Electromagnetics and Photonics Commons^™

Performance Of Siso And Mimo Antenna Systems In Suburban And Urban Scenarios For V2i Communications At 5.9 Ghz And 28 Ghz, Oluwaseun Falade

Theses and Dissertations

As the need for Vehicle to Infrastructure (V2I) innovations increases, further research is needed to test the performance of antennas installed on vehicles in realistic scenarios including their radiation patterns and optimal location. This thesis considers realistic suburban and urban scenarios with SISO and MIMO antennas for V2I systems at 5.9 GHz and 28 GHz. The simulation is based on Ray tracing (RT) channel models to accurately model the effects of obstacles such as buildings and vehicles on the communication signals. Time-varying vehicular environments are simulated using a 3-D RT tool involving a vehicle and a base station. This research …

Exploring Bistatic Scattering Modeling For Land Surface Applications Using Radio Spectrum Recycling In The Signal Of Opportunity Coherent Bistatic Simulator, Dylan R. Boyd

Theses and Dissertations

The potential for high spatio-temporal resolution microwave measurements has urged the adoption of the signals of opportunity (SoOp) passive radar technique for use in remote sensing. Recent trends in particular target highly complex remote sensing problems such as root-zone soil moisture and snow water equivalent. This dissertation explores the continued open-sourcing of the SoOp coherent bistatic scattering model (SCoBi) and its use in soil moisture sensing applications. Starting from ground-based applications, the feasibility of root-zone soil moisture remote sensing is assessed using available SoOp resources below L-band. A modularized, spaceborne model is then developed to simulate land-surface scattering and delay-Doppler …

Tunable Linewidth Chip-Level Lasers Using Hybrid Integration Methods, Charles Porter

All Theses

Photonic integrated circuits (PICs) have significant value in today’s world of research. They enable devices to experience large reductions in size, weight, operation power, and cost (SWAPc), making photonic technology more accessible than ever. The functionality of PICs is greatly enhanced due to the realization of both active and passive devices within a single device structure. This is made possible through hybrid integration, which utilizes various coupling methods to transfer light from an active chip to a passive chip. Hybrid integration technology tremendously expands the capabilities of PICs, leading to a plethora of applications. One significant application is that of …

Characteristics Of Refractivity And Sea State In The Marine Atmospheric Surface Layer And Their Influence On X-Band Propagation, Douglas Matthew Pastore

Electronic Theses and Dissertations

Predictions of environmental conditions within the marine atmospheric surface layer (MASL) are important to X-band radar system performance. Anomalous propagation occurs in conditions of non-standard atmospheric refractivity, driven by the virtually permanent presence of evaporation ducts (ED) in marine environments. Evaporation ducts are commonly characterized by the evaporation duct height (EDH), evaporation duct strength, and the gradients below the EDH, known as the evaporation duct curvature. Refractivity, and subsequent features, are estimated in the MASL primarily using four methods: in-situ measurements, numerical weather and surface layer modeling, boundary layer theory, and inversion methods.

The existing refractivity estimation techniques often assume …

Design And Fabrication Of An Optical Blade Tip Timing Sensor, Nick Tomlinson

All Theses

Electricity is a vital energy source that powers modern technology. Turbines are heavily relied on in the electric power industry for the conversion of natural energy sources into electricity. These turbines operate under harsh conditions which increase the likelihood of blade damage. Structural health monitoring of a turbine’s blades is important to detect problems before a blade experiences failure. The blade tip timing method can be used to monitor blade vibrations and determine if damage has occurred. An optical blade tip timing sensor is designed and fabricated to advance the field of sensing in the power industry.

