Power and Energy Commons^™

Effects Of Carbon Interlayer On Electrochemical Performance Of Lithium-Sulfur Cell, Jin-Peng Yu, Ming Zhang, Fei Ding, Zhi-Yuan Tang, Xing-Jiang Liu

Journal of Electrochemistry

Three kinds of conductive carbon films were prepared with Super-P (SP), KB and MWCNTs, and then the as-prepared carbon films were applied as an interlayer between a sulfur electrode and a separator for constructing a coin-type lithium-sulfur (Li-S) cell, respectively. The assessment results show that all the cells delivered the reversible capacities higher than 800 mAh·g^-1 after 40 cycles when the sulfur loading was up to 80% (by mass) in the sulfur electrode. Due to significant differences of physical properties among the carbon materials, the cell with a KB interlayer exhibited higher electrochemical polarization; the cycling performance of the …

Preparation Of Pt/H-Tio2 Catalyst With Improved Catalytic Performance For Methanol Electrooxidation, Jin Han, Zhi-You Zhou, Qiang Wang, Miao-Qiang Lv, Chi Chen, Shi-Gang Sun

Journal of Electrochemistry

White TiO₂ nanorods were synthesized by hydrothermal method with TiCl₄ as a precursor. As-synthesized TiO₂ nanorods were further subjected to high-temperature (550 ^oC) heat treatment for 2 h under H₂ atmosphere to prepare gray black hydrogen-treated TiO₂ (H-TiO₂) nanorods with oxygen vacancies and Ti³⁺ interstitial atoms. The Pt nanoparticles of 1.9 nm were supported on these two types of TiO₂ nanorods to form Pt/TiO₂ and Pt/H-TiO₂ catalysts. XRD data indicates that the crystal structure of TiO₂ was still reserved as rutile after hydrogen treatment, but the surface …

Effect Of Al-Doping In Li-Rich Material Li1.2Mn0.543Co0.078Ni0.155Al0.030O2 For Lithium-Ion Batteries, Xiao-Xi Jin, Yi-Xiao Li, Yong Yang, Zhou-Cheng Wang

Journal of Electrochemistry

The Al-doped 0.5Li₂MnO₃·0.5Li(Mn_0.4Co_0.2Ni_0.4)O₂ compounds were successfully synthesized as cathode materials for lithium-ion batteries. The pristine and Al-doped materials were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD), inductively coupled plasma-atomic emission spectrometry (ICP-AES) and laser Raman spectroscopy. The results indicated that all the prepared materials were indexed as a hexagonal structure with R-3m space group, and Al element had been introduced into lattice. When cycled at 180 mA·g^-1 (1 C-rate), the capacity retention of 4% (by mole) Al-doped 0.5Li₂MnO₃·0.5Li(Mn_0.4Co_0.2Ni …

Application Of Ionic Liquid Pp14Tfsi In Electrolyte Systems For Rechargeable Mg Batteries, Jin-Jie Zhu, Fei-Fei Wang, Yong-Sheng Guo, Jun Yang, Yan-Na Nuli, Jiu-Lin Wang

Journal of Electrochemistry

A phenolated-based Mg salt was prepared. The mixture of THF and N-methyl-N-butyl-piperidinium bis(trifluoromethanesulfonyl)imide (PP14TFSI) serves as the mixed solvent instead of pure THF for rechargeable Mg batteries systems. This new type of electrolyte system not only has optimal reversibility of Mg, but also owns a wide electrochemical window (2.7 V vs. Mg) and high ionic conductivity (7.77 mS·cm^-1). More importantly, the addition of Ionic Liquid suppresses the volatility of THF and improves the safety of rechargeable Mg batteries. The result shows that the mixture of THF and piperidyl-based Ionic Liquid could be regarded as a good solvent candidate …

Electrocatalytic Oxidation Of Glycerol At The Platinum Electrode Modified With An Nd-Fe-Moo42- Cyano-Bridged Mixed Coordination Polymer, Yong-Jun Ma, Yu-Xiu Tian, Jing Liu, Min Zhou, Jing Ding, Zhi-Mei Jin, Xiang-Mei Wang

