Mechanical Engineering Commons^™

Test 2156: New Holland Ts6.110, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2155: Kubota M6-141, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2153: Kubota M6-111, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2149a: Case Ih Magnum 340 Rowtrac, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2150: Case Ih Magnum 380 Rowtrac, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2164a: New Holland T9.700, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2159a: Case Ih Farmall 140a, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Rotary Vegetation System: Can It Speed Up The Absorption Of Indoor Air Pollutants?, Yusuke Nakamura

Summer Community of Scholars Posters (RCEU and HCR Combined Programs)

No abstract provided.

Corrosion Protection Systems In Offshore Structures, Hristo Ivanov

Williams Honors College, Honors Research Projects

Corrosion plays a pivotal role in the engineering world. Engineers of all disciplines must consider the dangers that this phenomenon can incur. Interestingly, corrosion mitigation is not a topic that is addressed in most academic curricula. The goal of this paper is to give engineering students a brief introduction into corrosion and some of the prevention techniques commonly used today.

The design of a corrosion protection system for offshore structures is discussed in order to illustrate how these techniques can be utilized even in the most extreme environments. First, the driving force behind corrosion is examined, introducing the basic mechanics …

Inlet Distortion Effects On The Unsteady Aerodynamics Of A Transonic Fan Stage, Daniel Oliver Reilly

Browse all Theses and Dissertations

A computational study was conducted to understand the influence of aircraft inlet distortion flow on the unsteady aerodynamic loading of a gas turbine fan stage. A single stage, transonic fan design with no inlet guide vanes was modeled with a commercial, computational fluid dynamics solver, STAR-CCM+, using the harmonic balance technique. The baseline inlet boundary condition applied to the model is consistent with that of a homeomorphic variant of the M2129 S-duct, and exhibited stagnation pressure distortion and a swirl pattern. The baseline inlet flow was decomposed and parameterized into a set of inlet boundary conditions which were individually applied …

The Effect Of Laser Power And Scan Speed On Melt Pool Characteristics Of Pure Titanium And Ti-6al-4v Alloy For Selective Laser Melting, Chandrakanth Kusuma

Browse all Theses and Dissertations

Selective Laser Melting (SLM) is an additive manufacturing (AM) technique that creates complex parts by selectively melting metal powder layer-by-layer. In SLM, the process parameters decide the quality of the fabricated component. In this study, single beads of commercially pure titanium (CP-Ti) and Ti-6Al-4V alloy are melted on a substrate of the same material as powder using an in-house built SLM machine. Multiple combinations of laser power and scan speed are used for single bead fabrication while the laser beam diameter and powder layer thickness are kept constant. This experimental study investigates the influence of laser power, scan speed and …

A Statistical Approach To Broadband Noise Suppression, Walter Eversman

Mechanical and Aerospace Engineering Faculty Research & Creative Works

A method for estimating achievable attenuation for broadband noise in an inlet duct, consistent with Dyer's suggestion that an appropriate model includes all propagating acoustic modes at equal power and random phase, is proposed. Broadband noise is represented in a frequency domain analysis by a statistical distribution of propagating duct modes. The required number of modes is estimated by Rice's approximation method and verified in FEM modeling. For each propagating circumferential mode propagating radial modes have equal acoustic power and random phase. Source acoustic power is distributed among circumferential modes according to the number of propagating radial modes in the …

Decomposition Of A Double Salt Ionic Liquid Monopropellant On Heated Metallic Surfaces, Steven P. Berg, Joshua L. Rovey

Mechanical and Aerospace Engineering Faculty Research & Creative Works

A monopropellant consisting of 59% hydroxylammonium nitrate and 41% 1-ethyl-3-methylimidazolium ethyl sulfate by mass is tested for decomposition on heated platinum, rhenium, and titanium surfaces. It was found that the propellant decomposes at 165 °C on titanium, which is the decomposition temperature of HAN. The onset temperature for decomposition on platinum was 85 °C and on rhenium it was 125 °C. This suggests that platinum and rhenium act as catalysts for the decomposition of the monopropellant. From the experimental data, Arrhenius-type reaction rate parameters were calculated. The activation energy for platinum was 3 times less than that of titanium suggesting …

Nx 10 For Engineering Design -- Learning Edition, Ming-Chuan Leu, Amir Ghazanfari, Krishna C. R. Kolan

Mechanical and Aerospace Engineering Faculty Research & Creative Works

NX is one of the world’s most advanced and tightly integrated CAD/CAM/CAE product development solution. Spanning the entire range of product development, NX delivers immense value to enterprises of all sizes. It simplifies complex product designs, thus speeding up the process of introducing products to the market.

