Electromagnetics and Photonics Commons^™

System Efficient Esd Design Concept For Soft Failures, Giorgi Maghlakelidze

Doctoral Dissertations

"This research covers the topic of developing a systematic methodology of studying electrostatic discharge (ESD)-induced soft failures. ESD-induced soft failures (SF) are non-destructive disruptions of the functionality of an electronic system. The soft failure robustness of a USB3 Gen 1 interface is investigated, modeled, and improved. The injection is performed directly using transmission line pulser (TLP) with varying: pulse width, amplitude, polarity. Characterization provides data for failure thresholds and a SPICE circuit model that describes the transient voltage and current at the victim. Using the injected current, the likelihood of a SF is predicted. ESD protection by transient voltage suppressor …

Evolution Of Two-Element Directive Antennas, Tyler J. Mcpherson

College of Graduate Studies: Theses & Dissertations

The classic Yagi antenna is often utilized to provide directional radiation. Many facets of the Yagi antenna can be improved. This thesis focuses on the evolution of the two-element directive antennas, such as the Yagi antenna, in three ways. First, the inter-element spacing is reduced beyond those previously mentioned in literature. Next, an electrically-small version of the two-element Yagi with extremely close inter-element spacing is explored with a linear polarized and a circularly polarized configuration. Finally, further analysis of a wideband, circularly polarized, two-element, directive antenna with standard interelement spacing is performed.

Effect Of Layer Thickness On Structural, Morphological And Superconducting Properties Of Nb3Sn Films Fabricated By Multilayer Sequential Sputtering, M. N. Sayeed, U. Pudasaini, C. E. Reece, G. V. Eremeev, H. E. Elsayed-Ali

Electrical & Computer Engineering Faculty Publications

Superconducting Nb₃Sn films can be synthesized by controlling the atomic concentration of Sn. Multilayer sequential sputtering of Nb and Sn thin films followed by high temperature annealing is considered as a method to fabricate Nb₃Sn films, where the Sn composition of the deposited films can be controlled by the thickness of alternating Nb and Sn layers. We report on the structural, morphological and superconducting properties of Nb₃Sn films fabricated by multilayer sequential sputtering of Nb and Sn films on sapphire substrates followed by annealing at 950 °C for 3 h. We have investigated the …

Optical Spectroscopy And Theoretical Modelling Of Carrier Dynamics In Group-Iv Alloy Quantum Dots, Rahnuma Rahman

Theses and Dissertations

In recent years, Ge_1−xSn_x alloy quantum dots (QDs) have attracted significant interest due to their potential applications in photodetectors and light emitting devices in visible to mid IR spectral range and compatibility with silicon based platforms. While bulk Ge is an indirect bandgap semiconductor (0.66 eV), direct transitions can be made possible by incorporation of α-Sn at concentrations of ~10%, which however lowers the bandgap. Utilizing quantum confinement by reducing the size to below the Bohr radius also promotes direct transitions and more importantly increases the fundamental transition energies in GeSn alloy QDs, making them suitable for …

Sparsity Constrained Regression For High-Speed Signal Integrity Modeling, Jiacheng Zhuo, Jiayi He, Zurab Kiguradze, Bhyrav Mutnury, James Drewniak

Electrical and Computer Engineering Faculty Research & Creative Works

High-speed signal integrity (SI) modeling usually involves modeling non-linear subsystems. Traditional approaches like response surface modeling (RSM), artificial neural networks (ANN) and support vector machine (SVM) suffer from two major issues. Either they don't scale well when the number of dimensions or variables increase in the non-linear model, or they are sensitive to the initial training data used to create the models. For example: RSM approach requires large design of experiments (DoE) when the number of variables increase. With ANN, the designer has to spend a lot of time tuning or optimizing the hyperparameters. In this paper, a new approach …

Interfacial Contact With Noble Metal - Noble Metal And Noble Metal - 2d Semiconductor Nanostructures Enhance Optical Activity, Ricardo Raphael Lopez Romo

Graduate Theses and Dissertations

Noble metal nanoparticles and two-dimensional (2D) transition metal dichalcogenide (TMD) crystals offer unique optical and electronic properties that include strong exciton binding, spin-orbital coupling, and localized surface plasmon resonance. Controlling these properties at high spatiotemporal resolution can support emerging optoelectronic coupling and enhanced optical features. Excitation dynamics of these optical properties on physicochemically bonded mono- and few-layer TMD crystals with metal nanocrystals and two overlapping spherical metal nanocrystals were examined by concurrently (i) DDA simulations and (ii) far-field optical transmission UV-vis spectroscopic measurements. Initially, a novel and scalable method to unsettle van der Waals bonds in bulk TMDs to prepare …

