Open Access. Powered by Scholars. Published by Universities.®

Electromagnetics and Photonics Commons™

Open Access. Powered by Scholars. Published by Universities.®

Articles 1 - 20 of 20

Full-Text Articles in Electromagnetics and Photonics

Alford Loop Antennas For Ultra-High Energy Neutrino Detection, John K. Kimura Jun 2026

Alford Loop Antennas For Ultra-High Energy Neutrino Detection, John K. Kimura

Master's Theses

The neutrino is a fundamental particle of matter emitted by high energy phenomena, such as supernovae and black holes. Detecting neutrinos can give scientists information regarding the frequency of high-energy cosmic events, as well as point them towards specific high-energy events. Ultra-high energy (UHE) neutrino interactions in Greenland ice result in electromagnetic pulses between 200MHz and 800MHz. The Radio Neutrino Observatory - Greenland (RNO-G) seeks to observe the resultant electromagnetic waves. The Alford Loop antenna is proposed to detect these emissions, because of its dipole-like radiation pattern, horizontal polarization, and adequate dimensions to fit in a 10" diameter ice borehole. …


Design Of Experiment Analysis On Multiple Pim Sources In An Rf Antenna System, Shengxuan Xia, Yuchu He, Haicheng Zhou, Hanfeng Wang, Chulsoon Hwang Jan 2024

Design Of Experiment Analysis On Multiple Pim Sources In An Rf Antenna System, Shengxuan Xia, Yuchu He, Haicheng Zhou, Hanfeng Wang, Chulsoon Hwang

Electrical and Computer Engineering Faculty Research & Creative Works

Passive intermodulation (PIM) has been identified as one of the common root causes for receiving sensitivity degradation (desense) on radiofrequency (RF) antennas working in frequency-division duplex mode. The component-level PIM characterization and simulation have been well-established over the years. However, the study has been using an ideal 50 Ω transmission line system while antenna modules are more complicated than a simple transmission line structure. Moreover, the metallic contacts can exist in multiple locations with different connection topologies in real applications. This paper provides a method to simulate the PIM performance caused by the metallic contacts in a practical environment. In …


Fabrication And Measurement Of Lt-Gaas Photoconductive Antennas And Arrays, Zachary Paul Uttley Aug 2023

Fabrication And Measurement Of Lt-Gaas Photoconductive Antennas And Arrays, Zachary Paul Uttley

Graduate Theses and Dissertations

This thesis presents the fabrication and measurement of LT-GaAs based terahertz (THz) photo conductive antennas (PCAs) and arrays. The LT-GaAs THz PCAs are fabricated to serve as reference devices to new 2D material black phosphorous (BP) based THz PCAs. The LT-GaAs and BP devices have identical metallic electrodes, allowing for a comparison of emitted THz intensity and bandwidth. All PCAs have been measured using an open bench pulsed time-domain spectroscopy (TDS) system with a usable bandwidth from 0.1-4 THz, pumped with a 780nm Ti:Sapphire femtosecond laser. The results have shown LT-GaAs devices outperforming BP devices in signal amplitude and bandwidth …


Study And Design Of Array And Beamsteering Antennas For Millimeter Wave Band Application, Saeideh Shad Aug 2021

Study And Design Of Array And Beamsteering Antennas For Millimeter Wave Band Application, Saeideh Shad

Boise State University Theses and Dissertations

Millimeter wave (mmWave) communication systems have attracted significant interest regarding supporting high data rate of Gigabit/s communications for the new generation of wireless communication networks. MmWave communication systems have frequency ranges in between 30 and 300 GHz wherein an enormous amount of unused bandwidth is available. Although the available bandwidth of mmWave frequencies is promising for high data rate communications, the propagation characteristics of mmWave frequencies are significantly different from microwave frequency band in terms of path loss, diffraction and blockage, and atmospheric absorption. In general, the overall losses of mmWave signals are significantly larger than that of microwave signals …


Ultra-High-Energy Neutrino Detection Antenna Simulations, Nicholas C. Garcia Jun 2021

