Power and Energy Commons^™

A Value Focused Thinking Model For The Development And Selection Of Electrical Energy Source Alternatives At Military Installations, Gregory T. Schanding

Theses and Dissertations

Electrical power on military installations is vital for mission accomplishment. Most installations obtain electrical power from a local commercial utility. Although commercial power service has a very low interruption rate, the threat of a sustained power outage resulting from a terrorist act or a natural disaster is of concern. The military should posture itself to prevent such power outages and prepare to mitigate the adverse effects associated with the loss of power. This thesis presents a Value Focused Thinking approach to the development of a decision analysis model to assist a decision maker at a military installation in the generation …

Progress In Research For Biofuel Cell, Yue Bao, Xia-Qin Wu

Journal of Electrochemistry

In this article, research progresses of the biofuel cell in recent years were summarized. The operation principle and classification of the biofuel cells were described. The role of the mediator for promoting electron transfer in biofuel cells and the techniques for improving the electric properties of biofuel cells, such as output potential, were discussed with some attracting research instances. Finally, the choke points for research of biofuel cell were explored, and the application prospect of biofuel cells was forecasted.

Preparation, Structure And Electrochemical Hydrogenation Of Carbon Nanotubes Supported Platinum Catalysts, Qing-Gang He, Xiao-Zi Yuan, Xian-Xia Yuan, Zi-Feng Ma

Journal of Electrochemistry

In this paper, Pt/CNTs catalyst was prepared and its electrocatalytic property was studied by obtaining cycling voltammetry curves (C-V) and Tafel curves. In addition, the XRD,XPS and TEM tests were carried out to determine the structure and composition of the catalysts. It can be found that the platinum loading has been increased significantly using a carbon nanotubes support. Dispersion of Platinum was better and gave more active sites. The electrochemical characteristic of Pt/CNTs was also more desirable than that of Pt/C catalys t(Johnson Matthey). In conclusion, carbon nanotubes can played a conspicuous role in "electrogenerative" processes of PEMFC hydrogenation reactor.

Template Synthesis Of Highly Ordered Monocrystalline Metal Nanowire Arrays By A Two-Step Ac Electrodeposition, Juan Xiang, Jing-Hua Tian, Zi-Mian Ni, Zhi-Feng Huang, Bo Liu, Zhong-Qun Tian

Journal of Electrochemistry

The monocrystalline metal nanowire arrays were prepared by using a two-step AC electrodeposition in porous anodic aluminum oxide (AAO) template. The growth mechanism of nanowires was discussed. As a result, it has been found that the second voltage pulse has a considerable effect on the pore-filling ratio, the uniformity and the crystal structure, whereas the initial voltage pulse affects only the pore-filling ratio. Using the two-step AC electrodeposition, a highly ordered monocrystalline metal nanowire arrays with a pore-filling ration above 95% can be easily obtained.

The Interaction In Doping Lithium Of Carbonaneous Anode In Lithium Ion Battery, Chang-Guo Chen, Hong-Min Zhang, Jia Chen, Dan-Mei Yu

Journal of Electrochemistry

The quantum chemical DV-X_α method was used to calculate the lithium-doped models from one-Li-dopant to LiC₆ and LiC₂. It was found that Li⁺ has an tendency to attract electrons from the carbon plane through the C₆ hexagons lying above or below it by the graph of charge-density difference. It was shown that LiC₆ can exist steadily,while LiC₂ can not exist steadily.

Study On Determination Of Iodine Ion At Chitosan Modified Glassy Carbon Electrode, Bin Liu, Xiang-Ying Sun, Jin-Rui Xu

Journal of Electrochemistry

In this paper, a chitosan modified glassy carbon electrode was prepared by the method of covalent-bond reaction, and the anodic stripping voltammetric characteristics of iodine on the modified electrode was studied. The results showed that the modified electrode has higher adsorption and selectivity for I^- , and the sensitivity for I^-  has been much improved in 0.1 mol·L^-1 KH₂PO₄ solution (pH=4.0). The anodic stripping peak current of I^- on the modified electrode varied linearly with I^-  concentration in the range of 2.0×10^-6～2.0×10^-3 mol·L^-1, and the detection limit …

