Power and Energy Commons^™

Applications Of New Activated Carbon Meterials In The Electric Double-Layer Capacitor, Jian-Jun Zhang, Hua Jiang, Jian-Hui Fang, Li-Yi Shi, Ren-He Yin, Yi Wen, Ji-Quan Liu

Journal of Electrochemistry

A new type activated carbon whose precursor was coconut shell could be obtained using specific physics-chemistry activation, and the activated carbon was applied as the material of electrode in EDLC (electrical double-layer capacitor),which had a large specific capacitance, and could charge and discharged in some large currents. Carbon dioxide and acid were used to modify carbon,and the effects of post-treatment on surface area and pore volume were investigated. A moulding method which has influence on some properties of carbon electrode with PTFE additive was researched in the paper.

Effect Of Fe3+ Dopen Of Titanium Dioxide Film On Absorption Spectra And Photo Catalysis, Mei-Qun Xiao, Jia-Nian Shen, Moucheng Li, Peng-Fei Wu, Dong Liu, Yu-Juan Zhang

Journal of Electrochemistry

Photo-catalytic titanium dioxide film in nano crystalline has been prepared by electrochemical oxidation process and adding different amount of ferric ion into the electrolyte during the anodic oxidation.The effects of Fe³⁺ dopen on absorption spectra and photo-catalytic of the titanium dioxide films have been studied. It shows that the Fe³⁺ dopen caused the red shife of the absorption edge for the incoming light and exhibited the improved photocatalytic reactivity.

Anodic Dissolution Of Aluminum In Koh-Ethanol Solutions, Hai-Bo Shao, Jian-Ming Wang, Xiao-Yan Wang, Yi Zheng, Jian-Qing Zhang

Journal of Electrochemistry

The feasibility of employing aluminum in KOH ethanol solution as a battery anode system was discussed. Weight loss measurement showed that the corrosion rate of Al is low enough to be used in sealed batteries. Through the measurements done by anodic polarization, EIS and galvanostatic discharge, it was found that Al is electrochemical active in a wide potential range in this system, and its discharge mechanism is similar to that of Al in aqueous solution. The discharge potential increased rapidly after a period of time, which might be caused by the discharge products depositing on the electrode surface.

Preparation And Photo-Catalyst Properties Of The α-Fe2O3-Tio2 Films On Sodium Alginate Polymer, Li-Qin Chen, Huai-Zhen Zhong, Ri-Yao Chen, Xi Zheng, Zhen Chen

Journal of Electrochemistry

Three new nano thin films of α-Fe₂O_3, TiO₂ and α-Fe₂O₃-TiO₂ by doping their powder with sodium alginate polymer were prepared. Surface structure and catalytic activities of the films were characterized by FTIR, XRD, PL, TEM and I-V techniques. The results of UV-visible absorption showed that the methylene blue was mineralized in aqueous of α-Fe₂O₃/SA, TiO₂/SA and (α-(Fe₂O₃))-TiO₂ /SA upon radiation with ultra violet light. α-Fe₂O₃ enhanced their photo-decolorized-activities by doping 15% TiO₂.

A Dual-Cell Technique And Its Application In Electrocatalytic Study Of Pt-Ru Metals, Lei Su, Bing-Liang Wu

Journal of Electrochemistry

Two local electrochemical reactive interfaces are established using two strips of Nafion membrane separated each other, which are in contact with different surface regions of the same metal-sheet working electrode. One potentiostatis used to control thepotentialof one electrochemical reactive interface to generate adsorbed surface speciesand the other potentiostatto hold the potential of the second interface as a detector of the intermediate. The adsorbed surface species driven by the difference in surface concentration diffuses alongthe surface of the metal-sheet between both local electrochemical interfaces and can be detected at the second interface when they achieveover there.The surface diffusion coefficient of the …

Electrochemical Reduction Of Nitrobenzene On The Wc Electrode In Acidic Solution, Chun-An Ma, You-Qun Chu, Ying-Hong Zhu, Zhi-Hua Xu

Journal of Electrochemistry

The tungsten carbide (WC) electrode was constructed by using polyterafluoroethylene as binder. The electrochemical behavior of nitrobenzene on the WC electrode in acidic solution was investigated by cyclic voltammetry, linear scan method and chronoamperometry. Experimental results showed that WC electrode had good activity for the electrochemical reduction of nitrobenzene, and the electrode process was controlled by diffusion and electrochemical stepssimultaneously. The apparent active energy of the electrode process is 23.7kJ⋅mol^-1, while the active energy of the electrochemicalstep is 10.91kJ⋅mol^-1.

