Electromagnetics and Photonics Commons^™

Analysis And Design Of A 2-Bit Millimeter-Wave Reconfigurable Intelligent Surface And Investigation Of Fss-Assisted Angular Stability, Max Spalek

Master's Theses

Millimeter-Wave (mm-wave) technology utilizes high frequency spectrum and can deliver multi-gigabit speeds, ultra-low latency, and massive bandwidth capacity. However, this technology is rather new and many technical challenges remain. On the other hand, Reconfigurable Intelligent Surfaces (RIS) have emerged as promising structures for controllable electromagnetic wavefront manipulation in wireless communication systems. This thesis presents the design of a 2-bit RIS unit-cell element operating throughout the 30–34 GHz mm-wave band, where the structure was progressively refined from an initial resonating geometry toward a grounded reflective RIS configuration. The proposed structure utilizes PIN-diode switching states to produce four discrete reflected phase states …

Millimeter-Wave Antenna Gain Enhancement Through Stacked Planar Substrates, Zachary Bergstedt

Electrical and Computer Engineering ETDs

This work presents a new wideband millimeter-wave (mmWave) and sub-terahertz antenna design with flexible directivity through the integration of stepped horn antennas and transverse substrate integrated waveguide (SIW) slots for radar and communication applications. The work gives a theoretical and analytical basis for this filter-inspired approach to improving bandwidth and directivity, and presents design and results for a standalone stepped horn, a Ka-band antenna with a solid stepped horn and SIW feed, and W-band antennas with empty SIW feeds and stepped horns manufactured out of multiple planar layers. The realized antennas show bandwidth up to 40% and gain up to …

Designing Enhanced Nonlinearity In Plasmonic Devices With Epsilon-Near-Zero Films, Kevin Tran Le

Electrical Engineering and Computer Science (MS) Theses

The growing demand for energy-efficient optical information processing motivates compact nonlinear photonic devices that can operate at low power. Silicon photonics is a mature platform for linear optical functions, but nonlinear operation remains challenging because of its weak Kerr response, two-photon absorption at telecommunication wavelengths, and limited compatibility with deeply subwavelength plasmonic confinement. This thesis computationally investigates epsilon-near-zero thin films integrated into plasmonic waveguide architectures as a route toward stronger light–matter interaction in compact nonlinear devices.

Two waveguide geometries are examined: a hybrid metal-insulator-metal plasmonic slab waveguide incorporating an ultrathin indium tin oxide epsilon-near-zero layer (5–50 nm), and a dielectric-loaded …

Condition Monitoring Of Induction Motor Using Motor Current Signature Analysis, Francis Ikechukwu Obianke, Joseph Okhaifoh, Benjamin Akinloye

Al-Bahir

Induction machines serve as the cornerstone and driving force of modern manufacturing and production systems. This research aims to monitor and analyse the operating performance of induction motors using motor current signature analysis (MCSA). MCSA is employed to process the current signal of a motor into a frequency spectrum, known as the current signature by applying the Fast Fourier Transform (FFT) algorithm. The underlying principle is that vibration generated in a motor is closely related to the changes of the magnetic field density, and the induced voltage varies with the stator current.

A simulation model replicating the behaviour of an …

Design Of Energy-Efficient, Scalable, And Flexible Tensor Processing Architectures With Electro-Photonic Integrated Circuits, Oluwaseun Alo

Theses and Dissertations--Electrical and Computer Engineering

In recent years, artificial intelligence has achieved remarkable success across domains such as computer vision, natural language processing, and scientific computing. This progress has been driven largely by advances in deep learning, particularly deep neural networks (DNNs), including convolutional neural networks (CNNs) and transformer-based models. While these models deliver unprecedented accuracy, often surpassing human performance, their computational complexity continues to grow rapidly due to multibillion- and trillion-parameter designs. As model sizes and deployment scales expand, the demand for energy-efficient and high-throughput hardware accelerators has intensified. Conventional electronic platforms based on CPUs, GPUs, ASICs, and FPGAs are increasingly constrained by the …

Nanomagnet Based Reservoir Computing And Quantum Control, Fahim F. Chowdhury

Theses and Dissertations

Conventional CMOS scaling has driven remarkable advances in computing but faces increasing physical and energy constraints, motivating alternative computing paradigms that integrate memory and computation while improving energy efficiency. Nanoscale magnetic systems offer a promising platform for such approaches because their intrinsic nonlinear dynamics and localized magnetic fields can support both classical and quantum information processing. This thesis investigates nanomagnetic systems for physical reservoir computing and, with primary emphasis, for localized quantum control of spin qubits.

