Mechanical Engineering Commons^™

Low-Temperature Aqueous Corrosion Behavior Of Uranium Molybdenum Alloys, Levi D. Gardner

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Nuclear fuel characterization requires understanding of the various conditions to which materials are exposed in-reactor. One of these important conditions is corrosion, particularly that of fuel constituents. Therefore, corrosion behavior is of special interest and an essential part of nuclear materials characterization efforts. In support of the Office of Material Management and Minimization’s Reactor Conversion Program, monolithic uranium-10 wt% molybdenum alloy (UMo) is being investigated as a low enriched uranium alternative to highly enriched uranium dispersion fuel currently used in domestic high performance research reactors. The aqueous corrosion behavior of U-Mo is being examined at Pacific Northwest National Laboratory (PNNL) …

Modified Trajectory Shaping Guidance For Autonomous Path Following Control Of Platooning Ground Vehicles, Ishmaal T. Erekson

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

This thesis proposes a modification of trajectory shaping guidance to provide more accurate path convergence in curved paths. The object of this thesis is to apply this simple guidance law to platooning control to ensure all vehicles in the platoon converge to a desired constant radius path at a desired vehicle separation distance. To show the viability of this new guidance law, it is shown mathematically to be exponentially stable. It is also confirmed through simulations and on ground robots.

Path Following By A Quadrotor Using Virtual Target Pursuit Guidance, Abhishek Manjunath

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Missile guidance laws have been solely developed to follow and intercept a target thereby destroying or damaging it. In this research, the primary objective is to modify and adopt a missile guidance law to be used on a quadrotor to follow a virtual target. The target is termed 'virtual' as it only exists mathematically in the form of equations. The goal is to have the quadrotor successfully following the predefined path (described by the target) while maintaining a fixed distance from the virtual target. To ensure viability and assess performance, a detailed comparison with another path following law is made.

Quadrotor Uav Path Following Using Trajectory Shaping, Parwinder Singh Mehrok

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

The propose of this research is to develop a path following control law known as Trajectory Shaping. The approach is to develop a three- dimensional (3D) version of it from an existing two-dimensional (2D) model. Apart from research on this 3D control law, a multirotor unmanned aerial vehicle (UAV) platform, having four rotors and known as quadrotor is designed from the ground up for validating the concept of path following. Several pre-defined paths like the circle and figure-eight trajectories are used to apply the newly developed version of this control law. The existing 2D concept of Trajectory Shaping guidance …

Throttleable Gox/Abs Launch Assist Hybrid Rocket Motor For Small Scale Air Launch Platform, Zachary S. Spurrier

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

The ability for an aircraft-based launch platform to place an orbital payload onto a nominal launch trajectory at a higher energy state -- altitude, velocity, flight path angle, and azimuth --using highly-efficient air breathing propulsion instead of a much lower-efficiency rocket system, offers the potential for a significantly smaller launch vehicle. An airborne platform also provides the ability to launch from multiple locations and allows for significantly increased "system responsiveness." The NASA Armstrong Flight Research Center’s Towed Glider Air-Launch System (TGALS) is a small-scale flight research project investigating the feasibility for a remotely-piloted, towed, glider system to act as a …

Computing Research In Academia: Classifications, Keywords, Perceptions, And Connections, Sung Han Kim

Theses and Dissertations

The Association for Computing Machinery (ACM) recognizes five computing disciplines: Computer Science (CS), Computer Engineering (CE), Information Technology (IT), Information Systems (IS), and Software Engineering (SE). Founded in 1947 the ACM is the world's largest society for computing educators, researchers, and professionals. While Computer Science has been a degree program since 1962, the other four are relatively new. This research focuses on understanding the graduate research in four of the five ACM disciplines (CS, CE, IT, and IS) using a large body of thesis and dissertation metadata. SE is not found in the metadata and graduate work in SE is …

On The Scattering Of An Acoustic Plane Wave By A Soft Prolate Spheroid, Joseph Michael Borromeo

UNLV Theses, Dissertations, Professional Papers, and Capstones

This thesis solves the scattering problem in which an acoustic plane wave of propagation number K1 is scattered by a soft prolate spheroid. The interior field of the scatterer is characterized by a propagation number K2, while the field radiated by the scatterer is characterized by the propagation number K3. The three fields and their normal derivatives satisfy boundary conditions at the surface of the scatterer. These boundary conditions involve six complex parameters depending on the propagation numbers. The scattered wave also satisfies the Sommerfeld radiation condition at infinity. Through analytical methods, series representations are constructed for the interior field …

Portable High Throughput Digital Microfluidics And On-Chip Bacteria Cultures, Yiyan Li

