Power and Energy Commons^™

Modeling Of Bearing Voltage In Electric Machines Based On Electromagnetic Fea And Measured Bearing Capacitance, Peng Han, Greg Heins, Dean Patterson, Mark Theile, Dan M. Ionel

Power and Energy Institute of Kentucky Faculty Publications

Bearing voltages and associated bearing currents in electric machines driven by pulsewidth modulation converters with high switching frequencies and high dv/dt can cause premature bearing failures. This article proposes a new modeling approach for the prediction of steady-state and transient bearing voltages based on two-dimensional (2-D) electromagnetic finite element analysis with coupled external circuits using measured bearing capacitance values. The distributed-element external circuit was employed mainly to take into account the influence of wire distribution and frequency dependency, which are typically neglected by traditional equivalent circuits. The developed model was then used to simulate bearing voltages for various scenarios and …

Optimization For Variable Height Wind Farm Layout Model, Bin Xu, Jianming Zhu, Junzhe Wen, Shanshan Lin, Yunkai Zhao, Jin Qi, Yu Xue, Sichong Qin

Student Published Works

The optimization of wind farm layouts is very important for the effective utilization of wind resources. A fixed wind turbine hub height in the layout of wind farms leads to a low wind energy utilization and a higher LCOE (levelized cost of electricity). WOMH (Wind Farm Layout Optimization Model Considering Multiple Hub Heights) is proposed in this paper to tackle the above problem. This model is different from the traditional fixed hub height model, as it uses a variable height wind turbine. In WOMH, the Jensen wake and Weibull distribution are used to describe the wake effect on the …

Real Work With Real Consequences: Enlisting Community Energy Engineering As An Approach To Envisioning Engineering In Context, Michelle E. Jordan, Steve Zuiker, Wendy Wakefield, Mia Delarosa

Journal of Pre-College Engineering Education Research (J-PEER)

This study describes an illustrative case study from a year-round program that positions middle and high school youth to explore the social value of energy systems in their homes, schools, and neighborhoods. Designed to center existing youth assets, interests and values, Community Energy Engineering (CEE) frames engineering as a tool that students can enlist in order to understand and interrogate their local socio-energy system while also acting to transform it. CEE partners with Title 1 schools in Latino/a neighborhoods in the U.S. southwest. CEE situates youth community-based solar energy innovation projects as consequential, evolving in and with historically contingent engineering …

Optimal Capacitor Placement - A Bibliometric Survey, K V S Ramachandra Murthy, K Prabha Rani, Ramesh Adireddy, Nandan D.

Library Philosophy and Practice (e-journal)

In this paper, Bibliometric survey has been carried out on Optimal Capacitor Placement from 1981 to 2021. Scopus database has been used for the analysis. There were total 909 documents found on the topic of Optimal Capacitor placement. The statistical analysis is carried out source-wise, year-wise, area-wise, Country-wise, University wise, author-wise, and based on funding agency. Network analysis is also carried out based on Co-authorship, Co-occurrence, Citation Analysis and Bibliographic coupling. Results are presented. During 2016, there were 77 documents published which is the highest. International Journal of Electrical Power and Energy Systems of Elsevier has published 37 documents during …

The Effects Of The Transient And Performance Loss Rates On Pv Output Performance, Chibuisi Chinasaokwu Okorieimoh, Brian Norton, Michael Conlon

Conference papers

Solar photovoltaic (PV) panels experience long-term performance degradation as compared to their initial performance, resulting in lower like-per-like efficiencies and performance ratios. Manufacturers of solar photovoltaic modules normally guarantee a lifespan of more than 20 years. To meet such commitments, it is important to monitor and mitigate PV module degradation during this period, as well as beyond, to recognize maintenance and repair needs. Solar PV modules degrade over time, becoming less effective, less reliable, and eventually unusable. The effects of transient and performance loss rates on the output performance of polycrystalline silicon (p-Si) solar PV modules are the focus of …

