Electromagnetics and Photonics Commons^™

Corrections To ‘‘Glaciernet: A Deep-Learning Approach For Debris-Covered Glacier Mapping’’, Zhiyuan Xie, Umesh K. Haritashya, Vijayan K. Asari, Brennan W. Young, Michael P. Bishop, Jeffrey S. Kargel

Electrical and Computer Engineering Faculty Publications

In the above article [1], Figure 2 was incorrect. Unfortunately, we mixed the color label of "CONV $\to $ BN $\to $ ReLu" and "Unpooling" in the CNN structure section of Figure 2. The color label of "CONV $\to $ BN $\to $ ReLu" should be orange while the color label of "Unpooling" should be green. Also, the word "Decoder" is misspelled. That same figure with the same error is also used for the graphic abstract. The corrected figure is given here. None of the sections in the figure is modified. The only change is in the color label of …

Transient Mid-Ir Nonlinear Refraction In Air And Nonlinear Optical Properties Of Organometallic Complexes, Salimeh Tofighi

Electronic Theses and Dissertations, 2020-2023

This dissertation explores two main topics: Transient nonlinear refraction of air in Mid-IR spectral range and nonlinear optical properties of organometallic complexes. For seeing a vibrational and rotational Raman response the molecule should be Raman active. The first requirement for being a Raman active molecule is that the polarizability of molecule must be anisotropic. Linear symmetric molecules do have rotational Raman spectra. Not all the vibrational mode can be excited by a femtosecond pulse. The pulsewidth of our excitation beam should be less than the half of the vibration period. In this dissertation my excitation pulsewidth is not short enough …

Development Of High-Power Single-Mode Yb-Doped Fiber Amplifiers And Beam Analysis, Steffen Wittek

Electronic Theses and Dissertations, 2020-2023

High-power fiber laser systems enjoy a widespread use in manufacturing, medical, and defense applications as well as scientific research, due to their remarkable power scalability, high electrical to optical efficiency, compactness and ruggedness. However, single-mode fiber power scaling has stagnated in the past years, primarily due to the onset of nonlinear effects such as stimulated Brillouin/Raman scattering and transverse modal instabilities. This thesis addresses the analysis and mitigation of transverse modal instabilities in high-power fiber amplifiers. I describe the high-power fiber amplifier testbed that I set up to test fibers fabricated in house. I will show our results of a …

Attosecond Transient Absorption Spectroscopy In The Water Window, Andrew Chew

Electronic Theses and Dissertations, 2020-2023

The push to study the atomic and molecular dynamics at ever smaller time scales has been the main driving force for developing laser systems with ever shorter pulse durations. Thus far, picosecond lasers and femtosecond lasers have been used with great success in femtochemistry to study molecular dynamics such as molecular rotation and vibration, which all occur in the tens to hundreds of femtosecond. To study electron dynamics however, which are on the order of attoseconds, one needs attosecond laser sources to be able to have the time resolution required to probe ultrafast electron dynamics such as AC Stark shifts, …

Analysis Of Antenna Designs For The Maximum Power Transmission, Lauryn P. Smith

College of Graduate Studies: Theses & Dissertations

Since Nikola Tesla discovered wireless power transmission, it has become a very interesting topic of study in the antennas and wireless propagation community. Various aspects and applications for wireless power transmission are studied today, a few of which are investigated in this work. First, various antenna geometries are analyzed for radiative near-field wireless power transfer in terms of electrical field strength. It is determined that the meander antenna is ideal for maximum power transfer in its radiative near-field region, contrary to its far-field behavior. Next, in the application of radio frequency identification, a directive, UHF RFID tag antenna is designed …

Development Of An Anatomically And Electrically Conductive Brain Phantom For Transcranial Magnetic Stimulation, Hamzah A. Magsood

Theses and Dissertations

Transcranial Magnetic Stimulation (TMS) is a non-invasive technique for diagnostics, prognostic, and treatments of various neurological diseases. However, the lack of anatomically realistic brain phantoms has made the experimental verification of stimulation strength in the form of induced electric fields/voltages in the brain tissues an impediment to developing new TMS coils, stimulators, and treatment protocols. There are significant technological, safety, and ethical limitations to test the potential TMS treatment procedures or develop enhancements and refine them on humans or animals. This work aims to bridge the gap by introducing and developing an innovative manufacturing and fabrications process to produce a …