The NX software integrates knowledge-based principles, industrial design, geometric modeling, advanced analysis, graphic simulation, and concurrent engineering. The software has powerful hybrid modeling capabilities by integrating constraint-based feature modeling and explicit geometric modeling. In addition to modeling standard geometry parts, it allows the user to design complex free-form shapes such as airfoils and …

Review Of Sensing Methodologies For Estimation Of Combustion Metrics, Libin Jia, Jeffrey D. Naber, Jason R. Blough

Michigan Tech Publications, Part 1

For reduction of engine-out emissions and improvement of fuel economy, closed-loop control of the combustion process has been explored and documented by many researchers. In the closed-loop control, the engine control parameters are optimized according to the estimated instantaneous combustion metrics provided by the combustion sensing process. Combustion sensing process is primarily composed of two aspects: combustion response signal acquisition and response signal processing. As a number of different signals have been employed as the response signal and the signal processing techniques can be different, this paper did a review work concerning the two aspects: combustion response signals and signal …

Direct Position Control Of Dielectric Barrier Discharge Filaments, Matthew C. Paliwoda, Joshua L. Rovey, Mitchell Wainwright

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Controllable patterns of plasma filaments are being explored for reconfigurable metamaterial applications. When operated in a filamentary mode, volume dielectric barrier discharges are known to produce patterns of self-organizing plasma filaments. In this work the presence and intensity of a single filament at a fixed location is controlled by an isolated and independently electrically adjusted needle electrode. Time-averaged normalized light intensity, current, and voltage are measured while varying the voltage of the needle through a self-biasing resistance. For a 7.5 kV, 3.2 kHz DBD, the needle-controlled filament discharges similar to adjacent filaments at low potentials but stops discharging at a …

The Effects Of Micro-Dimple Texture On The Friction And Thermal Behavior Of A Point Contact, Utsav Kamleshbhai Parmar

Browse all Theses and Dissertations

This study investigates the effects of the micro-dimple texture on the friction and surface temperature performances of a ball-on-disk contact, operating under the speed and load ranges that cover typical gearing applications. Circular shaped micro-dimple arrays with different dimple center distances and dimple depths are implemented on the ball surface to quantify the impacts of these two parameters on the friction coefficient and the maximum ball surface temperature. In addition, the contacts of three surface texture combinations, namely micro-dimpled and polished ball surface versus polished disk surface, polished ball surface versus polished disk surface and ground ball surface versus ground …

Elucidating The Role Of Microstructure, Texture, And Microtexture On The Dwell Fatigue Response Of Ti-6al-4v, Alec Mitchell Blankenship

Browse all Theses and Dissertations

Ambient temperature dwell sensitivity is known to be deleterious to the fatigue response of near-alpha titanium alloys. Dwell fatigue refers to the presence of a sustained hold at peak stress as opposed to the continuous variation of normal cyclic fatigue loading. This reduction in failure life-times from dwell loading is attributed to early crack nucleation and faster crack propagation. The degradation is the result of plastic anisotropy on the microstructural scale along with tendency of titanium alloys to creep at low temperatures at stresses well below the 0.2% offset yield strength. Despite being the most widely used titanium alloy, Ti-6Al-4V …

On The Experimental Evaluation Of Loss Production And Reduction In A Highly Loaded Low Pressure Turbine Cascade, Philip Steven Bear