Ultra-High-Energy Neutrino Detection Antenna Simulations, Nicholas C. Garcia

Electrical Engineering

Neutrinos allow researchers to investigate high-energy galactic phenomena, such as supernovae and black holes. Neutrinos interact with their surroundings via the weak nuclear force and therefore, travel unattenuated through space and are not deflected by electromagnetic fields. However, they do rarely interact with other particles. When neutrinos interact with nucleons (protons or neutrons) in a dielectric medium (i.e.: ice sheets), they are detectable through a cone of coherent electromagnetic radiation (Askaryan Radiation) created by the particle shower generated from the neutrino interaction [1]. The Radio Neutrino Observatory in Greenland (RNO-G) detects UHE neutrinos greater than 100 PeV (1015 eV) …


A Reconfigurable Stretchable Liquid Metal Antenna, Phase Shifter, And Array For Wideband Applications, David M. Hensley Apr 2021

A Reconfigurable Stretchable Liquid Metal Antenna, Phase Shifter, And Array For Wideband Applications, David M. Hensley

Electrical and Computer Engineering ETDs

While liquid metals, such as mercury, have been used in electronics for quite some time, the non-toxic gallium based liquid metals have caused an increase in research for liquid metal applications. Some of the potential applications that have been previously presented range from reconfigurable antennas, strain and pressure sensors, and speakers and microphones to name a few. The focus of this work is to provide further research into the use of gallium based liquid metals as a reconfigurable antenna, a phase shifter, and an array. This is done by designing, constructing, and characterizing each of these reconfigurable liquid metal (LM) …


Mimo Antenna For Fifth Generation Mm-Wave Applications: A Bibliometric Survey, Rajeshwari R. Malekar, Laxmikant K. Shevada, Hema D. Raut, Amruta S. Dixit, Sumit Kumar Dec 2020

Mimo Antenna For Fifth Generation Mm-Wave Applications: A Bibliometric Survey, Rajeshwari R. Malekar, Laxmikant K. Shevada, Hema D. Raut, Amruta S. Dixit, Sumit Kumar

Library Philosophy and Practice (e-journal)

Nowadays most discussed technology is mm-wave and 5G communication. The requirement of 5G technology is high bandwidth, high data rate, and low latency. To fulfil these requirements for the current growth in mobile communication multiple input multiple output antenna is used. This bibliometric paper throws light on the various methods used to improve mutual coupling between multiple antennas. Various mutual coupling reduction techniques that are used in MIMO antennas like Dielectric resonator antenna, Electromagnetic Bandgap Structure, Neutralization lines, Defected Ground Structures, Metamaterial, etc. are explained. Scopus database is used for this bibliometric review on mm-wave MIMO 5G technology from the …


A Bibliometric Survey On Ultra Wideband Multiple Input Multiple Output Antenna With Improved Isolation, Laxmikant K. Shevada, Hema D. Raut, Rajeshwari R. Malekar, Amruta S. Dixit, Sumit Kumar Dec 2020

A Bibliometric Survey On Ultra Wideband Multiple Input Multiple Output Antenna With Improved Isolation, Laxmikant K. Shevada, Hema D. Raut, Rajeshwari R. Malekar, Amruta S. Dixit, Sumit Kumar

Library Philosophy and Practice (e-journal)

Ultra wideband (UWB) technology remains a viable choice for very high speed data communication in future applications involving large bandwidth. For boosting the data communication efficiency and to mitigate the multipath fading issue faced by UWB system with existing narrowband systems, Multiple Input Multiple Output (MIMO) antenna system is used along with UWB. Mutual coupling which must be smaller in value plays a vital role in deciding the efficiency of MIMO antenna and hence it becomes as important aspect. The mutual coupling reduction techniques of various UWB MIMO antennas are surveyed in this bibliometric paper. The bibliometric survey aims to …


Antenna Radiation Element Designs For 5g Applications, Zhijun Gui Dec 2020

Antenna Radiation Element Designs For 5g Applications, Zhijun Gui

Electrical Engineering Undergraduate Honors Theses

This thesis introduced the advantage of the fifth-generation network and gave examples to the three major classes of applications categorized by International Telecommunication Union-Radiocommunication Sector. In this work, a patch antenna and a board-band bow-tie antenna with microelectromechanical switch design were modified to meet 5G communication purposes. The revised patch antenna produced a minimum S11 of -57.92dB, a resonant frequency at the 28GHz, and bandwidth of 4.55GHz. The modified design meets the requirements for wireless communication purposes. During the duplication process of the board-band bow-tie antenna design, multiple discrepancies were found, and the proposed results were not able to achieve. …