The first part explores dipole-coupled nanomagnet arrays as physical reservoirs. Micromagnetic simulations demonstrate nonlinear dynamical behavior with high short-term memory and parity-check capacity, enabling …

Exploratory Study Of Semiconductor Nanomembranes In Em Applications, Grant D. Heileman

Electrical and Computer Engineering ETDs

Antenna systems are a cornerstone of modern technologies, playing an increasingly vital role in their advancement. As demand for compact, high-performance, and adaptable communication platforms grows reconfigurable antenna technologies are becoming essential. This research explores a novel front-end reconfigurable antenna system (FERAS) architecture that leverages the mechanical flexibility and photoconductive behavior of semiconductor nanomembrane (SNM) devices. By exploiting the emergent properties of ultra-thin silicon (Si) or gallium arsenide (GaAs) nanomaterials and optically exciting these samples using vertical-cavity surface-emitting laser (VCSEL) arrays, this study develops lightweight, low-cost, deployable antenna structures for satellite communications, remote sensing, GPS, and radar. Despite their significant …

Design And Performance Analysis Of A Frequency-Reconfigurable Rectangular Patch Antenna With Dual-Slot Defected Ground Structure For Gsm Band, Sara Abdelbaset, Ashraf Khalaf, Amr Hussien, Ahmed A. Kabeel

Journal of Engineering Research

In this paper, an innovative frequency-tunable rectangular patch antenna is presented, featuring interlaced circular and U-shaped narrow slots, combined with a rectangular-shaped defected ground structure (DGS). This design is specifically developed to produce radiation patterns similar to those of traditional dipole antennas. The integration of the rectangular DGS with three RF varactor diodes, along with two equivalent microstrip conductors, enables a tunable operating frequency band that ranges from 1.08 GHz to 1.7 GHz, achieving a total bandwidth of 0.62 GHz. The DC biasing network connected to the three RF varactor diodes is utilized to finely tune and adjust the resonance …

A 0.18 Μm Cmos 40 Ghz Miniaturized Coupled-Line Coupler With Enhanced Directivity, Elsayed Ibrahim Elsaidy, Amr H. Hussein Prof.Dr., Mustafa M. Abd Elnaby Prof. Dr., Anwer S. Abd El-Hameed Dr.

Journal of Engineering Research

No abstract provided.

Photonic Crystal Devices For Chip Scale Sensing Systems, Yudong Chen

Electrical Engineering Dissertations - Archive

This thesis investigates the design and integration of photonic crystal (PC) structures for compact, high-performance optical platforms, with a focus on applications in gas sensing, on-chip lasers, and flat optics. Chapter 1 introduces the fundamental principles of PC design and simulation, highlighting their potential to replace bulky components in micro-gas chromatography (µGC) systems through miniaturization and integration. Chapter 2 explores PC-based nanobeam lasers, including the Lambda-Scale Embedded Active-Region Photonic Crystal (LEAP) laser, which demonstrates strong optical confinement and energy-efficient operation, with energy consumption as low as 8 fJ/bit. These laser designs are evaluated for their suitability in low-power, high-speed on-chip …

Enhancing Radiation Performance Of A 0.18 Μm Cmos 60 Ghz On-Chip Double-Slot Vivaldi Antenna, Elsayed Ibrahim Elsaidy Mr., Amr H. Hussein Prof.Dr., Mustafa M. Abd Elnaby Prof. Dr.

Journal of Engineering Research

This paper presents the design of a 60-GHz double-slot Vivaldi antenna (DSVA) using standard 0.18 µm CMOS technology. The antenna's two slots are uniformly excited in both amplitude and phase by a coplanar waveguide (CPW) power divider. A double-Y balun feeding structure is also used to transition from the CPW to the coplanar slot line (CPS). Two techniques are investigated to enhance the antenna's radiation characteristics. The first technique involves incorporating equal corrugations along the edges of the flare aperture, resulting in a significant gain enhancement of 0.9 dBi and an improvement in radiation efficiency by 7%. The second technique …

Gratings In Optical Waveguides And Lasers, Weida Zhang

Electrical Engineering Theses and Dissertations

Gratings play a crucial role in Distributed Bragg reflector (DBR) lasers, influencing their performance and characteristics. The focus of this work is aimed at the design of DBR lasers that significantly impact the laser's spectral and temporal behavior, making it a key component in optimizing DBR laser functionality.