Browse all Theses and Dissertations

Improvements in turbine design methods have resulted in the development of blade profiles with both high lift and good Reynolds lapse characteristics. An increase in aerodynamic loading of blades in the low pressure turbine section of aircraft gas turbine engines has the potential to reduce engine weight or increase power extraction. Increased blade loading means larger pressure gradients and increased secondary losses near the endwall. Prior work has emphasized the importance of reducing these losses if highly loaded blades are to be utilized. The present study analyzes the secondary flow field of the front-loaded low-pressure turbine blade designated L2F with …

Stress-Dependent Ultrasonic Scattering In Polycrystalline Materials, Christopher M. Kube, Christopher A Turner

Department of Mechanical and Materials Engineering: Faculty Publications

Stress-dependent elastic moduli of polycrystalline materials are used in a statistically based model for the scattering of ultrasonic waves from randomly oriented grains that are members of a stressed polycrystal. The stress is assumed to be homogeneous and can be either residual or generated from external loads. The stress-dependent elastic properties are incorporated into the definition of the differential scattering cross-section, which defines how strongly an incident wave is scattered into various directions. Nine stress-dependent differential scattering cross-sections or scattering coefficients are defined to include all possibilities of incident and scattered waves, which can be either longitudinal or (two) transverse …

Portable Camera Aided Simulator (Portcas) For Minimally Invasive Surgical Training, Ka-Chun Sui, Carl Nelson, Mohsen Zahiri, Dmitry Oleynikov

Department of Mechanical and Materials Engineering: Faculty Publications

The present disclosure is directed to a system and method for surgical training with low cost, reusable materials and a highly customizable virtual environment for skill-building. According to various embodiments, a surgical training tool is usable in conjunction with a support structure configured to at least partially constrain the tool movement. Meanwhile, the tool is tracked in real-time with off-tool detectors to generate a tool path driving a virtual rendering of the surgical training tool in an operative environment. The virtual rendering may be visually observable via a display device and may include a customizable and/or selectable operative environment with …

In-Field Fuel Use And Load States Of Agricultural Field Machinery, Santosh Pitla, Joe D. Luck, Jared Werner, Nannan Lin, Scott A. Shearer

Department of Agricultural and Biological Systems Engineering: Faculty Publications

The ability to define in-field tractor load states offers the potential to better specify and characterize fuel consumption rate for various field operations. For the same field operation, the tractor experiences diverse load demands and corresponding fuel use rates as it maneuvers through straight passes, turns, suspended operation for adjustments, repair and maintenance, and biomass or other material transfer operations. It is challenging to determine the actual fuel rate and load states of agricultural machinery using force prediction models, and hence, some form of in-field data acquisition capability is required. Controller Area Networks (CAN) available on the current model tractors …

Inter-Row Robot Navigation Using 1d Ranging Sensors, Tyler A. Troyer, Santosh Pitla, Ethan Nutter

Department of Agricultural and Biological Systems Engineering: Faculty Publications

In this paper a fuzzy logic navigation controller for an inter-row agricultural robot is developed and evaluated in laboratory settings. The controller receives input from one-dimensional (1D) ranging sensors on the robotic platform, and operated on ten fuzzy rules for basic row-following behavior. The control system was implemented on basic hardware for proof of concept and operated on a commonly available microcontroller development platform and open source software libraries. The robot platform used for experimentation was a small tracked vehicle with differential steering control. Fuzzy inferencing and defuzzification, step response and cross track error were obtained from the test conducted …

Characterization Of Piezoelectric Device For Implanted Pacemaker Energy Harvesting, Sunny Jay, Manuel Caballero, William Quinn, John Barrett, Martin Hill

Conference Papers

Novel implanted cardiac pacemakers that are powered by energy harvesters driven by the cardiac motion and have a 40 year lifetime are currently under development. To satisfy space constraints and energy requirements of the device, silicon-based MEMS energy harvesters are being developed in the EU project (MANpower). Such MEMS harvesters for vibration frequencies below 50 Hz have not been widely reported. In this paper, an analytical model and a 3D finite element model (FEM) to predict displacement and open circuit voltage, validated through experimental analysis using an off-the-shelf low frequency energy harvester, are presented. The harvester was excited through constant …

