Power and Energy Commons^™

2024 Marine Energy Collegiate Competition, Nora Riedinger, Miles Mikkelsen, Brendan Stratford, Derek Tom, Zach Kwast, Harmon Yanikian-Sutton, Kennedy Urcelay, Tori Thomas, Brady Caron

Mechanical Engineering

PolyWave Energy is the second team from California Polytechnic University at San Luis Obispo to compete in the Marine Energy Collegiate Competition. PolyWave Energy consists of Mechanical Engineering, Electrical Engineering, and Business Administration students who have worked together from September 2023 to May 2024 on designing, building, and testing a marine power device to serve a selected market.

In response to the escalating concerns surrounding carbon emissions, climate change, and the depletion of fossil fuels, California Polytechnic State University’s Polywave Energy team has developed a sustainable and reliable energy source for Autonomous Underwater Vehicle (AUV) charging. Through extensive research of …

Electrical Design For Moringa Leaf Dryer, Jake Weiss

Construction Management

The objective of this project is to provide a methodology to the electrical scope of mechanical leaf dryers. This dryer was particularly designed for an off-grid farm in New Longoro, Ghana in which resources and materials are limited. The electrical system must be designed so that it works with motors, variable frequency drives, worm gears, and other materials that could be sourced in Ghana. The system should also draw minimal power so that remaining photovoltaic energy could be utilized on the farm. The system should be simplistic and repeatable for other farmers to utilize. By using both a numerical analysis …

Design And Analysis Of A New Buck-Boost Converter With A Low-Side Switch, Abdullah Awidah

Master's Theses

This work explores the design, simulation, construction, and analysis of a novel Non-isolated DC-DC Buck-Boost converter which has the advantage of incorporating a low-side switch compared to the traditional buck-boost which requires a high-side switch. This allows the use of a low-side driver which further simplifies the design and operation of the converter. The proposed Buck-Boost converter was constructed to provide -24 V output from an input range of 12V-18V with 15V nominal input at 10W maximum output power utilizing 500kHz switching frequency. Findings from simulations and hardware tests verify that the converter effectively provides the desired -24 V output …

A Hybrid Computer To Solve The Selective Harmonic Minimization Problem In Single-Phase Inverters, Dillon Nguyen

Master's Theses

Power electronics possess forms of non-ideality due to the nonlinearity present in physical switches. These switches are driven with pulse width modulation (PWM), which properly down-converts or up-converts based on converter topology. When these switches turn on or off, they introduce the main proponent of efficiency loss: harmonics. This becomes a nonlinear optimization problem with many converters. The solution proposed in this thesis is an analog/digital hybrid computer that utilizes the speed of analog computation and the accuracy of digital computing together. A Plexim RT Box provides the programmability needed for algorithms, while the analog circuit provides low-power, high-speed computation …

Design Of A Dynamic, Reconfigurable, Self-Balancing Battery Pack, Alexander Hallett Neiman

Master's Theses

This thesis details the design and testing of a reconfigurable battery array. Reconfigurable battery arrays, specifically for mobile applications, have the potential to reduce or eliminate use of auxiliary charging, balancing, and inverter systems. Design work included a bidirectional solid state switch and a cell-to-cell bidirectional current-limiting power converter. While the overall efficiency, size, and cost of the battery pack was not competitive with existing options, it demonstrated cell-to-cell balancing and native four-level square wave AC inverter output with an array of only two cells. This demonstrates viability of the concept as well as reveals important requirements and safety features …

Decentralized Control Of Renewable Generation Systems, Milad Shojaee

Dissertations

As the global community struggles with the escalating challenges of climate change and environmental degradation, the transition to renewable energy sources has emerged as a paramount solution. Harnessing energy from renewable sources such as solar, wind, and hydro power not only alleviates the adverse effects of conventional fossil fuel energy sources, but also establishes a foundation for a sustainable and resilient future. Microgrids have been utilized as a feasible platform to integrate renewable energy sources into the electrical power generation networks. They include one or more generation units connected to nearby users, and are able to operate in both grid-connected …

Graph-Based Modeling And Optimization Of Wpt Systems For Evs, Matthew J. Hansen, Greg Droge, Abhilash Kamineni