High-Fidelity Mini-Led And Micro-Led Displays, Yuge Huang

Electronic Theses and Dissertations, 2020-2023

Mini-LED and micro-LED are emerging disruptive display technologies, because they can work as local dimmable backlight to significantly enhance the dynamic range of conventional LCDs, or as sunlight readable emissive displays. However, there are still unresolved issues impairing their display fidelity: 1) motion blur on high-resolution, large-size and high-luminance devices, 2) limited contrast ratio on mini-LED backlit LCD (mLED-LCD), 3) relatively high power consumption, and 4) compromised ambient contrast ratio. This dissertation tackles with each of these issues for achieving high display fidelity. Motion blur is caused by slow liquid crystal response time and image update delays. Low-duty ratio operation …

Multi-Parameter Optical Metrology: Quantum And Classical, Walker Larson

Electronic Theses and Dissertations, 2020-2023

The insights offered by quantum mechanics to the field of optical metrology are many-fold, with non-classical states of light themselves used to make sensors that surpass the sensitivity of sensors using classical states of light. Unfortunately, this advantage, referred to often as "super-sensitivity" is notoriously fragile, and even the slightest experimental imperfections may greatly reduce the efficacy of the non-classical sensors, sometimes completely obviating their advantage. In my thesis I have shown that the performance of an otherwise ideal two-photon interferometer, which exploits entanglement between photons to make super-sensitive measurements of phase, is crippled by the slightest introduction of decoherence …

Midwave Vs Longwave Infrared Search And Track And Aerosol Scattering Target Acquisition Performance, Steven Butrimas

Electronic Theses and Dissertations, 2020-2023

The decision on whether to use a mid wave infrared (MWIR) or long wave infrared (LWIR) sensor for a given task can be a formidable verdict. The scope entails facts about the observable source, the atmospheric interactions, and the sensor parameters within the hardware device. Even when all the individual metrics are known, the combination ultimately determines whether a MWIR or LWIR sensor is more appropriate. Despite the vast number of variables at play, the reduction of inputs through focused studies can provide essential insight into MWIR and LWIR comparisons. This dissertation focuses on the roles of point source target …

Heterogeneous Integrated Photonics For Nonlinear Frequency Conversion And Polarization Diversity, Tracy Sjaardema

Electronic Theses and Dissertations, 2020-2023

Silicon has proven to be one of the materials of choice for many integrated photonic applications. However, silicon photonics is limited by certain material shortcomings. Two shortcomings addressed in this work are zero second-order optical nonlinearity, and the lack of methods available to achieve broadband polarization diversity. Heterogeneous integrated solutions for these shortcomings of silicon photonics are presented in this work. First, nonlinear frequency conversion is demonstrated with thin-film lithium niobate on silicon substrates. The method for reaching the highest-achieved second-harmonic generation conversion efficiency, using active monitoring during periodic poling, is discussed. Additionally, a cascaded approach for generating higher-order harmonics …

Ev Charging Behavior Analysis Using Hybrid Intelligence For 5g Smart Grid, Yi Shen, Wei Fang, Feng Ye, Michel Kadoch

Electrical and Computer Engineering Faculty Publications

With the development of the Internet of Things (IoT) and the widespread use of electric vehicles (EV), vehicle-to-grid (V2G) has sparked considerable discussion as an energy-management technology. Due to the inherently high maneuverability of EVs, V2G systems must provide on-demand service for EVs. Therefore, in this work, we propose a hybrid computing architecture based on fog and cloud with applications in 5G-based V2G networks. This architecture allows the bi-directional flow of power and information between schedulable EVs and smart grids (SGs) to improve the quality of service and cost-effectiveness of energy service providers. However, it is very important to select …

Innovative Applications Of Laser Remote Sensing Of Gases, Aerosols And Wind, Adrian Diaz Fortich

Dissertations and Theses

Over the years, a major component of the research carried out at the Optical Remote Sensing Laboratory of the City College of New York has been on active sensing technologies and their different applications in atmospheric studies. This thesis builds upon and looks to further advance this field by demonstrating innovative applications of laser remote sensing technologies for studies involving trace gases, aerosol particles and wind; which are key components of the Earth’s atmosphere. First, we present the demonstration of gas concentration measurements using a quantum cascade laser open path system with characteristics that make it promising for mobile and/or …

