Mechanical Engineering Commons^™

An Experimental Investigation On Liquid Methane Convection And Boiling In Rocket Engine Cooling Channels, Abraham Trujillo

Open Access Theses & Dissertations

In the past decades, interest in developing hydrocarbon-fueled rocket engines for deep spaceflight missions has continued to grow. In particular, liquid methane (LCH4) has been of interest due to the weight efficiency, storage, and handling advantages it offers over several currently used propellants. Deep space exploration requires reusable, long life rocket engines. Due to the high temperatures reached during combustion, the life of an engine is significantly impacted by the cooling system's efficiency. Regenerative (regen) cooling is presented as a viable alternative to common cooling methods such as film and dump cooling since it provides improved engine efficiency. Due to …

Nanometric Structure-Property Relationship In Hafnium Oxide Thin Films Made By Sputter-Deposition, Mirella Vargas

Open Access Theses & Dissertations

Hafnium oxide (HfO2) is technologically an important material, which exhibits a unique set of properties such as a high dielectric constant (k~25) and wide band gap (~5.7 eV) which make this material attractive in the fields of microelectronics and optoelectronics. HfO2 has become the leading candidate to replace SiO2 dielectrics in gate oxides due to a higher permittivity and reportedly lower electron tunneling effects. HfO2 exhibits various polymorphs; the thermodynamic stability and phase existence depends on the temperature and pressure conditions. In addition, the controlled growth and manipulation of specific HfO2 crystal structures at the nanoscale dimensions is the driving …

Modeling And Simulation Of A Lead-Free Active Structural Fiber For Multifunctional Composites, Linda Vera

Open Access Theses & Dissertations

Piezoelectric materials are widely used in a many areas of science and technology due to their unique electromechanical properties. The transformation of mechanical energy into electrical energy and vice versa caused by the piezoelectric effect has led to the development of piezoelectric sensor devices and actuators used in accelerometers, pressure and vibration meters, micropositioning devices, ultrasound generators, structural health monitoring, etc.

The most used piezoelectric material to this day is lead zirconate titanate PbZrO3-PbTiO3 (PZT) because of its high piezoelectric coefficient and Curie temperature, which allows it to be used in a more wide variety of applications. However, the commercial …

The Interfacial Fracture Of Bonded Materials And Composites, Kai Zhao

Open Access Theses & Dissertations

Adhesive bonding and composite materials have been widely used in manufacturing industry. Failure results from the weakest link in a structure and this is often the interface between two materials. In case of composites, it becomes the fiber and matrix interface. In case of bonded polymers, the bonding line is the interface. This Dissertation is focused on the interfacial fracture of bonded materials and composites. First, a systematic experimental investigation on adhesive bonding strengths of polymer/polymer and polymer/metal joints was conducted and the experimental results were compared with other researchers' work. Then, a modified short-beam shear approach is developed to …

Development Of A Variable Stiffness Locally Adjustable And Repairable Low-Cost Energy Storage And Return Carbon Fiber Prosthetic Foot: A Feasibility Study, Joshua Scott Bowen

Open Access Theses & Dissertations

Background: Energy storage and return (ESAR) prosthetic feet were developed to improve the mobility and function of lower-limb amputees. Amputees in the Developing World amputees lack this technology. Most current Developing World prosthetic solutions do not adequately address the needs of active amputees and were not designed to pass international standard tests. Developing a low-cost, repairable, adjustable, energy storage and return prosthetic foot would close this technological gap and improve the mobility and function of active amputees. The goal of this research is to determine the feasibility of fabricating a low-cost, adjustable, ESAR, repairable prosthetic foot manufactured from carbon fiber …

Combustion Synthesis Of Molybdenum Silicides And Borosilicides For Ultrahigh-Temperature Structural Applications, Mohammad Shafiul Alam

Open Access Theses & Dissertations

Molybdenum silicides and borosilicides are promising structural materials for gas-turbine power plants. A major challenge, however, is to simultaneously achieve high oxidation resistance and acceptable mechanical properties at high temperatures. For example, molybdenum disilicide (MoSi₂) has excellent oxidation resistance and poor mechanical properties, while Mo-rich silicides such as Mo₅Si₃ (called T₁) have much better mechanical properties but poor oxidation resistance. One approach is based on the fabrication of MoSi₂−T₁ composites that combine high oxidation resistance of MoSi₂ and good mechanical properties of T₁. Another approach involves the …

Computationally Efficient Representation Of Statistically Described Material Microstructure For Tractable Forming Simulations, Nicholas Landry

Honors Theses and Capstones

The purpose of this project is to reduce a large statistical distribution of metal microstructure orientations to a manageable distribution to be used in metal forming simulations. Microstructure sensitive simulations at the macro-scale are impractical, because with so many state variables associated with material microstructure data, these simulations are extremely computationally expensive.