Electrical and Computer Engineering Student Research

A model of a system of wireless power transfer (WPT) pads is developed, where each WPT pad is modeled as a node and the coupling between pads is modeled as graph edges. This modeling approach is generalized to admit primary, secondary, and booster coils, where power can flow among the pads and a pad can fill multiple roles. An excitation in one pad induces voltage and current in all neighboring pads, causing each pad to act as both a booster coil and either a transmitter or a receiver. Power flow through the entire system can be modeled with the graph …

Estimation Of Useful-Stage Energy Returns On Investment For Fossil Fuels And Implications For Renewable Energy Systems, Emmanuel Aramendia, Paul E. Brockway, Peter G. Taylor, Jonathan B. Norman, Matthew K. Heun, Zeke Marshal;

University Faculty Publications and Creative Works

The net energy implications of the energy transition have so far been analysed at best at the final energy stage. Here we argue that expanding the analysis to the useful stage is crucial. We estimate fossil fuelsʼ useful-stage energy returns on investment (EROIs) over the period 1971–2020, globally and nationally, and disaggregate EROIs by end use. We find that fossil fuelsʼ useful-stage EROIs (~3.5:1) are considerably lower than at the final stage (~8.5:1), due to low final-to-useful efficiencies. Further, we estimate the final-stage EROI for which electricity-yielding renewable energy would deliver the same net useful energy as fossil fuels (EROI …

An Integrated Resource Planning Proposal For Tucson Electric Power, Valeria Bernal

Master's Projects and Capstones

An integrated resource plan (IRP) is crucial for utilities to determine the most cost-efficient energy resources while considering system reliability, environmental impact, and regulatory requirements. VitalsparK developed an IRP for Tucson Electric Power (TEP) to transition its current 70% thermal and 30% renewable energy portfolio, emitting 740 grams of CO2 per kWh, toward carbon neutrality by 2050. The proposed plan involves retiring existing infrastructure, adding 8 GW of renewable and storage capacity, and incorporating 2.5 GW of net-zero natural gas power plants. VitalsparK presented two scenarios: the Reference (REF) Case, which focuses on the least-cost portfolio to meet demand through …

Residential Ders In Service-Oriented Load Participation: Enhancing Grid Flexibility, Zhongkai Zeng

Dissertations and Theses

Amidst concerns about power consumption during peak periods and potential grid instability, the role of Distributed Energy Resource (DER) aggregation comes into consideration. Smart electric water heaters with remote capabilities and energy storage offer load reduction capabilities that can help maintain grid stability and manage residential energy consumption. DERs address challenges posed by stochastic renewable energy generation and fossil fuel power plant emissions, playing a contributing role in load shifting and enhancing grid flexibility by participating in energy management programs.

However, high unenrollment rates in demand response programs, notably programs that use direct load control, persist due to customer dissatisfaction. …

Engineering Composite Gridlines For Improved Solar Module Reliability, Andre Chavez

Electrical and Computer Engineering ETDs

Renewable energy sources, such as solar power, are rapidly expanding worldwide to meet increased energy demands. However, these sources are exposed to challenging environmental stressors, such as extreme wind, heavy snow loads, and hailstorms that can cause irreversible damage to the crystalline semiconductor solar cells. Today, single crystalline silicon solar cells dominate the market, and our work is focused on improving their reliability against environmental stressors. One of the main degradation mechanisms caused by environmental stressors is cell cracks. These microcracks can go virtually undetected and lead to reduced power output from solar modules over time. To solve this engineering …

Ultra‐Fast Finite Element Analysis Of Coreless Axial Flux Permanent Magnet Synchronous Machines, Yaser Chulaee, Dan Ionel

Power and Energy Institute of Kentucky Faculty Publications

Large‐scale design optimisation techniques enable the design of high‐performance electric machines. Electromagnetic 3D finite element analysis (FEA) is typically employed in optimisation studies for accurate analysis of axial flux permanent magnet(AFPM) machines, which require extensive computational resources. To reduce the computational burden, a FEA‐based mathematical method relying on the geometric and magnetic symmetry of coreless AFPM machines is proposed to estimate the machine performance indicators using the least number of FEA solutions, thereby significantly lowering the running time. This method is generally applicable to AFPM machines with low saturation effects and cogging torque as exemplified for a printed circuit board …

Ionic Conductivity, Li+ Transference Number, And Diffusion Coefficient Of A Solid-State Electrolyte Composite, Lizbeth Zurita

Reviews, Analyses, and Instructional Studies in Electrochemistry (RAISE)

The design of solid-state electrolyte (SSE) composites involves the fundamental study of transport properties, such as ionic conductivity. This transport property is influenced by the transport mechanisms of the charge species inside the composite, such as diffusion and migration. In this work, we perform the measurement of these three parameters through defined techniques. The resulting parameters were: ionic conductivity, the diffusion coefficient, and the Li+ transference number.

