Power and Energy Commons^™

Design And Implementation Of An X-Band Passive Rfid Tag, Praharshin Melaka Senadeera

Dissertations

This research presents a novel fully integrated energy harvester, matching network, multi-stage RF-DC rectifier, mode selector, RC oscillator, LC oscillator, and X-band power amplifier implemented in IBM 0.18-µm RF CMOS technology. We investigated different matching schemes, antennas, and rectifiers with focus on the interaction between building blocks. Currently the power amplifier gives the maximum output power of 5.23 dBm at 9.1GHz. The entire RFID tag circuit was designed to operate in low power consumption. Voltage sensor circuit which generates the enable signal was designed to operate in very low current. All the test blocks of the RFID tag were tested. …

Intelligent Approaches For Modeling And Optimizing Hvac Systems, Iii Raymond Tesiero

Dissertations

Advanced energy management control systems (EMCS), or building automation systems (BAS), offer an excellent means of reducing energy consumption in heating, ventilating, and air conditioning (HVAC) systems while maintaining and improving indoor environmental conditions. This can be achieved through the use of computational intelligence and optimization. This research will evaluate model-based optimization processes (OP) for HVAC systems utilizing MATLAB, genetic algorithms and self-learning or self-tuning models (STM), which minimizes the error between measured and predicted performance data. The OP can be integrated into the EMCS to perform several intelligent functions achieving optimal system performance. The development of several self-learning HVAC …

A Platinum Nanowire Network As A Highly Effective Current Collector For Intermediate Temperature Solid Oxide Fuel Cells, Hanping Ding, Xingjian Xue

Faculty Publications

We report the fabrication and evaluation of a platinum nanowire network as a highly efficient current collector for solid oxide fuel cells (SOFCs). The ink of carbon-black supported platinum nanoparticles was sprayed onto the cathode. After firing, the carbon black was oxidized and disappeared as carbon dioxide gas while the platinum nanoparticles connect with one another, forming a tree-branch-like nanowire network. The diameters of the nanowires range from 100 nm to 400 nm. Compared to a conventional platinum paste current collector, the polarization resistance of the PrBaCo₂O_5+δ (PBCO) cathode with a nanowire current collector was reduced …

Modeling Of Chemical-Mechanical Couplings In Anode-Supported Solid Oxide Fuel Cells And Reliability Analysis, Xinfang Jin, Xingjian Xue

Faculty Publications

Oxygen ionic transport in conducting ceramics is an important mechanism enabling solid oxide fuel cell (SOFC) technology. The multi-physicochemical processes lead to the fact that the distribution of oxygen vacancy site fraction is not uniform in a positive-electrode electrolyte negative-electrode (PEN) assembly. Different oxygen vacancy concentrations induce different volumetric expansion of ceramics, resulting in complicated chemical–mechanical coupling phenomena and chemical stress in SOFCs. In this research, a mathematical model is developed to study oxygen ionic transport induced chemical stress in an SOFC. The model is validated using experimental polarization curves. Comprehensive simulations are performed to investigate chemical stress distribution in …

Energy Optimization Of A Free-Piston Enhanced Hybrid Vehicle, Kenneth Jarod Jones

Dissertations

The world’s heavy dependence on vehicles which utilize hydrocarbon fuels as a primary power source has renewed the interest in electric and hybrid vehicles for industrial, commercial, and public use. The primary objective of this movement is centered on increased efficiency in energy usage for transportation. Hybrid vehicles which utilize an internal combustion engine as a linear generator, converting energy stored in hydrocarbon fuels into electrical power, could serve as a transitioning technology. The free-piston enhanced hybrid vehicle (FPHV) could potentially fill this role. The present work contains a theoretical and numerical approach to analyzing and optimizing the usage of …

Bermudagrass Growth In Soil Contaminated With Hydraulic Fracturing Drilling Fluid, Douglas Wolf, Kristofor R. Brye

Discovery, The Student Journal of Dale Bumpers College of Agricultural, Food and Life Sciences

Hydraulic fracturing is the process of injecting aqueous solutions at high pressure to break apart rock formations and increase the extraction of natural gas. The solutions are recovered and have been land-applied as one disposal technique. Excessive fluid application can result in increased soil salinity that can inhibit plant growth. The objective of this greenhouse study was to evaluate the effects of inorganic fertilizer, broiler litter, and Milorganite® and soil depth interval (0-15 cm or 0-30 cm) on the growth of bermudagrass [Cynodon dactylon (L.) Pers] in soil that was collected from a site that had been contaminated with fracturing …