Neutrino Detection Antenna, Samuel D. Keechler Jun 2020

Neutrino Detection Antenna, Samuel D. Keechler

Electrical Engineering

Neutrinos carry valuable information about deep space events that researchers can utilize to study the early universe. Since the first neutrino was detected in 1956, it is a relatively new physics research topic. A new state-of-the-art research facility, the Radio Neutrino Observatory in Greenland (RNO-G), was developed to detect Ultra-High Energy (UHE) neutrinos, ones with energy greater than 100 PeV (1015 electronvolts). For reference, this amount of energy lifts an apple 5 cm, or drives a neutrino, a particle 1034 times smaller by mass, near the speed of light [1]. UHE neutrino events typically occur less than five times a …


A Narrow-Wall Complementary-Split-Ring Slotted Waveguide Antenna For High-Power-Microwave Applications, Xuyuan Pan Oct 2018

A Narrow-Wall Complementary-Split-Ring Slotted Waveguide Antenna For High-Power-Microwave Applications, Xuyuan Pan

Electrical and Computer Engineering ETDs

A narrow-band, rugged, complementary-split-ring (CSR) slotted waveguide antenna (SWA) with significant size reduction is presented. The antenna is to be vertically front mounted on a land vehicle, with a horizontally polarized fan-beam radiation pattern. The radiation characteristics of a CSR slot in the narrow-wall of a rectangular waveguide are studied for the first time in this work. Both simulation and experimental results show that the complementary-split-ring slot radiates a linearly polarized wave with a total efficiency and gain close to those of conventional longitudinal slots, while the proposed CSR slots have a maximal outer diameter of 0.23λ0, much …


Passive Self-Interference Suppression For Single Channel Full-Duplex Operation, Adam Narbudowicz, Giuseppe Ruvio, Max Ammann Jan 2018

Passive Self-Interference Suppression For Single Channel Full-Duplex Operation, Adam Narbudowicz, Giuseppe Ruvio, Max Ammann

Articles

Full duplex radios have become a topic of increased interest in the wireless communications community. As part of this development, many efforts were directed to passively decrease the self-interference level at the antenna outputs. However, in many proposed solutions transmission and reception occur through different propagation channels. This paper demonstrates and quantifies the negative impact of channel differentiation on pivotal applications of full-duplex radio, such as cognitive radio. Antenna designs used for self-interference suppression in full-duplex radio architectures are analyzed. In order to ensure that transmission and reception occur within the same propagation channel, the use of the envelope correlation …


Design, Fabrication And Measurement Of A Plasmonic Enhanced Terahertz Photoconductive Antenna, Nathan Matthias Burford Dec 2016

Design, Fabrication And Measurement Of A Plasmonic Enhanced Terahertz Photoconductive Antenna, Nathan Matthias Burford

Graduate Theses and Dissertations

Generation of broadband terahertz (THz) pulses from ultrafast photoconductive antennas (PCAs) is an attractive method for THz spectroscopy and imaging. This provides a wide frequency bandwidth (0.1-4 THz) as well as the straightforward recovery of both the magnitude and phase of the transmitted and/or reflected signals. The achieved output THz power is low, approximately a few microwatts. This is due to the poor conversion of the femtosecond laser used as the optical pump to useable current inside the antenna semiconducting material. The majority of THz power comes from the photocarriers generated within ~ 100 nm distance from the antenna electrodes. …


Dielectric Prism Antenna, Jose Antonio Avila Jan 2016

Dielectric Prism Antenna, Jose Antonio Avila

Open Access Theses & Dissertations

3D printing is revolutionizing the development and manufacturing of devices. Currently multi-material 3D printing, like metals plus dielectrics, is in the early stages and not very accessible. This work set out to develop an all-dielectric antenna that could be 3D printed with current widely accessible 3D printing technologies. The antenna developed is an all-dielectric ultra-thin antenna with a simple geometry. The antenna radiates by using total internal reflection and a circulating mode operating as a leaky whispering gallery mode. We are calling the antenna the dielectric prism antenna because it acts like an optical prism. The dielectric prism antenna was …


Experimental Performance Evaluation And Design Of Schemes For Passive Rfid Network, Shadi Ebrahimi-Asl Jan 2016

Experimental Performance Evaluation And Design Of Schemes For Passive Rfid Network, Shadi Ebrahimi-Asl

Doctoral Dissertations

"Passive Radio Frequency Identification (RFID) is a short range technology for transferring information. The main advantage of passive RFID systems over active communication systems is the battery-less operation at the client sides. However, there are two major challenges that limit the widespread adaptation of passive RFID systems: short communication range and low read rate in dense deployments. This dissertation addresses these issues by studying the root causes and develops solutions for them.

