Power and Energy Commons^™

An Investigation In The Performance Of Lithium Sulfur Battery With A Tic Coated Separator, Jian-Hua Fang, Yong Cao, Mao-Ping Yang, Ming-Sen Zheng, Quan-Feng Dong

Journal of Electrochemistry

To improve the specific capacity and cycle stability of lithium-sulfur (Li-S) battery, a TiC/Celgard coating separator was developed and its performance in Li-S battery was investigated. The electrochemical test results confirmed that the TiC coating layer could significantly increase the capacity and cycle stability. At a high rate of 2C, it still delivered the capacity of 650 mAh·g^-1. At 0.5C, the specific capacity was maintained at 841.3 mAh·g^-1 after 100 cycles.

Direct Electrochemistry Of Glucose Oxidase Based On Ws2 Quantum Dots And Its Biosensing Application, Chen-Lu Li, Hua-Ping Peng, Zhong-Nan Huang, Yi-Lun Sheng, Pei-Wen Wu, Xin-Hua Lin

Journal of Electrochemistry

In this study, a novel electrochemical glucose biosensor has been developed by immobilizing glucose oxidase (GOx) on tungsten disulfide quantum dots (WS₂ QDs) on the surface of glassy carbon electrode (GCE). Transmission electron microscopy, UV-vis spectroscopy and cyclic voltammetry were employed to characterize the morphology, structure, and electrochemical behaviors of the as-prepared WS₂ QDs and the biofilm modified electrode. The results suggested that the WS₂ QDs could accelerate the electron transfer between the electrode and the immobilized enzyme, which enabled the direct electrochemistry of GOx without any electron mediator. Besides, the immobilized GOx in WS₂ QDsfilm …

Application Of Adamantane Schiff Base Nickel Complexes/Graphene Oxide/Glassy Carbon Modified Electrode In Detection Of Carmine, Peng Guo, Zheng Liu, Hai-Ying Li, Li-Ming Ma

Journal of Electrochemistry

The Schiff base nickel complexes/graphene oxide/glassy carbon electrodes were prepared by embedded method and electrodeposition on which were used to quantitatively detect the contents of carmine. Cyclic voltammetry, chronoamperometry, scanning electron microscopy (SEM) and other methods were employed to characterize properties and morphologies of the modified electrodes. The results show that the adamantane double Schiff base nickel complexes/graphene oxide/glassy carbon electrode had high electric catalytic activity toward carmine oxidation reaction, and might provide an easy and quick way to detect carmine content with good reproducibility.

Energy Management System Modeling Of Dc Data Center With Hybrid Energy Sources Using Neural Network, Khalid Althomali

Master's Theses

As data centers continue to grow rapidly, engineers will face the greater challenge in finding ways to minimize the cost of powering data centers while improving their reliability. The continuing growth of renewable energy sources such as photovoltaics (PV) system presents an opportunity to reduce the long-term energy cost of data centers and to enhance reliability when used with utility AC power and energy storage. However, the inter-temporal and the intermittency nature of solar energy makes it necessary for the proper coordination and management of these energy sources.

This thesis proposes an energy management system in DC data center using …

Stakeholder Outcomes In A Wind Turbine Investment; Is The Irish Energy Policy Effective In Reducing Ghg Emissions By Promoting Small-Scale Embedded Turbines In Sme's?, Tony Kealy

Articles

As a member state of the European Union (EU), Ireland has adopted an energy policy which includes promoting wind powered electricity generators as an economically viable, GHG-reducing, alternative to environmentally damaging fossil-fuel driven electrical generators. This longitudinal, inductive in-depth study investigates the outcomes for the government and other stakeholders involved in a wind turbine project investment by a Small-to-Medium-Enterprise (SME) based in rural Ireland. A case study research methodology is used to acquire and analyse quantitative numerical data from multiple sources including electrical power and energy meters, historical electricity bills and company sustainability reports. The study found that the installation …

2017 Spring Engr333 Project Assignment, Matthew K. Heun

ENGR 333

The Spring 2017 ENGR333 project focused on campus energy consumption.

