Power and Energy Commons^™

Impact Of Wind Generation On Transmission Voltage Support During Weak Grid, Yugo Isogai

Electrical Engineering Undergraduate Honors Theses

Today, there are concerns about the effects of high wind penetration on electric power system operations. This is due to the more distributed nature of wind turbine generation and the corresponding multi-path power flows on the electric power transmission grid. In particular, the higher line impendences associated with inverter-based wind generation results in larger voltage fluctuation under varying load. This may results in conditions where even after a fault condition has been cleared, the transmission system voltages may not recover. Therefore, this paper concentrates on the impact of weak grid condition for voltage instability. To approach it, a 6-bus system …

Transimpedance Amplification Of Optocoupler Output For High Temperature Applications, Kara Maurer

Electrical Engineering Undergraduate Honors Theses

When looking to the future of electronics, one characteristic is becoming more lucrative: high temperature capabilities. With the goals of not only becoming more efficient electronically, spatially, and cost-wise, adapting electronics for a high temperature environment can potentially be a route to all three of these goals. Not only does it take away the need for a cooling method, but it can also increase the longevity of a product which can make it even more cost effective. In an effort to contribute to the push for high temperature electronics, the University of Arkansas is developing a high temperature power module …

Ironless, Axial Flux, Electric Bldc Motor For Aircraft Electric Propulsion, Kevin W. Hobbs

Electrical Engineering Undergraduate Honors Theses

3D printing has shown much promise as a method of rapidly manufacturing lightweight ironless motors to meet the growing demand that airlines have for more cost-effective products that reduce emissions and flight prices. 3D-printed ironless, axial flux, electric BLDC motors would meet these needs with both their high efficiency and power density.

A Halbach array motor was designed and 3D-printed for the analysis of its magnetic properties to gain more insight about it performance. Fusion 360 was used to design the 3D drawings of the motor parts. The rotor, stator, and stator mount were designed to accommodate the sizes of …

An Examination Of Grid Stability As It Relates To The Increased Integration Of Inverter-Based Resources, Daniel Voss

Electrical Engineering Undergraduate Honors Theses

There is currently a growing interest in increasing the amount of renewable energy resources connected to the bulk electric system (BES) that stems from various environmental, political, and social concerns. However, the differences between conventional generation resources and inverter-based resources (IBR)—namely wind and solar—pose new issues that make this increased integration a larger problem. In other studies, the increased penetration of renewable energy resources has resulted in weak-grid systems that are more susceptible to collapse. This comes as a result from the inability for IBRs to effectively provide enough reactive power, an effect especially apparent during fault conditions, which the …

Automation, Annunciation, And Emergency Safety Shutdown Of A Laboratory Microgrid Using A Real-Time Automation Controller (Rtac), Do Vo

Master's Theses

Over the last decade, microgrid deployments throughout the world have increased. In 2019, a record number of 546 microgrids were installed in the United States [1]. This trend continues upward to combat extreme weather conditions and power shortages throughout the country. To better equip students with the necessary skillsets and knowledge to advance in the microgrid field, Cal Poly San Luis Obispo's Electrical Engineering Department and the Power Energy Institute have invested resources to develop a laboratory microgrid.

This thesis sets to improve the laboratory microgrid's existing automation using the Schweitzer Engineering Laboratory SEL-3530 Real-time Automation Controller (RTAC). The improved …

Integrated Ac To Ac Converters For Single-Phase Input To Two-Phase Output Motor Drives, Yibin Zhang, Damien L. Lawhorn, Peng Han, Dan M. Ionel

Power and Energy Institute of Kentucky Faculty Publications

The single-phase to two-phase converters have become attractive for low-power motor drives due to the full electromagnetic isolation between phases of two-phase motors. One of the commonly used topologies is the ac/dc/ac pulse width modulation (PWM) converter which contains twelve active power semiconductor switches and a common dc link. To minimize the system cost and size for low power applications, an integrated ac/ac converter with a single-phase input and a two-phase output which reduces the switch count to six is proposed in this paper. Additionally, modulation scheme and filters for the proposed converter are developed and modeled in details. In …

Integrated Modular Motor Drives Based On Multiphase Axial-Flux Pm Machines With Fractional-Slot Concentrated Windings, Peng Han, Greg Heins, Yibin Zhang, Dan M. Ionel