Miniature, Submersible Electromagnetic Pumps Of Molten Lead And Sodium For Gen-Iv Nuclear Reactors Development, Ragai M. Altamimi

Nuclear Engineering ETDs

Heavy metals and alkali Liquid Metals are suitable coolants for Generation IV terrestrial nuclear reactors for operating at elevated temperatures for achieving plant thermal efficiency more than 40% and the thermochemical generation of hydrogen fuel. In addition, the low vapor pressure of these liquids eliminates the need for a pressure vessel and instead operates slightly below ambient pressure. A primary issue with the uses of these coolants is their compatibility with nuclear fuel, cladding and core structure materials at elevated temperatures more than 500oC. Therefore, in pile and out-of-pile test loops have been constructed or being considered for quantifying the …

Fabrication And Measurement Of Lt-Gaas Photoconductive Antennas And Arrays, Zachary Paul Uttley

Graduate Theses and Dissertations

This thesis presents the fabrication and measurement of LT-GaAs based terahertz (THz) photo conductive antennas (PCAs) and arrays. The LT-GaAs THz PCAs are fabricated to serve as reference devices to new 2D material black phosphorous (BP) based THz PCAs. The LT-GaAs and BP devices have identical metallic electrodes, allowing for a comparison of emitted THz intensity and bandwidth. All PCAs have been measured using an open bench pulsed time-domain spectroscopy (TDS) system with a usable bandwidth from 0.1-4 THz, pumped with a 780nm Ti:Sapphire femtosecond laser. The results have shown LT-GaAs devices outperforming BP devices in signal amplitude and bandwidth …

Adaptive Gps Antenna Array Beam Nulling Effectiveness Under Varying Antenna Element Positioning, Aadesh Neel

Electrical and Computer Engineering ETDs

Global Positioning System (GPS) is an essential part of modern life but is susceptible to same frequency jamming. GPS jamming can add excessive noise to a received low power signal and have the capability to change or completely distort information being sent through the GPS signal. Adaptive antenna arrays have long since been a solution to mitigating GPS jamming via beamnulling algorithms. However, there is little research on the effectiveness of these beamnulling algorithms under varying element positioning. In this work, an adaptive antenna array, consisting of Right-Hand Circularly Polarized (RHCP) nearly square GPS antenna elements, was constructed and tested …

High Performance Scene Generator For Testing Of Imaging Sensors, Austin Modoff

Electrical Engineering Theses and Dissertations

Since the invention of modern solid-state imaging sensors in the 1980s, considerable advancements have been made, improving aspects such as frequency response, dynamic range, resolution, and wavelength diversity, as well as inventing many different types of sensor architectures such as framing sensors and event sensors. While considerable improvements in this field are evolving every day, the methods by which to test and validate these systems remain unchanged. Many of these test platforms require specialized designs to test only one or two specific qualities. For example, a spinning disk in front of a black body source to measure the frequency response …

Adaptive Plasmonic Metasurfaces For Radiative Cooling And Passive Thermoregulation, Azadeh Didari-Bader, Nooshin M. Estakhri, Nasim Mohammadi Estrakhri

Engineering Faculty Articles and Research

In this work, we investigate a class of planar photonic structures operating as passive thermoregulators. The radiative cooling process is adjusted through the incorporation of a phase change material (Vanadium Dioxide, VO₂) in conjunction with a layer of transparent conductive oxide (Aluminum-doped Zinc Oxide, AZO). VO₂ is known to undergo a phase transition from the “dielectric” phase to the “plasmonic” or “metallic” phase at a critical temperature close to 68°C. In addition, AZO shows plasmonic properties at the long-wave infrared spectrum, which, combined with VO₂, provides a rich platform to achieve low reflections across the …

High Performance Radar System, Danny Maas

Electrical Engineering

This report covers the design, fabrication, and test of an X-band FMCW radar inspired by the radars from Cal Poly course EE 541, “Advanced Microwave Laboratory.” In this class, 2.4GHz Doppler and FMCW radars are designed and built using consumer off-the-shelf (COTS) components. Operability is the focus of this class, sacrificing performance, accuracy, and precision. this project aims to improve upon those radars by using custom-designed components instead of COTS components and shifting the operating frequency to 10GHz.. The use of custom components can improve output power and frequency stability, and higher frequency reduces component size. The FCC allows amateur …

Design, Modeling, And Testing Of A Novel Inductor For Electric Vehicles: Iron Nitride Soft Magnetic Composites, Sydney F. Fultz-Waters, Jacob Krynock

