Power and Energy Commons^™

Feasibility Study Of Using Energy Extracted From The Process Of Electrochemically Consumed Of Al 2024 For Powering Daily Used Electric Car, Yanuar Mohamad Marda, Rini Riastuti, Muhammad Hamka Ibrahim

Journal of Materials Exploration and Findings

Usage of green energy for transportation has become important due to the contribution of transportation activity to climate change. Electrochemical energy has been used as a source of green energy. The objective of this work is to evaluate sufficiency of energy provided by electrochemically consumed Al 2024 for supplying energy to daily used PHEV electric car. Study of previous articles, observation of typical amount of energy required, electrochemical galvanic cell experiments, and simple calculations have been conducted to determine produced energy feasibility. Electrical energy produced by consuming 340 gr of Al 2024 in galvanic cells has the total lifetime of …

Fault Detection And Location In Renewable-Fed Distribution Systems Using Low Voltage Sensors, Bushra Farhat

All Theses

The penetration of Distributed Energy Resources (DERs) into the Electric Power System (EPS) is increasing. These (DERs) are mostly inverter-based resources (IBRs) that are integrated into (EPS) at the distribution level. Therefore, it has become necessary to leverage the integration of (IBRs) for both commercial and residential distribution systems through the deployment of Microgrid (MG). However, existing distribution systems that use fuses for sensing and isolating faults are not equipped to handle protection of microgrids where fault currents are fed from multiple sources and can flow downstream or upstream. Bulk of the protection schemes proposed in literature are heavily dependent …

Power Controller For Insulated Solar Electric Cooker, Ryan Koshy, Justin Tae-Hoon Kim

Electrical Engineering

Insulated Solar Electric Cookers, or ISECookers, are devices created to aid those in impoverished regions improve safety, sustainability, and quality of life regarding their cooking practices. ISECookers present an alternative to traditional biofuel/biomass energy sources and provide a closed-loop, self-sustaining system that can be used in a variety of environments. These devices present solutions to widespread issues such as pollution, deforestation, and hazardous emissions as a result of traditional cooking in developing regions around the world. A notable obstacle of these devices is power delivery. Given the varying conditions experienced by a solar panel (inclement weather, irradiance irregularities, etc.), it …

High-Power Power Conditioning Systems For Medium-Voltage Applications, Ahmed Rahouma Fares Rahouma

Graduate Theses and Dissertations

The purpose of this dissertation is to address the background, theoretical analyses, design methodologies, and evaluation techniques relevant to high-power power conditioning systems (PCSs) tailored for medium-voltage (MV) applications. Conventional PCSs, reliant on line-frequency transformers (LFTs), suffer from many problems including low power densities, inflexible designs, and scalability constraints. Employing multilevel converters (MLCs), particularly cascaded H-bridge topology, eliminates the need for these LFTs. A key focus lies in minimizing the number of cascaded building blocks by harnessing MV power switching modules. The dissertation makes two primary contributions: firstly, it offers a design methodology for MV-PCS, facilitating the selection of the …

Data-Driven Enhanced Energy Management System Applications For Energy Control Centers, Dulip Madurasinghe

All Dissertations

This dissertation explores the pressing needs of modern bulk power system operation and control and delves into enhancements to EMS applications with minimal infrastructure development. The dissertation investigates three main EMS application enhancements. The transmission network topology processing (TNTP) is a foundational application of the EMS. A physics-based hierarchical transmission network topology processing (H-TNTP), including substation configuration identification, to improve efficiency and reliability is proposed. Secondly, a multi-level distributed linear state estimation (D-LSE) approach solely based on PMUs is proposed utilizing H-TNTP as the network modeling tool. The D-LSE can conduct linear state estimation (LSE) at either substation, area or …

Time-Domain Line Protection In Presence Of Renewables, Prabin Adhikari

All Dissertations

Inverter based resources (IBRs) are crucial in integrating renewable energy sources into the power grid. However, their unique fault characteristics, significantly different from synchronous generators (SGs), present several challenges for existing line protection schemes at both transmission and distribution levels. These schemes, reliant on distance and directional relays designed in phasor domain, are not well-suited for IBRs. Most published literature addressing this problem concentrates on altering the control design of inverters. However, this approach faces practical limitations. Inverter controls, often proprietary, are not readily accessible to utilities, rendering the control-based solutions impractical for widespread implementation.

