Power and Energy Commons^™

Optimization Of Renewable Energy Systems: Comparative Analysis Of Advanced Algorithms And Photovoltaic-Electrolyzer Performance For Cost Reduction And Efficiency Enhancement, Mohamed-Amine Babay, Mustapha Adar, Ahmed Chebak, Mustapha Mabroukia

Journal of Electrochemistry

The increasing demand for cost-effective and efficient renewable energy solutions presents significant optimization challenges in hybrid energy systems. This paper addresses these challenges by conducting a comparative analysis of three advanced optimization algorithms—Lévy Flight Optimization (LFO), Archimedean Optimization (AO), and Quantum Gorilla Optimization (QGO)—to minimize the Total Net Present Cost (TNPC) and Levelized Cost of Energy (LCOE) in hybrid renewable energy systems. The study integrates critical cost parameters such as Capital Expenditure (CAPEX), Operational Expenditure (OPEX), replacement costs, and salvage values into an advanced optimization framework. Three system configurations are evaluated: Wind Turbines and Fuel Cells (WT/FC), Photovoltaic Systems and …

Theoretical Insights Into The Atomic And Electronic Structures Of Polyperyleneimide: On The Origin Of Photocatalytic Oxygen Evolution Activity, Yi-Qing Wang, Zhi Lin, Ming-Tao Li, Shao-Hua Shen

Journal of Electrochemistry

Polymeric perylene diimide (PDI) has been evidenced as a good candidate for photocatalytic water oxidation, yet the origin of the photocatalytic oxygen evolution activity remains unclear and needs further exploration. Herein, with crystal and atomic structures of the self-assembled PDI revealed from the X-ray diffraction pattern, the electronic structure is theoretically illustrated by the first-principles density functional theory calculations, suggesting the suitable band structure and the direct electronic transition for efficient photocatalytic oxygen evolution over PDI. It is confirmed that the carbonyl O atoms on the conjugation structure serve as the active sites for oxygen evolution reaction by the crystal …

Three-Dimensional Melamine Carbon Sponge/Nai As Cathode Materials For Sodium-Ion Batteries, Qian-Ying Huang, Yue Liu, Zi-Xin Lin, Shu-Yi Zheng, Ting-Ting Mei, Yu-Ting Tang, Ying-He Zhang, Jun Liu

Journal of Electrochemistry

The sodium-iodine (Na-I) battery exhibits significant potential as an alternative energy storage device to the lithium-ion battery. However, its development is hindered by inadequate electrical and thermal stability, as well as the dissolution and shuttling of polyiodide. In this study, we report a preparation method for melamine carbon sponge (MC) via carbonizing a commercially available kitchen sponge. It was revealed that the as-prepared MC, composed of unique self-growing carbon nanotubes, could provide both physical and chemical adsorption capabilities for intermediate polyiodides to improve the electrochemical performance of NaI. Consequently, the NaI/MC electrode effectively minimized polyiodide dissolution and reduced the electrochemical …

Design And Performance Evaluation Of Pv-Powered Ev Charging Stations With Grid Integration And Comparative Analysis Of Dc-Dc Converters For Offboard Chargers, Mohammad Abidur Rahman

Theses and Dissertations

Grid-integrated photovoltaic (PV)-powered electric vehicle (EV) charging stations offer a sustainable solution for reducing grid dependency and fossil fuel consumption in workplace environments. This study proposes a PV-powered EV charging system with an AC bus configuration and grid support to ensure stable and efficient operation. A comparative analysis of four DC-DC converter topologies—Dual Active Bridge (DAB), LLC Resonant, Interleaved Buck-Boost, and Interleaved Buck—is conducted for offboard charging applications. Performance evaluation is carried out using MATLAB/Simulink, considering voltage and current ripple, power density, stress levels, bidirectional capability, and control complexity. Component-level reliability is assessed using MIL-HDBK-217 standards to estimate failure rates …

Detecting And Analyzing Frequency Events In Power Systems Using Tunable Parameters-Based Algorithms: Development, Optimization, And Analysis, Hussain A. Alghamdi

Dissertations and Theses

This dissertation addresses the challenge of detecting frequency events in diverse power systems by enhancing existing frequency event detection methods through detection process modifications and developing unique tunable parameters. Since system characteristics differ across regions, frequency event detection algorithms must be customized by domain experts for each balancing area using tunable parameters. By optimizing these parameters for specific power system, the algorithms can accurately detect frequency events and can also be used for further analysis to determine trends in frequency events over time, ensuring system stability.