I asked the students “Can you construct a fine-grained, bottom-up electricity demand model that predicts the annual electricity consumption for the dormitories (section A) and the PE complex (section B) for each year of the last decade with an accuracy of ±2%?”

Customer

The customer for this project was Jack Phillips, Assistant Director (Mechanical) at Calvin’s Physical Plant.

Coreless Multidisc Axial Flux Pm Machine With Carbon Nanotube Windings, Vandana Rallabandi, Narges Taran, Dan M. Ionel, John F. Eastham

Power and Energy Institute of Kentucky Faculty Publications

Coreless axial flux permanent magnet (AFPM) machines are attracting increasing attention due to their compact structure and high torque density. The torque to weight ratio can be further enhanced by the use of alternate conductor materials, such as carbon nanotube (CNT), or aluminum windings in place of the copper material coils. This paper proposes a coreless AFPM synchronous motor with CNT windings. Analytical equations are developed to allow a systematic comparison of machine designs with different conductor materials. The performance of machine designs with different coil materials, namely, copper, aluminum, and CNT, is evaluated and compared. The calculations are also …

Ocean Renewable Power Company, James Donegan

MARENER 2017

No abstract provided.

Lighting Standards For Ship And Alternative Solutions For Energy Efficiency, Efe Akyurek

MARENER 2017

Lighting has an important role amongst human life. In this respect, an adequate lighting on board gives moral, motivation also helps to improve safety and security for ships’ crew. This paper aims to both determine an adequate lighting for crew and bring energy efficiency with optimal lighting considering existing regulations on shipboard lighting. After a brief introduction, on the first part the preferred lighting tendencies to be discussed at maritime regulatory base including SOLAS, MLC with comparing ILO 92/133 Conventions. The second part initially defines optimal lighting for crew accommodation and working areas with demonstrating an example on a river …

Overcoming The Challenges To Maritime Energy Efficiciency In The Caribbean Region, Deniece Aiken

MARENER 2017

Maritime energy efficiency in the Caribbean appears to be predicated on two key requirements; regulatory controls over the vessels operating in the region and the availability and use of efficient technology. While many Caribbean territories have ratified MARPOL AnnexVI, implementation of the standards therein, presents challenges that are familiar to maritime administrators of the region. These challenges include insufficient resources and inadequate implementation of relevant standards. These issues have traditionally plagued the region. The paucity of data and monitoring in this part of the world also contributes to ineffective policy interventions. There is also a need to identify the gap …

The Law Of Conservation Of Energy Towards Defining Maritime Cluster Dynamics, Peter J. Stavroulakis, Stratos Papadimitriou, Ioannis Koliousis

MARENER 2017

Industrial clusters have for many decades been considered as the stepping stone for regional and national competitiveness, due to the fact that within these systems of economies, many propitious qualities seem to flourish. Competition and cooperation are witnessed to complement one another, firms can thrive through the marvels of knowledge creation and innovation, and positive externalities are seen to blossom into an interconnected system of collective prosperity. This system bears semblance to many occurrences in nature, and thus can guide the reflection of natural dynamics that may pave an industrial cluster’s threads. Maritime clusters in particular, are distinct vanguards of …

Costs And Benefits Of Lng Economic Development In The Baltic And Arctic Regions, Fabio Ballini, Lawrence Kuroshi

MARENER 2017

Global warming is becoming increasingly evident. However, rising temperatures also offer new economic opportunities, such as new maritime routes in previously ice-locked waters. Valuable minerals in the Arctic region are also becoming more accessible. Maritime stakeholders are therefore seeking to operate in this remote region safely and efficiently. Accommodating these developments from a regulatory standpoint, IMO has amended the International Convention for the Prevention of Pollution from Ships (MARPOL) to include Chapter 9 of Annex I, prohibiting the use of heavy-grade marine fuels as well as heavy-duty oils as cargo carriage in the seas beyond 60th parallel south. In addition, …