To address this challenge, this …

Evaluation, Modeling And Application Of Gallium Nitride Field Effect Transistor, Geno Guillaume

Graduate Theses and Dissertations

Gallium Nitride (GaN) has emerged as one of the leading materials for power devices due to its wide band gap and high electron mobility. The band gap is the minimum energy required to excite an electron up to a state in the conduction band where it can participate in conduction. Because of this, wide band gap (WBG) materials are favorable for various electrical applications. The market for GaN high-electron-mobility transistor (HEMT) is projected to exceed $1.25 billion by 2027. With the increase of market interest, modern technologies emerge that aim to push the boundaries of efficiency for GaN power devices. …

A Position Allocation Approach To The Battery Electric Bus Charging Problem, Alexander Brown

All Graduate Theses and Dissertations, Fall 2023 to Present

With an increasing adoption of Battery Electric Bus (BEB) fleets, developing a reliable charging schedule is vital to a successful migration from their fossil fuel counterparts. In this work, a BEB charging scheduling framework that considers fixed route schedules, multiple charger types, and battery dynamics is modeled as a Mixed Integer Linear Program (MILP). The MILP is modeled after the Berth Allocation Problem (BAP) in a modified form known as the Position Allocation Problem (PAP). The optimization coordinates BEB charging to ensure that each vehicle remains above a specified charge percentage. The model also minimizes the total number of chargers …

Thermal Management Of Roadway-Embedded Power Electronics For Electric Vehicle Dynamic Wireless Charging Systems, Conner R. Sabin

All Graduate Theses and Dissertations, Fall 2023 to Present

Electric vehicles (EVs) are gaining popularity worldwide. However, concerns raised by the public about purchasing EVs include the limited availability of charging infrastructure, high costs, and the inconvenience of current charging methods. Dynamic wireless charging systems enable electric vehicles to charge while driving, thereby extending the range of EVs and reducing the necessity for large, expensive batteries. Moreover, these systems can initiate charging automatically without user interaction, enhancing charging convenience.

The ground assembly of existing dynamic wireless charging systems consists of an electromagnetic assembly, power electronics for the transmitter pad, and power electronics for grid connection. Installation of these systems …

Series Reports From Professor Wei’S Group Of Chongqing University: Advancements In Electrochemical Energy Conversions (1/4): Report 1: High-Performance Oxygen Reduction Catalysts For Fuel Cells, Fa-Dong Chen, Zhuo-Yang Xie, Meng-Ting Li, Si-Guo Chen, Wei Ding, Li Li, Jing Li, Zi-Dong Wei

Journal of Electrochemistry

Two major challenges, high cost and short lifespan, have been hindering the commercialization process of low-temperature fuel cells. Professor Wei’s group has been focusing on decreasing cathode Pt loadings without losses of activity and durability, and their research advances in this area over the past three decades are briefly reviewed herein. Regarding the Pt-based catalysts and the low Pt usage, they have firstly tried to clarify the degradation mechanism of Pt/C catalysts, and then demonstrated that the activity and stability could be improved by three strategies: regulating the nanostructures of the active sites, enhancing the effects of support materials, and …

Data-Driven Viewpoint For Developing Next-Generation Mg-Ion Solid-State Electrolytes, Fang-Ling Yang, Ryuhei Sato, Eric Jian-Feng Cheng, Kazuaki Kisu, Qian Wang, Xue Jia, Shin-Ichi Orimo, Hao Li

Journal of Electrochemistry

Magnesium (Mg) is a promising alternative to lithium (Li) in solid-state batteries due to its abundance and high theoretical volumetric capacity. However, the sluggish Mg-ion conduction in the lattice of solid-state electrolytes (SSEs) is one of the key challenges that hamper the development of Mg-ion solid-state batteries. Though various Mg-ion SSEs have been reported in recent years, key insights are hard to be derived from a single literature report. Besides, the structure-performance relationships of Mg-ion SSEs need to be further unraveled to provide a more precise design guideline for SSEs. In this Viewpoints article, we analyze the structural characteristics of …

Professor Yong Yang, The Editorial Board Member Of Journal Of Electrochemistry, Is Elected As A Fellow Of The Electrochemical Society, Editorial Office Of J.Electrochem.