Materials Engineering

New technology for electric vehicles (EVs) must meet the requirements of higher energy usage, lower costs, and more sustainable source materials. One promising material for EV power system components is iron nitride (IN) soft magnetic composites (SMCs) because of their competitive magnetic properties and high abundance of the source materials. As part of an ongoing program at Sandia National Laboratories, this project focused on using computer modeling to optimize the prototyping process for an iron nitride SMC toroidal inductor to reach a target inductance of 600 μH. Four inductors with different combinations of wiring (26 AWG and 20 AWG) and …

Photophoretic Optical Trapping, Essa Ababseh

Electrical Engineering

Photophoretic Optical Trapping (POT) is a relatively new concept in the field of optics which has potential application in 3D display. The POT is realized by confining a particle within a very small location of the optical system, mostly around the focus. The particle, if captured by the beam, has the potential to print visible 3D images in free space. Our POT system is encapsulated by an acrylic enclosure, which also incorporates a biconvex lens as well as an adjustable focus laser module. Particles are released around the top of the lens’ focal point until the captured particle can be …

Wireless Energy Harvesting System, Matthew Palma, Audrey Toop, Andrew Fahey

Electrical Engineering

The modern world is built upon wireless transmission of data. The signals that carry this data travel through the air, an untapped source of power. Unreceived transmissions are dissipated into useless forms of energy when they should be reclaimed. Wireless electronics can theoretically be powered by harvesting energy from the electromagnetic signals in the wireless internet frequency band. The aim of this project is to develop a system to capture ambient energy, convert it into DC power, and store the power for later use. The product will consist of three subsystems: an antenna receiver, a rectifier and voltage-multiplier, and a …

Sky Survey Radio Telescope, Jack E. Mcguigan

Electrical Engineering

This document outlines the design of a radio telescope designed to perform hydrogen line sky surveys. The telescope produces radio images mapping the intensity and relative velocities of hydrogen concentrations to their sky coordinates. Over the course of a day, the telescope images the regions of space visible to it, allowing sky survey imagery to be updated daily. Sky survey images are comprised of an array of pixels corresponding to specific sky coordinates. Each 8-bit RGB pixel contains information on the concentrations of hydrogen in the brightness and relative velocity in the color. Radio images mapping the concentrations and velocities …

Design Of Class F-Based Doherty Power Amplifier For S-Band Applications, Kyle Chang

Master's Theses

Modern RF and millimeter-wave communication links call for high-efficiency front end systems with high output power and high linearity to meet minimum transmission requirements. Advanced modulation techniques, such as orthogonal frequency-division multiplexing (OFDM) require a large power amplifier (PA) dynamic range due to the high peak-to-average power ratio (PAPR). This thesis provides the analysis, design, and experimental verification of a high-efficiency, high-linearity S-band Doherty power amplifier (DPA) based on the Class F PA. Traditional Class F PAs use harmonically tuned output matching networks to obtain up to 88.4% power-added efficiency (PAE) theoretically, however the amplifier experiences poor linearity performance due …

Characterization Of Low Power Hfo2 Based Switching Devices For In-Memory Computing, Aseel Zeinati

Theses

Oxide based Resistive Random Access Memory (RRAM) devices are investigated as one of the promising non-volatile memories to be used for in-memory computing that will replace the classical von Neumann architecture and reduce the power consumption. These applications required multilevel cell (MLC) characteristics that can be achieved in RRAM devices. One of the methods to achieve this analog switching behavior is by performing an optimized electrical pulse. The RRAM device structure is basically an insulator between two metals as metal-insulator-metal (MIM) structure. Where one of the primary challenges is to assign an RRAM stack with both low power consumption and …

Theory, Simulation, And Experiments On A Magnetically Insulated Transmission Line Terminated By A Bremsstrahlung Diode, Troy Clay Powell

Electrical and Computer Engineering ETDs

Foundational concepts necessary for power flow analysis of a self-magnetically insulated transmission line (MITL) are introduced in theoretical form and several developments to the theory are described. These include cold-cathode electron emission physics, self-magnetic insulation physics, self-limited MITL current, and relativistic secondary ion production from anode surfaces. Modeling these physics is performed using EMPIRE, an electromagnetic particle-in-cell code.