The goal was to develop a framework to accurately model plastic material response while representing the material microstructure in a more compact form, reducing 106 or more microstructure orientations to a significantly smaller statistical distribution of representative orientations. This will significantly increase the computational efficiency and make the …

Implementing Mechatronics Design Methodology In Mechanical Engineering Technology Senior Design Projects At The Old Dominion University, Vukica M. Jovanovic, Jennifer G. Michaeli, Otilia Popescu, Moustafa R. Moustafa, Mileta Tomovic, Alok K. Verma, Cheng Y. Lin

Engineering Technology Faculty Publications

In recent years, the nature of engineering design has changed due to advances in embedded system design and computer technologies. It is rare to engineer a purely mechanical design that does not incorporate electrical and electronic components. Mechanical engineers and mechanical engineering technologists must possess a multi-disciplinary knowledge with the understanding of both mechanical and electrical systems. For this purpose, undergraduate programs in engineering technology have added mechatronics courses to their curriculum. Mechatronics is a design process that is multi-disciplinary in nature and integrates principles of many engineering disciplines including, but not limited to, mechanical engineering, electrical engineering, and controls …

Design, Fabrication, And Properties Of 2-2 Connectivity Cement/Polymer Based Piezoelectric Composites With Varied Piezoelectric Phase Distribution, Xu Dongyu, Cheng Xin, Sourav Banerjee, Huang Shifeng

Faculty Publications

The laminated 2-2 connectivity cement/polymer based piezoelectric composites with variedpiezoelectric phase distribution were fabricated by employing Lead Zirconium Titanate ceramicas active phase, and mixture of cement powder, epoxy resin, and hardener as matrix phase with a mass proportion of 4:4:1. The dielectric, piezoelectric, and electromechanical coupling properties of the composites were studied. The composites with large total volume fraction ofpiezoelectric phase have large piezoelectric strain constant and relative permittivity, and thepiezoelectric and dielectric properties of the composites are independent of the dimensional variations of the piezoelectric ceramic layer. The composites with small total volume fraction of piezoelectric phase have large …

Composition Control Of Spinel Lithium Manganese Oxide For High Voltage, High Energy Lithium Ion Batteries, Hilary Eikhuemelo

LSU Master's Theses

In the quest for renewable source of energy, a remarkable step made was in the introduction of the battery system. The lithium ion battery was revolutionary in this regard particularly for its light weight and high energy density. There has been significant progress in the development of this battery system since the present form was introduced in the 1990s. There is currently a global dependence on the use of lithium ion battery in diverse applications such as in the electronics, communications and automobiles. Unfortunately, the energy obtainable from the lithium ion battery continuously falls behind the energy demand. This setback …

A Thermographic Method For Remaining Fatigue Life Prediction Of Welded Joints, Paul Thomas Williams

LSU Master's Theses

A non-destructive thermographic technique is adapted and applied to study the fatigue life and behavior of welded specimens made from two different materials. Results show good agreement between experimental predictions of consumed fatigue life and predicted fatigue life. Further, the thermal evolution of the specimens is used to calculate Damage Parameter, which is also used to make fatigue life predictions with promising results. To gain further insight Buckingham Pi theorem is also applied to determine the role of the important parameters involved in a dimensionless form. For this purpose, a series of experiments were performed and used for the analysis …

Fabrication And Enhancement Of Aluminum-Based Microchannel Devices, Paul Joseph Hymel

