experiments. A small amount of tiny water droplets with an average diameter about 10-15 …

A Study On The Integration Of A Novel Absorption Chiller Into A Microscale Combined Cooling, Heating, And Power (Micro-Cchp) System, Scott J. Richard

LSU New Orleans Theses and Dissertations

This study explores the application of micro-CCHP systems that utilize a 30 kW gas microturbine and an absorption chiller. Engineering Equation Solver (EES) is used to model a novel single-effect and double-effect water-lithium bromide absorption chiller that integrates the heat recovery unit and cooling tower of a conventional CCHP system into the chiller’s design, reducing the cost and footprint of the system. The results of the EES model are used to perform heat and material balances for the micro-CCHP systems employing the novel integrated chillers, and energy budgets for these systems are developed. While the thermal performance of existing CCHP …

A Numerical Study Of High Temperature And High Velocity Gaseous Hydrogen Flow In A Cooling Channel Of A Ntr Core, Sajan B. Singh

LSU New Orleans Theses and Dissertations

Two mathematical models (a one and a three-dimensional) were adopted to study, numerically, the thermal hydrodynamic behavior of flow inside a single cooling channel of a Nuclear Thermal Rocket (NTR) engine. The first model assumes the flow in the cooling channel to be one-dimensional, unsteady, compressible, turbulent, and subsonic. The working fluid (GH₂) is assumed to be compressible. The governing equations of the 1-D model are discretized using a second order accurate finite difference scheme. Also, a commercial CFD code is used to study the same problem. Numerical experiments, using both codes, simulated the flow and heat transfer …

Buckling, Postbuckling And Imperfection Sensitivity Analysis Of Different Type Of Cylindrical Shells By Hui's Postbuckling Method, Hailan Xu

LSU New Orleans Theses and Dissertations

Hui and Chen (1986) were the first to show that the well-known Koiter’s General Theory of Elastic Stability of 1945 can be significantly improved by evaluating the postbuckling b coefficient at the actual applied load, rather than at the classical buckling load. Such improvement method was demonstrated to be (1) very simple to apply with no tedious algebra, (2) significant reduction in imperfection sensitivity and (3) although it is still asymptotically valid, there exists a significant extension of the range of validity involving larger imperfection amplitudes. Strictly speaking, Koiter’s theory of 1945 is valid only for vanishingly small imperfection amplitudes. …

Promoting Electrocatalytic Activity Of A Composite Sofc Cathode La0.8Sr0.2Mno3+Δ/Ce0.8Gd0.2O2-Δ With Molten Carbonates, Yunhui Gong, Xue Li, Lingling Zhang, Whitney Tharp, Changyong Qin, Kevin Huang

Faculty Publications

The effect of molten carbonates (MCs) on polarization resistance (R_P), a direct measure of oxygen reduction reaction (ORR) activity, of a composite La_0.8Sr_0.2MnO_3+δ/Ce_0.8Gd_0.2O_2-δ (LSM/GDC) solid oxide fuel cell (SOFC) cathode has been systematically investigated in this study over a temperature range of 550–650°C and partial pressure of oxygen (pO₂) span of 10⁻³ ∼ 1 atm. It is shown that the LSM/GDC cathode, either in the pristine or MC-modified states, can be generally modeled by two consecutive parallel circuits consisting of a resistance and a …

Fundamental Experimental Studies In Scaling, Blast Mitigation And Material Processing, Xing Zhao

Theses and Dissertations

In this work, two separate research efforts are discussed. They include experimental studies in (1) Scaling and Blast Mitigation and (2) Scaling in Friction Stir Extrusion. In both studies, the primary experimental measurement method is three-dimensional digital image correlation (3D-DIC), a non-contacting full-field measurement method that is applicable for both high-rate loading and quasi-static loading conditions.