Self-limited MITL current theory described numerically by Pointon is developed here in analytic form and is then used to drive simulations to compare to experiments that were performed in EMPIRE. Carefully calibrated current sensors from HERMES-III experiments show good agreement with EMPIRE …

Micro-Faraday Cage Design And Analysis For Rf Sensitive Components On An Ltcc Substrate In Hfss, Roberto Quezada

Electrical Engineering Undergraduate Honors Theses

This thesis focuses on creating and testing two different simulation environments in HFSS and analyzing the effectiveness of a micro-Faraday Cage on the RF Sensitive component by exchanging the SMPS and RF Sensitive component with 25GHz Microstrip Patch Antennas. Modern integrated circuit board systems consist of components that can generate electromagnetic signals and components that may be sensitive to electromagnetic interference. A switched-mode power supply (SMPS) is one component capable of producing electromagnetic interference (EMI) through its fundamental and harmonic switching frequency. By using a Faraday Cage to shield the RF-sensitive element, it is possible to reduce its susceptibility to …

Measurements Of Magnetic Field Penetration Of Materials For Superconducting Radiofrequency Cavities, Iresha Harshani Senevirathne

Physics Theses & Dissertations

Superconducting Radio Frequency (SRF) cavities used in particle accelerators are typically formed from or coated with superconducting materials. Currently high purity niobium is the material of choice for SRF cavities which have been optimized to operate near their theoretical field limits. This brings about the need for significant R&D efforts to develop next generation superconducting materials which could outperform Nb and keep up with the demands of new accelerator facilities. To achieve high quality factors and accelerating gradients, the cavity material should be able to remain in the superconducting Meissner state under high RF magnetic field without penetration of quantized …

Multiple Output Power Supply Using Toroidal Transformers For Medium Voltage Active Gate Drivers, Samhitha Venkata Machireddy

Graduate Theses and Dissertations

When operating in high power applications, power devices dissipate tens or hundreds of watts of power in the form of heat. The ability of the power devices to withstand power and dissipation of heat across the power devices becomes a prominent requirement in designing the power converter. This challenge demands a power converter design to be more effective and consistent which factors in size, cost, weight, power density and reliability. This study aims to propose a gate driver isolated power supply design that can be used in medium voltage applications (e.g., up to 10 kV) while respecting the principle of …

Effect On Focusing Fields By Ferromagnetic Cell Cores In Linear Induction Accelerators, Cooper Guillaume

Senior Honors Theses

In the Los Alamos National Laboratories DARHT facility, there are two perpendicular linear induction accelerators, LIAs. The LIAs’ solenoids produce magnetic fields which focus the electron beam. Simultaneously, the accelerating pulse creates a magnetic field. These two field intensities act upon a ferromagnetic material in the cells to enhance magnetic flux density. Due to the nonlinearity of the material, this flux density will reach a saturation point. In turn, the magnetic field intensity of the axial solenoidal magnetic field will be affected and slightly altered. The width of the electron beam will increase, causing a decrease in effectiveness. Through simulation, …

A Study Of A Monolithic Pulsed Fiber Laser With High-Peak And Average Power, Mark Mihalik

All Theses

Fiber lasers with high peak power, pulse energy and average power have numerous industrial applications. This project aimed to build a Master Oscillator Power Amplification fiber laser using commercial components and specialty fiber designed by Clemson University to exceed the power and energy targets of a previous Q-switched fiber laser design. The specialty fiber has a low numerical aperture of 0.028 and a unique geometric core design to minimize amplified spontaneous emission and reduce nonlinear effects in order to produce a high-peak power and high per pulse energy. The two stage, monolithic design targets 3.1 mJ per pulse, average power …

Classification Of Electrical Current Used In Electroplastic Forming, Tyler Grimm

All Dissertations

Electrically assisted manufacturing (EAM) is the direct application of an electric current to a workpiece during manufacturing. This advanced manufacturing process has been shown to produce anomalous effects which extend beyond the current state of modeling of thermal influences. These purported non-thermal effects have collectively been termed electroplastic effects (EPEs).