UNLV Theses, Dissertations, Professional Papers, and Capstones

An intelligent, portable, and high throughput digital microfluidic (DMF) system is developed. Chapter 1 introduces microfluidics and DMF systems. In Chapter 2, a low-cost and high resolution capacitive-to-digital converter integrated circuit is used for droplet position detection. A field-programmable gate array FPGA is used as the integrated logic hub of the system for highly reliable and efficient control of the circuit. In this chapter a fast-fabricating PCB (printed circuit board) substrate microfluidic system is proposed. Smaller actuation threshold voltages than those previously reported are obtained. Droplets (3 µL) are actuated using 200 V, 500 Hz DC pulses. Droplet positions can …

Effect Of Thermal Treatment On High Temperature Deformation Of Alloy Ep-~823, Martin Milburn Lewis

UNLV Theses, Dissertations, Professional Papers, and Capstones

The objective of this research topic is to determine mechanical properties of Alloy EP-823 and to provide a mechanistic understanding of its sensitivity to both thermal treatment and performance temperature. EP-823 is a leading target material for accelerator-driven waste transmutation applications. Overall, the tensile test results of Alloy EP-823 indicated a general trend of decreasing mechanical performance with an increase in tempering time. An increase in tempering time had a statistically significant inverse relationship with ultimate tensile strength (UTS) and yield strength (YS). An increase in tempering time did not have a significant effect on elongation and reduction in area. …

Strong Coupling Between Mid-Infrared Localized Plasmons And Phonons, W. Wan, Xiaodong Yang, Jie Gao

Mechanical and Aerospace Engineering Faculty Research & Creative Works

No abstract provided.

Neutron-Gamma Discrimination In Elpasolite Scintillator Detector, Brittany Morgan

UNLV Theses, Dissertations, Professional Papers, and Capstones

Existing nuclear stockpiles and weapons-making capabilities imperil the global community. Current nonproliferation efforts involve the research and development of newer, more efficient detection systems that can be deployed for the interdiction and monitoring of special nuclear materials (SNM). Spontaneous and induced fission events in SNM produce neutrons and gamma rays, which can be detected and analyzed, in particular, using scintillator detectors. Various electronic data acquisition systems and data analysis methods have been employed to record and characterize neutron and photon signatures. The goal of this thesis is to develop a new method of discrimination between neutrons and photons in the …

Advances In Repurposing And Recycling Of Post-Vehicle-Application Lithium-Ion Batteries, Charles R. Standridge, Lindsay Corneal, Nicholas Baine

Mineta Transportation Institute

Increased electrification of vehicles has increased the use of lithium-ion batteries for energy storage, and raised the issue of what to do with post-vehicle-application batteries. Three possibilities have been identified: 1) remanufacturing for intended reuse in vehicles; 2) repurposing for non-vehicle, stationary storage applications; and 3) recycling, extracting the precious metals, chemicals and other byproducts. Advances in repurposing and recycling are presented, along with a mathematical model that forecasts the manufacturing capacity needed for remanufacturing, repurposing, and recycling. Results obtained by simulating the model show that up to a 25% reduction in the need for new batteries can be achieved …

Temporally And Spatially Resolved Quantification Of Hemodynamic Forces And Endothelial Mechanics, Lori M. Lambert

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

The endothelium is a thin layer of endothelial cells that line the interior surface of an artery. Due to their direct contact with blood flow, endothelial cells experience varying hemodynamic forces and respond to these forces by altering their morphology. When plaque and other substances accumulate in the walls of arteries, i.e., atherosclerosis, endothelial cells have abnormal responses to blood flow. Studying atherosclerosis progression is, therefore, a two-fold investigation into 1) the hemodynamic forces that cause endothelial responses, and 2) the biological and mechanical responses of endothelial cells. The ultimate goal of this study was to develop an experimental …

Numerical Simulation Of Tip Clearance Impact On A Pumpjet Propulsor, Lin Lu, Guang Pan, Jing Wei, Yipeng Pan

Ocean Engineering and Marine Sciences Faculty Publications

Numerical simulation based on the Reynolds Averaged NaviereStokes (RANS) Computational Fluid Dynamics (CFD) method had been carried out with the commercial code ANSYS CFX. The structured grid and SST keu turbulence model had been adopted. The impact of noncondensable gas (NCG) on cavitation performance had been introduced into the Schnerr and Sauer cavitation model. The numerical investigation of cavitating flow of marine propeller E779A was carried out with different advance ratios and cavitation numbers to verify the numerical simulation method. Tip clearance effects on the performance of pumpjet propulsor had been investigated. Results showed that the structure and characteristics of …

Direct Printing Of Microstructures By Femtosecond Laser Excitation Of Nanocrystals In Solution, W. Shou, Heng Pan

Mechanical and Aerospace Engineering Faculty Research & Creative Works

No abstract provided.