Energy Consumption Of Small Scale Fishing Vessel Operations In Indonesia: A Case Study In Palabuhanratu, Indonesia, Vita R. Kurniawati, Richard W. Birmingham, Alan J. Murphy

MARENER 2017

About 79% of the global fishing fleet is small motorized boats typically operating in coastal areas, supplying local markets, and contributing to human well-being through food supplies and economic development. For example, Indonesian fisheries which predominantly are artisanal fishing, have supported 54% of animal protein intake, accounted for 2% of employment level and increased the fishermen’s prosperity index by 2.44%. However, they cause significant environmental impacts including fish resource depletion and intensive energy use. Balancing the benefits and challenges, sustainably managing these fishing operations is an important yet complex task given the requirements to proportionally account for fish resources, fishing …

Energy Awareness – Do We Need A Definition In Order To Implement It Onboard?, Signe Jensen

MARENER 2017

Energy optimization and the awareness about the issue has become an important topic in the maritime industry. An energy management study from 2015 performed by DNV GL, shows that energy awareness has moved from rank fifteen to be the most important measure to be implemented as a success factor to realize actual savings. However - What exactly is energy awareness, and how can it be defined and implemented? Are Ship Energy Efficiency Management Plans (SEEMP), noon reports and decision support software the right tools to raise awareness and improve energy efficiency for all shipping companies. Previous studies show that smaller …

Efficient Planar Heterojunction Perovskite Solar Cells With Li-Doped Compact Tio2 Layer, Detao Liu, Shibin Li, Peng Zhang, Yafei Wang, Rui Zhang, Hojjatollah Sarvari, Feng Wang, Jiang Wu, Zhiming Wang, Zhi Chen

Electrical and Computer Engineering Faculty Publications

Perovskite solar cells (PSCs) have been developed rapidly in recent time, and efficient planar PSCs are regarded as the most promising alternative to the Si solar cells. In this study, we demonstrated that Li-doping of compact TiO₂ can reduce the density of electron traps and increase the conductivity of the electron transport layer (ETL) of PSCs. Due to the improved electronic property of ETL, the Li-doped compact TiO₂ based planar heterojunction PSCs exhibit negligible hysteretic J-V behavior. Comparing with the undoped compact TiO₂ based PSCs, the power conversion efficiency (PCE) of the Li-doped compact TiO₂ film …

Data-Centric Situational Awareness And Management In Intelligent Power Systems, Xiaoxiao Dai

Electronic Theses and Dissertations

The rapid development of technology and society has made the current power system a much more complicated system than ever. The request for big data based situation awareness and management becomes urgent today. In this dissertation, to respond to the grand challenge, two data-centric power system situation awareness and management approaches are proposed to address the security problems in the transmission/distribution grids and social benefits augmentation problem at the distribution-customer lever, respectively.

To address the security problem in the transmission/distribution grids utilizing big data, the first approach provides a fault analysis solution based on characterization and analytics of the synchrophasor …

Risk Optimized Microgrid Resource Management, Thomas William Cashel Iii

Electronic Theses and Dissertations

This thesis proposes a risk based price adjustment method for a day ahead scheduling of a distribution side tiered community microgrid within a transactive energy style market. The system is organized into a master controller and local controller confïguration to simulate behind meter activity that is not visible to the master controller. Conditional value at risk is used to asses the risk of distributed energy resources in each local controller and the risk for each local controller is aggregated providing each local controller a single risk value. Each device's, or local controller's, risk value is used to adjust the price …

Hybrid Solar Thermophotovoltaic-Biomass/Gas Power Generation System With A Spectrally Matched Emitter For Lower Operating Temperatures, C. M. Iftekhar Hussain Cmih, Brian Norton, Aidan Duffy, Mohamed Oubaha

Conference Papers

Three conceptual designs have been developed for hybrid solar-biomass/gas thermophotovoltaic (TPV) system for a non-intermittent power generation which can operate at relatively low TPV operating temperatures. TPV cells with lower band gap has been chosen for this conceptual hybrid device. The low band TPV cell generates electricity at longer photonic wavelength which corresponds a lower operating temperature. The development methodology is presented for a spectrally matched emitter which emits maximum photonic energy in the 600°C -1000°C temperature range with correspondingly lower photonic energy emission in the 0°C -600°C range. This approach for spectral control in TPV systems requires fewer system …