Journal of Electrochemistry

No abstract provided.

Kai Wu, The Editorial Board Member Of Journal Of Electrochemistry And Chief Scientist Of Catl, Receives The National Science And Technology Progress Award, Editorial Office Of J.Electrochem.

Journal of Electrochemistry

No abstract provided.

Sorbitol-Electrolyte-Additive Based Reversible Zinc Electrochemistry, Qiong Sun, Hai-Hui Du, Tian-Jiang Sun, Dian-Tao Li, Min Cheng, Jing Liang, Hai-Xia Li, Zhan-Liang Tao

Journal of Electrochemistry

The unstable zinc (Zn)/electrolyte interfaces formed by undesired dendrites and parasitic side reactions greatly hinder the development of aqueous zinc ion batteries. Herein, the hydroxy-rich sorbitol was used as an additive to reshape the solvation structure and modulate the interface chemistry. The strong interactions among sorbitol and both water molecules and Zn electrode can reduce the free water activity, optimize the solvation shell of water and Zn²⁺ ions, and regulate the formation of local water (H₂O)-poor environment on the surface of Zn electrode, which effectively inhibit the decomposition of water molecules, and thus, achieve the thermodynamically stable …

First Announcement Of 76th Annual Meeting Of The International Society Of Electrochemistry, International Society Of Electrochemistry (Ise)

Journal of Electrochemistry

No abstract provided.

Optoelectronic And Morphological Surface Resistance Evaluation Of Laser-Induced Graphene Counter Electrodes For Potential Applications In Cesium Lead Halide Perovskite Solar Cells, Ziad Khalifa, Sameh Osama Abdellatif, Rami Ghannam

Chemical Engineering

This study investigates the physicochemical, optical, and electrical characterization of laser-induced graphene (LIG) samples for integration as counter electrodes in cesium lead halide perovskite solar cells. The impact of laser processing parameters on electrode performance is explored, including laser power, laser speed, and beam defocus. Density functional theory (DFT) computational modeling is employed for atomistic investigation and work function estimation, demonstrating the density of states (DOS), quantum capacitance of the graphene sheets, and energy work function. NiO is utilized as a hole transport layer, and the energy work function of LIG is tuned accordingly. SEM measurements estimate thin film porosity, …

Experimental Validation Of An Analytical Transient Model For Saturated Boosting Gain In Dc–Dc Converters With Variable Duty Cycle, Goliana Samir, Simon Ezzat, Wagdy Anis, Sameh O. Abdellatif

Electrical Engineering

No abstract provided.

Control And Management Of The Balance Of Active And Reactive Power In A Power Supply System With A Solar Power Plant, Narzullo Nuriddinovich Mirzoyev, Siroj Sobirovich Nurov

Chemical Technology, Control and Management

This article discusses the development of a measurement and control system for monitoring and managing the balance of active and reactive power at power plants based on “Green” energy sources. Monitoring and management of the balance of active and reactive power based on a measurement and control system, calculated expressions are developed to solve the problem of reactive power compensation when transmitting electricity at power plants based on “green” energy sources. Reactive power is calculated based on measured active power, and combined reactive power sources generate the reactive power required by the network based on control signals. Schemes for connecting …

Surface Structures And Properties Of High-Voltage Licoo2: Reviews And Prospects, Jian-Jun Fang, Yu-Hao Du, Zi-Jian Li, Wen-Guang Fan, Heng-Yu Ren, Hao-Cong Yi, Qing-He Zhao, Feng Pan

Journal of Electrochemistry

Nowadays, the development of high-voltage LiCoO₂ (lithium cobalt oxide, LCO) cathodes has attracted the widespread attention from both the academic and industry fields. Among the multiple concerns, researches on the surface issues would provide the most effective performance optimization pathway for the synthesis of high-voltage LCO. In this work, the issues of high-voltage LCO, including the phase transitions and crack formation, the oxygen redox related issues and side reactions, as well as the surface structure degradation, have been systematically reviewed. Then, we further clarify the surface modulations, and the interplay between the surface modulation and electrolyte tuning. Finally, we …