This dissertation focuses on the enhancement and optimization of frequency event detection algorithms. These …

Who Owns The Wind: The Absence Of Community Wind Farms In California, Sky Berry-Weiss

Master's Projects and Capstones

Community ownership structures for wind farms have been around for decades, particularly in European countries, due to high socioeconomic benefits. Given these significant benefits, one might expect community wind to thrive in the United States—especially in a state like California, which prides itself on progressive climate policy and renewable energy leadership. Yet utility-scale community wind remains largely absent from research on California’s energy system, raising questions about its existence in the state. To pinpoint how many utility-scale community owned wind farms are in California, this study surveys every operational wind turbine in the state. After classifying each wind farm by …

Automated Solar Panel For Lmu Campus, Michael Hennessy, Jack Michaelis, Jack Leon, Nick Aiello, Mustafa Mozael

Honors Thesis

This Final Design Review outlines the design and implementation of an automated sun-tracking solar panel system for Loyola Marymount University's campus. The project aims to improve the efficiency of existing static solar panels by designing a new system of sun-tracking panels at a low cost and high power efficiency. The report covers the project's background, including LMU's current solar energy infrastructure and sustainability goals. It analyzes the advantages of automated solar panels over static ones, presenting comparative studies that demonstrate significant increases in energy capture. The report details the calculations for solar angle tracking, along with the mechanics and electronics …

Design, Simulation, And Testing Of Planar Transformer For Smart Green Power Node (Sgpn) Isolation Using Ansys, Brooke Scott

Electrical Engineering and Computer Science Undergraduate Honors Theses

The goal of this project was to design and simulate a small, high-frequency, planar, ferrite-core transformer which can be used in a variety of applications, the most relevant of which is photovoltaic (PV) converter systems, which often require bulky transformers to function properly. The current research involved several processes: (1) Understanding and designing a tutorial for the use of Ansys software to aid in the efficient development and modeling of transformers, (2) designing and simulating a planar transformer in Ansys to be used in a solar converter, specifically the Smart Green Power Node (SGPN), and (3) testing the planar transformer …

Investigation And Characterization Of Silicon Carbide Power Mosfets, Vincent Hassman

Electrical Engineering and Computer Science Undergraduate Honors Theses

As engineers constantly seek to make solar power systems smaller, cheaper, and more efficient, technological enhancements in the electronics that run them are required. One of the most fundamental electronic components of any solar system is the inverter, which takes DC current from the solar cell and turns it into AC current that is supported by the grid. This is done with metal oxide semiconductor field effect transistors (MOSFETs). Through more advanced MOSFET technology, inverters can switch at a higher frequency, increasing efficiency and reducing size and cost.

MOSFET performance can be enhanced by swapping the traditional silicon substrate with …

Grid Forming Inverters For Microgrid Operation Enhancement, Jan Westman

All Dissertations

Modern electric power systems are confronted with several major challenges including the increasing frequency and severity of weather events, aging infrastructure, high material costs, cyber-attacks, and substantial delays in global supply chains. Microgrids provide a solution to these challenges by insulating customers from the power outages occurring in their local distribution system. A microgrid is a small independent power system with its own power generation and energy storage resources that can supply customers’ electricity needs. When an outage occurs, a circuit breaker will disconnect the microgrid from the distribution system. Successful operation of the microgrid requires one or more devices …

Conversion Of Thermal Energy Stored In Conductive Concrete To Electricity With Thermoelectric Generators, Moustafa M. Al Adawi

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

This paper presents a proof-of-concept experimental study on the use of conductive concrete as thermal energy storage and its conversion into electricity. The conductive concrete is heated to 100°C by supplying electricity, and the stored thermal energy is converted back into electricity using thermoelectric generators (TEGs). Measurement results demonstrate that the conductive concrete effectively stores thermal energy up to 100°C, and this energy can be successfully converted into electricity. The findings highlight the potential of conductive concrete as a reliable medium for thermal energy storage.

Advisor: Lim Nguyen

Spin Coater Design With Pid Algorithm Using Polynomial Regression Approach And Bias Tuning For Tio2 Deposition Process, Geo Surya Andika, Nofrijon Sofyan, Donanta Dhaneswara, Akhmad Herman Yuwono

Journal of Materials Exploration and Findings

The thin-film deposition technique using spin coating offers a cost-effective alternative to Chemical Vapor Deposition (CVD) and Physical Vapor Deposition (PVD). The spin-coating process requires precise control of the motor drive system to ensure that the rotational speed, measured in rotations per minute (RPM), aligns with the set point and remains stable. This study presents the design and development of a spin coater prototype to achieve uniform thin-film deposition. The control method employed utilizes a Proportional-Integral-Derivative (PID) algorithm, incorporating a polynomial approach with bias tuning. The PID control was chosen to achieve stable operation in a non-linear system. The performance …