Dilute-Acid-Extractable Phosphorus, Arsenic, And Selenium In Weathered And Fresh Coal Fly Ash, Chris Wilbanks, Kristofor Brye, David Miller

Discovery, The Student Journal of Dale Bumpers College of Agricultural, Food and Life Sciences

Fly ash is a byproduct of the combustion of coal, primarily by coal-fired power plants. Over 97.8 million tonnes of fly ash are produced each year in the United States. Fly ash can contain trace elements in concentrations that can cause health risks. Recent spills have highlighted that fly ash disposal is problematic. The objective of this study was to evaluate the effects of fly-ash type (fresh and weathered) from a local coal-burning power plant and extraction time (2 and 6 h) on dilute-acid extractable concentrations of phosphorus (P), arsenic (As), and selenium (Se). Ash samples were extracted with 0.1 …

Out-Of-Step Detection Based On Zubov’S Approximation Boundary Method, Yawei Wei

Dissertations, Master's Theses and Master's Reports - Open

Disturbances in power systems may lead to electromagnetic transient oscillations due to mismatch of mechanical input power and electrical output power. Out-of-step conditions in power system are common after the disturbances where the continuous oscillations do not damp out and the system becomes unstable. Existing out-of-step detection methods are system specific as extensive off-line studies are required for setting of relays. Most of the existing algorithms also require network reduction techniques to apply in multi-machine power systems. To overcome these issues, this research applies Phasor Measurement Unit (PMU) data and Zubov’s approximation stability boundary method, which is a modification of …

Fault Location Algorithms, Observability And Optimality For Power Distribution Systems, Wanjing Xiu

Theses and Dissertations--Electrical and Computer Engineering

Power outages usually lead to customer complaints and revenue losses. Consequently, fast and accurate fault location on electric lines is needed so that repair work can be carried out as fast as possible.

Chapter 2 describes novel fault location algorithms for radial and non-radial ungrounded power distribution systems. For both types of systems, fault location approaches using line to neutral or line to line measurements are presented. It’s assumed that network structure and parameters are known, so that during-fault bus impedance matrix of the system can be derived. Functions of bus impedance matrix and available measurements at substation are formulated, …

Prediction Model To Estimate The Zero Crossing Point For Faulted Waveforms, Md. Shakawat Hossan

Theses and Dissertations--Electrical and Computer Engineering

In any power system, fault means abnormal flow of current. Insulation breakdown is the cause of fault generation. Different factors can cause the breakdown: Wires drifting together in the wind, Lightning ionizing air, wires with contacts of animals and plants, Salt spray or pollution on insulators. The common type of faults on a three phase system are single line-to-ground (SLG), Line-to-line faults (LL), double line-to-ground (DLG) faults, and balanced three phase faults. And these faults can be symmetrical (balanced) or Unsymmetrical (imbalanced).In this Study, a technique to predict the zero crossing point has been discussed and simulated. Zero crossing point …

Testing Of Two Novel Semi-Implicit Particle-In-Cell Techniques, Trenton J. Godar

Browse all Theses and Dissertations

PIC (Particle-in-cell) modeling is a computational technique which functions by advancing computer particles through a spatial grid consisting of cells, on which can be placed electric and magnetic fields. This method has proven useful for simulating a wide range of plasmas and excels at yielding accurate and detailed results such as particle number densities, particle energies, particle currents, and electric potentials. However, the detailed results of a PIC simulation come at a substantial cost of computational requirement and the algorithm can be susceptible to numerical instabilities. As processors become faster and contain more cores, the computational expense of PIC simulations …

Modeling And Validation Of A Synchronous-Machine/Controlled-Rectifier System, Kyle A. Hord

Theses and Dissertations--Electrical and Computer Engineering

The hardware validation of a novel average-value model (AVM) for the simulation of a synchronous-generator/controlled rectifier system is presented herein. The generator is characterized using genetic algorithm techniques to fit standstill frequency response (SSFR) measurements to q and d-axis equivalent circuits representing the generator in the rotor reference frame. The generator parameters form the basis of a detailed model of the system, from which algebraic functions defining the parametric AVM are derived. The average-value model is compared to the physical system for a variety of loading and operating conditions including step load change, change in delay angle, and external closed-loop …