Zero Voltage Switching Hybrid Voltage Divider Converter, Timothy Jeong

Master's Theses

This project proposes a new hybrid voltage divider DC-DC converter that utilizes switching capacitors and inductors to produce zero voltage switching (ZVS) at the turn on state of its switches. By achieving ZVS, the switching losses are significantly reduced; thus, increasing the overall efficiency of the converter at various loads. The goal for this thesis is to perform analysis of the operation of the converter, derive equations for sizing the main components, and demonstrate its functionality through computer simulation and hardware prototype. Results of the simulation and hardware testing show that the proposed converter produces the desired output voltage while …

On The Design Of Coreless Permanent Magnet Machines For Electric Aircraft Propulsion, Damien Lawhorn, Peng Han, Donovin Lewis, Yaser Chulaee, Dan M. Ionel

Power and Energy Institute of Kentucky Faculty Publications

This paper presents design and prototyping studies for coreless and slotless permanent magnet (PM) machines, which have the potential for high power density and efficiency, and discusses their feasibility for electric aircraft propulsion. The emphasis is on axial flux permanent magnet (AFPM) machines with printed circuit board (PCB) stators that have advantages over their wired counterparts in terms of design flexibility, coil accuracy, manufacturing process reliability, and heat dissipation. Detailed electromagnetic finite element analysis models were developed and employed alongside analytical sizing equations to evaluate the performance of two dual-rotor single-stator coreless AFPM designs employing wave and spiral PCB winding …

Combined Use Of Ev Batteries And Pv Systems For Improving Building Resilience To Blackouts, Huangjie Gong, Dan M. Ionel

Power and Energy Institute of Kentucky Faculty Publications

Californian residencies face increased risk of blackout. The state depends more on imported electricity that may not always be available to fill the gap between renewable generation and demand. For buildings with PV panels, storing the surplus solar power to support the load during a blackout can be achieved with a large energy storage system (ESS). The electric vehicle (EV) provides potential solutions as it can expand the energy capacity of the residential ESS with its battery. In this paper, a reference house in California was modeled in EnergyPlus. The building resilience for a house with different load percentages were …

Manganese Oxide Carbon-Based Nanocomposite In Energy Storage Applications, Mulugeta Wayu

Chemistry Faculty Research

Global increasing demand in the need of energy leads to the development of non-conventional, high power energy sources. Supercapacitors (SCs) are one of the typical non-conventional energy storage devices which are based on the principle of electrochemical energy conversion. SCs are promising energy storage devices for better future energy technology. Increasing progress has been made in the development of applied and fundamental aspects of SCs. Manganese oxide electrode materials have been well studied; however, their capacitive performance is still inadequate for practical applications. Recent research is mainly focused on enhancing manganese oxide capacitive performance through the incorporation of electrically conductive …

Power Line Coupling Power Supply Design, Janine Gian Christii C. Darato, Jeni K. Kawate, Nicholas A. Marta

Electrical Engineering

In this project, a power supply was designed for a startup company, Perch Sensing, to detect wildfires with the use of distributed sensors across power lines. The purpose of the power supply is to provide 15W of power to a microcontroller, which controls the sensor nodes. The power supply hangs from power lines and draws energy by inductively coupling to these lines. Our design starts with a current transformer that steps down the current from the power line, which is fed into a shunting mechanism as a safety precaution when the load is absent, then to the power supply itself. …

Buck Converter With Voltage Foldback Protection, Fabian Aaron Enriquez, Pedro Rincon Rosales

Electrical Engineering

In this work, we implemented the idea of current foldback protection onto a buck converter. Current foldback protection essentially helps reduce the power dissipation which may be caused by a short circuit or overload scenario. To achieve the goal of this project, we used a combination of comparators, operational amplifiers and MOSFETs to create a current foldback sub controller. This controller would then serve as a feedback device between the output of the converter and the main controller to detect if a fault condition has occurred. Following the design, we performed simulation of the current foldback controller using PSpice and …

Solar Pv Emulator, Tristan Studer, Cody Kremer

Electrical Engineering

The implementation of a solar PV emulator. Creating a controllable testing environment which sufficiently recreates realistic conditions a photovoltaic cell would experience in real world use. The project aims to accurately show the efficiency and reliability of a solar PV cell, opposed to an ideal model which creates unrealistic expectations. The PV emulator implements conditions such as: irradiance, soiling and temperate changes. It gives feedback on a displayed IV curve and/or PV curve so the user may graphically analyze the output their PV cell produces given various conditions. It allows the user selectable conditions the solar cell may experience this …