Power and Energy Institute of Kentucky Faculty Publications

The integrated motor drive (IMD) concept with possible modularization has attracted much attention in a broad spectrum of applications ranging from low-power general-purpose industrial drives to high-power electric propulsion. This paper presents the feasibility study and performance evaluation of using common axial-flux permanent-magnet (AFPM) machines with fractional-slot concentrated windings in IMDs, with the same diameter and a minimum increase in its axial length. Different winding configurations are compared in terms of the torque/power capability and fault tolerance without changing the winding current rating. The possibility of further torque improvement is discussed from the perspective of making full use of the …

Analysis Of Torque Production In Axial-Flux Vernier Pm Machines Of The Magnus Type, Murat G. Kesgin, Peng Han, Damien Lawhorn, Dan M. Ionel

Power and Energy Institute of Kentucky Faculty Publications

The paper presents a study of the torque production in a novel vernier-type axial-flux permanent magnet (PM) machine topology named MAGNUS. Two computational methods are employed, one based on the 3D FEA Maxwell stress calculations on individual stator and rotor components and one based on the analytical derivation of the air-gap flux density harmonics. Examples are provided for a design with a 40-pole spoke-type PM rotor and two stators, one active including a 3-phase winding with 6 concentrated coils wound around main teeth in a single layer arrangement and a second stator that has neither coils nor main slots and …

An 8-Bit Analog-To-Digital Converter For Battery Operated Wireless Sensor Nodes, Marvin Wayne Suggs Jr.

Graduate Theses and Dissertations

Wireless sensing networks (WSNs) collect analog information transduced into the form of a voltage or current. This data is typically converted into a digital representation of the value and transmitted wirelessly using various modulation techniques. As the available power and size is limited for wireless sensor nodes in many applications, a medium resolution Analog-to-Digital Converter (ADC) is proposed to convert a sensed voltage with moderate speeds to lower power consumption. Specifications also include a rail-to-rail input range and minimized errors associated with offset, gain, differential nonlinearity, and integral nonlinearity. To achieve these specifications, an 8-bit successive approximation register ADC is …

Si-Based Germanium Tin Photodetectors For Infrared Imaging And High-Speed Detection, Huong Tran

Graduate Theses and Dissertations

Infrared (IR) radiation spans the wavelengths of the windows: (1) near-IR region ranging from 0.8 to 1.0 μm, (2) shortwave IR (SWIR) ranging from 1.0 to 3.0 μm, (3) mid-wave IR (MWIR) region covering from 3.0 to 5.0 μm, (4) longwave IR (LWIR) spanning from 8.0 to 12.0 μm, and (5) very longwave IR extending beyond 12.0 μm. The MWIR and LWIR regions are important for night vision in the military, and since the atmosphere does not absorb at these wavelengths, they are also used for free-space communications and astronomy. Automotive and defect detection in the food industry and electronic …

Aiming For The Sun- Averting The Fate Of Icarus: De-Risking Solar Energy Projects, Manu Srivastava

Asian Management Insights

Climate change is increasingly accepted as an existential threat to civilisation and ‘business as usual’ is considered a luxury we cannot afford any more.

Memory Module Design For High-Temperature Applications In Sic Cmos Technology, Affan Abbasi

Graduate Theses and Dissertations

The wide bandgap (WBG) characteristics of SiC play a significant and disruptive role in the power electronics industry. The same characteristics make this material a viable choice for high-temperature electronics systems. Leveraging the high-temperature capability of SiC is crucial to automotive, space exploration, aerospace, deep well drilling, and gas turbines. A significant issue with the high-temperature operation is the exponential increase in leakage current. The lower intrinsic carrier concentration of SiC (10-9 cm-3) compared to Si (1010 cm-3) leads to lower leakage over temperature. Several researchers have demonstrated analog and digital circuits designed in SiC. However, a memory module is …

Improvement Of Stability Of A Grid-Connected Inverter With An Lcl Filter By Robust Strong Active Damping And Model Predictive Control, Seungyong Lee

Graduate Theses and Dissertations

This study addresses development and implementation of robust control methods for a three-phase grid-connected voltage source inverter (VSI) accompanied by an inductive-capacitive-inductive (LCL) filter. A challenge of current control for the VSI is LCL filter resonance near to the control stability boundary, which interacts with the inverter control switching actions and creates the possibility of instability. In general, active damping is needed to stabilize the system and ensure robust performance in steady-state and dynamic responses. While many active damping methods have been proposed to resolve this issue, capacitor-current-feedback active damping has been most widely used for its simple implementation.