The SMU developed grating software, compared with commercially available photonics software, has improved accuracy and much smaller computation times. The improved accuracy and reduced computation times compared with commercial photonics software occur because commercial software is typically based on numerical methods such as finite-difference time-domain (FDTD), eigenmode expansion and beam propagation methods …

Electromagnetic Theory And Applications, 2nd Edition, Nicholas Madamopoulos, George Kliros

Open Educational Resources

This book intends to provide both the fundamentals of Electromagnetics but also some practical applications of the concepts covered. Having taught electromagnetics for several years, the authors feel that many times the field of electromagnetics comes as “old” and often times students do not appreciate the concepts and their importance in everyday applications. The authors intend to accompany the EM concepts with life applications. Hence, students may see the direct impact of the knowledge they acquire through the study of the field of electromagnetics and better appreciate the field.

Fabrication And Characterization Of A Monolithic Photonic Integrated Circuit With High-Aspect Ratio Photonic Device Structures, Sami A. Nazib

Optical Science and Engineering ETDs

The focus of this work was to create a process to fabricate an InP-based Photonic Integrated Circuit (PIC). The design of the PIC required the photonic components of this device to be created by deep etching of an epitaxially-grown multilayer structure. Therefore, a novel dry etching process was developed to produce very high aspect- ratio (HAR) features. This process not only involved the development of dry etch chemistry but also the engineering of a metal mask structure. The next step of the challenge was to use a polymer-based material that would have two functions: cladding for the etched photonic components …

Fast And Accurate Automatic Design Of Spiral Inductors From High-Level Specification, Heba Ismail

Theses and Dissertations

Integrated on-chip planar spiral inductors are widely employed in communication circuit blocks and other various electronic devices, thus becoming an essential passive component of RF integrated circuits (RFICs). A common vital spiral inductor design problem is determining the optimum layout parameters of spiral inductors that yield the desired inductance value and achieve highest quality factor at the intended operating frequency. Various approaches tackle this difficulty, but the most prevalent approaches for designing inductors are using an electromagnetic simulator or a library of pre-designed inductors. The latter approach requires an extensive amount of time and computational resources, whereas the former restricts …

Nano-Patterned Si Structures For Optical Filters And Electro-Mechanical Relays: Fabrication, Characterization, Prospects, And Limitations, Md Ataul Mamun

Theses and Dissertations

Nanofabrication technology, especially nanopatterning, is a rapidly advancing field that has already resulted in creating novel devices and holds promise for producing even more with unmatched performance. These techniques also allow us to gain insight into physical phenomena at the micro- and nanoscale. The ultimate performance of nanofabricated devices and their compatibility with existing Si-based CMOS technology hinge upon the careful selection of materials and precise design, coordinated with meticulous pattern transfer. In this work, we applied nanopatterning techniques on silicon to create optical filters for the shortwave infrared (SWIR) region and nanoelectromechanical system (NEMS) relay-based logic gates. Additionally, these …

Semiconductor Photonic Crystal Surface Emitting Lasers For High Power, High Brightness And High Speed Applications, Chhabindra Gautam

Electrical Engineering Dissertations - Archive

Photonic Crystal Surface Emitting Laser (PCSEL) is the promising third generation semiconductor laser technology as it addresses the challenges of the conventional semiconductor lasers (EEL/VCSEL) by providing single mode high power output with good beam quality (thus high brightness). The large area in plane coupling resulting from the multiple Bragg’s diffraction conditions in the periodic 2D photonic crystal cavities in the lasing cladding region leads to single mode operation over very large area. By model design engineering, such in plane lasing cavity can leak the light out of the plane, which result in surface emission. The ability to scale the …

Gas Assisted Electron Beam Patterning Processes, Deepak Kumar

Theses and Dissertations--Electrical and Computer Engineering

Radiolysis is a complex phenomenon in which molecules subjected to ionizing radiation form new chemical species. Electron-beam irradiation has proven to be a versatile approach for significantly altering materials’ properties and forms the basis for electron-beam lithography using both organic and inorganic resists. Electron-beam exposure is normally carried out under high vacuum conditions to reduce contamination and allow for unhindered interaction between the electrons and the resist material. Exposure under an ambient gas at sub-atmospheric pressures has been found to provide a distinct mechanism which can be exploited to circumvent some of the challenges associated with material processing and significantly …

Reinventing Integrated Photonic Devices And Circuits For High Performance Communication And Computing Applications, Venkata Sai Praneeth Karempudi