Synthesis Of (S)-3-Phenylpropane-2-Tert-Butoxycarbonylamino-1-Thiol And Its Electrochemical Behavior Self-Assembled On Gold, Ru Sun, Jian-Feng Ge, Mei Wang, Ren-Ao Gu

Journal of Electrochemistry

The synthesis of (S)-3-Phenylpropane-2-tert-butoxycarbonylamino-1-thiol(N-Boc-APT) from L-phenylalanine was reported. L-Phenylalanine was reduced to the corresponding amino alcohol, protection of the amino group using tert-butyl pyrocarbonate gave (S)-2-tert-butoxycarbonylamino-3-phenylpropane-1-ol, which was then O-mesylated and treated with potassium thioacetate in DMF to give 3-phenylpropane-2-tert- butoxycarbonylamino-1-etylmercapto. After the acetyl group was removed with ammonia in alcohol, the desired target molecular was obtained. The structure of intermediate and target molecular was conformed by IR and ¹HNMR. We made N-Boc-APT self-assemble-modificated gold electrode and investigated its electrochemical behavior. The CV results of methylene blue on nano-Au/N-Boc-APT SAM/Au electrode showed that nano-Au could speed this electron transfer …

Solid State Synthesis And Electrocatalysis Of Pt/Moo3 For The Oxidation Of Methanol, Qing Wang, Yi-Ming Zhou, Yang Shao, Yi-Gang Ji, Juan Xu, Ya-Wen Tang, Tian-Hong Lu, Tao Shen

Journal of Electrochemistry

The electrocatalyst, Pt/MoO₃ synthesized by solid state reaction, was used for the oxidation of methanol in direct methanol fuel cells. The X-Ray diffraction and cyclic voltammetry were employed to investigate the performance of the material. It was shown that the typical diffraction peaks for Pt appeared in XRD. And a good electrocatalysis for methanol oxidation was observed. The peak potential of the methanol oxidation appeared at ca. 0.63V(vs.SCE) and the peak current density for the oxidation was 78.1 mA⋅cm^-2.

Synthesis And Electrochemical Behavior Of Layered-Structure Limn1-XCrXO2, Jie Xiao, Hui Zhan, Yun-Hong Zhou

Journal of Electrochemistry

The Layered-structure LiMn_1-xCr_xO₂(x=0, 0.15) solid solution has been prepared by the rheological phase method. From the XRD results, undoped LiMnO₂ crystallized almost entirely in the orthorhombic phase while the structure of LiMn_0.85Cr_0.15O₂ belongs to monoclinic phase. TEM investigation shows that the final powder product consists of ultrafine spherical particles which are distributed homogeneously, with the average diameter ranging from 60 to 300nm. The initial discharge capacity of LiMn_0.85Cr_0.15O is much higher than that of undoped LiMnO₂. After 40 cycles, the capacity retention …

Synergisms Of Electric Or Electromagnetic Fields And Photodynamic Effects Induce Apoptosis And Necrosis Of Cancer Cells, Radeva Maria, Lambrera Maya, Angelova Plamena, Traitcheva Nelly, Berg Hermann

Journal of Electrochemistry

Weak pulsating sinusoidal electromagnetic fields (PEMF) have been applied to change membrane permeation and induction of apoptosis (necrosis). In the case of suspension of human cancer cells U-937 and K-562 inside of Helmholtz-coils the amplitude of PEMF B=10 and at 39mT (at 50 Hz) was combined gradually with the cytotoxic agent actinomycin-C on one hand with its novel photodynamic activity on the other.