Electrochemical Synthesis Of Ferrate(Vi) By Anodic Oxidation, Jia-Ju Xu, Jian-Ming Wang, Wei-Hua Yang, Cheng Chen, Jian-Qing Zhang

Journal of Electrochemistry

The ferrate(Ⅵ) was synthesized by electrochemical anodic oxidation. The effects of preparation conditions on the current yield of ferrate(VI) synthesis have been studied in this work. The experimental results showed that grey cast iron as an anodic material is suitable for electrochemical synthesis and NaOH solution as an electrolyte results in a higher current yield than KOH solution. The highest current yield was obtained at a current density (4.54) mA·cm^-2, temperature 20 ℃ and 14 mol·dm^-3 NaOH. In this case, a current yield of 68.5% was obtained by electrolysis for 1 h.

Studies On The Mechanism Of Electroreduction Of Oxalic Acid, Yu-Zhan Li, Xin Liu, Rui-Sheng Hu, Deng-Ping Gu

Journal of Electrochemistry

The electroreduction mechanism of oxalic acid on Pb electrode in Na₂SO₄ solution were investigated using high scan rate cyclic voltammetry and chronoamperometry. The dynamic parameters for the first step electron transter reaction of oxalic acid electroreduction by were determined. The corresponding reduction peak potentials of oxalic acid, glyoxylic acid and glycolic acid in the cyclic voltammogranis obtained in the same condition were compared, and the intermediate reduction products of oxalic acid were suggested. The results showed that oxalic acid is weakly absorbed on the lead electrode.

Electrochemical Character Of Water Containing Gel Electrolyte And Its Preliminary Examination In Lithium Water Cell, Jing-Dong Liu, Wen-Ji Wang, Xin-Zheng Yi

Journal of Electrochemistry

AC impedance technique has been used to characterize the system of poly(methyl acrylic acid)-poly(methyl acrylic lithiumate)-glycerol (referred to as GPE).The results showed that the conductivity of GPE increased with increasing both temperature and its water content.The glass transition temperature of GPE polymer could be lowered by water. Its conducting characteristic was just like liquid electrolyte,The electrolysis of GPE was almost the same as the electrolysis of water. Its composition voltage was about 1.50V. The GPE has been used to manufacture lithium water cell. When the graphite was used as cathode, the cell could discharge continuously for 2 hours under constant …

Compact High-Voltage Generator Of Primary Power Based On Shock Wave Depolarization Of Lead Zirconate Titanate Piezoelectric Ceramics, Sergey I. Shkuratov, Evgueni F. Talantsev, Latika Menon, Henryk Temkin, Jason Baird, Larry L. Altgilbers

Mining Engineering Faculty Research & Creative Works

The design and performance of a compact explosive-driven high-voltage primary power generator is presented. The generator utilizes a fundamental physical effect—depolarization of ferroelectric materials under longitudinal shock wave impact, when the shock wave is initiated along the polarization vector P. These primary power sources, containing energy-carrying elements made of lead zirconate titanate poled piezoelectric ceramics, with the volume from 0.35 to 3.3 cm3, are capable of producing pulses of high voltage with amplitudes up to 21.4 kV. The amplitude and full width at half-maximum of the high-voltage pulses are directly proportional to the thickness of the energy-carrying element, with coefficients …

Optimisation Of Heat Transfer And Fluid Flow In The Cooling Of Building Integrated Photovoltaic Facades., Eoin Patrick Hodge

Theses

The aim of this research was to explore the effects of mature and developing technologies from aeronautical industries such as impingement and film cooling, and electronic cooling techniques, in the setting up of different laminar and turbulent flow regimes on PV cooling duct heat transfer rates, with air flow as that brought about with natural buoyancy effects in a vertical building facade. The problem of efficiency losses in PV panels, due to overheating, is one of the factors restricting the development and use of this renewable power source. PV panels can experience very high temperatures, due to the heat input …

Load Flow Solution For Three-Phase Mv Radial Distribution Connected Network Supplying Different Line Topologies, B. J. Kundy