Theses and Dissertations--Electrical and Computer Engineering

The long-standing technological pillars for computing systems evolution, namely Moore's law and Von Neumann architecture, are breaking down under the pressure of meeting the capacity and energy efficiency demands of computing and communication architectures that are designed to process modern data-centric applications related to Artificial Intelligence (AI), Big Data, and Internet-of-Things (IoT). In response, both industry and academia have turned to 'more-than-Moore' technologies for realizing hardware architectures for communication and computing. Fortunately, Silicon Photonics (SiPh) has emerged as one highly promising ‘more-than-Moore’ technology. Recent progress has enabled SiPh-based interconnects to outperform traditional electrical interconnects, offering advantages like high bandwidth density, …

Spin Wave Devices For Embedded Applications And Information Processing, Raisa Fabiha

Theses and Dissertations

Device miniaturization is a prerequisite for modern day electronics. Spintronics offers immense potential in energy efficient data storage, solid states devices, ultrafast computing and other electronic applications because of their low power consumption, non-volatile nature and unique activation mechanism. The conventional nano-antennas used for wireless communication, biomedical and wearable devices and IoT applications are limited by the traditional Harrington limit. As we attempt to miniaturize the antenna size beyond its emitted wavelength (also called “subwavelength” antenna), its gain and efficiency plummet. To overcome this challenge, the researchers have proposed magnetoelectric antennas. The ultra-thin film based magnetoelastic antennas suffer from eddy …

Improving Cellphone-Based Bio-Imaging Technique For Fluorescence Detection, Erteza T. Efaz

LSU Master's Theses

The research presented in this thesis focuses on the design, development, and evaluation of a fluorescence detection system. The system is implemented primarily as an Android application, Auto Camera, which leverages smartphone cameras to capture and analyze fluorescent images. The application provides a user-friendly interface with some configurable features like exposure time, ISO speed, and storage limit; as well as defining detection thresholds and setting acquisition intervals. This study begins with the architectural framework of the Android application, which is written in Java using Android Studio. The API compatibility is set to version 33, and users are prompted to grant …

Characterization Of Low Power Hfo2 Based Switching Devices For In-Memory Computing, Aseel Zeinati

Theses

Oxide based Resistive Random Access Memory (RRAM) devices are investigated as one of the promising non-volatile memories to be used for in-memory computing that will replace the classical von Neumann architecture and reduce the power consumption. These applications required multilevel cell (MLC) characteristics that can be achieved in RRAM devices. One of the methods to achieve this analog switching behavior is by performing an optimized electrical pulse. The RRAM device structure is basically an insulator between two metals as metal-insulator-metal (MIM) structure. Where one of the primary challenges is to assign an RRAM stack with both low power consumption and …

Carrier Transport Engineering In Wide Bandgap Semiconductors For Photonic And Memory Device Applications, Ravi Teja Velpula

Dissertations

Wide bandgap (WBG) semiconductors play a crucial role in the current solid-state lighting technology. The AlGaN compound semiconductor is widely used for ultraviolet (UV) light-emitting diodes (LEDs), however, the efficiency of these LEDs is largely in a single-digit percentage range due to several factors. Until recently, AlInN alloy has been relatively unexplored, though it holds potential for light-emitters operating in the visible and UV regions. In this dissertation, the first axial AlInN core-shell nanowire UV LEDs operating in the UV-A and UV-B regions with an internal quantum efficiency (IQE) of 52% are demonstrated. Moreover, the light extraction efficiency of this …

Void-Semiconductor Gaas Photonic Crystal Surface-Emitting Lasers By Epitaxial Regrowth And Single-Epitaxy Methods, Kevin James Reilly

Nanoscience and Microsystems ETDs

Monolithic semiconductor lasers including edge-emitting lasers (EELs) and vertical-cavity surface-emitting lasers (VCSELs) fail to realize simultaneous achievement of both high-power high-quality beams due to intrinsic limitations of their resonant cavity. Photonic crystal surface emitting lasers (PCSELs) address these structural limitations through employment of a two-dimensional photonic crystal (PC) cavity that creates feedback at a single wavelength for laterally scalable devices. This function of the PC allows PCSELs to power scale with area while maintaining single-mode emission required for diffraction-limited beams. In this way, PCSELs fulfill an industry demand for high-power high-quality lasing from a single chip.

