Electromagnetics and Photonics Commons^™

Development Of Mems-Based Corrosion Sensor, Feng Pan

Graduate Theses and Dissertations

This research is to develop a MEMS-based corrosion sensor, which is used for monitoring uniform, galvanic corrosion occurring in infrastructures such as buildings, bridges. The corrosion sensor is made up of the composite of micro/nano metal particles with elastomers. The mechanism of corrosion sensor is based on the mass transport of corrosive species through the sensor matrix. When the metal particles in the matrix corrode, the electrical resistivity of the material increases due to increasing particle resistances or reduction of conducting pathways. The corrosion rate can be monitored by detecting the resistivity change in sensing elements. The life span of …

Conductive Concrete For Electromagnetic Shielding – Methods For Development And Evaluation, Aaron P. Krause

Department of Computer Electronics and Engineering: Dissertations, Theses, and Student Research

This research investigates the development and evaluation innovative methods for the use of conductive concrete as an electromagnetic shield. New testing methods are developed to determine the best conductive components to use in the design of a concrete mixture for shielding that shows the best promise. The conductive concrete mixture has the potential to provide electromagnetic shielding that is cost-effective in terms of construction, operation, and maintenance compared to conventional approaches. Two testing methods, Small Sample Testing and Large Slab Testing, are developed based on standardized testing methods that have been modified for the testing of conductive concrete mixtures. As …

Energy Harvesting Of Human Kinetic Movement, David Marusiak, Julia Carrillo

Electrical Engineering

Development of kinetic energy scavenging applications from the human body necessitates additional research to assist in designating a mounting position for a potential device. A data acquisition system adequately provides a parametric average power comparison among four locations on the body (waist, upper arm, hand, and calf) for both a male and female subject. Experimentally, the hand-held device provided the highest average power. Thus, subsequent investigation at set speeds provides further analysis of the output’s characteristically linear behavior. The physical energy-harvesting device features a plastic tube casing wrapped with the stationary coiled wire through which a neodymium magnet oscillates. While …

Optimization Of Nonlinear Switch Cells For Switching Converters, Bradley Alan Reese

Graduate Theses and Dissertations

Switch cells consist of an array of power switches and passive components which can replace the main switches alone in many power topologies, allowing reduced switching loss without altering the power topology directly. This thesis discusses the development of a switch cell topology that utilizes a saturable resonant inductor to reduce the size and power loss of the cell. Additionally, the cell transfers energy stored in the inductor into a capacitor for efficient energy storage during the cell's conduction region. This energy is then transferred back to the system when the cell turns off, thus reducing the total switching energy.

Plasmonic And Photonic Designs For Light Trapping In Thin Film Solar Cells, Liming Ji

Graduate Theses and Dissertations

Thin film solar cells are promising to realize cheap solar energy. Compared to conventional wafer cells, they can reduce the use of semiconductor material by 90%. The efficiency of thin film solar cells, however, is limited due to insufficient light absorption. Sufficient light absorption at the bandgap of semiconductor requires a light path more than 10x the thickness of the semiconductor. Advanced designs for light trapping are necessary for solar cells to absorb sufficient light within a limited volume of semiconductor. The goal is to convert the incident light into a trapped mode in the semiconductor layer.

In this dissertation, …

Fiber-Tip Fabry–Perot Interferometric Sensor Based On A Thin Silver Film, Fawen Guo

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

Fiber-optic sensors have many advantages, including small size, light weight, immunity to electromagnetic interference, and the capability of remote sensing. Fiber- tip sensors are fabricated on a fiber tip and are the smallest type of fiber-optic sensor. The fiber-tip sensors have attracted a great deal of attention in past years for pressure, temperature, and acoustic sensing.