Tanzania Journal of Engineering and Technology (TJET)

In this paper, a load flow solution for the Medium Voltage (MV) three-phase radial distribution in delta-delta (Δ–Δ) connected network supplying different line topologies such as three phase, phase to phase and single-wire earth return (SWER) networks is presented. The general voltage related network equations are developed using Kirchhoff’s voltage and current laws. Development of a solution to the load flow analysis applying the developed general voltage related network equations is proposed in order to evaluate the network voltage profile. Various numbers of arrays are developed for the identification of the network under study. The proposed method is a new …

Preparation And Characterization Of Y-Type Carbon Nanotubes By Using Anodized Alumina Oxide (Aao) Template, Jing Zhang, Quan-Yong Gao, Yong Yang

Journal of Electrochemistry

In this work, potential-modulation method was used in two-step anodization process to make an AAO template with Y-type nanochannels. Then Y-type carbon nanotubes with controlled length and branch angle were prepared in the template based on chemical vapor decomposion (CVD) method with Co particles as catalyst and C₂H₂ as carbon source. The Y-type nanotube branches exhibit the angle distribution ranging from 20° to 120°. The results demonstrated that the oxidation potential should be responsible for the angles and length of the branches. Short pulse and high oxidation potential will result in the short and dense nanotube branches.

Study On The Gas Generation In Different Charging Voltage During Formation Process In Polymer Lithium-Ion Battery, Li Huang, Ming-Gang Jin, Hui-Qun Cai, Ming-Sen Zheng, Quan-Feng Dong, Jin-Kua You, Zu-Geng Lin

Journal of Electrochemistry

The gases of polymer lithium-ion battery (PLI) generated under different voltages during the first charging process were examined by means of gas chromatography (GC), and the mechanism of the gas generation was discussed. The electrolyte used in batteries was 1 mol/L LiPF₆-EC～DMC～EMC=1∶1∶1(in volume). The results showed that when the charging voltage is less than 2.5 V,  the main component of generated gases are H₂ and CO₂, and when the charging voltage is 2.5 V, EC begins to decompose. Due to the decomposition of EC, the main generated gas is C₂H₄ when the …

Application Of Hydrogen-Storage Alloy Electrode In Electrochemical Reduction Of Glucose, Hui Chen, You-Gen Tang, Zheng Tang

Journal of Electrochemistry

Electrolysis of glucose was performed at constant potential using hydrogen-storage alloy as catalytic reduction electrode. It was found that the superficial treatment and activation of hydrogen-storage alloy powder had obvious effects on improving the current efficiency of sorbitol. Under the optimums, current efficiency of sorbitol by electrolyzing glucose was over 94%. The yield of sorbitol was over 80%, the lifespan of electrode was tested and analyzed, the ways of regeneration were discussed.

Study On Degradation Of Phenol By Electrochemical Oxidation, Yue-Li Liu, Hong-Hua Ge

Journal of Electrochemistry

Electrochemical oxidation of phenol was carried out by the Dimensionally Stable Anodes (DSA) electrode, which has been discarded as waste by alkali chloride factory. The result indicates that a good phenol removal can be obtained under certain phenol concentration by the DSA electrode. The key factor in effecting phenol removal of electrochemical oxidation is applied current density, the following factors are pH, electrolyte concentration and phenol concentration. After experiments, the optimal test conditions are 30 mA/cm², pH 10, electrolyte concentration 10 mg/L, phenol concentration 10 mg/L.67% CODcr removal and 90% absorbance removal are gained by electrochemical oxidation for …

Optimizing Catalyst Layer Composition Of Pemfc By Orthogonal Method, Ming-Hua Wang, Xin-Jian Zhu, Guang-Yi Cao, Sheng Sui, Qing-Chun Yu, Ming-Ruo Hu, Zheng-Yu Fan