There …

An Accurate And Efficient Electro-Thermal Compact Model Of Sic Power Mosfet Including Third Quadrant Behavior, Arman Ur Rashid

Graduate Theses and Dissertations

Due to narrower bandgap and lower critical electric field, silicon (Si) power devices have reached their limit in terms of the maximum blocking voltage capability. Exploiting this limitation, wide bandgap devices, namely silicon carbide (SiC) and gallium nitride (GaN) devices, are increasingly encroaching on the lucrative power electronics market. Unlike GaN, SiC devices can exploit most of the established fabrication techniques of Si power devices. Having substrate of the same material, vertical device structures with higher breakdown capabilities are feasible in SiC, unlike their GaN counterpart. Also, the excellent thermal conductivity of SiC, compared to GaN and Si, let SiC …

Analog Spiking Neural Network Implementing Spike Timing-Dependent Plasticity On 65 Nm Cmos, Luke Vincent

Graduate Theses and Dissertations

Machine learning is a rapidly accelerating tool and technology used for countless applications in the modern world. There are many digital algorithms to deploy a machine learning program, but the most advanced and well-known algorithm is the artificial neural network (ANN). While ANNs demonstrate impressive reinforcement learning behaviors, they require large power consumption to operate. Therefore, an analog spiking neural network (SNN) implementing spike timing-dependent plasticity is proposed, developed, and tested to demonstrate equivalent learning abilities with fractional power consumption compared to its digital adversary.

Design And Assembly Of High-Temperature Signal Conditioning System On Ltcc With Silicon Carbide Cmos Circuits, Sajib Roy

Graduate Theses and Dissertations

The objective of the work described in this dissertation paper is to develop a prototype electronic module on a low-temperature co-fired ceramic (LTCC) material. The electronic module would perform signal conditioning of sensor signals (thermocouples) operating under extreme conditions for applications like gas turbines to collect data on the health of the turbine blades during operation so that the turbines do not require shutdown for inspection to determine if maintenance is required. The collected data can indicate when such shutdowns, which cost $1M per day, should be scheduled and maintenance actually performed. The circuits for the signal conditioning system within …

Performance And Economics Of Solar Inverters And Module Level Power Electronics In A 1 Mw Photovoltaic System, Maxwell Criswell

Biological and Agricultural Engineering Undergraduate Honors Theses

Photovoltaic solar panels convert sunlight to electricity in the form of direct current; therefore, a necessary component of every photovoltaic system is an inverter to convert the electricity to usable alternating current. There are various commercially available inverter technologies manufactured today such as microinverters, string inverters, and central inverters, as well as module level power electronic devices such as DC optimizers that are capable of improving system performance in string and central inverter systems. This thesis compares the performance and economics of five different inverter and module level power electronic systems through model simulation using Helioscope software. The five alternatives …

Three-Phase Unfolding Based Soft Dc-Link Converter Topologies For Ac To Dc Applications, Dorai Babu Yelaverthi

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Battery electric vehicles (BEVs) and plugin hybrid electric vehicles (PHEVs) are more efficient than internal combustion-based vehicles. Adaption of EVs will help reduce the carbon emissions produced by the transportation sector. The charging infrastructure has to grow at a rapid pace to encourage EV adaption. Installing higher capacity fast chargers will help alleviate the range anxiety of battery electric vehicle customers. More public charging stations are required for the full adaption of EVs. Utility power is distributed as ‘alternating current.’ A battery requires ‘direct current’ (DC) source to charge it. Hence a power converter that converts AC source to DC …

Preparation And Characterization Of "Water-In-Salt" Polymer Electrolyte For Lithium-Ion Batteries, Xu Hou, Xin He, Jie Li

Journal of Electrochemistry

Since the development of wearable and flexible electronic products, the demand of flexible energy storage devices such as batteries and super capacitors is in urgent. To enhance the safety and cycling stability for flexible lithium-ion batteries, “water-in-salt” polymer electrolyte was prepared by introducing 21 mol·kg^-1 LiTFSI electrolyte into cross-linked polyacrylamide (PAM) after freeze-drying. A great amount of holes with the size range of 10 ~ 20 μm can be found on the surface and in the bulk of polyacrylamide, which is benefited from the freeze-drying process and acts as a great support for the electrolyte uptake. The “water-in-salt” polymer …