In this thesis, a fiber-tip sensor based on an ultra-thin silver film was proposed and demonstrated for highly sensitive and high frequency ultrasonic detection. The film is prepared by the vacuum thermal deposition method and then transferred to the fiber tip. The sensor has …

Configuration Studies Of Electrostatic And Magnetostatic Active Space Radiation Shielding, Trac K. Nguyen

Electrical & Computer Engineering Theses & Dissertations

Developing successful and optimal solutions for mitigating the hazards of radiation in deep space is critical for the success of deep-space long duration explorations, including mission to the Moon, Mars and beyond. A recent report (Tripathi et al., 2008) had explored the feasibility of using electrostatic shielding in conjunction with state-of-the-art materials shielding technologies.

In this thesis research, we study the active electrostatic shielding strategy and examine a hybrid configuration that utilizes both electrostatic and magnetostatic fields. The main advantages of this system are shown to be: (i) much lower magnetic fields that could be below the thresholds set for …

Degenerate Parallel Conducting Layer And Conductivity Type Conversion Observed From P-Ge1 - YSnY (Y = 0.06%) Grown On N-Si Substrate, Mee-Yi Ryu, Yung Kee Yeo, M. Ahoujja, Thomas R. Harris, Richard T. Beeler, John Kouvetakis

Faculty Publications

Electrical properties of p-Ge_1−ySn_y (y = 0.06%) grown on n-Si substrate were investigated through temperature-dependent Hall-effect measurements. It was found that there exists a degenerate parallel conducting layer in Ge_1−ySn_y/Si and a second, deeper acceptor in addition to a shallow acceptor. This parallel conducting layer dominates the electrical properties of the Ge_1−ySn_y layer below 50 K and also significantly affects those properties at higher temperatures. Additionally, a conductivity type conversion from p to n was observed around 370 K for this sample. A two-layer conducting model was used …

Serpentine Low Loss Trapezoidal Silica Waveguides On Silicon, Xiaomin Zhang, Mark Harrison, Audrey Harker, Andrea M. Armani

Engineering Faculty Articles and Research

We report the fabrication and characterization of straight and serpentine low loss trapezoidal silica waveguides integrated on a silicon substrate. The waveguide channel was defined using a dual photo-lithography and buffered HF etching and isolated from the silicon substrate using an isotropic silicon etchant. The waveguide is air-clad and thus has a core-cladding effective index contrast of approximately 25%. Measured at 658, 980 and 1550nm, the propagation loss was found to be 0.69, 0.59, and 0.41dB/cm respectively, with a critical bending radius less than 375μm. The waveguide’s polarization behavior was investigated both theoretically and experimentally. Additionally, the output power shows …

Ground Vehicle Navigation Using Magnetic Field Variation, Jeremiah A. Shockley

Theses and Dissertations

The Earth's magnetic field has been the bedrock of navigation for centuries. The latest research highlights the uniqueness of magnetic field measurements based on position due to large scale variations as well as localized perturbations. These observable changes in the Earth's magnetic field as a function of position provide distinct information which can be used for navigation. This dissertation describes ground vehicle navigation exploiting variation in Earth's magnetic field using a self-contained navigation system consisting of only a magnetometer and magnetic field maps. In order to achieve navigation, effective calibration enables repeatable magnetic field measurements from different vehicles and facilitates …

Commissioning Of The Asta Laser Lab With Uv Pulse Length Characterization, Daniel Kelley, Jeff Corbett

STAR Program Research Presentations

The Linac Coherent Light Source (LCLS) at SLAC depends on a photocathode electron gun to provide the linear accelerator with the raw material – electrons – used for making X-ray laser pulses. The photocathode used in the LCLS Injector is a clean copper plate in high vacuum. When the cathode is struck with high energy UV light, electrons are liberated from its surface and then accelerated down the linac with radio-frequency electric fields. These fast-moving bunches of electrons are directed through an undulator magnet to radiate X-ray light.