Glaciernet: A Deep-Learning Approach For Debris-Covered Glacier Mapping, Zhiyuan Xie, Umesh K. Haritashya, Vijayan K. Asari, Brennan W. Young, Michael P. Bishop, Jeffrey S. Kargel

Electrical and Computer Engineering Faculty Publications

Rising global temperatures over the past decades is directly affecting glacier dynamics. To understand glacier fluctuations and document regional glacier-state trends, glacier-boundary detection is necessary. Debris-covered glacier (DCG) mapping, however, is notoriously difficult using conventional geospatial technology methods. Therefore, in this research for automated DCG mapping, we evaluate the utility of a convolutional neural network (CNN), which is a deep learning feed-forward neural network. The CNN inputs include Landsat satellite images, an Advanced Land Observation Satellite (ALOS) digital elevation model (DEM) and DEM-derived land-surface parameters. Our CNN based deep-learning approach named GlacierNet was designed by appropriately choosing the type, number …

Mitosisnet: End-To-End Mitotic Cell Detection By Multi-Task Learning, Md Zahangir Alom, Theus Aspiras, Tarek M. Taha, Tj Bowen, Vijayan K. Asari

Electrical and Computer Engineering Faculty Publications

Mitotic cell detection is one of the challenging problems in the field of computational pathology. Currently, mitotic cell detection and counting are one of the strongest prognostic markers for breast cancer diagnosis. The clinical visual inspection on histology slides is tedious, error prone, and time consuming for the pathologist. Thus, automatic mitotic cell detection approaches are highly demanded in clinical practice. In this paper, we propose an end-to-end multi-task learning system for mitosis detection from pathological images which is named"MitosisNet". MitosisNet consist of segmentation, detection, and classification models where the segmentation, and detection models are used for mitosis reference region …

Serdes Channel Crosstalk Mitigation Methodology With Industrial Implementation Guidance, Junda Wang

Masters Theses

"With the increasing data rate of digital circuits, the differential crosstalk degrades the signal integrity performance in PCBs drastically. Usually, in the trace area, crosstalk can be isolated by stitching vias and adding shielding ground vias can also shield coupling in the ball gate array (BGA) and pin field area. The traditional way to mitigation crosstalk in the BGA and pin field area through adding more ground vias between signal pairs or increasing the spacing in between, it demonstrated us the efficiency on crosstalk cancellation efficiency but it also increases the size of products and it would be contradictory to …

An Emi Characterization And Modeling Study For Consumer Electronics And Integrated Circuits, Chunyu Wu

Doctoral Dissertations

“As internet-of-things (IoT) applications surge, wireless connectivity becomes an essential part of the network. Smart home, one of the most promising application scenarios of IoT, will improve our life quality enormously. However, electromagnetic interference (EMI) to the receiving antenna, either from another electronic product or from a module/an integrated circuit(IC) inside the same wireless device, will degrade the performance of wireless connectivity, thus influencing the user experience. Characterization and modeling of the EMI become increasingly important.

In the first part, an improved method to extract equivalent dipoles from magnitude- only electromagnetic-field data based on the genetic algorithm and back-and-forth iteration …

Independent And Simultaneous Control Of Electromagnetic Wave Properties In Self-Collimating Photonic Crystals Using Spatial Variance, Jesus Javier Gutierrez

Open Access Theses & Dissertations

Photonic crystals are engineered periodic structures that provide great control over electromagnetic waves. One of these mechanisms is self-collimation, in which the electromagnetic wave travels through the photonic crystal along an axis of the lattice without diffracting or spreading. This mechanism of self-collimation is a dispersion phenomenon, which is dependent on the unit cell's physical and geometrical characteristics. An algorithm for generating spatially variant lattices (SVL) was developed that can change geometrical properties in photonic crystals as a function of position, like unit cell orientation, fill fraction, symmetry, and others in a manner that is smooth, continuous, and virtually free …

Flux Expulsion In Niobium Superconducting Radio-Frequency Cavities Of Different Purity And Essential Contributions To The Flux Sensitivity, P. Dhakal, Gianluigi Ciovati, Alex Gurevich