Preparation And Electrochemical Performance Of New Composite Seperators For Lithium-Ion Batteries, Hu Cheng, Hong-Yan Du, Yong Yang

Journal of Electrochemistry

New composite seperators for lithium ion batteries were prepared by coating PEO mixed with nanosize SiO₂ onto microporous polypropylene(PP) seperators. Highly conductive electrolytes were prepared by soaking them in an electrolyte solution. With these composite separators, the lithium ion cell consisting of Li anode and LiNi_0.8Co_0.2O₂ cathode were assembled. The high initial discharge capacity and good capacity retention were obtained through the cell.

Lithium Insertion Into Tio2(B) Nanobelts Synthesized By The "Soft Chemical" Method, Cha-Geng Nie, Zheng-Liang Gong, Lan Sun, Juan Zuo, Yue-Kun Lai, Chang-Jian Lin

Journal of Electrochemistry

TiO₂(B) Nanobelts were synthesized by using the "Soft chemical"method. The products were characterized by means of transmission electron microscope(TEM), X-ray diffraction(XRD), Raman spectrum and energy dispersive spectrum(EDS). Galvanostatic charging and discharging tests showed that lithium-ion intercalation/deintercalation occurred reversibly in the TiO₂(B) nanobelts electrode, and a high capacity (265 mAh·g^-1) can be obtained. The results suggested that TiO₂(B) Nanobelts might be a promising negative electrode material of second Lithium battery.

Preliminary Study Of Speek Membranes For Direct Methanol Fuel Cells Application, Su-Zhen Ren, Zhen-Xing Liang, Xin-Sheng Zhao, Qin Xing, Gong-Quan Sun, Xue-Feng Yang

Journal of Electrochemistry

This paper describes the methanol permeability characterization of SPEEK membranes and their feasibility for DMFC application. The SPEEK membranes showed a significant lower methanol permeation than Nafion 115 determined from voltammetric methods. An increase in open circuit voltage was found in the performance of SPEEK membranes in DMFC. The power density of the cell using SPEEK membrane was considerably poorer than that of Nafion 115. If modified properly, the SPEEK membranes can be chosen for DMFC application based on this study.

Fabrication Of Solid Oxide Fuel Cells And Analysis Of Their Structure And Performance, Nai-Tao Yang, Bo Meng, Ru-Jun Yu, Xiao-Yao Tan

Journal of Electrochemistry

An intermediate temperature solid oxide fuel cell (IT-SOFC) was fabricated by co-copressing-sintering methods, and the electrolyte of Ce_0.8Gd_0.2O_1.9 (CGO) and cathode materials of La_0.6Sr_0.4Co_0.2Fe_0.8O_3-α (LSCF) were prepared by sol-gel method. The effect of preparation methods on the microstructure of the prepared fuel cells was analyzed by SEM . It shows that the cells prepared by the co-pressing/co-sintering method possess a dense electrolyte layer and a compact interface between electrolyte and anode but a curved configuration, while those prepared by the colloidal technique have a flat configuration …

Study On An Intermediate Temperature Planar Solid Oxide Fuel Cell, Shao-Rong Wang, Wen-Xia Chen, Ting-Lian Wen, Jia-Di Cao, Zhi-Yi Lv, Da-Qian Wang

Journal of Electrochemistry

Tape cast method was applied to prepare green sheets of Ni/YSZ anode supported YSZ thin film. After isostatic pressure treatment and cosintering, the YSZ film on the Ni/YSZ anode was gas-tight dense, and 15~30 μm thick. The area of the composite film was over 100 cm². A Ce_0.8Sm_0.2O_1.9 (CSO) interlayer was sintered on to the YSZ electrolyte film to protect La_0.6Sr_0.4CoO₃ (LSCO) cathode from reaction with YSZ at high temperatures. The LSCO cathode layer was screen printed onto the CSO interlayer and sintered at 1200 ℃ for 3 …

Day 3: Friday, August 6, 2004: Cbm And Unconventional Gas Development, Gary Bryner, Ken Wonstolen

Energy Field Tour 2004 (August 4-6)

19 pages (includes illustrations and maps).