Solar Photovoltaic Iv Curve Tracer, Jonathan W. Skelly

Electrical Engineering

The Solar Photovoltaic Current-Voltage (IV) Curve Tracer, sponsored by Cal Poly Professor Dale Dolan, characterizes solar array current vs. voltage curves for any given temperature and irradiance. The curve tracer is battery powered, and functions autonomously across loading conditions from short circuit to open load on any sub-450-watt solar array. The curve tracer supports separate data logging modes for both single cells and single modules to maximize data accuracy for each. For testing full strings of solar panels, up to 10 IV curves may be stored in persistent EEPROM memory. Stored data may be recalled later for output to a …

Optimization Of Single Axis Tracker Settings In The Cal Poly Goldtree Solar Farm, Charles A. Studdard, Liliana Reyes

Electrical Engineering

Solar farms use direct sunlight when operating; additionally, solar modules produce the most energy aligned perpendicular to the sun. Single axis solar tracking systems allow the rotation tilted photovoltaic panels to rotate during the day, maintaining the panels at the utmost efficiency angle. Achieving maximum power generation and reducing shade on the panels, make it crucial to have constant optimum positioning. Larger farms contain multiple rows and columns leading the panels to cast shadows on one another. Backtracking happens when you eliminate or reduce shadow casted on panels from adjacent modules. Panels positioned equidistantly and on even terrain allows backtracking …

2021 Department Of Energy Collegiate Wind Competition Electrical System, Grayson Capers, Shane Alayvilla, Justin Rodrigues

Electrical Engineering

In this work, the implementation of the electrical system for Cal Poly’s 2021 Department of Energy Collegiate Wind Competition turbine is described. The mission of this project was to complete the turbine testing tasks to the best of the team’s ability. This system includes an off the shelf slotless permanent magnet synchronous generator and rectifier to produce a DC voltage. To maximize the power output at below-rated wind speeds, current sensors, voltage sensors, and a dynamic load with variable resistance were designed and tested. To curtail the power and rotor speed in high wind events, the turbine was equipped with …

Hybrid Ac/Dc House, Vinh Q. Tran, Casey Winans, Erin O'Rourke

Electrical Engineering

The Hybrid AC/DC house is a proof of concept implementing a DC bus in residential power systems. The implementation of the DC bus is motivated by efficiency through a direct path for DC sources and loads. The avoidance of DC-to-AC and AC-to-DC conversions used in typical residential systems especially those with DC sources such as solar panels could experience higher efficiencies through only DC-to-DC conversions between the sources and the loads.

Dc-Dc Buck Boost Converter Using The Lt8390 Controller And Gan High Electron Mobility Transistors, Juan Manuel Urbano Jr, Brian Thongchai Keokot

Electrical Engineering

California Polytechnic State University, San Luis Obispo’s ongoing Energy Harvesting from Exercise Machines (EHFEM) project creates a sustainable energy source by converting physical exercise from exercise machines into renewable electricity. Implementing energy harvesting technology into the Recreation Center’s exercise machines helps Cal Poly make progress on its goal of carbon neutrality by 2050 [1]. An improvement to the system with new technology increases Cal Poly Recreation Center’s ability to save money and improve sustainability.

The focus of this project improves the design of Nicholas Serres, who used the LT8390 controller in his buck boost DC-DC converter [2]. This project improves …

Wildfire Early Detection System (Weds), Mason Mciver, Vincent Liang, Jeanreno Racines

Electrical Engineering

With climate change causing an increase in temperature over the past several decades, wildfires have been burning hotter and moving quicker leaving a trail of destruction in their path. Detecting a wildfire early allows firefighters to respond efficiently and effectively to ensure containment. With the rise of advanced computer vision and algorithms, autonomous systems can be used to monitor and report any fire activity. Having multiple devices spread out across a large area will allow first responders to map out the fire location and track the fire. By utilizing smart technologies, property damage can be minimized and residents living in …

Miniaturized Ultraviolet Imager High Voltage Power Supply, Nicholas Palmer, Jason Thomas Heil