Adaptive Delay Compensation Frameworks For Distributed Real-Time Co-Simulation In Power Systems, Elutunji Buraimoh

All Dissertations

This dissertation presents a model-free, adaptive delay prediction and compensation framework for geographically distributed real-time power system co-simulation environments. Communication delays—both constant and real-time-varying—significantly degrade the accuracy, fidelity, and stability of co-simulated systems, particularly in dynamic and transient analyses of partitioned power systems. To address this, a predictor-based framework is developed that compensates for delays without requiring system models, computationally intensive signal transformations, or manual intervention.

The proposed solution leverages a Damping Impedance Method as the interface algorithm, combined with a sliding-mode control-inspired predictor system. Both single-parameter and multi-parameter predictor configurations are implemented, with the multi-parameter design providing an additional …

Real-Time Active Thermal Management And Degradation Forecasting Of Power Electronics Building Blocks In All-Electric Ships, Ali Moghassemi

All Dissertations

With advancements in semiconductor technology, power electronic devices play a critical role in modern power systems, enabling efficient energy conversion in applications such as renewable energy integration, electric vehicle drives, industrial automation, and Navy ship power systems. However, the increasing use of power converters presents challenges such as harmonic reduction, cost optimization, reliability improvement, and thermal management, especially in weight- and space-constrained environments like wind turbines and shipboard systems. High-frequency switching, while reducing passive filter size, increases thermal stress on semiconductor devices, impacting efficiency and longevity. Active thermal control, which regulates junction temperature through power loss management, and degradation forecasting, …

Enhancing Photovoltaic Inverter Reliability Through Advanced Hardware Protection And Simulation Techniques, Buck Brown

All Dissertations

Power electronics converter reliability is an issue in today’s grid, and it is an issue that will only become more prevalent as the nation and world move toward greater renewable energy penetration. While a significant amount of research has been conducted pertaining to power electronics converter reliability, (1) there lacks a universal way to protect the most critical component in a power electronics converter—the power device—from the two most common failure modes—short- and open-circuit faults; and (2) there does not exist a tool that considers both the component- and system-levels of a photovoltaic (PV) inverter for the purposes of lifetime …

Hybrid Dc-Dc Converters For Soft Charging Capacitive Actuators: Modeling, Analysis And Design, Bahlakoana Mabetha

Dartmouth College Ph.D Dissertations

Recent trends in haptics, microrobotics and ultrasound technology have shown an increasing use of piezoelectric and other electrostatic actuators. These actuators are suited for miniaturized applications due to their high power density and favorable scalability at a small size. Their electrical impedance at lower frequency (their typical operating range) is capacitive, therefore, they can be modeled as capacitive loads.

The driving circuits for capacitive actuators need to deliver and recover (bidirectional) dominantly reactive power, unlike typical power electronics converters for resistive loads which deliver (unidirectional) real power to the load. Therefore, the circuits, operation, and optimization required to drive these …

Modeling And Analysis Of A Hybrid Ac/Dc Green Seaport Power System With Photovoltaic Generation And Battery Energy Storage Systems, Corey Zaas

Master's Theses

This thesis investigates the modeling, simulation, and analysis of a Green Seaport power system integrating photovoltaic (PV) generation, battery energy storage systems (BESS), and coordinated protection within a hybrid AC/DC framework. The work improves a previously established model, enhancing it with detailed protection studies and simultaneous AC/DC power flow analysis using EasyPower software. The system was evaluated under a wide range of operating conditions, including varying solar irradiance, battery charge and discharge states, and both full and zero load conditions. Key performance indicators included voltage regulation, power factor behavior, equipment loading, protection device coordination, and total system power losses. Simulation …

Low Cost Additive Manufacturing Of Segmented Stator Composite Polymer Permanent Magnet Dc Motors, Ben Goldberg, Jordan Bailey, Connor Hawkins, Colin Haskins, Razvan Voicu

Symposium of Student Scholars

This study presents a novel approach to the design, manufacture, and optimization of segmented stators for composite construction axial flux permanent magnet DC motors. Traditional axial flux stator manufacturing is both challenging and expensive, creating a bottleneck in rapid prototyping and innovation. To overcome these limitations, the stator is divided into individually fabricated segments using advanced composite polymer materials and low-cost additive manufacturing techniques. This segmentation not only drastically reduces production complexity and cost but also allows for customized coil geometries that maximize the surface area for improved heat dissipation.