While there is a distinct difference in results between steady-state (ideal DC) testing and pulsed current testing, the very definition of these two EAM methods has not been well established. A "long" pulse may be considered DC current; a "short" pulse may produce electroplastic effects; and even "steady-state" current shapes …

A Study On Asymmetric Perfect Vortex: Fractional Orbital Angular Momentum And Nonlinear Interaction, Kunjian Dai

All Dissertations

In this work, the manipulation including generation and detection of the asymmetric perfect vortex (APV) carrying fractional orbital angular momentum (OAM) was demonstrated and discussed. All the manipulation of the modes is in real-time which provides a perfect tool for sensing the dynamic properties of complex media. The OAM-involved nonlinear conversion, specifically the second-harmonic generation (SHG) using the APV and asymmetric Bessel-Gaussian (BG) beams was studied in detail.

The generation and detection of the APV are based on the HOBBIT concept which includes acoustic optical deflector (AOD) and log-polar coordinate transformation optics. The RF signal driving the AOD allows the …

Analysis And Application Of Finite Element And High-Order Finite Difference Methods For Maxwell’S Equations In Complex Media, Li Zhu

UNLV Theses, Dissertations, Professional Papers, and Capstones

The Perfectly Matched Layer (PML) technique is an effective tool introduced by B´erenger [13] to reduce the unbounded wave propagation problem to a bounded domain problem. This dissertation focuses on two different PML models and their applications to wave propagation problems with Maxwell’s equation in complex media. We investigate these models using two popular numerical methods: the Finite Difference Method (FDM) in Chapters 2 and 3, and the Finite Element Method (FEM) in Chapters 4 and 5.In Chapter 2, we focus on analyzing the stability of a PML developed by B’ecache et al. [10] for simulating wave propagation in the …

Evaluation Of The Dynamic Vision Sensor’S Photoreceptor Circuit For Infrared Event-Based Sensing, Zinah M. Alsaad

Electrical and Computer Engineering ETDs

For space surveillance applications, neuromorphic imaging is being studied as it may perform sensing and tracking tasks with less power and downstream datalink demand. The read-out of the event-based camera is made to only be sensitive to changes in the signals it receives from the photodetector, which results in a datastream of events indicating where and when changes in illumination occur. This is in contrast to the conventional framing camera, which produces images by essentially counting the electrons produced by light incident on each pixel’s photodetector. These cameras are commercially available with siliconbased detectors for applications involving visible wavelengths. However, …

Improved Experimental Validation Of An Electromagnetic Subcell Model For Narrow Slots With Depth, Michael Anthony Illescas

Electrical and Computer Engineering ETDs

The coupling of electromagnetic (EM) energy into a system can disrupt operation of essential electronics present within it. Metal enclosures are used to shield these systems from potentially harmful electromagnetic interference (EMI). Seams and gaps in such metal enclosures are minimized but unavoidable for reasons such as maintenance and repair. These seams and gaps create an entry point for EM energy to couple into the system. Entry points are often modeled by EM analysts as narrow slots defined by their length, width, and depth. The depth of these slots can become significant compared to the wavelength, introducing resonances associated with …

Computational Design Of Fiber-Optic Probes For Biosensing, Suwarna Karna

Electrical Engineering Theses

This thesis presents a study on the optical characteristics of hollow-core photonic crystal fibers (HC-PCFs) with a band gap cladding structure and their applications in optical fiber sensing. This 800B HC-PCF exhibited excellent optical properties and has a flexible structure, which makes them suitable for a wide range of industrial applications. Finite element simulations and structural optimization designs were conducted using the surface plasmon resonance (SPR) technique to determine the optimal performance parameters of the 800B HC-PCF. The fiber was further modified using the SPR technique to improve its practical detection capabilities. The performance of the modified fiber was observed …

Implementing Commercial Inverse Design Tools For Compact, Phase-Encoded, Plasmonic Digital Logic Devices, Michael Efseaff, Kyle Wynne, Krishna Narayan, Mark C. Harrison

Engineering Faculty Articles and Research

Numerical simulations have become an essential design tool in the field of photonics, especially for nanophotonics. In particular, 3D finite-difference-time-domain (FDTD) simulations are popular for their powerful design capabilities. Increasingly, researchers are developing or using inverse design tools to improve device footprints and performance. These tools often make use of 3D FDTD simulations and the adjoint optimization method. We implement a commercial inverse design tool with these features for several plasmonic devices that push the boundaries of the tool. We design a logic gate with complex design requirements as well as a y-splitter and waveguide crossing. With minimal code changes, …