In Situ Diffuse Reflectance Spectroelectrochemistry Of Cathode Materials In Lithium-Ion Batteries, Lu-Lu Chen, Hao-Ran Li, Wei-Yi Liu, Wei Wang

Journal of Electrochemistry

Developing in situ spectroelectrochemistry methods, which can provide detailed information about species transformation during electrochemical reactions, is very important for studying electrode reaction mechanisms and improving battery performance. Studying real-time changes in the surface of electrode materials during normal operation can be an effective way to assess and optimize the practical performance of electrode materials, thus, in situ and in operando characterization techniques are particularly important. However, batteries are hard to be studied by in situ characterization measurements due to their hermetically sealed shells, and there is still much room for battery characterizations. In this work, a specially designed battery …

Molybdenum Disulfide And Carbon Nanotubes Composite Electrode For Electrochemical Conversion Of Salinity Gradient Energy, Jia-Jun Li, Wei-Bin Zhang, Xin-Yu Liu, Jing-Lei Yang, Yi Yin, Ze-Qin Yang, Xue-Jing Ma

Journal of Electrochemistry

The ocean accounts for 97% of the total water resources on earth, covering over 70% of the map's surface area. With the continuous consumption of non-renewable energy sources such as fossil fuels and the rapid development of renewable energy, humans are increasingly paying attention to the utilization of ocean resources. Ocean energy includes tidal energy, wave energy, temperature difference energy, and salinity gradient energy. Salinity gradient energy is the energy generated by the interaction of seawater and fresh water, which is the ocean energy existing in the form of chemical energy. This energy is mostly generated in estuaries. The osmotic …

A Country-Level Primary-Final-Useful (Cl-Pfu) Energy And Exergy Database: Overview Of Its Construction And 1971–2020 World-Level Efficiency Results, Paul E. Brockway, Matthew Kuperus Heun, Zeke Marshall, Emmanuel Aramendia, Paul Steenwyk, Thomas Relph, Michelle Widjanarko, Jeonghoo (James) Kim, Anjana Sainju, Julian Irtube

University Faculty Publications and Creative Works

Societal exergy analysis examines the flows of energy and exergy through societies, from primary (e.g. oil) to final (e.g. gasoline) to useful (e.g. propulsion) energy stages. By extending the study of energy to the useful stage, new insights into the under-represented role of energy in economic growth have been made. However, currently (a) country coverage is patchy and incomplete, (b) available data are based on varying methods and assumptions including efficiencies based on economic rather than engineering data, and (c) datasets are constructed using piecemeal computational approaches. To address these gaps, we construct a country-level primary-final-useful (CL-PFU) energy and exergy …

Incremental Quantities Based Permissive Overreaching Transfer Trip Scheme For Protecting Inverter-Based Renewable Resources, Osama Zangoti

Electronic Theses and Dissertations

The power generation landscape evolves, with the increase of inverter-based resources (IBRs) such as solar photovoltaics and wind turbines, providing sustainable and clean energy sources. The shift towards IBRs mitigates climate change, creating considerable challenges to traditional power system protection due to their low fault current. Conventional protection schemes are designed around the internal dynamic of synchronous generators where they can supply an elevated fault current. This thesis explores a protection scheme designed to enhance the security of IBRs. The incremental characteristics of voltage and current coupled with the Permissive Overreaching Transfer Trip scheme (POTT) provide a remarkable ability to …

Harmonic Flow Modeling And Analysis Of A Green Hybrid Ac/Dc Seaport Power System, Krishan Kaushal Ram, Taufik, Helen Yu, Siddharth Vyas

Master's Theses

This thesis aims to design and develop a model for a proposed Green Seaport power system and perform harmonic analysis. The model was developed using MATLAB Simulink and tests were performed by dividing the system into several Battery Energy Storage System (BESS) operating modes such as simultaneous charging and discharging, simultaneous charging, and simultaneous discharging. For each mode, BESS state of charge and other factors such as solar irradiance for the PV system, load levels and power factor were varied to observe the impact on system’s voltage Total Harmonic Distortion (THD) level and current Total Demand Distortion (TDD). 62 separate …