Journal of Electrochemistry

A platinum electrode decorated with the ordered Nd-Fe-MoO₄^2- cyano-bridged mixed coordination polymer was successfully prepared by electrodeposition in virtue of the lyotropic liquid crystal soft template methods, and electrocatalytic oxidation behavior of glycerol was investigated on the chemically modified electrode by cyclic voltammetry. The influences of experimental factors such as the concentrations of H⁺ and SO₄^2- in electrolytes, glycerol concentration and scan rate on the electrocatalytic activity of glycerol at the modified electrode were also studied. It indicated that the proper amount of SO₄^2- in weakly acidic electrolyte could help to improve the …

Effect Of Temperature On The Self-Humidifying Open-Cathode Proton Exchange Membrane Fuel Cell, Si-Chen Zhao, Ben Wang, Qiu-Hong Jia, Ming Han, Yu-Hong Xie

Journal of Electrochemistry

Based on the experiments about the output characteristics of a home-made temperature-controlled PEMFC system with atmospheric pressure and no external humidifying condition in different loading voltages and operating temperatures, the optimum operating temperature at different loading voltages can be obtained by tracking the output characteristics of PEMFC operating over a range of temperatures. By analyzing the fitted data the kinetic parameters are evaluated and the effect of different operating temperatures on the PEMFC performance is discussed from a view of electrode kinetics.

An Equivalent Circuit Model For Redox Flow Battery Stack, Dong-Jiang You, Hua-Min Zhang

Journal of Electrochemistry

This paper introduces an equivalent circuit model for a redox flow battery stack. The model combines the electrochemical reaction of the battery cell and the shunt current of the battery stack. An all-vanadium redox flow battery stack of 1kW rated output power is tested through transient response and self-discharge experiments. All the parameters used for the modeling are obtained. Calculated shunt current and distribution of calculated battery voltage are shown in the results. It is concluded that the impedance of the battery stack can be obtained by the experimental results of the transient response and self-discharge measurements. The capacity lose …

Thermo-Electric Generator Evaluation Board, Jeanette Brooks, Cody Sullivan, Adrian Rothenbuhler

College of Engineering Presentations

Thermoelectric generators (TEGs) are solid-state devices that convert temperature gradients into electrical energy. TEGs are desirable sources of energy as they require low maintenance and have high reliability with potential for use in low power and remote applications. To date, no simple and affordable, common test platform for evaluating the performance of TEGs in their associated environment exists. This project is aimed at providing such a platform to deliver performance data that is crucial in power budgeting and viability studies of TEG-powered applications. The design utilizes the common LTC3109 converter chip and an off-the-shelf micro-controller for temperature and load current …

An Adaptive Kalman Filter For Voltage Sag Detection In Power Systems, Hisham Odeh Alrawashdeh

Dissertations

The exact values of the noise covariance matrix of the Kalman filter state vector Q and the measured signal noise covariance matrix R must be obtained in order to achieve the optimal performance of the Kalman filter. There have been many techniques and assumptions made to evaluate and compute Q and R. The effects of Q and R are investigated in detail in this dissertation. Based on these investigations, the Kalman filter has been modeled to detect the fundamental signal amplitude variations of power system signals. This technique helps in evaluating voltage sags in power systems.

Two algorithms are …

Position/Speed Sensorless Control For Permanent-Magnet Synchronous Machines, Yue Zhao

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

Permanent-magnet synchronous machines (PMSMs) are widely used in industrial applications owing to their distinctive advantages, such as high efficiency, high power density, and wide constant power region. To achieve high-performance field oriented control, accurate rotor position information, which is usually measured by rotary encoders or resolvers, is indispensable. However, the use of these sensors increases the cost, size, weight, and wiring complexity and reduces the mechanical robustness and the reliability of the overall PMSM drive systems. The goal of the research for this dissertation was to develop a rotor position/speed sensorless control system with performance comparable to the sensor-based control …