Physics Faculty Publications

Magnetic flux trapped during the cooldown of superconducting radio-frequency cavities through the transition temperature due to incomplete Meissner state is known to be a significant source of radio-frequency losses. The sensitivity of flux trapping depends on the distribution and the type of defects and impurities which pin vortices, as well as the cooldown dynamics when the cavity transitions from a normal to superconducting state. Here we present the results of measurements of the flux trapping sensitivity on 1.3 GHz elliptical cavities made from large-grain niobium with different purity for different cooldown dynamics and surface treatments. The results show that lower …

Kettlebell Ultra, Elissa Peters, Kathryn Wegman, Daniel Basch, Mason Pastorius

Williams Honors College, Honors Research Projects

This project will consist of an attachment to an average kettlebell that will track the number of repetitions that the user has performed. The device will send this data over Bluetooth to a smart phone application so the user can track their workout accurately.

Levitate, Stephen Hargreaves, Isaac Hammonds, Russel Pease, Joseph Morris

Williams Honors College, Honors Research Projects

Levitate is designed to create a healthier work environment by providing a way of entertaining a worker while not distracting them. To fulfill this task, the device needs to be interesting and self-sufficient while not being overly flashy. To complete this task, Levitate is designed so that it is able to lift a platform from rest using magnetism and that will be able to stabilize itself using electromagnets. It initiates this process by lifting the permanent magnet using servo motors. Then, the device is able to achieve stability through the use of hall sensors feeding their results to the board …

Rapid Prototyping Of Nanostructures With Electron Beam Induced Processing, Samaneh Esfandiarpour

Theses and Dissertations--Electrical and Computer Engineering

Focused electron beam induced processing (FEBIP) is a nano-scale fabrication technique that allows the direct deposition of functional materials. However, it suffers from significant drawbacks, such as high cost, low speed, unavailable precursors for many materials and low purity of deposits. Liquid-phase focused electron beam induced processes (LP-FEBIP) are being investigated due to the potential benefits over the gas phase technique. In this method, deposition or etching occurs at the interface between a substrate and a bulk liquid. In this work, electron beam induced deposition of copper nanostructures from aqueous solutions of copper sulfate is demonstrated. The addition of sulfuric …

Parallelized X-Ray Tracing With Gpu Ray-Tracing Engine, Joseph Ulseth

Electronic Theses and Dissertations, 2020-2023

X-ray diffraction tomography (XDT) is used to probe material composition of objects, providing improved contrast between materials compared to conventional transmission based computed tomography (CT). In this work, a small angle approximation to Bragg's Equation of diffraction is coupled with parallelized computing using Graphics Processing Units (GPUs) to accelerate XDT simulations. The approximation gives rise to a simple yet useful proportionality between momentum transfer, radial distance of diffracted signal with respect to incoming beam's location, and depth of material, so that ray tracing may be parallelized. NVIDIA's OptiX ray-tracing engine, a parallelized pipeline for GPUs, is employed to perform XDT …

Fluorescence Microscopy With Tailored Illumination Light, Jialei Tang

Electronic Theses and Dissertations, 2020-2023

Fluorescence microscopy has long been a valuable tool for biological and medical imaging. Control of optical parameters such as the amplitude, phase, polarization and propagation angle of light gives fluorescence imaging great capabilities ranging from single molecule imaging to long-term observation of living organisms. While numerous fluorescence imaging techniques have been developed over the past decades, there is always an inevitable tradeoff among the spatial resolution, imaging speed, contrast, photodamage and the total cost when it comes to choose the appropriate microscope. A main goal of my dissertation research is to develop state-of-the-art microscope systems that exhibit unprecedented performance in …

Nonlinear Optical Mechanisms In Semiconductors And Enhanced Nonlinearities At Epsilon-Near-Zero, Sepehr Ahmadzadeh Benis

Electronic Theses and Dissertations, 2020-2023

Light does not interact with itself in linear optical materials. Such interactions occur only in non-linear optical (NLO) materials and typically require high intensity optical beams to be signifi-cant. The ever-increasing role of NLO, where intense light may change the properties of the me-dium, has created a pressing demand to invent materials for achieving more efficient light-light and light-matter interaction due to their potential capacity to augment and possibly replace cur-rent technologies with more efficient devices. There are numerous applications of NLO devices in fundamental science, technology, health, and defense such as all-optical computation and sig-nal processing, ultrashort laser technology, …