Application Of Atomically Precise Metal Nanoclusters In Electrocatalysis, Zhi-Hua Zhuang, Wei Chen

Journal of Electrochemistry

Metal nanoclusters (M NCs) consist of only several to a few hundred of metal atoms and possess core sizes less than 2 nm. Owing to the quantum size effect, the electronic states of M NCs evolve to discrete levels similar to the molecule energy gaps, other than a continuous density of states to produce plasmon characteristic of bulk metal nanoparticles (M NPs). In comparison with the conventional M NPs, M NCs exhibit dramatically unique electronic and optical properties, such as molecule-like energy gaps, strong photoluminescence and high catalytic properties, which make them promising for potential application in numerous fields, such …

Oxygen-Exposure Induced Rapid Oxidation Of Spiro-Ometad In Cspbibr2 Perovskite Solar Cells, Wei-Guo Wang, Tian Bai, Gao-Fei Xue, Mei-Dan Ye

Journal of Electrochemistry

2,2′,7,7′-tetrakis(N,N-di-p-methoxyphenyl-amine)-9,9′-spirobifluorene (Spiro-OMeTAD) is the most widely used hole transport material in perovskite solar cells (PSCs). However, its oxidation in the air takes a long time and results in the attack of perovskite by water. In this regard, we performed the oxidation process of Spiro-OMeTAD in oxygen, where perovskite can be protected from water, guaranteeing the integrity of perovskite. It was demonstrated that the champion Spiro-OMeTAD based CsPbIBr₂ PSCs after oxygen oxidation achieved a 7.19% power conversion efficiency (PCE), showing a higher PCE than 6.29% of the champion device oxidized in air. A series of electrochemical characterization methods were applied …

Theoretical Studies Of Metal-N-C For Oxygen Reduction And Hydrogen Evolution Reactions In Acid And Alkaline Solutions, Xue-Ping Qin, Shang-Qian Zhu, Lu-Lu Zhang, Shu-Hui Sun, Min-Hua Shao

Journal of Electrochemistry

Single atom catalysts (SAC) have been regarded as the promising alternatives to platinum group metals due to their low costs and potentially high catalytic activities in various electrocatalytic reactions. The atomic mechanism understanding of activity discrepancy among different metal and nitrogen co-doped carbon-based catalysts is still lacking. Here, non-precious metal and nitrogen co-doped carbons (Me-N-C, Me = Fe and Co) as the model catalysts are investigated by combining experimental and theoretical studies to explore the catalytic activities and corresponding reaction mechanisms toward oxygen reduction reaction (ORR) and hydrogen evolution reaction (HER) at universal pHs. Atomic theoretical simulations suggest that Fe-N-C …

Lithium Storage Performance Of Hard Carbons Anode Materials Prepared By Different Precursors, Zhen-Lang Liang, Yao Yang, Hao Li, Li-Ying Liu, Zhi-Cong Shi

Journal of Electrochemistry

Hard carbon is one of the most promising anode material for lithium ion batteries (LIBs) owing to its high stability, widespread availability, low-cost, and excellent performance. The electrochemical properties of hard carbon materials depend strongly on the type of precursors. It is, therefore, very important to choose an excellent hard carbon precursor. Polyacrylonitrile, petroleum pitch and peanut shells were used as raw materials to prepare different hard carbon anode materials for LIBs. These hard carbon anode materials were successfully synthesized in two steps. The selected precursor was firstly carbonized at 600℃ for 1 h in argon atmosphere using heating rate …

Pd-Based Electrocatalysts For Oxygen Reduction And Ethanol Oxidation Reactions: Some Recent Insights Into Structures And Mechanisms, Zhi-Peng Wu, Chuan-Jian Zhong

Journal of Electrochemistry

The development of efficient electrocatalysts for applications in fuel cells, including proton-exchange membrane fuel cell (PEMFC) and direct ethanol fuel cell (DEFC), has attracted extensive research attention in recent years. Oxygen reduction reaction and ethanol oxidation reaction are two of the key reactions where the design of active, stable and low-cost electrocatalysts is critical for the mass commercializations of PEMFCs and DEFCs. This challenge stems largely from the limited understanding of the catalyst structures and reaction mechanisms. Progress has been made in investigations of electrocatalysts derived from Pd-based alloy nanomaterials both experimentally and computationally. We highlight herein some of the …