Magnetic Materials Characterization And Modeling For The Enhanced Design Of Magnetic Shielding Of Cryomodules In Particle Accelerators., Sanjay K. Sah

Theses and Dissertations

Particle accelerators produce beams of high-energy particles, which are used for both fundamental and applied scientific research and are critical to the development of accelerator driven sub-critical reactor systems. An effective magnetic shield is very important to achieve higher quality factor (Qo) of the cryomodule of a particle accelerator. The allowed value of field inside the cavity due to all external fields (particularly the Earth’s magnetic field) is ~15 mG or less. The goal of this PhD dissertation is to comprehensively study the magnetic properties of commonly used magnetic shielding materials at both cryogenic and room temperatures. This knowledge can …

Efficiency Evaluation Of A Magnetically Driven Multiple Disk Centrifugal Blood Pump, Kayla H. Moody

Theses and Dissertations

Heart failure is expected to ail over 8 million people in America by 2030 leaving many in need of cardiac replacement. To accommodate this large volume of people, ventricular assist devices (VADs) are necessary to provide mechanical circulatory support. Current VADs exhibit issues such as thrombosis and hemolysis caused by large local pressure drops and turbulent flow within the pump. Multiple disk centrifugal pumps (MDCPs) use shearing and centrifugal forces to produce laminar flow patterns and eliminate large pressure drops within the pump which greatly reduce risks that are in current VADs. The MDCP has a shaft drive system (SDS) …

Fabricating Superhydrophobic And Superoleophobic Surfaces With Multiscale Roughness Using Airbrush And Electrospray, Karam N. Almilaji

Theses and Dissertations

Examples of superhydrophobic surfaces found in nature such as self-cleaning property of lotus leaf and walking on water ability of water strider have led to an extensive investigation in this area over the past few decades. When a water droplet rests on a textured surface, it may either form a liquid-solid-vapor composite interface by which the liquid droplet partially sits on air pockets or it may wet the surface in which the water replaces the trapped air depending on the surface roughness and the surface chemistry. Super water repellent surfaces have numerous applications in our daily life such as drag …

Deformation Of Multifunctional Materials At Various Time And Length Scales: A Dic-Based Study, Behrad Koohbor

Theses and Dissertations

The focus in the present work is to explore and characterize the underlying deformation and failure mechanisms in multifunctional materials including woven composites and polymeric foams, using full-field measurements. Attention has been especially drawn towards the challenges associated with characterizing these materials at extreme length and time scales, and investigating the advantages of full-field measurements to resolve the existing limitations. Accordingly, the current limitations in the study of dynamic deformation response of low-impedance materials are identified. An approach based on the general stress equilibrium is presented and successfully implemented to include the concurrent effects of inertia and material compressibility into …

Effects Of Process Variants On Metallurgical And Mechanical Properties In Friction Stir Welding Of Aluminum Alloys, Xiaomin Huang

Theses and Dissertations

Conventional shoulder friction stir welding (CSFSW) produces uneven heat input through welded material thickness: higher close to the top and lower close to the bottom. When CSFSW is applied on certain aluminum alloys, such as 7xxx and 2xxx series high strength aluminum alloys which contain low melting point intermetallic, overheating and local melting may happen close to weld crown. Stationary shoulder friction stir welding (SSFSW) may generate much more uniform heat input through plate thickness than CSFSW due to the non-rotating shoulder and rotating pin. Therefore, overheating and local melting are expected to be avoided in SSFSW. Furthermore, local properties …

Numerical Analysis Of Flexural Slip During Viscoelastic Buckle Folding, Davi Rodrigues Damasceno

Masters Theses

"Flexural slip is considered to be an important folding mechanism contributing in the development of different folds such as chevron, and kink-band buckle folds. Various filed studies have provided a general conceptual and qualitative understanding of flexural slip. However, quantitative evidence of the importance of the flexural slip mechanism during fold evolution is sparse, as the actual amount of surface parallel displacement, and timing, is difficult to measure accurately, due to the lack of suitable strain markers.

In this study 2D finite element analysis is used to overcome these disadvantages and to simulate flexural slip during viscoelastic buckle folding. Variations …