Battery Energy Storage System, Alec C. Maclean, Kaylen H. Schwartz, Kyle A. Begley

Electrical Engineering

The project is a continuation of part 1 of the “Reliability Measurement for Grid-Connected Solar System” project. The goal is to continue where the previous design failed. This project will configure an ITECH IT-6000C and Tabuchi Battery Energy Storage System (BESS) to the small-scale microgrid at the Cal Poly, San Luis Obispo EE Department. Initially, a system was designed to connect an ITECH IT-M3633 as a PV solar source emulator to the Tabuchi BESS within a grid-connected microgrid system in Room 20-102 at Cal Poly. A Photovoltaic Thevenin equivalent model was developed for the ITECH IT-M3633, but this setup failed …

Advancing Embedded Iot Architectures For Space And Terrestrial Applications, Wuwei Douglas Liu, Nicolas Jesus Alvarez, Eric Huang

Electrical Engineering

Radio transceivers play a pivotal role in establishing communication networks, particularly in regions where existing infrastructures are unstable or compromised due to natural disasters or conflicts. By utilizing LoRa (Long Range) communication technology, OWL Integrations develops radio transceivers to establish mesh networks to communicate with one another during disasters. This project team continues development of a second generation OWL board, classified as Quacker Advanced Development (QuAD), with a focus on transitioning to a new microcontroller and integrating GNSS libraries and drivers. An ulterior objective involved R&D for a space application of the board.

Ross Dam Micro Hydropower Project, Ryan Pospichal, Wilson Szeto

Electrical Engineering

In 2020, Utica Water and Power Authority (UWPA) commissioned the development and installation of a micro hydropower system for Ross Dam in northern California. The micro-hydro system was intended to serve as a reliable source of renewable energy to power on-site equipment for monitoring the Ross Reservoir. Despite its innovative approach, the system encountered operational shortcomings, including frequent mechanical failures, rapid wear, and an inability to adapt to variable flow rates. To address these challenges, UWPA has commissioned interdisciplinary teams of Mechanical Engineering (ME) and Electrical Engineering (EE) students to redesign the micro hydropower system. The ME team was entrusted …

X-Band Wireless Power Transfer System Using A Focused Array Lens, Jason Alexander Kunz, Tyler S. Bury, Oscar Damian Gonzalez, Jaime Garcia

Electrical Engineering

Wireless power beaming from space and energy harvesting were once stories of science fiction, until now. Wireless power transmission (WPT) is a field continually in development to provide energy in situations where energy transfer through wires is impractical or unfeasible. This engineering discipline abandons the use of wire technology for the energy transfer between the power source and a distant device. While various forms of WPT exist, our project focuses on transmission through means of radio frequency (RF), utilizing electromagnetic waves to power devices. Furthermore, WPT technology primarily assists in the elimination of a physical connection between devices, and it …

Design Of High Efficiency Doherty Power Amplifier, Kobi G. Kelly, Severin Pindell

Electrical Engineering

The project includes design and fabrication of a high efficiency power amplifier for a student design competition held at International Microwave Symposium (IMS) 2023. Efficient power amplifiers are critical for base station communication requiring efficient use of available power. The final design optimizes power added efficiency (PAE) and linearity. The amplifier will operate at 2.45 GHz. Competitive PAE above 50%, and C/I above 30 dB is achieved by leveraging a Doherty class amplifier using accurate discrete CGH4006P transistor models to simulate an efficient and linear design. Unique design features include optimal transistor bias point selection and power split ratios between …

A 4-Switch Buck-Boost Dc/Dc Converter For Electric Vehicle Applications, Andrew Hudak, Ashley Schiller

Electrical Engineering

In this project, we develop a four switch buck-boost DC/DC converter that is to be integrated into a microgrid-inspired power distribution architecture for electric vehicles. The overall architecture includes DC/DC and DC/AC converters for bi-directional energy transfer between the DC and AC ports along with a communications port to control each energy interface. There is also the onboard battery and the internal combustion engine power exchange being done with DC/DC converters and AC/DC inverters to connect to the centralized DC bus. Hardware prototypes using an Arduino and Raspberry Pi for the 500 W DC/DC and DC/AC converters have been previously …