Electrical Engineering

Sending satellites into orbit becomes exponentially more expensive with weight and size, so designing high-voltage DC-DC converters that can achieve kilovolt level outputs in a small form factor is crucial to reducing costs. The Miniaturized Ultraviolet Imager (MUVI) aims to monitor Earth’s ionosphere and report weather patterns to climate scientists within a 2U cube satellite footprint. The imaging equipment consists of a microchannel plate and phosphor screen that require 2.5kV and 5.5kV respectively at microamp level currents. This report explains the implementation of a high voltage boost cascaded flyback converter to meet all of the MUVI satellite output voltage requirements. …

Optimized Insulation Design Of Power Transformer Windings Under Fast Voltage Pulses, Juan Manuel Villanueva Ramirez

Dissertations

Power transformers are essential electrical power system devices. Using the principle of electromagnetic induction, they can transfer electric energy between two otherwise isolated circuits, as well as reduce or increase voltage levels without modifying the frequency. This allows reduction of power losses when electric energy is transferred between power plants and consumers. Because of their importance and widespread use, transformers failures can have a severe economic impact due to the temporary interruption of electric service.

The insulation design of power transformers is performed by considering the maximum values of voltage or current to which the device will be exposed during …

Controlled Reduction Of Graphene Oxide And Graphene Oxide-Carbon Nanotube Hybrids And Their Applications, Samar Azizighannad

Dissertations

Graphene and graphene derivatives are widely used in diverse research and industrial applications. Graphene production on a large scale is carried out by exfoliating graphite oxide and producing graphene oxide (GO), which comprises of graphene sheets with different oxygen-containing functional groups such as hydroxyl, carboxyl, and carbonyl. GO is reduced to reduced graphene oxide (rGO), which has properties that are closer to graphene. Properties of GO and rGO depend upon the oxygen content, and the effect of reducing oxygen content on the aqueous behavior of rGOs is not well understood.

In an effort to understand how properties of rGO change …

A Novel Variable Reluctance Resolver With Simplified Winding Arrangement And Adaptive Pi Controller, Bikram Bhandari

LSU New Orleans Theses and Dissertations

Conventional variable reluctance resolvers require a complicated winding arrangement (i.e., one set of excitation winding and two sets of signal winding), high-frequency ac supply, extra circuit component to demodulate the high frequency induced voltage (i.e., amplitude demodulation circuit), and a resolver-to-digital converter with the PI controller. The thesis presents an innovative design solution to reduce the structural complexity of the resolver and improve the functionality of the controller unit. The proposed novel design simplifies the winding arrangement and eliminates the necessity of the demodulation signal processing circuit component. In addition, the conventional PI controller is being replaced by the adaptive …

A Bibliometric Review Of Characterization Of Outdoor Solar Pv Panel For Shading And Validation By Pv Emulator, Viplove Malik, Poojan Pavagadhi, Aman Kumar Pandey, Saharsh Vyas, Javed Sayyad, Paresh Nasikkar

Library Philosophy and Practice (e-journal)

Many researchers and experts have begun to work in Renewable Energy (RE) Research and Development (R&D) as an interdisciplinary area ineluctable solution to lower the use of conventional power generation or non-renewable resources. Solar photovoltaic energy has gained a lot of recognition as one of the best green alternatives. However, its firm reliance on environmental and climatic conditions makes it difficult for researchers to conduct experiments at the operational temperature (T) and Solar insolation level (G). These solar PV panels with a controllable light source are inefficient, unreliable, and unsuitable for testing PV algorithms such as Maximum Power Point Tracking …

Method Of Modeling The Swing Equation Using Time Synchronized Measurements, Robert Matthew Ferraro

Dissertations and Theses

In three phase, high-voltage transmission systems, synchronous generators accelerate or decelerate to adapt to changing power transfer requirements that occur during system disturbances. In network electrical power systems, frequency changes constantly based on system dynamics. Modeling network dynamics from oscillations and transients using time-synchronized measurements can provide real-time information, including angular displacements, voltage and current phasors, frequency changes, and rate of signal system decay from positive-sequence components.