High Frequency Ltcc Based Planar Transformer, Adithya Venkatanarayanan

Graduate Theses and Dissertations

As we move towards high power and higher frequency related technology, conventional wire-wound magnetics have their own limitations which has led path to the development of planar based magnetic materials. Nowadays more planar magnetic technology has been employed because it is easier to fabricate them. The planar magnetic is a transformer or an inductor that replaces the wire-wound transformer or inductors which generally uses copper wires. One of the main reasons why we move to planar magnetic technology is its operation at higher frequency which provides higher power density. This study explains in detail about the design and fabrication of …

Exploring Convergence Of Snake Skin-Inspired Texture Designs And Additive Manufacturing For Mechanical Traction, Catherine Sue Tiner

Graduate Theses and Dissertations

This research focuses on the understanding, development, and additive manufacture of a 3D printed snake skin-inspired texture pattern. The design functionalities of snake skin were determined through the study of the snake species Python Regius otherwise known as the ball python. Each scale of a snake has hierarchical texture with hexagonal macro-patterns aligned on the ventral surface of the skin with overriding anisotropic micro textured patterns such as denticulations and fibrils. Using a laser-powder bed fusion (L-PBF) process, 420 stainless steel samples were 3D printed which closely resemble the above described directional texture of natural snake skin. This printed surface …

Performance Enhancement And Characterization Of An Electromagnetic Railgun, Paul M. Gilles

Master's Theses

Collision with orbital debris poses a serious threat to spacecraft and astronauts. Hypervelocity impacts resulting from collisions mean that objects with a mass less than 1g can cause mission-ending damage to spacecraft. A means of shielding spacecraft against collisions is necessary. A means of testing candidate shielding methods for their efficacy in mitigating hypervelocity impacts is therefore also necessary. Cal Poly’s Electromagnetic Railgun was designed with the goal of creating a laboratory system capable of simulating hypervelocity (≥ 3 km/s) impacts. Due to several factors, the system was not previously capable of high-velocity (≥ 1 km/s) tests. A deficient projectile …

Bayesian Optimization For High-Speed Channel Equalization, Zurab Kiguradze, Nana Dikhaminjia, Mikheil Tsiklauri, Jiayi He, Bhyrav Mutnury, Arun Chada, James Drewniak

Electrical and Computer Engineering Faculty Research & Creative Works

Equalization methods are used to recover the signal attenuated by channel loss. Different optimization algorithms are applied to find the best tap coefficients for each equalization that will improve eye opening and reduce bit error rate. The goal function for most equalization optimization algorithms is to reduce the difference between input and output signals, which is a linear optimization problem and can be solved relatively easily. This indirectly will increase eye height and improve eye diagram. Directly optimizing eye height is a non-linear problem and cannot be solved with analytical method. We are proposing FFE and DFE combined equalization optimization …

Synthesis Of Cellulose Nanocrystal-Gold Nanoparticle Hybrid System For Surface Plasmon-Enhanced Property, Mahshid Iraniparast

Graduate Theses and Dissertations

Gold nanoparticles (AuNPs) have been brought to the forefront of various applications, ranging from theranostics, to organic photovoltaics, to biosensing owing to their localized surface plasmon resonance (LSPR) property. However, this property needs to be improved in order to allow for high sensitivity and quantitative detection of biomolecules. Hybrids of AuNPs with low-dielectric cellulose nanocrystal (CNCs) would yield enhancement of the LSPR property, which is driven by the confinement of electron oscillation at their interfaces. This study proposed a seed-mediated growth method to synthesize hybrids of CNCs-AuNPs. Sulfate groups on the surface of CNCs served as the sites for the …

Development Of A Comsol Microdialysis Model, Towards Creation Of Microdialysis On A Chip With Improved Geometries And Recovery, Patrick Pysz