LSU Master's Theses

Microscale molding replication and transient liquid phase (TLP) bonding were used to fabricate Al-based microchannel heat exchangers (MHEs) and micro gas chromatograph (mGC) columns. Metal-based microchannel heat exchangers often experience corrosion as a result of their operating conditions. To address this problem, an internal anodization method was developed in Al microtubes by pulsing the flow of electrolyte through a microtube when the current dropped below a set value. The anodic aluminum oxide (AAO) films were characterized by scanning electron microscopy (SEM), focused ion beam (FIB) cross sections, and X-ray energy dispersive spectroscopy (EDS) to determine their growth rate and morphology. …

Using Eye-Tracking To Investigate Strategy And Performance Of Expert And Novice Control Room Operators, Christina Marie Koffskey

LSU Master's Theses

There is lacking research within the Petrochemical Industry that uses eye-tracking to explore the differences between the strategies of expert and novice control room operators as they monitor and address process parameters that could be used to improve novice training programs and interface design. Scan paths and three eye-tracking metrics (Fixation Frequency, Gaze Duration Mean, and Gaze Percentage) were used to investigate the differences in eye behavior of three expert control room operators and six novice students as they monitored and corrected a Crude Refinement simulation. A 2x2x2 mixed factor design was used to explore the effects that expertise (expert …

Minimization Of Transportation, Installation And Maintenance Operations Costs For Offshore Wind Turbines, Tasnim Ibn Faiz

LSU Master's Theses

Although it is a sustainable source and there is abundant potential for energy, cost of energy generated from offshore wind is still high compared to other sustainable energy sources. Apart from the manufacturing cost of turbines, cost of energy is significantly affected by costs of transportation and installation operations of wind turbines and maintenance operations of turbine components. Through optimum selection of decision variables, such as turbine installation method and rated power output of each turbine, cost of transportation and installation operations can be minimized. The first model in this study investigates the impact of these decision variables and effect …

An Experimental Investigation Of Corrosion Fatigue Life Via Thermographic Method, Richard Wayne Purvis

LSU Master's Theses

The effect of prior corrosion fatigue damage on the thermographic response of 1018 low carbon steel is investigated. Specimens were subject to rotating bending fatigue at 38 Hz loading frequency while being exposed to a 3.5% NaCl and distilled water solution. Some specimens were subject to corrosion fatigue for part of their fatigue life and then their thermographic response measured under fatigue in air at 62 Hz loading frequency. Fatigue tests in air with thermographic measurement were performed as a comparison. It was observed that the initial temperature rise after corrosion fatigue fits the previously proposed model for air fatigue, …

Analyses Of Online Monitoring Signals For A Gmaw Process Before And After Improvement, Aniruddha Joshi

LSU Master's Theses

The ability to detect the onset of welding instability is a very powerful tool in welding process monitoring and control. Toward this goal, this study investigates a gas metal arc welding (GMAW) process by analyzing online monitoring signals. Two separate data sets are obtained from the process, which correspond to (a) a stable process after improvement and (b) a relatively unstable process which tends to exhibit spatter and poor weld bead geometry. Voltage, current, wire-feeding speed and line speed signals for both data sets are analysed and features are extracted from the raw signals using different signal processing techniques. Specifically, …

Design And Development Of Scalable Solar Powered Water Purification Systems For Developing Nations, Shavin Pinto

Doctoral Dissertations and Master's Theses

This thesis presents the design and development of solar powered water purification systems. The systems were designed to meet specific customer requirements that were established from the experiences gained after the installation of five water purification systems in various Haitian communities. The systems are scalable and are able to supply 10,000-20,000 gallons of clean drinking water per day. The design consists of a three-stage filtration system with a disc-type sediment filter, a 0.1 micron ultrafiltration membrane, and an ultraviolet light for disinfection. The backwash cycle extends the life of the ultrafiltration membrane to 4-7 years before a new filter is …

Using A Sleep And Activity Monitor To Operationalize Fatigue Risk Management, Vanessa Bégat Seitz

LSU Master's Theses

When a person continues to work despite being fatigued, an accident may occur or productivity may decrease. Reducing fatigue related accidents is complicated due to the subjective nature and pervasiveness of the feeling of fatigue. Because finding one universal definition or measure of fatigue is problematic, fatigue is typically measured by a combination of factors such as amount of sleep obtained, physical or cognitive work performed, or sleepiness which can then be related back to a measure of performance. Until recently, sleep measurement was restricted to a lab setting; however, with the emergence of actigraph devices, it is now possible …