Day 2: Thursday, August 5, 2004: Valmont Power Plant, Valmont Power Plant

Energy Field Tour 2004 (August 4-6)

5 pages (includes illustrations).

Day 2: Thursday, August 5, 2004: Xcel Energy Lookout Dispatch Center, Doug Larson, United States. Department Of Energy

Energy Field Tour 2004 (August 4-6)

7 pages (includes illustrations and maps).

Agenda: Energy Field Tour 2004, University Of Colorado Boulder. Natural Resources Law Center

Energy Field Tour 2004 (August 4-6)

Tour (day trips along the Front Range, originating in Boulder) held August 4-6, 2004.

Summary: Assorted articles, maps, brochures, and other materials prepared for participants of the tour

Contents:

2004 energy field tour agenda -- Mission and vision of the Natural Resources Law Center -- Natural Resources Law Center, University of Colorado School of Law : a brief introduction -- Boulder area street map 4 -- Chatauqua area map -- [Bus] Route 203/225 : Boulder/Lafayette/Baseline -- Boulder-Lafayette via Baseline [bus schedules]

WEDNESDAY, AUGUST 4, 2004: OIL & GAS PRODUCTION FACILITIES AND PLATTEVILLE GAS PROCESSING FACILITY: 'Our next shortage', The Washington …

Day 1: Wednesday, August 4, 2004: Ponnequin Wind Farm, Western Resource Advocates

Energy Field Tour 2004 (August 4-6)

2 pages (includes illustration).

Day 1: Wednesday, August 4, 2004: Oil & Gas Production Facilities And Platteville Gas Processing Facility, Bruce Thompson

Energy Field Tour 2004 (August 4-6)

12 pages (includes illustrations and map).

Day 1: Wednesday, August 4, 2004: Calpine Rocky Mountain Energy Center, Calpine Rocky Mountain Energy Center

Energy Field Tour 2004 (August 4-6)

5 pages (includes illustrations).

Review Of The Product Development Process And Information Flow In The Manufacturing Industry: Problems And A Possible Wav Forward, E Opiyo

Tanzania Journal of Engineering and Technology (TJET)

No abstract provided.

Preparation, Characterization And Photoelectrochemical Activities Of Cu-Tio2/Ito Films, Dong Shu, Chun He, Han-Xia Zhang, Ya Xiong

Journal of Electrochemistry

Cu-TiO₂/ITO films were prepared by direct photo-reduction deposition of Cu²⁺ on TiO₂/ITO films. The nanocomposite films were characterized by UV-vis diffuse reflectance spectra (DRS), XRD spectra, Scanning Electron Microscope (SEM) technology, and photovoltage measurement. The feasibility of improving the photocatalytic activity of TiO₂ film by combining the modification of Cu nanoparticles with the application of anodic bias was investigated. The experimental results showed that the deposited Cu has an apparent enhancement effect with respect to suppressing the recombination between the photogenerated charge carriers and enhancing the photocatalytic oxidation of formic acid. The combination could …

Investigation Of Adsorption And Oxidation Behavior Of Isosafrole On A Smooth Pt, Xiao-Hong Zhang, Xiao-Jing Su, Qi-Ling Zhong, Lei Zhang, De-Sheng Mei, Bin Ren, Zhong-Qun Tian

Journal of Electrochemistry

The electro-oxidation of isosafrole on a smooth platinum electrode was investigated in the non-aqueous solution. The CV curve shows two oxidation peaks and one reduction peak in the potential region between -0.5 V and 1.95 V. The relation between the oxidation and reduction peaks has been determined also by CV. The adsorption behavior of isosafrole on Pt was also investigated.