Generation Of Bipolar Nanosecond Pulses, Sambasiva Rao Rajulapati

Electrical & Computer Engineering Theses & Dissertations

Bipolar pulse generation has been studied using transmission line technology, which was mainly used for monopolar pulse generation. In this thesis, low impedance, high current, nanosecond pulse generators were designed, constructed and tested. Five transmission lines were connected in parallel, so the impedance was 10 n. The transmission lines were switched by a spark gap switch operated in air. The closing of the switch creates a matched condition on one side of the transmission lines and a short circuit on the other side of the transmission lines. When the transmission lines are precharged, one of the two waves in opposite …

Co2 Recycling Using Microalgae For The Production Of Fuels, Michael H. Wilson, John Groppo, Andrew Placido, S. Graham, S. A. Morton Iii, Eduardo Santillan-Jimenez, Aubrey Shea, Mark Crocker, Czarena Crofcheck, Rodney Andrews

Center for Applied Energy Research Faculty and Staff Publications

CO₂ capture and recycle using microalgae was demonstrated at a coal-fired power plant (Duke Energy’s East Bend Station, Kentucky). Using an in-house designed closed loop, vertical tube photobioreactor, Scenedesmus acutus was cultured using flue gas as the CO₂ source. Algae productivity of 39 g/(m² day) in June–July was achieved at significant scale (18,000 L), while average daily productivity slightly in excess of 10 g/(m² day) was demonstrated in the month of December. A protocol for low-cost algae harvesting and dewatering was developed, and the conversion of algal lipids—extracted from the harvested biomass—to diesel-range hydrocarbons via catalytic …

The Design, Implementation, Assessment, And Evaluation Of A Power Systems Protection Laboratory Curriculum, Jennifer Ferris

Dissertations and Theses

Over the last the last three decades, there has been a significant and documented decrease of power engineering curriculum within U.S. electrical engineering programs. Development of lifelong learners capable of critical and independent thinking is required to replace the large number of upcoming retirees from the industry and to prepare for the engineering challenges new technologies, laws and regulations are bringing to the electrical power system. In response to these challenges, Portland State University redesigned its BSEE and MSECE power engineering programs in order to create a launching pad for successful power engineering careers. A course series on power system …

Influence Of Reduction Promoters On Stability Of Cobalt/Γ-Alumina Fischer-Tropsch Synthesis Catalysts, Gary Jacobs, Wenping Ma, Burtron H. Davis

Center for Applied Energy Research Faculty and Staff Publications

This focused review article underscores how metal reduction promoters can impact deactivation phenomena associated with cobalt Fischer-Tropsch synthesis catalysts. Promoters can exacerbate sintering if the additional cobalt metal clusters, formed as a result of the promoting effect, are in close proximity at the nanoscale to other cobalt particles on the surface. Recent efforts have shown that when promoters are used to facilitate the reduction of small crystallites with the aim of increasing surface Co⁰ site densities (e.g., in research catalysts), ultra-small crystallites (e.g., < 2–4.4 nm) formed are more susceptible to oxidation at high conversion relative to larger ones. The choice of promoter is important, as certain metals (e.g., Au) that promote cobalt oxide reduction can separate from cobalt during oxidation-reduction (regeneration) cycles. Finally, some elements have been identified to promote reduction but either poison the surface of Co⁰ (e.g., Cu), or produce excessive light gas selectivity (e.g., Cu and Pd, or Au at …

Boosty-Bit: Power For Pint-Sized Projects, Timothy Grijalva

Electrical Engineering

In order to make it easier for hobbyists to create small portable microcontroller based electronics projects, I have created Boosty-bit, a tiny DC-DC boost convert that runs off a single alkaline battery cell (AA or AAA). The Boosty-bit converter can source up to 250mA @ 3.3v, making it ideal for many microcontroller based projects. In addition to power management, Boosty-bit is also physically small, allowing it to fit inside pen/marker-sized enclosures along with a AAA battery and a microcontroller. Boosty-bit aims to be the ideal solution for “makers” who desire portability and compact form factors in their projects.