Graduate Theses and Dissertations

Microdialysis (µD) sampling is a diffusion-limited sampling method that has been widely used in different biomedical fields for greater than 35 years. Device calibration for in vivo studies is difficult for current non-steady state analytes of interest correlated with both inflammatory response and microbial signaling molecules (QS); which exist in low ng/mL to pg/mL with molecular weights over a wide range of 170 Da to 70 kDa. The primary performance metric, relative recovery (RR), relating the collected sample to the extracellular space concentration varies from 10% to 60% per analyte even under controlled bench-top conditions. Innovations in microdialysis device design …

Integrated Chirped-Grating Spectrometer-On-A-Chip, Shima Nezhadbadeh

Optical Science and Engineering ETDs

In this dissertation we demonstrate a new structure based on waveguide coupling atop a silicon wafer using a chirped grating to provide the dispersion that leads to a high-resolution, compact, fully integrable and CMOS-compatible spectrometer. Light is both analyzed and detected in a single, completely monolithic component which enables realizing a high-resolution portable spectrometer with an extremely compact footprint. The structure is comprised of a SiO₂/Si₃N₄/SiO₂ waveguide on top of a silicon wafer. Grating regions are fabricated on the top cladding of the waveguide. The input light is incident on a chirped grating …

The Challenges Of Low-Energy Secondary Electron Emission Measurement, Matthew J. Vincie

Theses and Dissertations

The phenomena known as secondary electron emission was discovered over a century ago. Yet it remains very difficult to model accurately due to the limited availability of reliable experimental data. With the growing use of computer simulations in hardware development, the need for accurate models has increased. This research focused on determining what factors may be causing measurement discrepancies and methods for increasing the accuracy of measurements. It was found that several assumptions are commonly invoked when these measurements are performed that may not always be consistent with reality. The violation of these assumptions leads to measurement bias that is …

Measurement Of Electron Density And Temperature From Laser-Induced Nitrogen Plasma At Elevated Pressure (1–6 Bar), Ashwin P. Rao, Mark Gragston, Anil K. Patnaik, Paul S. Hsu, Michael B. Shattan

Faculty Publications

Laser-induced plasmas experience Stark broadening and shifts of spectral lines carrying spectral signatures of plasma properties. In this paper, we report time-resolved Stark broadening measurements of a nitrogen triplet emission line at 1–6 bar ambient pressure in a pure nitrogen cell. Electron densities are calculated using the Stark broadening for different pressure conditions, which are shown to linearly increase with pressure. Additionally, using a Boltzmann fit for the triplet, the electron temperature is calculated and shown to decrease with increasing pressure. The rate of plasma cooling is observed to increase with pressure. The reported Stark broadening based plasma diagnostics in …

Unidirectional And Nonreciprocal Nanophotonic Devices Based On Graphene And Magneto-Optical Materials, Vahid Foroughi Nezhad

LSU Doctoral Dissertations

In this dissertation, we first introduce compact tunable spatial mode converters for graphene parallel plate (GPP) waveguides. The converters are reciprocal and based on spatial modulation of graphene’s conductivity. The wavelength of operation of the mode converters is tunable in the mid-infrared wavelength range by adjusting the chemical potential of a strip on one of the graphene layers of the GPP waveguides. We also introduce optical diodes for GPP waveguides based on a spatial mode converter and a coupler, which consists of a single layer of graphene placed in the middle between the two plates of two GPP waveguides. \par …

Nonlinearities And Carrier Dynamics In Refractory Plasmonic Tin Thin Films, Heather George, Jennifer Reed, Manuel R. Ferdinandus, Clayton Devault, Alexei Lagutchev, Augustine Urbas, Theodore B. Norris, Vladimir M. Shalaev, Alexandra Boltasseva, Nathaniel Kinsey

Faculty Publications

Titanium nitride is widely used in plasmonic applications, due to its robustness and optical properties which resemble those of gold. Despite this interest, the nonlinear properties have only recently begun to be investigated. In this work, beam deflection and non-degenerate femtosecond pump-probe spectroscopy (800 nm pump and 650 nm probe) were used to measure the real and imaginary transient nonlinear response of 30-nm-thick TiN films on sapphire and fused silica in the metallic region governed by Fermi-smearing nonlinearities. In contrast to other metals, it is found that TiN exhibits non-instantaneous positive refraction and reverse saturable absorption whose relaxation is dominated …

Discontinuous Galerkin Vs. Ie Method For Electromagnetic Scattering From Composite Metallic And Dielectric Structures, Y.-Y. Zhu, Q.-M. Cai, R. Zhang, X. Cao, Y.-W. Zhao, B. Gao, Jun Fan