Computational Modeling Of A Williams Cross Flow Turbine, Sajjan Pokhrel

Browse all Theses and Dissertations

Hydropower is not only the most used renewable energy source in the United States, but in the world. While it is well known that large hydropower facilities, like the Hoover Dam, provide large amounts of electrical power, there is also a tremendous opportunity for hydroelectric power generation from small scale facilities that has largely been overlooked. The work being presented here studies a new cross flow turbine called the Williams Cross Flow Turbine (WCFT), which was designed to extract electric energy from low head, run-of-the-river, small hydropower sites. To spur the implementation of the WCFT in small hydropower applications, and …

Application Of Nearly Linear Solvers To Electric Power System Computation, Lisa L. Grant

Doctoral Dissertations

"To meet the future needs of the electric power system, improvements need to be made in the areas of power system algorithms, simulation, and modeling, specifically to achieve a time frame that is useful to industry. If power system time-domain simulations could run in real-time, then system operators would have situational awareness to implement and avoid cascading failures, significantly improving power system reliability. Several power system applications rely on the solution of a very large linear system. As the demands on power systems continue to grow, there is a greater computational complexity involved in solving these large linear systems within …

Development Of Computer Program For Wind Resource Assessment, Rotor Design And Rotor Performance, Valentina Jami

Browse all Theses and Dissertations

People understand and have seen that renewable energy has many advantages over conventional energy sources. Because of these advantages, more and more emphasis has been given to generating electrical energy with renewable sources. Among the many renewable and conventional ways currently available for a society to generate electrical power, wind turbines are one of the cheapest ways of doing this. The main objective of this thesis work is to develop a computer program that assesses the wind resource at a given location, designs a wind turbine rotor for optimum power capture for one wind speed, and analyzes the performance of …

Wind Turbine Noise And Wind Speed Prediction, Tyler H. Blanchard

College of Graduate Studies: Theses & Dissertations

In order to meet the US Department of Energy projected target of 35% of US energy coming from wind by 2050, there is a strong need to study the management and development of wind turbine technology and its impact on human health, wildlife and environment. The prediction of wind turbine noise and its propagation is very critical to study the impacts of wind turbine noise for long term adoption and acceptance by neighboring communities. The prediction of wind speed is critical in the assessment of feasibility of a potential wind turbine site. This work presents a study on prediction of …

Development Of A Novel Kalman Filter Bank Predictor To Optimally Schedule The Renewable Energy Contribution Within A Micro-Grid, Conor Lynch

Theses

This PhD thesis presents a novel Kalman Filter Bank (KFB) methodology. The novel KFB is applied to predict and optimally schedule the operation of micro-grid energy resources with a public fixed-grid connection and an auxiliary battery storage backup facility. This methodology relies on a sliding single time step forecast projection to accurately acquire the anticipated schedule for a range of time dependent parameters, stochastic by nature, that have inherent embedded cyclical patterns. The innovative feature here consists of a novel bank of hourly adjacent Kalman Filter estimators, which operate in synchronism, for accurate parameter prediction over a selected time horizon. …

Control Of Pore Characteristics Of Porous Silicon Using Non-Toxic Electrochemical Etching For Photovoltaics And Supercapacitor Applications, Utpal Saha

Electronic Theses and Dissertations

Porous silicon has exhibited lower reflectance and higher surface area than the pristine silicon. This property of porous silicon can be applied to photovoltaic (PV) application for more efficient silicon solar cells and for higher performance of supercapacitors. NH4Fl electrolytic etching solution has been used to fabricate porous silicon, but the control of pore morphology of silicon is achieved only by controlling the time. Therefore, it is urgently required to use other etching parameters such as voltage and current to achieve flexible control of pore properties. Porous silicon can also be used to fabricate supercapacitors. An established approach to make …