Journal of Electrochemistry

The optimal composition of catalyst layer in a PEMFC electrode was studied through orthogonal method. It was showed that the performance of hydrophilic electrodes, in which there is no PTFE in the catalyst layer, were more favorable than that of hydrophobic electrodes. According to this condition, the power density of PEMFC attained 0.37 w·cm^-2 when the Nafion loading was 1.4 mg·cm^-2, and the Pt loading was 0.4 mg·cm^-2 in the catalyst layer, using H₂ as fuel and air as oxidant both at atmospheric pressure. Additionally, the results showed that increasing Pt loading in Pt/C catalyst …

The Study On Carbon Nanotube-Loaded Pt Catalysts For Proton Exchange Membrane Fuel Cells, Hong Zhu, Feng-Juan Ge, Xiao-Hong Kang, Yu-Guo Yang, Yun-Hua Xu

Journal of Electrochemistry

Carbon nanotube-supported-platinum (Pt/CNTs) and carbon-supported-platinum (Pt/C) catalysts were synthesized by in-situ chemical reduction. They were analyzed using TEM and XRD, then made into electrodes to be part of assemable PEMFC for the performence tests. The resulted show that Pt clusters in both catalysts are of small particle size (about 4nm), and Pt/CNTs exhibits a higher catalytic activity than Pt/C.

The Current Fluctuations Of Carbon Steel In Nano2-Nacl Solutions, Yu-Ming Tang, Yu Zuo

Journal of Electrochemistry

The characteristics of current fluctuations of A3 carbon steel in NaNO₂-NaCl solutions were studied with potentiostatic and potentiodynamic polarization methods. The steel remained stable passivation in 0.1 mol/L NaNO₂ solution without Cl^-. After NaCl was added in to the solution, current fluctuations with a characteristic of quick increase and slow decrease occurred, indicating quick dissolution and slow re-passivation of the metastable pits. The metastable pitting may cause accumulated corrosion damage around certain area and result in observable pits. With the increase of chloride concentration, the occurring potential for metastable pits Em rised, and peak values …

Adsorption And Oxidation Of Phenol Electrode Processes, Bao-Cheng Wang, Yan-Ping Sun, Jin-Hua Zhu

Journal of Electrochemistry

The electrochemical behaviors of platinum electrode were studied by cyclic voltammetry in 1mol/L sulfuric acid solution and 1mol/L sulfuric acid solution contained phenol. The adsorption characteristics of phenol and the intermediat on electrode surface have been discussed. The reactive reversibility and oxidation mechanism of phenol on electrode process have been investigated.The potential of characteristic adsorption was suggested. The various products woud be formed when the electrode potential was greater than the one of characteristic adsorption.

Synthesis And Electrochemical Properties Of K2Feo4, Ning Zhou, Shi-Hai Ye, Yong-Long Wang, Xue-Ping Gao, Dong-Feng Lin, Zuo-Xiang Zhou, De-Ying Song

Journal of Electrochemistry

The K₂FeO₄ used for new positive electrode materials was prepared. The primary batteries were used in different concentration of electrolyte and different currents. In 9 mol/L KOH , the capacity was the best. The higher the concentration of electrolyte, the lower the electric potential was. When the batteries discharged in 0.4 C , the capacity reached 521.3 mAh/g. By XRD, we gave the reasonable explanations for the discharge products of K₂FeO₄. Possible mechanism of discharge is discussed.

Comparison Of Thermal Cyclic Oxidation Of The Pvd Ni-Al And Hvof-Mcraly Coatings, J-T Chang, C-H Yeh, J-L He, K-C Chen

Journal of Electrochemistry

A PVD process-cathodic arc plasma ion plating was used to deposit Ni-Al films on Inconel 600 superalloy. The oxidation behaviors of PVD Ni-Al coating and the thermal sprayed CoCrAlY coatings were revealed and compared by performing cyclic thermal oxidation test at 1100 ℃ to evaluate its feasibility. Experimental results showed that the films with different compositions of Ni₆₂Al₃₈, Ni₆₃Al₃₇ and Ni₆₉Al₃₁ could be obtained when using Ni₅₂Al₄₈, Ni₆₀Al₄₀ and Ni₇₀Al₃₀ as targets, respectively. During the cyclic thermal oxidation test, the …

Effect Of Heat Laminating Aggregation Status Of Polymer Lithium-Ion Battery Cathode On Battery Performance, Ming-Gang Jin, Quan-Feng Dong, Ming-Sen Zheng, Li Huang, Hui-Qun Cai, Jin-Qua You, Zu-Geng Lin

Journal of Electrochemistry

Multi-layer heat laminated polymer lithium ion battery was made, the effect of temperature of cathode laminating on battry performance was also investigated. It was discovered that suitable temperature of cathode laminating is critical to battery performance and is a key parameter to manufacture process control of polymer lithium ion battery.