Although scientists have been using photocathode techniques at SLAC for 25 years, …

3.5 To 30 Mhz Automatic Antenna Impedance Matching System, William Blodgett

Electrical Engineering

Two-way communications using 3 to 30 MHz, high-frequency (HF) radio, also known as shortwave radio, provides worldwide coverage with no infrastructure required between stations. Amateur or “Ham” radio operators apply this advantage to long distance communications and to provide disaster relief communications. Optimum frequencies for long distance propagation are time-of-day variant necessitating an operating frequency range of 3 to 30 MHz. HF half wave dipole antenna length varies from 15 to 150 ft over this range. Fixed-length antenna impedance varies with frequency due to physical dimension dependent capacitance and inductance. Maximum transmitter to antenna power transfer occurs when the transmission …

Spectral Analysis Of Encrypted Chaotic Signals Using Fast Fourier Transforms And Laboratory Spectral Analyzers, Monish Ranjan Chatterjee, Abhinay Kundur

Electrical and Computer Engineering Faculty Publications

The use of acousto-optic chaos, as manifested via first-order feedback in an acousto-optic Bragg cell, in encrypting a message wave and subsequently recovering the message in the receiver using a chaotic heterodyne strategy, has been reported recently [1-3]. In examining the dynamical system analytically using computer simulation, (expected) modulated chaos waveforms are obtained within specified observation windows.

Because of the relatively random nature inherent in chaos waveforms, it is essentially impossible to ascertain from the visual display of the chaotic wave whether a given message signal has in fact modulated the chaotic "carrier". In fact, it has been observed from …

Optical Mode Study Of Galium Nitride Based Laser Diodes, Douglas Cattarusa

Electrical Engineering

This paper focuses on the optical mode analysis of laser diodes to improve light emission. Under the mode analysis, we compare the optical confinement factor (OCF) percentage of the emitting light from the LDs. There are two structures which we analyze: a basic GaN waveguide structure and an InGaN waveguide structure. The second structure has additional InGaN waveguides and is analyzed under two additional design variations: the concentration of Indium and the thickness of the top waveguide layer. The results of this study indicate introducing InGaN waveguide layers correlates with lower order modes (zero and first order) and increase the …

Highly Sensitive X-Ray Detectors In The Low-Energy Range On N-Type 4h-Sic Epitaxial Layers, K. C. Mandal, P. G. Muzykov, J. R. Terry

Faculty Publications

No abstract provided.

Design, Fabrication, And Testing Of Flexible Inkjet-Printed Antennas, Yahiea M. H. Al-Naiemy

Theses and Dissertations

During the past four decades, microstrip antennas have attracted much attention due to their thin profile, ease of fabrication, low cost, and conformability. Inkjet-printing flexible antennas using highly conducting patterns can complement and extend the above-mentioned advantages to achieve modern, clean, fast, and reliable antenna fabrication technologies. Moreover, the use of nanoscale materials allows for the development of a new generation of modern printed circuit antennas. In this thesis, several microstrip antennas are presented with different geometries on both rigid and flexible substrates. The antennas were designed and simulated using two different 3D full-wave electromagnetic simulation tools: Ansoft's High Frequency …

Solar Light Bulb, David G. Guzman, Virgilio Gonzalez

COURI Symposium Abstracts, Summer 2012

The Solar Lighting project is a work driven towards building a low-cost and environmental-friendly solar bulb and to understanding the science behind its behavior. A solar light bulb refers to a device capable of absorbing and transferring solar energy to light up an enclosed area. By using the physical properties of fluids and light is possible to manipulate solar light waves to illuminate an enclosed structure. Moreover, this project attempts to utilize recycled materials that reduce the cost of such device, helping not only the planet but also the costumer’s pocket. The ultimate goal for this project is to scientifically …

Chalcogenide Microsphere Fabricated From Fiber Tapers Using Contact With A High-Temperature Ceramic Surface, Pengfei Wang, Ganapathy Murugan, Gilberto Bramilla, Ming Ding, Yuliya Semenova, Qiang Wu, Gerald Farrell

Articles

The fabrication 1 and characterization of a 2 chalcogenide glass microsphere resonator has been demonstrated. 3 At wavelengths near 1550 nm, whispering gallery mode 4 resonances can be efficiently excited in a 74-μm-diameter 5 chalcogenide glass microsphere via evanescent coupling using a 6 tapered silica glass fiber with a waist diameter of circa 2 μm. 7 Resonances with Q-factors greater than 105 were observed. 8 Due to the high nonlinearity properties of the chalcogenide 9 material and the ease of fabrication process, chalcogenide 10 microspheres offer the potential for robustly assembled fully 11 integrated photonic devices. 12 Index Terms—Chalcogenide