Assessing The Effects Of Work Zone Configurations On Drivers' Visual Attention, Karthy Punniaraj

LSU Master's Theses

This study assessed the effects of two different work zone configurations on driver’s visual attention by eye movement monitoring. A driving simulator study was conducted with thirty participants. Variations in traffic density and warning sign placement distance were added to the merge configurations to simulate the real time situation. A 2 x 2 x 3 within-subjects factorial design was used for this research. The independent variables used in this study were (1) merge configuration [(i) Conventional Lane Merge (CLM) and (ii) Joint Lane Merge (JLM)], (2) traffic density [(i) high and (ii) low] and (3) distance between traffic signs [(i) …

Influence Of Magnetic Fields On The Evaporation And Combustion Of A Single Droplet, Domingo Elias

LSU Master's Theses

The reliance on combustion as the primary source of energy will continue in the US for the next thirty years [1]. Experiments suggest that the use of magnetic fields can be one tool in the many-sided approach to the problem of environmental protection and energy conservation in the US. For instance, it is estimated that an increase in efficiency of 2% in spray combustion can save the US economy billions of dollars [2]. In this thesis I report on improving the quality of combustion through the use of magnetic fields. (1)I investigated the effects of magnetic fields on the evaporation …

Age, Performance And Retention Interval Effects On Acceptance Of A Consumer Health Information Technology System, Stephen Andrew Ford

LSU Master's Theses

The older adult population will continue to place pressure on the financial and resource allocation of the healthcare industry as the over 65 population continues to grow. Health care expenditures to treat the aging population will continue to rise as older adults are more likely to have expensive chronic conditions. The future may lay with Consumer Health Information Technology which may allow the patients to have more control of their treatment schedule and self-management of their health and chronic conditions. However, older adults may exhibit cognitive declines that prohibit the learning and proper use of technology, and this assumption is …

A Parametric Investigation Of A Novel, Modular, Gasketless, Microfluidic Interconnect Using Parallel Superhydrophobic Surfaces, Christopher Ramsey Brown

LSU Master's Theses

The gasketless microfluidic interconnect has the potential to offer a standardized approach to interconnects between modular microfluidic components. This strategy uses parallel superhydrophobic surfaces (contact angle ≥ 150ᴼ) to passively seal adjacent, concentric, microfluidic ports separated by an air gap using a liquid bridge created between the chips. The parallel superhydrophobic surfaces do not require the addition of a gasket or other additional components so that the assembly process scales favorably with an increasing number of fluidic interconnects. The gasketless seal does not contribute to geometric constraint between the component chips which allows alignment between chips to scale favorably with …

Material Synthesis And Fabrication Method Development For Intermediate Temperature Solid Oxide Fuel Cells, Hanping Ding

Theses and Dissertations

Solid oxide fuel cells (SOFCs) are operated in high temperature conditions (750-1000 oC). The high operating temperature in turn may lead to very complicated material degradation issues, significantly increasing the cost and reducing the durability of SOFC material systems. In order to widen material selections, reduce cost, and increase durability of SOFCs, there is a growing interest to develop intermediate temperature SOFCs (500-750 oC). However, lowering operating temperature will cause substantial increases of ohmic resistance of electrolyte and polarization resistance of electrodes. This dissertation aimed at developing high-performance intermediate-temperature SOFCs through the employment of a series of layered perovskite oxides …

Utilization Of Carbon Nanofibers Grown On Glass Microballoons (Nmbs) In Point-Of-Care Diagnostic Devices, Emmanuel Gikunoo

LSU Doctoral Dissertations

The use of point-of-care (POC) diagnostic systems holds great promise for the early detection of various diseases. However, detection limits for commercially available POC systems have not been able to meet the lower cutoffs offered by the specialized laboratory testing methods. Research into the use of carbon nanofibers (CNFs) grown on glass microballoons in POC devices was studied. The growth of several millions of the CNFs on each microballoon (NMBs) presented a large surface area with high probability of capturing minute concentrations of biospecies. Functionalization of the NMBs with the carboxyl group needed for biospecies conjugation was achieved by air …

Applications Of The Variational Approach To Fracture Mechanics, Ataollah Mesgarnejad