Design Optimization Of A Direct-Drive Wind Generator With A Reluctance Rotor And A Flux Intensifying Stator Using Different Pm Types, Ali Mohammadi, Oluwaseun A. Badewa, Yaser Chulaee, Donovin D. Lewis, Somasundaram Essakiappan, Madhav Manjrekar, Dan M. Ionel

Power and Energy Institute of Kentucky Faculty Publications

This paper presents a large-scale multi-objective design optimization for a direct-drive wind turbine generator concept that is based upon an experimentally validated computational model for a small-scale prototype motor of the same type. By integrating an outer reluctance-type rotor and a segmented stator with toroidally wound single-coil modules containing spoke-type PMs, the design optimization aims to minimize losses, active mass, and torque ripple while adhering to a power factor constraint. The AC windings and PMs are positioned in the stator and this concept enhances flux concentration, enabling the use of more affordable high energy non-rare-earth (special type) magnets. The exterior …

Improving The Power Efficiency Of Woodward’S High-Power Inverter (Hpi) Using Algorithmic Part Selection., Jaron Holder, Ali Al Gazwi, John Childers, Jose Soublett

Honors Capstones

Woodward Inc. is a secondary aerospace manufacturer based in the USA that specializes in aircraft power and control systems. This senior design project was concerned with a power systems platform currently in development by Woodward, the High-Power Inverter (HPI) system. In this report, the senior design group from Northern Illinois University (NIU) demonstrated the creation of an algorithmic part selection process to choose more power-efficient electrical components, the prototyping using MATLAB Simulink, and the practical testing that showed an increase of 7% in the power efficiency of the HPI system.

A 10 Kv Sic Mosfet Power Module With Optimized System Interface And Electric Field Distribution, Xiaoling Li

Graduate Theses and Dissertations

This dissertation introduces a holistic and systematic design methodology tailored to the 10 kV silicon carbide (SiC) MOSFET power modules to achieve multi-objective optimization with enhanced electric-field (E-field) distribution, minimized common-mode (CM) parasitic capacitance, and reduced system-level parasitic inductances. The proposed approach encompasses two innovative techniques: 1) an electric-potential-oriented module-system interface to reduce system-level parasitic inductance while maximizing insulation capability; 2) stacked substrates with patterned middle layer copper to alleviate the E-field concentration at the triple-point and reduce the maximum E-field without compromising on thermal resistance. The effectiveness of these innovative approaches is substantiated through the development of a 10 …

High Bandwidth Hybrid Current Sensor Readout Interface For Power Applications, Asma Mahar

Graduate Theses and Dissertations

High-density and power-efficient circuits have become realizable with the advent of wide bandgap semiconductor devices due to their high switching speed and lower conduction/switching losses. The operation of these circuits requires current information for protection, monitoring, and control. For the realization and a further boost in the efficiency of such power circuits, small size, non-invasive, high bandwidth current sensors with noise immunity, accuracy, and linearity are required. Various hybrid sensors have been reported to meet the requirements of emerging power circuits. A combination of a magneto resistor or Hall sensor and a coil is used to cover a wide frequency …

High Performance Silicon Carbide Based Converters For Powertrain Electrification, Nan Lin

Graduate Theses and Dissertations

With the increasing concern towards environment protection, electric vehicles (EVs) and hybrid electric vehicles (HEVs) have become popular in recent years. They not only help reduce carbon emissions, but also come with other benefits such higher efficiency and better user experience. Many countries and vehicle manufactures have made their plans to keep up with this trend in vehicle electrification. Powertrain is an assembly of components in a vehicle that pushes it forward. As for EVs and HEVs, their powertrains are composed of one or more power electronics converters, which are significant to the system. Silicon carbide MOSFETs have shown superior …