Power system voltage and current waveforms are not steady-state sinusoids, especially during system disturbances. These waveforms contain sustained harmonic and non-harmonic components. Additionally, because of faults and other switching electromagnetic transients, there may …

Solar Photovoltaic Panels Utilization To Extract Clean And Green Energy For Utility Application Using Pvsyst Software: A Bibliometric Review, Anil Bhati, Mansi Srivastava, Nitesh Aggarwal, Hardik Singh, Javed Sayyad, Paresh Nasikkar

Library Philosophy and Practice (e-journal)

This paper presents a survey on educational documents in the field of solar photovoltaic (PV) utilization to extract clean and green energy. The main purpose of this bibliometric analysis is to understand the size of the available documents for the research of PV solar panel utilization using PVsyst. This detailed review was conducted in the PV research, literature considering all subjects from the Scopus database. The pattern for the specific arrangement of keywords was separated with the recovered results from the Scopus database, publication type, year of publication, distribution conveyance by nations, subject classes, association, authors, and financing organizations. It …

2050 Integrated Resource Plan For Public Services Company Of Colorado, Rehana Aziz, Josh Litwin

Master's Projects and Capstones

Our IRP aims to determine the optimal resource mix that will meet the forecasted load in 2030, 2040, and 2050. This report models a Reference or “business-as-usual” case and four alternative scenarios that deploy renewable energy resources or carbon capture technologies at varying levels to meet load at the beginning of each of these three decades. We assumed zero-carbon emissions targets for all four alternative scenarios, which go above and beyond Colorado’s current RPS. We are also retiring coal before 2040 for all four alternative scenarios in alignment with Xcel’s current plan.

The forecasted load in the Reference scenario is …

Smart E-Bike Conversion Kit And Helmet, Megan West, Marena Trujillo, Hossein Asghari

Honors Thesis

With many state governments across the United States implementing shutdowns to prevent the spread of COVID-19, many bike retailers have seen dramatic increases in bike sales. Electric bicycles (e-bikes) have become increasingly popular as the public searches for alternatives to public transportation. Unfortunately, e-bike users assume some risk by riding bikes that are faster than conventional bicycles. While kits to convert conventional bicycles to e-bikes exist, no “smart” e-bike/helmet kit specifically designed to keep the user safe is currently available on the market. To mitigate risks, a smart e-bike conversion kit with multiple novel safety features, including auditory and visual …

Evaluating The Thermal Conductivity Of Potting Materials Using The Hot-Wire Method, Yeny Hau Chen

Electrical Engineering Undergraduate Honors Theses

This thesis is focused on the evaluation of the thermal conductivity of certain potting materials, in particular Aluminum Nitride (AlN), thermal putty, and silicone oil using the “hot-wire” method in order to allow volume reductions of inductors, and thus, increase the power density of converters. The main objective of this thesis is then to study the behavior of these specific materials intended for high-density power converters by mixing them with different proportions and placing the resulting compounds into a can for calculating their thermal conductivities, in order to evaluate the effects on the power density of inductor-based converters. One objective …

Design And Fabrication Of A Microstrip Bandpass Filter In Ltcc, Allison Rucker

Electrical Engineering Undergraduate Honors Theses

The goal of the project was to design and fabricate a bandpass filter with a center frequency of 25GHz with a 2GHz bandwidth. The first step was to do the calculation to design a bandpass filter to meet these specifications along with the properties of the Dupont^TM GreenTape^TM 9K7. HFSS was then used to verify the results from the initial calculations. There was a significant error between the two results, so more tweaking was done to the calculations to get a better center frequency. After a final design was decided, the fabrication process started. Low-Temperature Co-Fired Ceramics (LLTC) …

Data Forgery Detection In Automatic Generation Control: Exploration Of Automated Parameter Generation And Low-Rate Attacks, Yatish R. Dubasi

Computer Science and Computer Engineering Undergraduate Honors Theses

Automatic Generation Control (AGC) is a key control system utilized in electric power systems. AGC uses frequency and tie-line power flow measurements to determine the Area Control Error (ACE). ACE is then used by the AGC to adjust power generation and maintain an acceptable power system frequency. Attackers might inject false frequency and/or tie-line power flow measurements to mislead AGC into falsely adjusting power generation, which can harm power system operations. Various data forgery detection models are studied in this thesis. First, to make the use of predictive detection models easier for users, we propose a method for automated generation …