Electrical and Computer Engineering Faculty Research & Creative Works

In this paper, an efficient volume surface integral equation (VSIE) method with nonconformal discretization is developed for the analysis of electromagnetic scattering from composite metallic and dielectric (CMD) structures. This VSIE scheme utilizes curved tetrahedral (triangular) elements for volume (surface) modeling and the associated CRWG (CSWG) basis functions for volume current (surface) current modeling. Further, a discontinuous Galerkin (DG) volume integral equation (VIE) method and a DG surface integral equation (SIE) approach are adopted for dielectric and metallic parts, respectively, which allow both conformal and nonconformal volume/surface discretization improving meshing flexibility considerably. Numerical results are provided to demonstrate the accuracy, …

Nondestructive Electromagnetic Characterization Of Perfect-Electric-Conductor-Backed Uniaxial Materials, Adam L. Brooks

Theses and Dissertations

As the use of anisotropic materials in electromagnetic applications continues to proliferate, it becomes increasingly important to develop non-destructive evaluation methods for those materials in their installed configuration. In many applications, these materials are permanently affixed onto conducting bodies to reduce unwanted reflections, making it impossible to collect S₂₁ or S₁₂ transmission measurements as used in many techniques based on the well-known Nicolson-Ross-Weir algorithm. It also makes it impractical to reorient the sample to collect orthogonal measurements aligned with the optical axes of the anisotropic material. The goal of this research is to develop a two-reflection coefficient measurement …

Targeted Germanium Ion Irradiation Of Aluminum Gallium Nitride/Gallium Nitride High Electron Mobility Transistors, Melanie E. Mace

Theses and Dissertations

Microscale beams of germanium ions were used to target different locations of aluminum galliumnitride/gallium nitride (AlGaN/GaN) high electron mobility transistors (HEMTs) to determine location dependent radiation effects. 1.7 MeV Ge ions were targeted at the gap between the gate and the drain to observe displacement damage effects while 47 MeV Ge ions were targeted at the gate to observe ionization damage effects. Electrical data was taken pre, during, and post irradiation. To separate transient from permanent degradation, the devices were characterized after a room temperature anneal for at least 30 days. Optical images were also analyzed pre and post irradiation. …

Near-Field Effects On Partially Coherent Light Scattered By An Aperture, Milo W. Hyde Iv, Michael J. Havrilla

Faculty Publications

We investigate how the near field affects partially coherent light scattered from an aperture in an opaque screen. Prior work on this subject has focused on the role of surface plasmons, and how they affect spatial coherence is well documented. Here, we consider other near-field effects that might impact spatial coherence. We do this by examining the statistics of the near-zone field scattered from an aperture in a perfect electric conductor plane—a structure that does not support surface plasmons. We derive the near-field statistics (in particular, cross-spectral density functions) by applying electromagnetic equivalence theorems and the Method of Moments. We …

Design And Analysis Of Modular Axial Flux Switched Reluctance Motor, Rochak Shiwakoti

LSU New Orleans Theses and Dissertations

This thesis presents a new modular structure of the axial flux Switched Reluctance Motor (SRM). The design consists of four stator disks with each adjacent disk rotated 30 degrees apart and four rotor disks connected to a common shaft. The proposed design aims to reduce the unwanted radial force, mitigate the torque ripple, and improve the efficiency. The modular structure distributes the radial force and torque strokes along the axial length of the motor, potentially damping the torque pulsation. In addition, the modular structure would deliver the rating power at a lower current level, reducing the overall ohmic loss. Moreover, …

Polarization Properties Of Airy And Ince-Gaussian Laser Beams, Sean Michael Nomoto

Graduate Theses and Dissertations

The description of polarization states of laser light as linear, circular polarization within the paraxial scalar wave approximation is adequate for most applications. However, this description falls short when considering laser light as an electromagnetic wave satisfying Maxwell's equations. An electric field with a constant unit vector for direction of the field and a space dependent complex scalar amplitude in the paraxial wave approximation does not satisfy Maxwell equations which, in general, requires all three Cartesian components of electric and magnetic fields associated for a nonzero laser beam to be nonzero.