Design And Implementation Of High-Frequency Dc-Dc Converters For Ev Applications, Rahul Biswash

Graduate Theses and Dissertations

The power electronics industry has been revolutionized by introducing wide bandgap semiconductor devices, such as Silicon Carbide (SiC) and Gallium Nitride (GaN). Due to their high frequency, high temperature, and high voltage operating capabilities, wide bandgap devices boast significant improvements in power density, efficiency, and reliability, as evidenced by their ability to decrease the size of power converters by operating at higher frequencies, temperatures and voltages, use of smaller and less passive components, such as transformers, inductors and capacitors, which makes power converters more compact and light-weight, ideal for space and weight-constrained applications, and compatibility with a wide range of …

Model-Based And Model-Free Control Approaches In Subgrids: A Conceptual Review Of Control Strategies In Microgrids, Omobolade H. Abioye

Theses and Dissertations

Increased reliance on the power grid and concerns over climate change issues have resulted in the rapid adoption of renewable energy technologies. Consequently, it is necessary to consider how renewable energy resources are combined and controlled. The microgrid serves as the control center for distributed energy resources. This thesis paper introduces the microgrid elements and framework, its control strategies highlighting frequency and voltage control, and the prospects of artificial intelligence for control, considering two significant approaches. Key components of sub grids like the energy management system (EMS) and energy storage systems (ESSs) are discussed, and lastly, the …

High-Power Dc-Dc Transformer For Medium-Voltage Grids With High-Voltage Sic Technology, Roderick Gomez

Graduate Theses and Dissertations

The objective of this dissertation is to present the theoretical analysis, design process, application and manufacturing of a proposed solid-state transformer intended for medium-voltage applications with minimal high-frequency oscillations. Galvanic isolation on medium-voltage DC-DC converters tend to employ large number of turns in the high voltage side of the transformers leading to non-negligible parasitic stray capacitances which form resonance tanks with the transformer inductances. Therefore, it is critical to estimate these parasitic capacitances to avoid severe high frequency oscillations which can significantly impact the converter performance. The main contribution of this thesis is the extension of a proposed custom-core design …

Phasor-Domain Short-Circuit Analysis Of Power Transmission Systems In The Presence Of Inverter-Based Resources, Dol Kunwar

All Theses

Although a power system is nonlinear during healthy operation because of constant power loads and controlled power injections from the sources, a conventional power system fed by synchronous generators is linear during fault, and can be represented by bus impedance matrix (Z-bus), which is useful in power system analyses such as short circuit (SC) analysis. However, With increasing penetration of inverter-based resources (IBRs) in the system, the assumption of linearity of the faulted network does not hold. This impacts the analyses relying on Z-bus and Thevenin’s equivalent impedance (TEI), such as certain protection schemes set using short circuit analysis. Therefore, …

Photovoltaics And Battery-Based End-To-End Direct Current Sustainable Power Networks- Concept, Design, And Control, Vishwas Powar

All Dissertations

The consequences of climate change have emphasized the need for a power network that is centered around green, low-cost, and renewable sources of energy. Currently, photovoltaics (PV) and wind turbines are the only two technologies that can convert renewable energy from the sun and wind, respectively, into large-scale power for the electricity network. This dissertation aims to provide a novel solution to implement direct current-based architecture for PV generation coupled with lithium-ion battery storage in an efficient and sustainable manner. Such a power network can enable efficiency, reliability, low cost, and sustainability with minimum impact on the environment. The first …

Real-Time Degradation Abatement Framework For Energy Storage System In Automotive Application Using Data-Driven Approaches, Laxman Timilsina

All Dissertations

The increasing popularity of electric vehicles (EVs) is driven by their compatibility with sustainable energy goals. However, the decline in the performance of energy storage systems, such as batteries, due to their degradation puts EVs and hybrid electric vehicles (HEVs) at a disadvantage compared to traditional internal combustion engine (ICE) vehicles. The batteries used in these vehicles have limited life. The degradation of the battery is accelerated by the operating conditions of the vehicle, which further reduces its life and increases the reliability and economic concerns for the vehicle’s operation. The aging mechanism inside a battery cannot be eliminated but …

Features Of Magnetoelastic Converters Of Mechanical Quantities Of Transformer Type, Sulton Amirov, Kamila Jurayeva

Chemical Technology, Control and Management

The article discusses the features of a magnetoelastic transformer type transducer. In magnetoelastic transformer-type transducers, mutual inductance is assumed as a variable value, which is a function of the value of the applied mechanical force. Hence, the transformation coefficients of such converters are also variable. There are also choke type converters in which a change in the magnetic permeability of the magnetic circuit leads to a change in the total electrical resistance of the choke. For further research, transformer-type converters were selected, which make it possible to widely implement techniques for improving basic characteristics.