In this dissertation, understanding the backscattering behavior of antennas and also the mutual coupling interactions among them are found to be the root causes of the two above-mentioned …


Design And Analysis Of Circularly Polarized Electrically Small Antennas, Jesse R. Ludwig Jan 2014

Design And Analysis Of Circularly Polarized Electrically Small Antennas, Jesse R. Ludwig

College of Graduate Studies: Theses & Dissertations

A growing need for efficient wireless communication is prevalent in the world in which we live. From cell phones to television to GPS applications, wireless communications are vital in consumer electronics and military applications. In these applications, a miniaturized antenna is sometimes necessary for reducing overall size of the communication system. For many satellite based communication applications, circular polarization in antennas is needed for efficient communication. In this thesis, the miniaturization technique known as T-top loading is utilized on two novel antenna designs. One design is an electrically small, circularly polarized planar cross dipole and the other design is a …


Antenna Designs For Wireless Medical Implants., Conor P. Conran Jan 2013

Antenna Designs For Wireless Medical Implants., Conor P. Conran

Masters

Active medical implants are devices that are surgically implanted inside the body. They have been developed to treat a wide range of ailments and many require some form of communications link with the outside world for maintenance and for remote medical diagnostics. Radio links promise a wide range of benefits over the traditional low frequency inductive coupling method.

Body tissue is a challenging environment, both for the device and for the radio signal that it transmits. Innovation in medical technology is creating a demand for high bandwidth links, and this in turn is driving the development of implantable antennas.

Many …


Infrared Tapered Slot Antennas Coupled To Tunnel Diodes, Louis A. Florence Jan 2012

Infrared Tapered Slot Antennas Coupled To Tunnel Diodes, Louis A. Florence

Electronic Theses and Dissertations

Tapered slot antennas (TSAs) have seen considerable application in the millimeter-wave portion of the spectrum. Desirable characteristics of TSAs include symmetric E- and H-plane antenna patterns, and broad non-resonant bandwidths. We investigate extension of TSA operation toward higher frequencies in the thermal infrared (IR), using a metal-oxide-metal diode as the detector. Several different infrared TSA design forms are fabricated using electronbeam lithography and specially developed thin-film processes. The angular antenna patterns of TSA-coupled diodes are measured at 10.6 micrometer wavelength in both E- and H-planes, and are compared to results of finite-element electromagnetic modeling using Ansoft HFSS. Parameter studies are …


Aperture Coupled Microstrip Antenna Design And Analysis, Michael Paul Civerolo Jun 2010

Aperture Coupled Microstrip Antenna Design And Analysis, Michael Paul Civerolo

Master's Theses

A linearly-polarized aperture coupled patch antenna design is characterized and optimized using HFSS antenna simulation software. This thesis focuses on the aperture coupled patch antenna due to the lack of fabrication and tuning documentation for the design of this antenna and its usefulness in arrays and orthogonally polarized communications. The goal of this thesis is to explore dimension effects on aperture coupled antenna performance, to develop a design and tuning procedure, and to describe performance effects through electromagnetic principles.

Antenna parameters examined in this study include the dimensions and locations of the substrates, feed line, ground plane coupling slot, and …


Liquid Crystal Optics For Communications, Signal Processing And 3-D Microscopic Imaging, Sajjad Khan Jan 2005

Liquid Crystal Optics For Communications, Signal Processing And 3-D Microscopic Imaging, Sajjad Khan

Electronic Theses and Dissertations

This dissertation proposes, studies and experimentally demonstrates novel liquid crystal (LC) optics to solve challenging problems in RF and photonic signal processing, freespace and fiber optic communications and microscopic imaging. These include free-space optical scanners for military and optical wireless applications, variable fiber-optic attenuators for optical communications, photonic control techniques for phased array antennas and radar, and 3-D microscopic imaging. At the heart of the applications demonstrated in this thesis are LC devices that are non-pixelated and can be controlled either electrically or optically. Instead of the typical pixel-by-pixel control as is custom in LC devices, the phase profile across …