Electrochemical Lithium Insertion Of Nanosized Tio2, Ying Lan, Jian-Wen Liu, Xue-Ping Gao, Xing-Di Zhou, Jin-Qiu Qu, Feng Wu, De-Ying Song

Journal of Electrochemistry

The protonic titanate nanotubes with the diameter of 10～15 nm were synthesized via hydrothermal method in NaOH solution and the calcined nanotubes at 500 ℃ were transferred to anatase nanorods with the diameter of 12～20 nm due to dehydration.The electrochemical behavior of the anatase nanorods as lithium insertion materials was examined. The results showed that the nanorod electrode had the high initial discharge capacity of 232 mAh/g and second reversible capacity of 198 mAh/g. The capacity of nanorod electrode maintained 152mAh/g after 20 cycles.

Electrocatalytic And Lifetime Studies Of Commercial Catalystsin A Pemfc, Cheng Xuan, Yan-Yun Ma, Li Qi, Cheng Peng, Ling Chen, Jun Zhao, Ying Zhang, Qin-Bai Fan

Journal of Electrochemistry

A particularly designed H-type cell was used to simulate the operating condition of a hydrogen-air proton exchange membrane fuel cell (PEMFC). The electrocatalytic activity, morphology, structure and lifetime of commercially available catalysts, carbon support platinum (Pt/C) and unsupported platinum-ruthenium (Pt-Ru), were preliminary studied by carrying out electrochemical measurements and by SEM, XRD techniques. The catalysts were simultaneously tested in the H-cell under operation, and also separately tested in a conventional electrochemical cell for comparison. It was found that the characteristic peaks of hydrogen adsorption/desorption on cyclic voltammograms shifted considerably to a more positive direction for Pt/C, while a more negative …

Direct Electron Transfer Of Redox Proteins And Enzymes Promoted By Carbon Nanotube, Chen-Xin Cai, Jing Chen

Journal of Electrochemistry

The redox proteins (enzymes), such as hemoglobin (Hb), horseradish peroxidase (HRP) and glucose oxidase (GOx) were immobilized on the surface of the carbon nanotube modified with glassy carbon (CNT/GC) electrode, respectively. The experimental results showed that the redox proteins (enzymes) underwent effective and stable direct electron transfer reaction at the surface of CNT/GC electrode with a pair of nearly symmetrical redox peaks in phosphate buffer solution. The formal redox potential, E^0' , is almost independent on the scan rates, the average value of E^0'  for Hb, HRP and GOx is -0.343±0.001, -0.319±0.002 and -0.456±0.001 V (vs.SCE,pH 6.9), respectively. …

Stability And Electrochemical Performance Of Nio Cathode Modified By Zno Additive For Mcfc In Molten Carbonates, Bo Huang, Fei Li, Qing-Chun Yu, Gang Chen, Ke-Ao Hu

Journal of Electrochemistry

The ZnO/Ni composite cathode was fabricated by tape-casting method, which microstructures and phases were studied. The electrochemical behaviors of ZnO impregnated NiO cathodes were also evaluated in molten 62 mol%Li₂CO₃ + 38 mol%K₂CO₃eutectic at 650 ℃ by electrochemical impedance spectroscopy (EIS) as a function of ZnO content and immersion time. The ZnO impregnated nickel cathodes showed the similar porosity, pore size and morphology to the reference nickel cathode. The stability tests of ZnO impregnated NiO cathodes showed that the ZnO additive could dramatically reduce the solubility of NiO in a eutectic carbonate mixture …

Study On Reduction Process Of Electrolyic Manganese Dioxide In Situ By Ultraviolet-Visible Absorption Spectroscopy, Li-Cai Zhu, Zhong-Zhi Yuan, Wei-Shan Li

Journal of Electrochemistry

The concentrationsof soluble Mn(Ⅲ) species, during the reduction ofelectrolytic MnO₂ (EMD) in alkaline solution,have been monitored in situ by UV-visible spectroscopy. The concentration of Mn(Ⅲ) ion in solution changes with discharge time. The first electron discharge process of EMD can be described by three different steps: 1) the reduction of Mn⁴⁺ ions on the surface of EMD particles and the structural defect regions within the EMD, 2) the reduction of Mn⁴⁺ ions in ramsdellite, 3)the reduction of Mn⁴⁺ ions in pyrolusite. During the second electron discharge of EMD, the soluble Mn(Ⅲ) is reduced to Mn(Ⅱ) , …