Electrochemical Performance Of Si-C Composites Prepared By Discharge-Plasma Assisted Milling, Yu-Long Chen, Ren-Zong Hu, Hui Liu, Wei Sun, Min Zhu

Journal of Electrochemistry

Silicon-carbon (Si-C) composites, with microstructure of multi-scaled Si particles being homogenously dispersed in micro-sized carbon matrix, had been prepared by dielectric barrier discharge plasma assisted two-step milling for the first time. The Si-C composite anode had a discharge capacity of 1259 mAh·g^-1 at the first cycle, while the capacity retained 474 and 396 mAh·g^-1 after 20 and 100 cycles, respectively. Charge-discharge curves and AC impedance response indicated that both silicon and carbon phases in the composite anode were involved during the lithiation/delithiation reactions and the electron transport resistance in the Si-C composite anode was much lower than that …

Preparation Of High Performance Porous Silicon Powders By Etching Al-Si Alloy In Acid Solution For Lithium Ion Battery, Shi-Ji Hao, Chun-Li Li, Kai Zhu, Ping Zhang, Zhi-Yu Jiang

Journal of Electrochemistry

Porous silicon powders prepared by etching Al-Si alloy using an acid solution was reported in the first time. The morphology and structure of as-obtained material were investigated using scanning electron microscopy (SEM) and X-ray diffraction (XRD) method. It was found that the spongy porous silicon powders presented well crystalline structure and consisted of nano-Si particles. The particle size of porous Si powders was about 20 μm, and the specific surface area was 102.7 m²·g^-1. The electrochemical properties of porous silicon powders were evaluated as an anode material for lithium ion batteries. The material proportion in the …

Pulse Electrodeposition Of Pd-Ni Alloy Nanoparticles For Electrocatalytic Oxidation Of Formic Acid, Fang-Zu Yang, Jun-Pei Yue, Zhong-Qun Tian, Shao-Min Zhou

Journal of Electrochemistry

The Pd-Ni alloy nanoparticles with nickel atomic contents of 12.0%, 16.4% and 22.6% were successfully electrodeposited from a Pd-Ni alloy electrolyte by square wave pulse plating. The alloy nanoparticles were in the spherical shape with a diameter of 50 ~ 80 nm. As the growth potential of the alloy was negatively shifted, the nickel content of the alloy was increased, and the size of the nanoparticles was almost the same, whereas the number, the degree of crosslinking and the real active area of the nanoparticles were increased. As the nickel content of the alloy nanoparticles increased, the peak current for …

Synthesis And Electrochemical Properties Of Lico1-XMgXMno4 And Lico1-XAlXMno4 (X= 0, 0.02, 0.05, 0.1) As Positive Materials For Lithium-Ion Batteries, Mei-Ling You, Qing-Song Tong, Xiu-Hua Li, Min Lin, Xing-Kang Huang, Yong Yang

Journal of Electrochemistry

The Al-doped and Mg-doped LiCoMnO₄ materials were synthesized through solid-state reaction. The effects of doping amounts of Mg and Al on the initial capacities, discharge plateaus, and cycle performances were investigated. The morphologies and structures of the as-prepared materials were studied by scanning electron microscopy and powder X-ray diffraction. The results indicate that the as-prepared samples were composed of uniform, well-crystallized particles. The pristine LiCoMnO₄ possessed an initial capacity of 87.0 mAh·g^-1, while LiCo_0.98Mg_0.02MnO₄ and LiCo_0.98Al_0.02MnO₄ delivered 91.3 and 93.6 mAh·g^-1, respectively. The proper …

Fabrication And Impedance Performance Of Gradient Lani0.6Fe0.4O3-δ-Gd0.2Ce0.8O2 Composite Cathodes For Intermediate Temperature Solid Oxide Fuel Cell, Yang Li, Bo Huang, Meng Yuan, Zhi-Qiu Zhang, Zong-Yao Liu, Xu-Chen Tang, Xin-Jian Zhu