Physical observation of passing a linearly polarized laser through …

Triple-Junction Solar Cells : In Parallel., Levi C Mays

Electronic Theses and Dissertations

This paper looks into the current inefficiency of solar cells and attempts a few alternative solar cell structures in order to provide a more effective source of renewable energy. Currently, multi-junction solar cells are being developed to capture the sun’s light more efficiently. One of the ideas in this paper is to add a window to see if the addition of such a layer into a junction will increase the voltage while maintaining nearly the same current output. Central to this paper is the rearranging of the conducting layers of the multi-junction cell so that the junctions can be connected …

Growth Of Indium Nitride Quantum Dots By Molecular Beam Epitaxy, Steven P. Minor

Graduate Theses and Dissertations

Over the last decade, the evolution of the global consciousness in response to decreasing environmental conditions from global warming and pollution has led to an outcry for finding new alternative/clean methods for harvesting energy and determining ways to minimize energy consumption. III-nitride materials are of interest for optoelectronic and electronic device applications such as high efficiency solar cells, solid state lighting (LEDs), and blue laser (Blu-ray Technology) applications. The wide range of direct band gaps covered by its alloys (0.7eV-6.2eV) best illustrates the versatility of III-nitride materials. This wide range has enabled applications extending from the ultraviolet to the near …

3d Plasmonic Design Approach For Efficient Transmissive Huygens Metasurfaces, Bryan M. Adomanis, D. Bruce Burckel, Michael A. Marciniak

Faculty Publications

In this paper we present a design concept for 3D plasmonic scatterers as high- efficiency transmissive metasurface (MS) building blocks. A genetic algorithm (GA) routine partitions the faces of the walls inside an open cavity into a M x N grid of voxels which can be either covered with metal or left bare, and optimizes the distribution of metal coverage needed to generate electric and magnetic modes of equal strength with a targeted phase delay (Φt) at the design wavelength. Even though the electric and magnetic modes can be more complicated than typical low order modes, with their spectral overlap …

M2 Factor Of A Vector Schell-Model Beam, Milo W. Hyde Iv, Mark F. Spencer

Faculty Publications

Extending existing scalar Schell-model source work, we derive the M² factor for a general electromagnetic or vector Schell-model source to assess beam quality. In particular, we compute the M² factors for two vector Schell-model sources found in the literature. We then describe how to synthesize vector Schell-model beams in terms of specified, desired M² and present Monte Carlo simulation results to validate our analysis.

The Design Of Passive Networks With Full-Wave Component Models, Eric Valentino

USF Tampa Graduate Theses and Dissertations

In this thesis, the design of passive networks with the aid of full-wave simulation software and geometry-based models of lumped elements is investigated. This is done by examining the results of a number of simulation examples, as well as measured data from manufactured designs to compare against simulated equivalents. One such example is a chip antenna evaluation board design, in which the PCB, antenna, matching components and connector are all modeled. When measured, the simulation agreed with the board’s best matched frequency of 5.5 GHz to within 20 MHz. In another, a new antenna layout is generated from an existing …

Dc-Dc Converter For Electric Vehicle, Jason Y. Zhou, Nicholas James Mah

Electrical Engineering

In this work, a DC-DC converter is designed for an electric vehicle. The DC-DC converter is designed to provide 500W with a 200-400V input and a 12-15V adjustable output. Electric vehicle sales are beginning to increase in popularity and the need for DC-DC converters to siphon power from the tractive system is not yet fully satisfied, especially for single-seater class vehicles. Additionally, improving performance in efficiency without sacrificing wide input voltage range can benefit future DC-DC converter designs. In the end, a forward active clamp DC-DC converter is designed and tested. Additionally, spreadsheet calculators, LTSpice simulations, and Matlab scripts were …

Designing A Simulator For An Electrically-Pumped Organic Laser Diode, Robert Hulbert

Master's Theses

Organic semiconductors provide an alternative set of basis materials to fabricate electronic devices like PN Junctions, LEDs, and FETs. These materials have several benefits over traditional inorganic semiconductors including their mechanical flexibility, reliance on renewable resources, and inexpensive large-scale manufacturability. Despite the contemporary device implementations with organic semiconductors, a solid-state electrically-pumped organic laser diode does not exist. However, organically-based lasers do exist by utilizing the organic material strictly for optical gain. The challenge occurs when charge carriers appear in the organic material. The charge carriers must reach a concentration such that population inversion occurs producing optical gain. However, between the …