Early PCSELs were fabricated …

Reliability Enhancing Control Algorithms For Two-Stage Grid-Tied Inverters, Yuheng Wu

Graduate Theses and Dissertations

In the photovoltaic (PV) generation system, two types of grid-tied inverter systems are usually deployed: the single-stage grid-tied inverter system and the two-stage grid-tied inverter system. In the single-stage grid-tied inverter system, the input of the inverter is directly connected to the PV arrays, while an additional dc-dc stage is inserted between the PV arrays and the dc-ac inverter in the two-stage design. The additional dc-dc stage could provide a stable dc-link voltage to the inverter, which also enables new design possibilities, including the multi-MPPT operation and solar-plus-storage application. Thus, the two-stage grid-tied inverter has been widely used in the …

Design Of Arbitrary Planar Optical Devices With Full Phase Control Using Nanoimprinting Of Refractive Index, Matthew Panipinto

All Theses

Planar optical devices offer a lightweight solution to the constraints found in traditional optical devices. While subwavelength patterning of optics offers attractive performance and size, traditional fabrication methods demand a trade-off between resolution and throughput that presents a significant hurdle for the widespread use of subwavelength devices. Nanoimprinting of refractive index (NIRI) is a novel fabrication method pioneered in previous work that offers promise in mitigating the throughput issues that hamstring traditional fabrication methods. However, NIRI has not been shown to impart full $2\pi$ phase control in planar optical devices, nor has a method for fabricating arbitrary designs using the …

Design And Analysis Of A Discrete, Pcb-Level Low-Power, Microwave Cross-Coupled Differential Lc Voltage-Controlled Oscillator, Pavin Singh Virdee

Master's Theses

Radio Frequency (RF) and Microwave devices are typically implemented in Integrated Circuit (IC) form to minimize parasitics, increase precision and tolerances, and minimize size. Although IC fabrication for students and independent engineers is cost-prohibitive, an abundance of low-cost, easily accessible printed circuit board (PCB) and electronic component manufacturers allows affordable PCB fabrication.

While nearly all microwave voltage-controlled oscillator (VCO) designs are IC-based, this study presents a discrete PCB-level cross-coupled, differential LC VCO to demonstrate this more affordable and accessible approach. This thesis presents a 65 mW, discrete component VCO PCB with industry-comparable RF performance. A phase noise of -103.7 dBc/Hz …

Surface-Wave Coupling In Double Floquet Sheets Supporting Phased Temporal Wood Anomalies, Ya-Wen Tsai, Yao-Ting Wang, Emanuele Galiffi, Andrea Alù, Ta-Jen Yen

Advanced Science Research Center

We investigate symmetry-selective surface-mode excitation in a general periodically time-modulated double-layer system, where the modulation of the two layers has a constant phase difference. By deriving a semi-analytic transfer matrix formalism of a Drude-dispersive double-layer structure with periodic time-modulation, we calculate the scattering amplitudes and the corresponding transmission coefficient. Our results show that the phase-difference between the modulation of the two sheets plays an essential role in significantly enhancing and selectively exciting either the even or odd surface mode with high efficiency. We verify our calculations with full-wave time-domain simulations, showing that efficient switching between the surface-wave excitation of the …

X-Band Rf Transmitter Design For Multi-Purpose Small Satellite Communication Operations, Omer F. Gumus

Master's Theses

This thesis provides a description of the analysis, design, and tests of an X-band RF Transmitter communication system for small satellites. X-band transmitter systems are becoming popular in the upcoming deep space missions. Most of the deep-space ground stations have been using X-band frequencies to receive or transmit signals. The X-band (<10 GHz) can offer lower atmospheric losses and up to a couple of Mbps data rates for multiple satellite operations. Nowadays, many small satellites have been using frequency bands such as VHF, UHF, L, and S-band frequencies for communication. From deep space to the ground station, the low-frequency ranges are inadequate in providing Mbps level data rates and enough bandwidth for deep space missions.

The main focus of this thesis was the development of the subsystems such as gain block amplifier, Mixer, Bandpass Filter, and RF power amplifier. The subsystems were designed separately, then they were connected together to perform an end-to-end system test. One of the thesis aims is to design …

Second-Order Enhanced Coupling Strength Grating Out-Couplers For A Monolithic Laser-Electro-Absorption Modulator, Maryam Dezfuli

Electrical Engineering Theses and Dissertations

Conventional grating out-couplers in III-V waveguides typically require lengths of several hundreds of microns to outcouple 50 to 90% of the incident optical power. Enhanced coupling strength (ECS) gratings, which reduce the out-coupler grating length to tens of microns, have a large relative permittivity difference between the materials on either side of the grating boundary along with a high index cover layer. With appropriately chosen permittivity and layer thicknesses, the addition of a cover layer “pulls” the peak of the optical mode towards the grating region, resulting in a significant increase in the grating confinement factor. The resulting ECS out-coupler …