Cathode Interface Engineering For High Performance Planar Perovskite Solar Cells, Md Nazmul Hasan

Electronic Theses and Dissertations

Organic-inorganic hybrid perovskite solar cells (PSCs) have already improved their power conversion efficiency (PCE) from 3.9% to ~22.1% at present. This demonstrated that PSCs can be a promising alternative to conventional silicon solar cells. PSCs have been marked as one of the most favorable next-generation solar cells due to their high extinction coefficient, broad light absorption range and ambipolar charge transport properties, low production cost, and simple fabrication processing. Various device architectures have been designed and investigated for constructing high performance PSCs consisting of different electron transport layers (ETL) and hole transport layers (HTL). In general, PSCs are fabricated in …

Development Of Microgrid Test Bed For Testing Energy Management System, Shaili Nepal

Electronic Theses and Dissertations

Today the world population has reached 7.5 billion, and this number is expected to grow at the rate of 1.13% every year [1]. With this increase in population, the total demand for electricity has also increased. More people means the need for more power: electricity to power homes, schools, industries, hospitals, and so on. In today’s world, where most of the daily activities are dependent on electricity, demand for electricity, therefore, continues to rise. Currently, managing this growing need for electricity is one of the challenges the world is facing. In addition to this, approximately 1.2 billion people live in …

Pretreatment, Enzymatic Hydrolysis, And Fermentation To Ethanol Using A Lignocellulosic Feedstock And Subsequent Recovery Of A Value Added Co-Product: Pure Crystalline Cellulose, Ryan J. Bouza

Electronic Theses and Dissertations

As more demand for alternatives to petroleum and the industrial world’s love of cars increase, cellulosic ethanol will become more important. The ethanol can, of course, be used in the transportation fuel sector, but there is also a potential for co-products to be developed out of the cellulose to ethanol process. Some of these co-products have the potential to replace current petrol products. These co-products may provide the extra revenue generation needed for further investment and development of this industry. This would not only provide better energy independence, but in the United States, it would better satisfy the cellulosic ethanol …

Efficient Energy Optimization For Smart Grid And Smart Community, Avijit Das

Electronic Theses and Dissertations

The electric power industry has undergone significant changes in response to the environmental concerns during the past decades. Nowadays, due to the integration of different distributed energy systems in the smart grid, the balancing between power generation and load demand becomes a critical problem. Specifically, due to the intermittent nature of renewable energy sources (RESs) , power system optimization becomes significantly complicated. Due to the uncertain nature of RESs, the system may fail to ensure the power quality which may cause increased operating costs for committing costly reserve units or penalty costs for curtailing load demands. This dissertation presents three …

Modeling Of The Solid-Electrolyte Interface Layer Of Lithium Ion Batteries For Capacity Fade Using Kinetic Monte Carlo, Bigyan Khanal

Electronic Theses and Dissertations

The accurate model on the growth of Solid-Electrolyte Interface (SEI) layer of Lithiumion batteries is used to study the capacity fade, ageing, and cycling life and provides significant information to ensure the battery safety. In this work, the model for SEI layer dynamics is developed using the Kinetic Monte Carlo approach, in which four major dynamical processes including adsorption, absorption, diffusion, and passivation are described by their individual rates, and determined from chemical and physical properties of materials used in the battery. Total cycle numbers to be simulated determine the number of Kinetic Monte Carlo steps. The formation of a …

Engineering Of Photo-Rechargeable Energy Storage, Ashim Gurung

Electronic Theses and Dissertations

Solar photovoltaics (PV) is a very promising renewable energy technologies as it is abundant and pollution-free. However, the major drawback of PV power is its intermittency. Integration of batteries with solar modules can reduce overall PV system costs and increase the practicality of PV power. Integration of the photovoltaic cells with supercapacitor storage proved feasibility of combined photovoltaic energy generation and storage but the supercapacitors had low energy storage capacity. Photovoltaic cells with integrated Li-ion batteries as energy storage were demonstrated but had a complex structure due to multiple PV cells; low efficiency due to a mismatch between the PV …