Modeling, Identification, Validation And Control Of A Hybrid Maglev Ball System, Ahmed Elhussein E. Mekky

Mechanical & Aerospace Engineering Theses & Dissertations

In this thesis, the electrodynamics of a single axis hybrid electromagnetic suspension Maglev system was modeled and validated by applying it to a single axis hybrid maglev ball experiment. By exploring its linearized model, it was shown that the single axis hybrid Maglev ball has inherently unstable dynamics. Three control scenarios were explored based on the linearized model; (1) Proportional, Deferential (PD) control, (2) Proportional, Deferential, Integral (PID) and (3) PID controller with pre-filtering. This thesis has shown that a PID controller with a pre-filtering technique can stabilize such a system and provide a well-controlled response.

A parametric system identification …

Application Of Chebyshev Formalism To Identify Nonlinear Magnetic Field Components In Beam Transport System, Michael Spata

Physics Theses & Dissertations

An experiment was conducted at Jefferson Lab's Continuous Electron Beam Accelerator Facility to develop a beam-based technique for characterizing the extent of the nonlinearity of the magnetic fields of a beam transport system. Horizontally and vertically oriented pairs of air-core kicker magnets were simultaneously driven at two different frequencies to provide a time-dependent transverse modulation of the beam orbit relative to the unperturbed reference orbit. Fourier decomposition of the position data at eight different points along the beamline was then used to measure the amplitude of these frequencies. For a purely linear transport system one expects to find solely the …

Reconfigurable Antenna And Rf Circuits Using Multi-Layer Stretchable Conductors, Riaz Ahmed -. Liyakath

USF Tampa Graduate Theses and Dissertations

The growth of flexible electronics industry has given rise to light-weight, flexible devices which have a wide range of applications such as wearable electronics, flexible sensors, conformal antennas, bio-medical applications, solar cells etc. Though several techniques exist to fabricate flexible devices, the limiting factors have been durability, cost and complexity of the approach. In this research, the focus has been on developing stretchable (flexible) conductors using a multi-layer structure of metal and conductive rubber. The stretchable conductors developed using this approach do not lose electrical connection when subjected to large strains up to 25%. Also, the conductivity of the conductive …

Novel Metamaterial Based Antennas For Flexible Wireless Systems, Haider Khaleel

Theses and Dissertations

Recent years have witnessed a great deal of interest from both academia and industry in the field of flexible electronic systems. This research topic tops the pyramid of research priorities requested by many national research agencies. Consistently, flexible electronic systems require the integration of flexible antennas operating in specific frequency bands to provide wireless connectivity which is highly demanded by today's information oriented society. On the other hand, metamaterials have become very popular in the design of contemporary antenna and microwave devices due to their wide range of applications derived from their unique properties which significantly enhances the performance of …

The Effect Of Polarization And Ingan Quantum Well Shape In Multiple Quantum Well Light Emitting Diode Heterostructures, Patrick M. Mcbride

Master's Theses

Previous research in InGaN/GaN light emitting diodes (LEDs) employing semi-classical drift-diffusion models has used reduced polarization constants without much physical explanantion. This paper investigates possible physical explanations for this effective polarization reduction in InGaN LEDs through the use of the simulation software SiLENSe. One major problem of current LED simulations is the assumption of perfectly discrete transitions between the quantum well (QW) and blocking layers when experiments have shown this to not be the case. The In concentration profile within InGaN multiple quantum well (MQW) devices shows much smoother and delayed transitions indicative of indium diffusion and drift during …

3d Electromagnetic Simulation Tool Exposure For Undergraduate Electrical Engineers: Incorporation Into An Analog Filters Course, Bobby B. Pheng