Investigation Of Protection Issues And Method For The Distribution System With Distributed Generations, Ke Xu

Theses and Dissertations--Electrical and Computer Engineering

Because DGs are introduced into distribution systems, the coordination of fuses and reclosers doesn’t work well. It means the original protection schemes are not available for the distribution systems with DGs. This thesis paper presents the study on the impacts of DGs on the fault current and voltage in the distribution system by the simulation of a model distribution system. After we study the impacts of DG on distribution systems, there is an introduction of current several current protection schemes and fault locations methods. At last, an adaptive protection scheme with a more efficient fault location method for the distribution …

Multifrequency Averaging In Power Electronic Systems, Fei Pan

Theses and Dissertations--Electrical and Computer Engineering

Power electronic systems have been widely used in the electrical power processing for applications with power levels ranging from less than one watt in battery-operated portable devices to more than megawatts in the converters, inverters and rectifiers of the utility power systems. These systems typically involve the passive elements such as inductors, capacitors, and resistors, the switching electronic components such as IGBTs, MOSFETS, and diodes, and other electronic circuits. Multifrequency averaging is one of the widely used modeling and simulation techniques today for the analysis and design of power electronic systems. This technique is capable of providing the average behavior …

A New Design Of Dc-Dc Converter For Capacitive Deionization Process, Zhiao Li

Theses and Dissertations--Electrical and Computer Engineering

The shortage of clean water has become a significant global problem, and capacitive deionization (CDI) is a technology that can be used to help relieve the problem. A Ćuk converter system that can recover energy from CDI cells is described. This converter transfers energy between two CDI cells when a cell is in its desorption period, allowing energy that would otherwise be lost to be recovered and improving overall system efficiency. In order to control the states of the MOSFET switches in the converter, a self boost charge pump is used. In this way, the microcontroller can control system duty …

Coordinated Voltage And Reactive Power Control Of Power Distribution Systems With Distributed Generation, Esa A. Paaso

Theses and Dissertations--Electrical and Computer Engineering

Distribution system voltage and VAR control (VVC) is a technique that combines conservation voltage reduction and reactive power compensation to operate a distribution system at its optimal conditions. Coordinated VVC can provide major economic benefits for distribution utilities. Incorporating distributed generation (DG) to VVC can improve the system efficiency and reliability. The first part of this dissertation introduces a direct optimization formulation for VVC with DG. The control is formulated as a mixed integer non-linear programming (MINLP) problem. The formulation is based on a three-phase power flow with accurate component models. The VVC problem is solved with a state of …

Hydrothermal Processing Of Biomass For Biofuels, Sandeep Kumar

Civil & Environmental Engineering Faculty Publications

[First paragraph] In recent years, significant research interests have been placed on the conversion of non-food biomass resources such as lignocellulosic biomass (terrestrial) and algae (aquatic) to biofuels. Among all the alternative or renewable energy options, biomass is the only resource which is carbon neutral and can potentially replace part of fossil fuels use as liquid transportation fuels as well as contribute to electricity generation. Therefore, it can play a significant role in partially replacing oil, natural gas, and coal utilization for heat and energy generation. However, high moisture content of fresh biomass or algae is one of the major …

Analysis Of Onshore Wind - Solar Pv - Battery Bank Power Generation System Development For Toamasina Port, Hary Lys Jean Louis Soloniainanirinanandrianina

World Maritime University Dissertations

No abstract provided.

Cost And Benefit Analysis Of Shore Side Electricity In The Port Of Tanjung Perak, Indonesia, Oscar Yogi Yustiano

World Maritime University Dissertations

No abstract provided.