Multiphase Ferrofluid Flows For Micro-Particle Focusing And Separation, R. Zhou, Cheng Wang

Mechanical and Aerospace Engineering Faculty Research & Creative Works

No abstract provided.

Effect Of Non-Uniform Air-Side Velocity Distribution On Heat Transfer Model Predictions For Microchannel Condenser., Zachary Chapin

Electronic Theses and Dissertations

This is a study of the effects on heat transfer capacity predictions of microchannel condensers when airflow is maldistributed due to the shape of the condenser. The three shapes investigated in this study are flat, U-shape and roll. Each coil was tested in a water calorimeter and those results were compared to the model prediction. The model prediction was calculated using CoilDesigner™ modeling software with standard correlations. Using the uniform airflow assumption, the model over predicted the heat capacity measured in the calorimeter by 5-11% depending on the coil and inlet conditions. The local airflow velocity was measured using a …

Mechanical Properties And Microstructure Evolution Of 17-4 Ph Stainless Steel Processed By Laser-Powered Bed Fusion., Harish Irrinki

Electronic Theses and Dissertations

Laser powder bed fusion (L-PBF) is a potential manufacturing route for the production of tooling using different steel materials. However, there is a limited understanding of how the mechanical properties and microstructures of the L-PBF produced parts vary with change in powder type and process conditions. The current research studied the influence of L-PBF process parameters on mechanical properties and microstructures of 17-4PH stainless steel using gas and water-atomized powders. The results demonstrate the feasibility of using water-atomized powders as starting raw materials instead of typically used gas-atomized powders to fabricate parts in the L-PBF process at high energy densities.

The Child Brain Computes And Utilizes Internalized Maternal Choices, S. Seung-Lark Lim, J. Cherry C. Bradley, A. Davis, S. N. Balakrishnan, O. Ha, J. Bruce, A. Bruce

Mechanical and Aerospace Engineering Faculty Research & Creative Works

No abstract provided.

Maximization Of The Annual Energy Production Of Wind Power Plants By Optimization Of Layout And Yaw-Based Wake Control, Pieter Gebraad, Jared Thomas, Andrew Ning, Paul Fleming, Katherine Dykes

Faculty Publications

This paper presents a wind plant modeling and optimization tool that enables the maximization of wind plant annual energy production (AEP) using yaw-based wake steering control and layout changes. In order to make predictions of wind plant AEP, necessary extensions of the original wind plant wake interaction model include the coupling with a detailed rotor model and a control policy for turbine blade pitch and rotor speed. This coupling allows the prediction of power production with wake effects throughout a range of wind speeds. Results of an optimization study on a wind plant based on the Princess Amalia Wind Park …

Mechanical Engineering News, Georgia Southern University

Mechanical Engineering: News & Publications (2013-2023)

• Dr. Mitra Honored by PLTW

Ubisol-Q10 Prevents Glutamate-Induced Cell Death By Blocking Mitochondrial Fragmentation And Permeability Transition Pore Opening, Santosh Kumari, Suresh L. Mehta, Gaolin Z. Milledge, Xinyu Huang, P Andy Li

Faculty Publications

Mitochondrial dysfunction and oxidative stress are the major events that lead to the formation of mitochondrial permeability transition pore (mPTP) during glutamate-induced cytotoxicity and cell death. Coenzyme Q10 (CoQ10) has widely been used for the treatment of mitochondrial disorders and neurodegenerative diseases. Comparing to traditional lipid-soluble CoQ10, water soluble CoQ10 (Ubisol-Q10) has high intracellular and intra-mitochondrial distribution. The aims of the present study are to determine the neuroprotective effects of Ubisol-Q10 on glutamate-induced cell death and to explore its functional mechanisms. HT22 neuronal cells were exposed to glutamate. Cell viability was measured and mitochondrial fragmentation was assessed by mitochondrial imaging. …

Evaluation Of Alternative Implementation Methods Of Failure Sampling Approach For Structural Reliability Analysis, Kapil Patki, Christopher D. Eamon

Civil and Environmental Engineering Faculty Research Publications

In this paper, several alternative approaches are used to implement the failure sampling method for structural reliability analysis and are evaluated for effectiveness. Although no theoretical limitation exists as to the types of problems that failure sampling can solve, the method is most competitive for problems that cannot be accurately solved with reliability index-based approaches and for which simulation is needed. These problems tend to have non-smooth limit state boundaries or are otherwise highly nonlinear. Results from numerical integration and three extrapolation approaches using the generalized lambda distribution, Johnson's distribution, and generalized extreme value distribution are compared. A variety of …

Automated Mini-Channel Platform For Studying Plant Root Environments, Kevin F. Kreis

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Plants are crucial to our lives; they provide us with building materials, oxygen, and food. A season’s crop yield can be significantly affected by local environmental factors. Farming practices currently focus on using fertilizer, pesticides, monitoring water availability, and genetic modification of the plant to increase crop yield. Improving fundamental understanding of plant root interactions with their local soil environment, or rhizosphere, will help improve crop yield. Studying such interactions is challenging because roots are underground, making it difficult to observe interactions and to manipulate the local soil environment.