Master's Theses

With the growth of wireless communications, comes the need for engineers knowledgeable in 3D electromagnetic (EM) simulation of high-frequency circuits. To give electrical engineering students a better understanding of the behavior of electromagnetic fields, experiments including the use of 3D EM simulation software were proposed. Most students get lost in differential equations, curls, and divergences; this thesis aims to remedy that by exposing them to 3D EM simulation, which may motivate them toward further study in electromagnetics. Also, experience using EMPro is very beneficial for future RF/microwave/antenna engineers, as use of 3D EM simulation is becoming a requirement for this …

Pulsed Class-G Rf Amplifier System, Kevin Maulhardt, Kevin Haskett

Electrical Engineering

No abstract provided.

Day/Night Band Imager For A Cubesat, Eric Stanton

Electrical Engineering

Day/Night Band (DNB) earth sensing and meteorological systems like the Defense Meteorological Satellite Program (DMSP) Operational Linescan System (OLS) provide visible wavelength imagery 24 hours a day that is used primarily for cloud imaging in support of weather forecasting. This paper describes a compact push-broom imager that meets low light imaging requirements for DMSP OLS and the NOAA/NASA Joint Polar Satellite System (JPSS) as documented in the Integrated Operational Requirements Document [1] (IORD) including the imager design, system level concepts of operation for data collection, radiometric and spatial calibration, and data transmission to Earth. This small, lightweight imager complies with …

Inductive Metal Identification, Paul Maggi

Electrical Engineering

This project focuses on creating a device to differentiate between various types of metals via magnetic induction. Magnetic induction is used because it is both non-optical and non-contact. It achieves this by generating a varying magnetic field, which induces eddy currents in the metal. These eddy currents produce small disturbances in the surrounding magnetic field, which can be sensed with Hall Effect Sensors (HES). The primary challenge in this project was generating a sufficiently strong magnetic field to detectable disturbances. In order to achieve better results, a stronger magnetic field must be used as well as more sensitive Hall Effect …

Light Extraction Enhancement Of Gan Based Leds Using Top Gratings, Patterned Sapphire Substrates, And Reflective Surfaces, Greg Chavoor

Master's Theses

In the last 15 years, an immense amount of research has gone into developing high efficiency Gallium Nitride based light emitting diodes (LED). These devices have become increasingly popular in LED displays and solid state lighting. Due to the large difference in refractive index between GaN and Air, a significant amount of light reflects at the boundary and does not escape the device. This drawback decreases external quantum efficiency (EQE) by minimizing light extraction. Scientists and engineers continue to develop creative solutions to enhance light extraction. Some solutions include surface roughening, patterned sapphire substrates, and reflective layers.

This study proposes …

Design, Modeling And Fabrication Of Shear Mode Bulk Acoustic Wave Sensor As A Potential Biosensor, Chi-Jung Cheng

Dissertations

There has been an increasing interest in development of thin film bulk acoustic wave resonator (FBAR) devices for chemical and biological sensing applications in the environmental and biomedical industries. The zinc oxide (ZnO) thin film based FBAR devices provides attractive advantages, such as high resonant frequency, small size, and rapid response. Typically, the ZnO-based FBAR devices are operated in the longitudinal wave mode where the ZnO crystallites are perpendicular to the substrate. In gaseous environments, the longitudinal mode FBAR device provides high sensitivity for mass sensing. However, the longitudinal wave mode is adversely affected when used in liquid environments because …

A Linear Sampling Multiple Frequency Method For Target Detection, Tyler Bowman

Electrical Engineering Undergraduate Honors Theses

In the field of inverse scattering problems of electromagnetic imaging, there are many techniques that can be used to detect unknown objects. Generally these methods maintain a direct relationship between the precision of the target shape and the amount of time required to obtain the solution. However, it has been shown that hybridization, or a combination of techniques, can be used to obtain the shape reconstruction that is accurate and less expensive computationally. Previous research in the Computational Electromagnetics Group of Professor El-Shenawee at the University of Arkansas has looked into the use of hybridization by combining the Level Set …