Electrochemistry And Electrocatalysis Of A Novel Μ-Oxamido Copper(Ⅱ) Binuclear Complex, Gui-Lian Gao, Guo-Bao Li, Qiu-Xia Yang, Xue-Lin Wang

Journal of Electrochemistry

In this paper, the cyclic voltammetric and spectroelectrochemical behaviors of μ-oxamido Copper(Ⅱ) Binuclear Complex (deCu) in PBS were studied. Cyclic voltammograms of this complex in PBS (pH=9) exhibited two reductive peaks (E_pc1 =-0.25 V, E_pc2 = -0.50 V) at hanging mercury drop electrode(HMDE), peaks at -0.50 V and -0.25 V corresponded to the reduction of ligand and copper(Ⅱ) complex, respectively. The spectroelectrochimical experiments showed that there was a new absorption band at 440 nm, and the absorption peaks at 270 nm, 280 nm red shifted to 300 nm, 310 nm under potential of -0.75 V. It was meant …

The Mechanism Of Electrocatalytic Reduction Of Oxygen On Manganese Dioxide, Yu-Liang Cao, Han-Xi Yang, Xin-Ping Ai, Li-Fen Xiao

Journal of Electrochemistry

The oxygen electroreduction on the MnO₂ electrode was investigated by analysis of the polarzation properties of oxygen reduciton and its dependence on MnO₂ discharge state, in combination with the characterization of discharge intermediate and the kinetic parameters of the oxygen reduction. Based on the experimental observation and mechanistic analysis, it was suggested that the reduction of oxygen was closely related to the discharge behaviors of MnO₂. When MnO₂ was electrochimically reduced to MnOOH, it was immediately oxidized by oxygen molecules. Thus the oxygen reduction proceeds through continuous oxidation of the discharge product of MnO_{2 …}

Synthesis Of Polyunit Vapor Phase Inhibitor And Its Volatile Corrosion Inhibition Performance, Da-Quan Zhang, Li-Xin Gao, Guo-Ding Zhou

Journal of Electrochemistry

A Mannich Base derivative (BMMCH), containing two morpholinum moieties and one cyclohexylamnonium moiety, was synthesized through aminomethy1 reaction. Its configuration was verified by IR and ¹H-NMR. Its volatile rustproofing effect was appraised by volatile rustproofing sieve test and vapor inhabitability test. The result shows that BMMCH has good protection effect for carbon steel. BMMCH has lower volatility compared with dicyclohexylamnonium nitrite (DICHAN) via closed space volatile weight-loss test. The inhibition mechanism was studied by potentiodynamic polarization electrochemistry technique in ASTM simulated atmospheric water. The corrosion potential of carbon steel electrode shifted to a negative direction when BMMCH was joined …

Day 5. Friday, August 15, 2003: Rocky Mountain National Park, University Of Colorado Boulder. Natural Resources Law Center

Energy Field Tour 2003 (August 11-16)

1 page.

Contains references.

Day 4. Thursday, August 14, 2003: Hayden Power Plant, University Of Colorado Boulder. Natural Resources Law Center

Energy Field Tour 2003 (August 11-16)

5 pages (includes color illustrations and maps).

Contains references.

Day 4. Thursday, August 14, 2003: Trapper Mine, University Of Colorado Boulder. Natural Resources Law Center

Energy Field Tour 2003 (August 11-16)

8 pages (includes some color illustrations).

Contains references.

Day 3. Wednesday, August 13, 2003: Oil Shale, University Of Colorado Boulder. Natural Resources Law Center

Energy Field Tour 2003 (August 11-16)

8 pages.

Contains references.