Optimization Pump As Turbine Coupled To A Self-Excited Induction Generator Using Multi-Objective Genetic Algorithm, Emanuel J. Nyirenda

Tanzania Journal of Engineering and Technology (TJET)

As a way of accelerating the deployment of affordable and clean renewable energy generation technologies, applying a pump working as a turbine coupled to a self-excited induction generator is gaining popularity in various areas including energy recovery and micro hydro systems. However, it is currently challenging to predict the performance of the PAT-SEIG system and there is no agreed-upon rule on the selection of the appropriate system to be installed at a particular site. This paper has presented multi-objective optimization to select the best operating point of the PAT-SEIG system. The results show that the peak efficiencies for the PAT …

Optimal Load Shedding During Service Restoration In Electrical Secondary Distribution Network Based On Reinforcement Learning, Rukia J. Mwifunyi

Tanzania Journal of Engineering and Technology (TJET)

Increased stress in traditional power systems results in blackouts due to voltage instability attributed to a mismatch between available capacity and load demand, especially in distribution networks. Service restoration schemes are designed to return power supply to the affected parts of the networks. The availability of insufficient supply is a complex problem that requires operational experience or an automatic system. The stochastic nature of load demand significantly impacts service restoration as it results in increased restored demand in case a fault occurs during off-peak hours and helps reduce overload if the fault occurs during peak hours. The study adopts an …

An Optimization Tool For A Standalone Photovoltaic System, Johanes Kasilima

Tanzania Journal of Engineering and Technology (TJET)

Stand-alone photovoltaic systems (SAPV) are often used in remote areas where access to grid electricity is limited. This system depends on solar energy. However, Photovoltaic (PV) systems need a greater initial investment than conventional sources of energy, and their effectiveness is reliant on a number of environmental conditions such as the unpredictable solar radiation. One step in reducing the investment cost of a PV system is determining the optimal size of solar PV components that minimize costs. This paper presents a Particle Swarm based optimization tool for sizing Stand-alone PV systems. The optimization tool selects the optimal Levelized Cost of …

Surface Treatments' Effects On The Capacitor's Dielectric Performance Under Electro-Thermal Stresses, Haider. M. Umran, Feipeng Wang

Karbala International Journal of Modern Science

Biaxial-oriented polypropylene (BOPP) films are characterized by unfavorable aging behavior because of their poor susceptibility to high temperatures, humidity, and high electric fields. This makes them unqualified to withstand harsh operating conditions, such as in capacitor applications. This study investigates the impact of annealing BOPP samples at 100 °C for five hours after fluorination at different times (15, 30, and 60 minutes) on their electrical and mechanical performance under electro-thermal stresses. Scanning electron microscope (SEM) images confirm that there is an increase in surface roughness and the formation of a dense layer of fluorine-containing groups monotonically with fluorination time. So, …

Electrochemical Advanced Treatment Of Desulfurization Wastewater From Coal-Fired Power Plants, Ju-Cai Wei, Juan Yi, Xu Wu

Journal of Electrochemistry

Zero-emission of desulfurization wastewater is one of the main demands for coal-fired power plants. As typical high salinity wastewater, it is hard to purify the desulfurization wastewater from coal-fired power plants through traditional physicochemical treatment or biochemical treatment, e.g., COD and Cl^–. A high concentration of Cl^– ion in desulfurization wastewater restricts wastewater reuse and zero-emission. Electrochemical technology is an attractive method for high salinity wastewater zero-emission, which provides a versatile, efficient, cost-effective, easily automatable, and clean industrial process. For advanced treatment of effluent after triple box process treatment in power plants, this paper reports an electrochemical …