Scaling and Blast Mitigation Studies:

A series of properly scaled structures was subjected to buried blast loading conditions via detonation of a small explosive buried in saturated sand. Using high speed stereo-vision systems to record the deformations of selected regions on the upper surface …

Applying Best Practices To Florida Local Government Retrofit Programs, Florida Solar Energy Center, Janet Mcilvaine

FSEC Energy Research Center®

In some communities, local government and non-profit entities have funds to purchase and renovate distressed, foreclosed homes for resale in the affordable housing market. Numerous opportunities to improve whole house energy efficiency are inherent in these comprehensive renovations. BA-PIRC worked together in a multiyear field study making recommendations in individual homes, meanwhile compiling improvement costs, projected energy savings, practical challenges, and labor force factors surrounding common energy-related renovation measures. The field study, Phase 1 of this research, resulted in a set of best practices appropriate to the current labor pool and market conditions in central Florida to achieve projected annual …

Effect Of Full-Annular Pressure Pulses On Axial Turbine Performance, Mark H. Fernelius

Theses and Dissertations

Pulse detonation engines show potential to increase the efficiency of conventional gas turbine engines if used in place of the steady combustor. However, since the interaction of pressure pulses with the turbine is not yet well understood, a rig was built to compare steady flow with pulsing flow. Compressed air is used in place of combustion gases and pressure pulses are created by rotating a ball valve with a motor. This work accomplishes two main objectives that are different from previous research in this area. First, steady flow through an axial turbine is compared with full annular pulsed flow closely …

An Experimental Analysis Of The Weighted Sum Of Spatial Gradients Minimization Quantity In Active Structural Acoustic Control Of Vibrating Plates, Daniel R. Hendricks

Theses and Dissertations

Active Structural Acoustic Control (ASAC) is a subcategory of the more widely known field of Active Noise control (ANC). ASAC is different from traditional ANC methods because it seeks to attenuate noise by altering the noise producing structure instead of altering the acoustic waves traveling through the air. The greatest challenge currently facing ASAC researchers is that a suitable parameter has not yet been discovered which can be easily implemented as the minimization quantity in the control algorithms. Many parameters have been tried but none effectively attenuate the sound radiation in a way that can be easily implemented. A new …

Computational And Experimental Study Of Degeneration, Damage And Failure In Biological Soft Tissues, Gregory Allen Von Forell

Theses and Dissertations

The purpose of this work was to analyze the biomechanics of degeneration, damage, and failure in biological soft tissues both experimentally and computationally to provide insight into tendon or ligament tearing, tendo-achilles lengthening and lumbar spine dysfunction. For soft tissue tearing, experimental studies for calculating fracture toughness were performed and determined that tendons and ligaments are able to completely resist tear propagation. For tendo-achilles lengthening, a damage model was developed to mimic the behavior of the lengthening that occurs as a result of the percutaneous triple hemisection technique. The model provided insight for predicting the amount of lengthening that occurs …

Active Structural Acoustic Control Of Clamped And Ribbed Plates, William Richard Johnson

Theses and Dissertations

A control metric, the weighted sum of spatial gradients (WSSG), has been developed for use in active structural acoustic control (ASAC). Previous development of WSSG [1] showed that it was an effective control metric on simply supported plates, while being simpler to measure than other control metrics, such as volume velocity. The purpose of the current work is to demonstrate that the previous research can be generalized to plates with a wider variety of boundary conditions and on less ideal plates. Two classes of plates have been considered: clamped flat plates, and ribbed plates. On clamped flat plates an analytical …

College Of Engineering Senior Design Competition Fall 2013, University Of Nevada, Las Vegas

Fred and Harriet Cox Senior Design Competition Projects

Part of every UNLV engineering student’s academic experience, the senior design project stimulates engineering innovation and entrepreneurship. Each student in their senior year chooses, plans, designs, and prototypes a product in this required element of the curriculum. A capstone to the student’s educational career, the senior design project encourages the student to use everything learned in the engineering program to create a practical, real world solution to an engineering challenge. The senior design competition helps focus the senior students in increasing the quality and potential for commercial application for their design projects. Judges from local industry evaluate the projects on …

Synthesis Of Tungsten Oxide Nanowires Onto Ito Glass Using T-Cvd, Tomy Abuzairi, Bohr-Ran Huang, Tzu-Ching Lin

Makara Journal of Technology

Tungsten oxide is an n-type semiconductor with interesting physical and chemical properties that make it suitable for various technological applications. Tungsten oxide nanowires were synthesized not only at low temperature but also without the use of any catalysts. The tungsten oxide nanowires were synthesized at 550 °C with tungsten layers onto the ITO glass using thermal chemical vapor deposition (T-CVD). The SEM image shows that the tungsten oxide nanowires are effectively grown with the 200 nm tungsten film. The Raman spectra shoulder at ~690 cm-1 proves the synthesized of tungsten oxide nanowires.