The goal of this thesis is to develop an automated mini-channel …

Improving Radiation And Stress Corrosion Cracking Resistance Of Austenitic Stainless Steels By Laser Shock Peening, Qiaofeng Lu

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Structural alloys for Generation-IV nuclear reactors need to endure a high neutron dose, high temperature, and corrosive coolant. Austenitic stainless steels, particularly the oxide-dispersion-strengthened (ODS) austenitic steels, are promising candidate materials, but they suffer several limits such as irradiation damage and stress corrosion cracking (SCC). This research applies a laser shock peening (LSP) process to improve the radiation and SCC resistance of austenitic stainless steels in simulated nuclear reactor environments. A high density dislocation networks, stacking faults and twin boundaries were generated in the surface region of 304 steels by the shock wave-material interactions in the LSP process. In-situ TEM …

Ascanius Project: Mech 401/402 Senior Capstone Experience, Ray H. Colquhoun, Joshua Solberg, Martin Tangari, Emanuel Di Stasio

Honors Thesis

This report describes the analysis, design, and test, and launch of a high power reusable rocket. The design goals were to reach a target altitude of 3000’, deploy a payload module containing an egg that can be safely recovered, and record flight video. The rocket was 62.13 in long fully assembled, had a dry mass of 2.764 kg (3.077 kg wet), and was propelled using an I-class solid fuel rocket motor (Cesaroni I-216-CL). The nose cone and tail cone were fabricated by the team from carbon fiber reinforced polymer (CFRP) via wet layup and vacuum bagging. The fins were constructed …

Least Cost Analysis For Solar Photovoltaic Maintenance Of The Wmu Miller Auditorium Array, Kelsey Pitschel

Honors Theses

The solar photovoltaic array at Miller Auditorium is a 50 kW DC system that has relied on five seasonal angle adjustments and no cleaning measures to reach an average of 64.7 MWh annual energy generation since 2012 1 . This amount of energy generation yields $7,046 in annual energy savings based on current market pricing for end use electricity of $0.1089/kWh 2 . The current adjustment schedule based on seasonal tilts accounts for an annual costs between $760 and $848, but actual adjustments have historically not taken place according to the existing schedule. The analysis focuses on optimizing net energy …

Design Of Medical Devices For Diagnostics In The Gastrointestinal System, Charles R. Welch

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

This thesis presents the design, controls, and testing of two systems: a novel colonoscope locomotion design for diagnostics, and a biosensor capsule that implants a sensor in the small intestine. Each system requires special design considerations for use in the gastrointestinal system.

Colonoscopy procedures are recommended as a screening for colon cancer and related conditions after the age of 50. The need for an improved colonoscope that reduces the colonoscopy time and patient discomfort is apparent. The semi-autonomous device presented here could likely reduce the colonoscopy procedure time by allowing the physician to focus more on the diagnosis and less …

Leidenfrost Energy Barriers, James Peck, Anton Hassebrook, Craig Zuhlke, Troy P. Anderson, Dennis R. Alexander, George Gogos, Sidy Ndao

UCARE: Research Products

In this work, an “Energy Barrier” was created to control the motion of Leidenfrost droplets. This barrier was created by functionalizing a portion of a mirror-polished stainless steel 304 surface with Femtosecond Laser Surface Processing (FLSP). FLSP results in superhydrophilic, hierarchical, micro- and nanostructures which are highly wetting and thus have an increased Leidenfrost temperature. Water droplets in the film boiling state were deposited, and propelled by gravity towards the Energy Barrier interface. Room temperature droplets were deposited over a range of surface temperatures beginning with the Leidenfrost temperature of mirror-polished stainless steel 304 and culminating at the Leidenfrost temperature …

Method For Determining Time-Resolved Heat Transfer Coefficient And Adiabatic Effectiveness Waveforms With Unsteady Film Cooling, James L. Rutledge, Jonathan F. Mccall

AFIT Patents

A new method for determining heat transfer coefficient (h) and adiabatic effectiveness (η) waveforms h(t) and η(t) from a single test uses a novel inverse heat transfer methodology to use surface temperature histories obtained using prior art approaches to approximate the h(t) and η(t) waveforms. The method best curve fits the data to a pair of truncated Fourier series.