Application Of Synchrotron Radiation Based Electrochemical In-Situ Techniques To Study Of Electrode Materials For Lithium-Ion Batteries, Zheng-Liang Gong, Wei Zhang, Dong-Ping Lv, Xiao-Gang Hao, Wen Wen, Zheng Jiang, Yong Yang

Journal of Electrochemistry

Due to its merits of high brightness and high intensity, high level of polarization and wide tunability in energy, etc., synchrotron radiation technique provides an unique platform for analysis of the relationship among composition–structure–performance of materials for lithium ion batteries, especially for in-situ, real time dynamic investigation of the electrochemical reaction mechanism, aging process and failure mechanism during charge-discharge cycling. In this paper, we review the latest developments in application of synchrotron based electrochemical in-situ experimental methods to studies of lithium ion batteries. The paper mainly focuses on the application of electrochemical in-siu XRD and XAFS techniques to the investigations …

Controllable Synthesis Of Dispersed Spherical Fe3O4 Nanoparticles As Lithium-Inserted Materials, Hong-Li Zou, Wei-Shan Li

Journal of Electrochemistry

Dispersed spherical Fe₃O₄ nanoparticles were synthesized by a hydrothermal method. The influences of odecyl trimethyl ammonium bromide (DTAB) concentration on the morphology and particle size of the as-prepared Fe₃O₄ were studied. Electrochemical performance of the as-prepared sample as anode materials of lithium ion battery was investigated. It is found that the as-prepared sample exhibits superior rate performance and cycle performance. The nano-sized materials provide structural stability and favor the transfer of lithium ions.

An Investigation On The Solid Electrolyte Interphase Of Silicon Anode For Li-Ion Batteries Through Force Curve Method, Jie-Yun Zheng, Hao Zheng, Rui Wang, Hong Li, Li-Quan Chen

Journal of Electrochemistry

Non-aqueous electrolyte has been widely used in commercial Li-ion batteries. Optimized choices are proceeding among the various types of salts and solvents in an effort to achieve higher performance of electrolyte. However, the electrolyte will be reduced in low potential and the reductive product will be deposited on the surface of anode to form a passivating layer, solid electrolyte interphase (SEI). Herein an atomic force microscopy (AFM) based method was introduced to study the structure and mechanical property of SEI on silicon thin film anode during the first cycle. Silicon has been known as the most potential candidate anode for …

Preparation And Electrochemical Properties Of Flake-Like Liv3O8 By Soft Template Assisted Sol-Gel Method As Anode Material For Aqueous Li-Ion Battery, Shuai Tan, Dan Sun, Hai-Yan Wang, Tian-Li Hou, Zhong-Xing Xiao, You-Gen Tang

Journal of Electrochemistry

Composite electrode of CuF₂/MoO₃/C was fabricated through high energy mechanical milling. The properties of CuF₂/MoO₃/C were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), high resolution transmission electron microscopy (TEM), galvanostatic charge-discharge measurements, cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). The results showed that the grain sizes of CuF₂ and MoO₃ after milling were 200 ~ 300 nm, and the initial discharge capacity of CuF₂/MoO₃/C was 647 mAh·g^-1 at room temperature and at a current density of 10 mAh·g^-1. However, the …

Synthesis And Electrochemical Performance Of Nano Licopo4 By Polyol Method, Fei Wang, Yang Jun

Journal of Electrochemistry

High potential LiCoPO₄ cathode material was synthesized by polyol method. Carbon layer of ca. 3 nm thick was coated on the LiCoPO₄ surfaces by chemical vapor deposition from methylbenzene. Crystalline structure, morphology and electrochemical performance of the sample were studied by XRD, SEM, TEM, CV and galvanostatic charge/discharge curve. The synthesized material via polyol method showed a pure phase of LiCoPO₄. The LiCoPO₄/C electrode delivered a high discharge capacity of 132 mAh·g^-1 and maintained 78% of the initial capacity after 50 cycles at 0.1C rate. The two-step extraction/insertion behavior of Li⁺ in …

Aqueous Solution-Evaporation Route Synthesis And Phase Structural Research Of The Li-Rich Cathode Li1.23Ni0.09Co0.12Mn0.56O2 By In-Situ Xrd, Chong-Heng Shen, Shou-Yu Shen, Zhou Lin, Xiao-Mei Zheng, Hang Su, Ling Huang, Jun-Tao Li, Shi-Gang Sun

Journal of Electrochemistry

The Li-rich Li_1.23Ni_0.09Co_0.12Mn_0.56O₂ material was synthesized via aqueous solution-evaporation route. The structure and morphology of the material were characterized by means of XRD and SEM. The results indicated that the single particle of the product was polygonal with the size of 330 nm and the structure was layered solid solution with a certain amount of Li₂MnO₃. Electrochemical tests showed that the first discharge capacity of the Li-rich layered material was 250.8 mAh·g^-1 at 0.1C, the capacity retention was 86.5% after 40 cycles. Through in-situ XRD study …