A key innovation of our design is the integration of …

Artificial Intelligence Applications For Grid-Connected Solar Inverters, Utkirjon Ubaydullaev, Sarvinoz Mirzaeva, Hasan Mustafoev

Chemical Technology, Control and Management

The increasing global demand for renewable energy has highlighted the importance of grid-connected solar inverters in ensuring efficient and stable power conversion. However, challenges such as fluctuations in solar energy generation, grid disturbances, and power quality issues necessitate advanced control strategies. The integration of artificial intelligence (AI) into solar inverters presents a transformative solution, enhancing performance, adaptability, and reliability in real-world applications.

This review explores the role of AI techniques, including machine learning (ML), deep learning (DL), fuzzy logic, and reinforcement learning (RL), in optimizing key inverter functionalities such as maximum power point tracking (MPPT), fault detection, power quality enhancement, …

Static Characteristics Of An Electromagnetic Three-Phase Reactive Power Sensor For Converting Asymmetric Currents, Timur Urunbayevich Kurbaniyazov

Chemical Technology, Control and Management

This article discusses the processes in the elements and structures of three-phase electromagnetic current sensors used in measuring and controlling three-phase asymmetric reactive power in power supply systems, research models of quantities and parameters, physical mechanisms, and mathematical formulas based on graphical models.

Clustering Mini-Grids To Enhance Power Systems Reliability In Distributed Generation, Santos Kihwele

Tanzania Journal of Engineering and Technology (TJET)

This study investigates the effectiveness of clustering mini-grids as a method to improve the reliability and operational stability of distributed generation systems in remote areas, particularly where renewable energy sources are predominant. As renewable resources like solar and wind are increasingly integrated into mini-grids, these systems face various challenges, particularly in maintaining stable voltage and frequency across interconnected networks. Such issues are compounded by the intermittent nature of renewable energy sources and the lack of extensive communication infrastructure in rural or resource-constrained settings. To address these control challenges, this study applies droop control techniques to two mini-grids in Uganda, utilizing …

Synthetic Inertia Provision For Load Frequency Control In Networks With High Penetration Of Renewable Energy Sources, Paulina Mkoi

Tanzania Journal of Engineering and Technology (TJET)

The integration of renewable energy sources (RESs) such as solar photovoltaic (PV) and wind energy has become a promising solution as the world shifts toward clean energy. Solar PV and wind resources are increasingly replacing conventional synchronous generators, leading to reduced system inertia and increased vulnerability to frequency instability during disturbances. To address this challenge, this study proposes a novel synthetic inertia provision strategy using a battery energy storage system (BESS) integrated alongside solar PV. The proposed method dynamically compensates for the loss of inertia by considering the variability of solar PV output due to changes in irradiance and temperature. …

Power-Beaming: Wireless Energy Transfer Using Lasers, Spencer L. Barnett

ATU Scholars Symposium

The objective of the project is to implement a wireless energy transfer system utilizing laser technology. This system involves modulating the laser’s beam profile and spatial distribution through precise optical manipulation. The energy transmitted by the laser is captured by a photovoltaic array, commonly referred to as a solar panel, which is engineered to convert incident photons into direct current (DC) electrical power. The current challenge is to develop a reliable wireless energy transfer mechanism capable of operating over extended distances, thereby overcoming the constraints imposed by wired connections, particularly in environments where wiring is impractical, such as in space. …

An Iterative Approach To Utility Contribution For Arc Flash Incident Energy Calculations, Zachary Giese

ATU Scholars Symposium

Accurately determining short-circuit fault contribution from utilities is a major challenge in arc flash incident energy analysis. Utilities may withhold or frequently alter data, and the presence of distributed generation complicates worst-case scenario identification. Additionally, commercially available software imposes limitations on scenario modeling and calculations, restricting engineers' ability to refine results. This research introduces an iterative approach that enhances worst-case arc flash identification while addressing software constraints. Initially, the study applied this approach to various facility models using commercial tools, comparing different methodologies. However, the focus has since evolved into developing an open-source arc flash calculator. This tool surpasses existing …

An Empirical Evaluation Of Communication Technologies And Quality Of Delivery Measurement In Networked Microgrids, Ruairí De Fréin, Yasin Emir Kutlu

Articles

Networked microgrids (NMG) are gaining popularity as an example of smartgrids (SG), where power networks are integrated with communication technologies. Communication technologies enable NMGs to be monitored and controlled via communication networks. However, ensuring that communication networks in NMGs satisfy quality of delivery (QoD) metrics such as the round trip time (RTT) of NMG control data is necessary. This paper addresses the communication network types and communication technologies used in NMGs. We present various NMG deployments to demonstrate real-life applicability in different contexts. We develop a real-time NMG testbed using real hardware such as Cisco 4331 Integrated Services Routers (ISR). …