Enercon Station Vacuum Pump Replacement, Clint Hembree, Jared D'Amico, Connor Moore, Paul Jeffrey Fontenot, Sydnee Castello, J.J. Clements

Senior Design Project For Engineers

This details the progress of the ENERCON pump replacement project as completed by the Kennesaw State University interdisciplinary senior design group. This project is a two-semester capstone effort for the engineering program at Southern Polytechnic School of Engineering, overseen by Dr. McFall during Fall 2020 and Dr. Khalid during Spring 2021 semesters. The 2020-2021 KSU Interdisciplinary Senior Design team was tasked with completing an Engineering Change Package (ECP) for existing vacuum pumps at ENERCON Station. The mechanical, electrical, and civil students worked together, performing evaluations on existing plant systems to ensure the plant could support the new vacuum pumps. By …

A Magneto-Mechanical Piezoelectric Energy Harvester Designed To Scavenge Ac Magnetic Field From Thermal Power Plant With Power-Line Cables, Quan Wang, Kyung-Bum Kim, Sang-Bum Woo, Yooseob Song, Tae-Hyun Sang

Civil Engineering Faculty Publications

Piezoelectric energy harvesters have attracted much attention because they are crucial in portable industrial applications. Here, we report on a high-power device based on a magneto-mechanical piezoelectric energy harvester to scavenge the AC magnetic field from a power-line cable for industrial applications. The electrical output performance of the harvester (×4 layers) reached an output voltage of 60.8 V_max, an output power of 215 mW_max (98 mW_rms), and a power density of 94.5 mW_max/cm³ (43.5 mW_rms/cm³) at an impedance matching of 5 kΩ under a magnetic field of 80 …

A Demand-Supply Matching-Based Approach For Mapping Renewable Resources Towards 100% Renewable Grids In 2050, Loiy Al-Ghussain, Adnan Darwish Ahmad, Ahmad M. Abubaker, Mohammad Abujubbeh, Abdulaziz Almalaq, Mohamed A. Mohamed

Mechanical Engineering Graduate Research

Recently, many renewable energy (RE) initiatives around the world are based on general frameworks that accommodate the regional assessment taking into account the mismatch of supply and demand with pre-set goals to reduce energy costs and harmful emissions. Hence, relying entirely on individual assessment and RE deployment scenarios may not be effective. Instead, developing a multi-faceted RE assessment framework is vital to achieving these goals. In this study, a regional RE assessment approach is presented taking into account the mismatch of supply and demand with an emphasis on Photovoltaic (PV) and wind turbine systems. The study incorporates mapping of renewable …

Nitro Group Reduction For Use In Organic, Cathodic Materials, Brock G. Goeden

Honors Thesis

The industrial demand for higher capacity, light-weight battery materials has skyrocketed in recent years due to heavy investments in portable electronics, electronic vehicles, and renewable energy sources. However, rechargeable battery technology has seen little improvement since the invention of the Lithium-Ion battery in the 1980s. The low energy density of the traditionally utilized LiCoO2 cathodic material (specific capacity: 272 mAh g-1), has limited its potential to meet these increasing demands. To solve this problem, our research group is investigating new types of lightweight, organic, polymeric materials with conductive backbones as a possible replacement for the cathodic materials in Lithium-Ion batteries. …

Design Of Smart Trashcan, Haoran Song

Senior Theses

A smart trashcan has been designed which can bring convenience to people for throwing their garbage away during the COVID-19 pandemic. A prototype is made from cardboard to demonstrate its function. This trashcan can sense people who are coming and leaving, and it can open and close automatically. The trashcan is powered by solar energy. A solar panel is mounted on top of the trashcan supporter. This design is specifically for use in China.

Specification, Control, And Applications Of Z-Source Circuit Breakers For The Protection Of Dc Power Networks, Sagar Bhatta

Electrical & Computer Engineering Theses & Dissertations

There is a highly-increasing demand for the DC power transmission and distribution in modern power systems for the integration of newly-installed renewable energy resources and storage systems to the existing utilities. Application of DC power systems in electric ships, battery energy devices, high-voltage DC networks, smart grids, electric vehicles, microgrids, and wind farms is a recent trend that is being highly investigated. The fault protection of DC systems is an essential but challenging issue that needs careful attention to maintain system operation reliability and device safety. In this research, the specification, control, and application of Z-source breakers (ZCBs) are investigated …