LSU Doctoral Dissertations

In this study we present the variational approach to fracture mechanics as a versatile tool for the modeling of the fracture phenomenon in solids. Variational fracture mechanics restates the problem of initiation and propagation of cracks in solids as an energy minimization problem. The edifice of this energy minimization problem is such that unlike other methods (e.g. extended finite element method XFEM, cohesive-zone methods) the variational approach to fracture mechanics, diminishes the need for an a priori knowledge of the crack path or ad hoc assumptions in the form of path selection laws. We will show applications of the variational …

Hot Corrosion Behaviour Of New Candidates For Thermal Barrier Coatings Application In Turbine Simulated Environments, Mohammad Hamed Habibi

LSU Doctoral Dissertations

Thermal barrier coatings (TBCs) are used gas turbine engines. The current material of choice (YSZ) degrades when it contacts with impurities arise from low quality fuels such vanadium and sulfur. YSZ cannot be used in temperature higher than 900˚C. Higher efficiency and performance of gas turbine engines will require a new generation of thermal barrier coatings (TBCs). In current work, hot corrosion behavior of new candidates including Gd2Zr2O7, ZrO2 stabilized with Ta2O5, zirconia stabilized with both Ta2O5 and Y2O3 and zirconia stabilized with CeO2 and TiO2 is investigated. For YSZ case, the reaction between NaVO3 and Y2O3 produces YVO4 and …

Static, Vibration Analysis And Sensitivity Analysis Of Stepped Beams Using Singularity Functions, Peng Cheng, Carla Davila, Gene Hou

Mechanical & Aerospace Engineering Faculty Publications

A systematic approach is presented in this paper to derive the analytical deflection function of a stepped beam using singularity functions. The discontinuities considered in this development are associated with the jumps in the flexural rigidity and the applied loads. This approach is applied to static and vibration analyses of stepped beams. The same approach is later extended to perform sensitivity analysis of stepped beams. This is done by directly differentiating the analytical deflection function with respect to any beam-related design variable. The particular design variable considered here is the location of discontinuity in flexural rigidity. Example problems are presented …

Novel Syntheses And Surface Modifications Of Electrode Materials For Superior Lithium-Ion Batteries, Jianqing Zhao

LSU Doctoral Dissertations

Rechargeable lithium-ion battery is one of the most promising energy conversion and storage systems that offers high energy and powder densities, long service life and assuring safety. Performance of lithium-ion batteries crucially relies on electrochemical characteristics of electrode materials, i.e., anode and cathode materials. This dissertation work aims at developing novel electrode materials with high capacity, excellent cycling stability and remarkable rate capability for next-generation lithium-ion batteries. The effects of surface modifications for LiMn2O4 cathode materials are studied by depositing ultrathin conformal amphoteric oxides via atomic layer deposition (ALD). In the case of ZnO coating, the thickness of ZnO ALD …

Energy Dissipation And Entropy Generation During The Fatigue Degradation: Application To Health Monitoring Of Composites, Ali Kahirdeh

LSU Doctoral Dissertations

In this dissertation, an experimental approach for characterizing energy dissipation and degradation evolution in a woven Epoxy/Glass (G10/FR4) laminate subjected to fully reversed bending fatigue test is presented. Infrared thermography and acoustic emission are utilized to characterize the degradation progression. The results show similar evolutionary response indicating the presence of three degradation stages. The effect of the surface cooling on the fatigue life of the laminates is investigated both experimentally and analytically. The results show that the life of the laminate is highly dependent on the temperature and that surface cooling can significantly increase the fatigue life of the laminate. …

Tomographic Imaging Of Combustion Zones Using Tunable Diode Laser Absorption Spectroscopy (Tdlas), Avishek Guha

LSU Doctoral Dissertations

This work concentrates on enabling the usage of a specific variant of tunable diode laser absorption spectroscopy (abbr. TDLAS) for tomogaphically reconstructing spatially varying temperature and concentrations of gases with as few reconstruction artifacts as possible. The specific variant of TDLAS used here is known as wavelength modulation with second harmonic detection (abbr. WMS-2f) which uses the wavelength dependent absorbance information of two different spectroscopic transitions to determine temperature and concentration values. Traditionally, WMS-2f has generally been applied to domains where temperature although unknown, was spatially largely invariant while concentration was constant and known to a reasonable approximation (_x0006_+/- 10% …