Iterative Optical Diffraction Tomography For Reconstruction Of Multiply-Scattering Objects, Shengli Fan

Electronic Theses and Dissertations, 2020-2023

As a label-free, non-destructive, high-resolution, and quantitative imaging technique, optical diffraction tomography (ODT) has been widely used to image biological samples and microstructures, such as cells, tissues, and optical fibers. The refractive-index (RI) distribution of an object is reconstructed from multi-view measurements of diffracted fields emerging from the object. Typical ODT setups include the object rotating configuration (ORC) and the illumination scanning configuration (ISC). One major limitation of ODT is that it is only applicable to weakly-scattering objects. In this dissertation, novel methods have been developed to overcome the reconstruction difficulty caused by multiple scattering, so as to extend ODT …

Investigation Of Phonon Polaritons In An Hbn Gan Heterostructure, Catherine G. O'Hearn

Graduate Theses, Dissertations, and Problem Reports (ETD)

There have been many great advances in the generation and manipulation of optics in the visible and near infrared (IR) range over the past decade. This is largely due to plasmonic enhancement, which has led to new technology in biosensing and molecule detection, solid-state lighting, and solar energy harvesting. The field of plasmonics uses quanta of plasma oscillations, plasmons, formed from the interaction between electromagnetic radiation and free electrons to enhance optical near field magnitudes. However, there is still a large region of the electromagnetic spectrum, covering the mid-infrared (MIR) and terahertz (THz) regions, ranging from 3 μm to 1 …

Parametric Optimization Of Visible Wavelength Gold Lattice Geometries For Improved Plasmon-Enhanced Fluorescence Spectroscopy, Casey A. Norville

Graduate Theses, Dissertations, and Problem Reports (ETD)

The exploitation of spectro-plasmonics will allow for innovations in optical instrumentation development and the realization of more efficient optical biodetection components. Biosensors have been shown to improve the overall quality of life through real-time detection of various antibody-antigen reactions, biomarkers, infectious diseases, pathogens, toxins, viruses, etc. has led to increased interest in the research and development of these devices. Further advancements in modern biosensor development will be realized through novel electrochemical, electromechanical, bioelectrical, and/or optical transduction methods aimed at reducing the size, cost, and limit of detection (LOD) of these sensor systems. One such method of optical transduction involves the …

Design And Development Of Fiber Bragg Grating Sensor For Detecting Of Hydrogen Gas In Transformer Oil, Mohd Raffi Samsudin

Student Works (2020-2029)

Hermetically sealed oil-immersed transformers are the key to electricity distribution networks. They are also one of the most expensive facilities in the electricity supply network. Immediate replacement is expected for this type of transformer upon failure because it is directly connected to the customer. Transformer oil acts as insulation, coolant and condition indicator. To date, there is no economical real-time monitoring system available to monitor the transformer oil condition. Therefore, there is a need to develop a cheap, non-intrusive and non-electrical sensor to monitor the health of the transformer by measuring the amount of dissolved hydrogen gas in oil, which …

Improving The Efficiency Of Planar Goubau Line And Goubau-Line-Based Endfire Antenna, Sreelakshmi Radhakrishnan

Graduate Research Theses & Dissertations

This thesis presents the use of two dielectric layers in a planar Goubau line (PGL) to improve its transmission efficiency compared to the existing single-layer models, which is less than 70% efficient at lower frequencies up to 5 GHz. Further, as an extension of the thesis, the possibility of obtaining directive radiation pattern with radiation efficiency greater than 89.6% using a Goubau-line-based antenna is studied. While none of the existing Goubau-line-based antennas are able to obtain an endfire pattern with radiation efficiency of above 80%, the proposed model utilizes stubs that are periodically attached to the main line of length …

Multi-Physics-Based Approach To Active Microwave Thermography, Seyed Ali Mirala

Doctoral Dissertations

“The goal of this work is to advance a novel nondestructive testing (NDT) method for controlled, rapid, and effective inspection of a structure through the integration of microwave NDT and thermography, referred to as Active Microwave Thermography (AMT). In AMT, the structure under test is exposed to microwave radiation and the thermal profile of the structure is monitored via a thermal camera in order to obtain desired information regarding the structure. This new technique is applicable across a wide range of NDT needs including detection of voids, delamination, water ingress, debonding, and cracks in numerous structures such as carbon fiber …