Variation Of Membrane Electrode Assembly Catalyst Layer In Unitized Regenerative Fuel Cell, Yollanda Nurcholifah, Dedi Rohendi, Edy Herianto Majlan, Nirwan Syarif, Addy Rachmat, Dwi Hawa Yulianti, Nyimas Febrika S

Journal of Electrochemistry

A unitized regenerative fuel cell (URFC) is a device that may function reversibly as either a fuel cell (FC) or water electrolysis (WE). An important component of this device is the Membrane electrode assembly (MEA). Therefore, this study aimed to compare the performance outcomes of MEA using electrodes with single and three catalyst layers. This study measured Electrochemical Surface Area (ECSA), Electrochemical Impedance Spectroscopy (EIS), X-ray Diffraction analysis (XRD), and X-ray Fluorescence (XRF). Furthermore, the round-trip efficiency (RTE) of the MEA, as well as the performance in FC and WE mode, was measured. In comparison, The ECSA values of Pt-Ru/C …

Electrocatalytic Nitric Oxide Reduction To Yield Ammonia Over Fe3C Nanocrystals, Sen Lin, Lang Zhang, Tong Hou, Jun-Yang Ding, Zi-Mo Peng, Yi-Fan Liu, Xi-Jun Liu

Journal of Electrochemistry

Nitric oxide (NO), which generally originates from vehicle exhaust and industrial flue gases, is one of the most serious air pollutants. In this case, the electrochemical NO reduction reaction (NORR) not only removes the atmospheric pollutant NO but also produces valuable NH₃. Hence, through the synthesis and modification of Fe₃C nanocrystal catalysts, the as-obtained optimal sample of Fe₃C/C-900 was adopted as NORR catalyst at ambient conditions. As a result, the Fe₃C/C-900 catalyst showed an NH₃ Faraday efficiency of 76.5% and an NH₃ yield rate of 177.5 μmol·h^–1·cm^{–2 …}

Ordering Degree Regulation Of Pt2Nico Intermetallics For Efficient Oxygen Reduction Reaction, Chen-Hao Zhang, Han-Yu Hua, Jun-Hao Yang, Qian Zhang, Chang Yang, De-Li Wang

Journal of Electrochemistry

Alloying transition metals with Pt is an effective strategy for optimizing Pt-based catalysts toward the oxygen reduction reaction (ORR). Atomic ordered intermetallic compounds (IMC) provide unique electronic and geometrical effects as well as stronger intermetallic interactions due to the ordered arrangement of metal atoms, thus exhibiting superior electrocatalytic activity and durability. However, quantitatively analyzing the ordering degree of IMC and exploring the correlation between the ordering degree and ORR activity remains extremely challenging. Herein, a series of ternary Pt₂NiCo intermetallic catalysts (o-Pt₂NiCo) with different ordering degree were synthesized by annealing temperature modulation. Among them, the o-Pt …

Performance Of Co2/H2O Co-Electrolysis In A Flat-Tube Solid Oxide Electrolysis Cell Stack Under Air-Free Environment, Xiao-Hui Zhong, Fei Wang, An-Qi Wu, Bei-Bei Han, Jian-Xin Wang, Wan-Bing Guan

Journal of Electrochemistry

This work investigates the transient performance and stability of CO₂/H₂O co-electrolysis in an air-free environment using a flat-tube solid oxide electrolysis cell (SOEC) stack. The results show that the transient behavior of the stack with and without blowing gas in the air electrode is almost the same. With a current density of 0.67 A·cm⁻²@750 °C, the stack operated for over 200 h under co-electrolysis conditions with no air blowing, and the voltage drop rate of the stack was approximately 0.203%/100 hours. Microstructure analysis reveals significant loss of Ni particles and formation of an insulating …

A Dynamically Efficient Predictive Controller For Voltage Stability In A Dc To Dc Boost Converter, Giovanni Reyna

Electrical and Computer Engineering ETDs

Reliable voltage regulation has become a critical issue with increase demand in modern power electronic applications. This study presents a Model Predictive Controller (MPC) for voltage regulation in DC-to-DC boost converters. A closed loop analytical MPC framework is created with the purpose of computing optimal duty cycles to maintain a stable output voltage under varying load conditions, input changes, and disturbances.

To evaluate the performance of the MPC we set the controller against a comparative analyzing with a traditional cascading proportional integral (PI) controller. The proposed controller design is specifically targeted to improve dynamic efficiency during the converter’s transient events. …