Cmk-3/Sulfur Composite (CXSY) And Room-Temperature Na/S Battery, Qing Zhao, Yu-Xiang Hu, Kai Zhang, Li-Jiang Wang, Zhan-Liang Tao, Jun Chen

Journal of Electrochemistry

A series of ordered mesoporous carbon (CMK-3)/sulfur composite (C_xS_y) with different sulfur contents were synthesized via a melt-diffusion method. XRD, Raman, BET, SEM, and TEM techniques were used to characterize the structure and morphology of the as-prepared composite. The electrochemical performance of CMK-3/sulfur composite as the electrode of Na/S battery was tested at room temperature. Cyclic voltammograms show that one obvious reduction peak was located at about 1.61V, which is corresponding to the formation of Na₂S_x (x=2~5), while two oxidation peaks were displayed at about 1.82V and 1.95V, which are belonging to the …

Preparation Of The Particle Size Controllable Lifepo4/C And Its Electrochemical Profile Characterization, Ming-E Wang, Jing-Yuan Liu, Meng-Yan Hou, Yong-Yao Xia

Journal of Electrochemistry

We adopted an effective route to prepare the particle size controllable core-shell structure carbon-coated LiFePO₄ from different sized FePO₄ precursors, varying from 80 nm, 200 nm and 1 μm by an in situ polymerization method integrated with a surface modification technology. The discharge capacities of the three sized LiFePO₄/C are, respectively, 162 mAh·g^-1, 142 mAh·g^-1 and 92 mAh·g^-1 at 0.1C rate. The nano-sized LiFePO₄-a/C (80 nm) delivers a discharge capacity as large as 100 mAh·g^-1 even at 30C, while the macroscopic LiFePO₄-c/C (1 μm) exhibits a much …

Preparation And Electrochemical Properties Of Amorphous Znsno3/C By Hydrothermally Carbonization Method, Guo-Qing Fang, Rui-Xue Zhang, Wei-Wei Liu, Bing-Bo Xia, Hong-Dan Sun, Hai-Bo Wang, Jing-Jing Wu, Shinko Kaneko, De-Cheng Li

Journal of Electrochemistry

The amorphous ZnSnO₃@C composite was synthesized via a simple glucose hydrothermal and subsequent carbonization approach. The structure, morphology and electrochemical property of the composite were characterized by XRD, TEM and electrochemical measurements. Compared to bare ZnSnO₃, the ZnSnO₃/C composite exhibited markedly enhanced lithium storage property and cycle performance, delivering a reversible capacity of 659 mAh·g^-1 after 100 cycles at a current density of 100 mA·g^-1.

Synthesis And Electrochemical Property Of Li2Fesio4/C Cathode Material By Solid State Method, Jiao-Li Sun, Zhi-Jiao Chen, Yi-Xiao Li, Hu Cheng

Journal of Electrochemistry

Li₂FeSiO₄/C cathode material was synthesized using Li₂SiO₃ and FeC₂O₄ as raw materials by solid state method. The structure and morphology of the material were characterized by XRD and SEM. The electrochemical properties of the material were studied by constant-current cyclic testing. The results show that Li₂FeSiO₄/C has a good electrochemical performance. The first discharge capacity of Li₂FeSiO₄/C cathode material at 30oC reached 167 mAh∙g^-1 when cycled at 10 mA∙g^-1 between 1.5 and 4.8 V.

Electrochemical Na-Storage Materials And Their Applications For Na-Ion Batteries, Jiang-Feng Qian, Xue-Ping Gao, Han-Xi Yang

Journal of Electrochemistry

Oncoming large scale electric energy storage (EES) requires battery systems not only to have sufficient storage capacity but also to be cost-effective and environmentally friendly. Li-ion batteries for widespread EES applications may be limited due to the constraint of global lithium resource. From the considerations of available resources and environmental impact, Na-ion batteries have potential advantages as next generation secondary batteries and an alternative to Li-ion batteries. However, in the present state of the art, the Na-storage cathodes reported so far are still deficient both in energy density and power capability, while the carbon and alloy anodes for Na-ion batteries …