Journal of Electrochemistry

A LNF-GDC composite cathode with a gradual change in the composition between ScSZ electrolyte and LNF cathode was fabricated to reduce the cathode polarization resistance (R_p). The gradual change in composition between ScSZ electrolyte and LNF cathode shows the decreases in the charge transfer resistance (R_ct) and gas phase diffusion resistance (R_d). The results revealed that the Rp value, measuring 0.452 Ω·cm² at 750 °C, was the lowest for LNF-GDC composite cathodes with three layers and gradient changes in composition between ScSZ and LNF (Cathode C),, whereas the Rp value of 70%LNF-30%GDC composite …

Electrochemical Oxidation Of Ammonium Nitrite In Absorption Solution Of Flue Gas, Yong-Hong Lu, Xiao-Bo Dong, Li-Sha Wang, Yan Liu, Chen-Jian Zhu, Hai-Bo Xu

Journal of Electrochemistry

In order to make full uses of ammonium nitrite in absorption solution from flue gas simultaneous desulfurization, denitrification and demercurization processes, here the electrochemical oxidation method was used to transform ammonium nitrite into ammonium nitrate. By using polarization curve, cyclic voltammogram and galvanostatic methods, suitable electrode materials were evaluated and chosen. The influence of electrolyte composition was discussed and the appropriate process parameters were obtained. Finally, the effect of electrochemical oxidation was confirmed by chemical analysis method. In 0.05 mol·L^-1 NaNO₂ + 0.05 mol·L^-1 (NH₄)₂SO₄ simulated absorption solution (5 L, pH = …

Study On Carbon Supported Pd Catalysts Modified By Phosphomolybdic Acid For H2O2 Electrocatalytic Reduction, Li-Mei Sun, Cheng Zhang, Ying-Rong Bao, Hong-Xia Li

Journal of Electrochemistry

The Pd/C catalyst was prepared with the chemical reduction method, and phosphomolybdic acid (PMA) was modified on the Pd/C catalyst using the dipping method. The compositions and structures of the Pd/C and Pd/C modified by phosphomolybdic acid (PMA-Pd/C) catalysts were characterized with X-ray diffraction and Fourier Transform infrared spectroscopy analyses. The electrocatalytic activity and stability of the catalysts for the reduction of hydrogen peroxide (H₂O₂) were studied using cyclic voltammetry and chronoamperometry. The results showed that the phosphomolybdic acid was tightly fixed on the surface of Pd/C catalyst through the chemical interaction. The eletrocatalytic activity of …

Preparation Of Pd/Tio2/C Catalyst And Its Electrocatalytic Performance In Basic Solution For Ethanol Oxidation, Qiao-Xia Li, Yi-Chao Yang, Ming-Shuang Liu, Hong-Min Mao, Qun-Jie Xu

Journal of Electrochemistry

Nanoparticles TiO₂ were prepared by hydrothermal method using precursor tetrabutyl titanate. The Pd/TiO₂/C catalyst was synthesized by liquid phase reducing method supported on nano TiO₂ and Vulcan carbon XC-72. The Pd/TiO₂/C catalyst was characterized by XRD, TEM, cyclic voltammetry, and chronopotentiometry. XRD confirmed the face-centered cubic structure of Pd particles, and TEM indicated that Pd particles (size 3 ~ 4 nm) dispersed uniformly on TiO₂ and carbon XC-72. The results from cyclic voltammogram and chronopotentiogram showed the higher ethanol oxidation activity and stability of Pd/TiO₂/C catalyst (20% Pd) as compared with …

Design And Development Of A Novel Glucose Biosensor Based On The Ferrocene-Functionalized Fe3O4 Nanoparticles/Carbon Nanotubes/Chitosan Nanocomposite Film Modified Electrode, Hua-Ping Peng, Dai-Jun Zha, Wei Chen, Ai-Lin Liu, Xin-Hua Lin

Journal of Electrochemistry

A novel platform for the fabrication of glucose biosensor was successfully constructed by entrapping glucose oxidase (GOD) in a ferrocene monocarboxylic acid-aminated Fe₃O₄ magnetic nanoparticles conjugate (FMC-AFNPs)/chitosan (CS)/multiwall carbon nanotubes (MWNTs) nanocomposite. The formation of FMC-AFNPs could effectively prevent the leakage of ferrocene and retain its electrochemical activity. This GOD/FMC-AFNPs/CS/MWNTs matrix provided a biocompatible microenvironment for retaining the native activity of the immobilized GOD. Moreover, the presence of MWNTs enhanced the charge-transport properties of the composite and facilitated electron transfer between the GOD and the electrode for the electrocatalysis of glucose. Under the optimal conditions the designed …

Household Solar Power System, He Jiang

Dissertations, Master's Theses and Master's Reports - Open

Photovoltaic power has become one of the most popular research area in new energy field. In this report, the case of household solar power system is presented. Based on the Matlab environment, the simulation is built by using Simulink and SimPowerSystem. There are four parts in a household solar system, solar cell, MPPT system, battery and power consumer. Solar cell and MPPT system are been studied and analyzed individually. The system with MPPT generates 30% more energy than the system without MPPT. After simulating the household system, it is can be seen that the power which generated by the system …

Hvac System Analysis And Energy Audit: The Providence Athenaeum, Nicholas Farland, Trevor Larson, Justin Taylor, Cameron Wendler, Anthony Ruocco, Janet Baldwin, Arnold Robinson

Engineering and Construction Management

To evaluate the impact of potential modifications to the HVAC system the Historical Value Adding Consultants developed a building energy model. The building energy model was constructed using a Microsoft Excel spreadsheet that utilizes typical meteorological year (TMY) data to determine the average energy usage of the Athenaeum for a typical year. The model has been validated against actual energy usage and is used to identify and quantify energy savings resulting from design alternatives.

Short-Term Load Forecasting Using Neural Network For Future Smart Grid Application, Jixuan Zheng

Electronic Theses and Dissertations

Short-term load forecasting of power system has been a classic problem for a long time. Not merely it has been researched extensively and intensively, but also a variety of forecasting methods has been raised.

This thesis outlines some aspects and functions of smart meter. It also presents different policies and current statuses as well as future projects and objectives of SG development in several countries.

Then the thesis compares main aspects about latest products of smart meter from different companies.

Lastly, three types of prediction models are established in MATLAB to emulate the functions of smart grid in the short-term …

Dc Microgrid Stabilization Through Fuzzy Control Of Interleaved, Heterogeneous Storage Elements, Robert David Smith

Dissertations, Master's Theses and Master's Reports - Open

As microgrid power systems gain prevalence and renewable energy comprises greater and greater portions of distributed generation, energy storage becomes important to offset the higher variance of renewable energy sources and maximize their usefulness. One of the emerging techniques is to utilize a combination of lead-acid batteries and ultracapacitors to provide both short and long-term stabilization to microgrid systems.

The different energy and power characteristics of batteries and ultracapacitors imply that they ought to be utilized in different ways. Traditional linear controls can use these energy storage systems to stabilize a power grid, but cannot effect more complex interactions. This …

Building Temperature Control With Intelligent Methods, Feng Zhang

Electronic Theses and Dissertations

Temperature control is important for both human comfort and the need in industry. In the thesis, two good intelligent control methods are compared to find their advantages and disadvantages. Matlab is used as the tool to make models and process calculations. The building model is one simple room in Akwesasne in New York State and the target is to keep the temperature indoor around 22 degree Centigrade from 12/29/2013 to 12/31/2013. Heat pump is used to provide or absorb heat. All data in the experiments is from JRibal Environmental eXchange network and PJM. The first method is fuzzy neural network …

Simplified Method To Derive The Kalman Filter Covariance Matrices To Predict Wind Speeds From A Nwp Model, Conor Lynch, Michael J. O'Mahony, Ted Scully

NIMBUS Articles

This paper espouses a simplified approach to predict wind speed 1 hour ahead for a wind turbine located on the Cork Institute of Technology (CIT) college campus by utilising a Kalman Filter to predict the bias between a campus based turbine and the output from a Numerical Weather Prediction (NWP) model for Cork Airport.

Furthermore, this paper investigates the optimum number of samples required (n) in a fixed sampling interval process to derive the covariance matrix of the system equation Qt and the covariance matrix of the observation equation Rt . The main contents of this paper include …