Propulsion and Power Commons^™

A Model For Spacecraft Relative Motion Using Continuous Periodic Thrust, Philip Alan Hittepole

Dissertations

A model for modifying the relative orbit of a deputy satellite with respect to a chief satellite in a near-circular orbit using continuous periodic thrust is presented. This model is built on the Lovell-Spencer relative orbital elements (ROEs). The four linear ROEs (xr, yr, ar, and Az) can be linearly modified. The two angular ROEs (Er and ) can be set to advance at a desired, constant rate. Each ROE can be modified individually but may cause intra-orbit variations in other ROEs which return to their original values at the end of a thrust cycle. A method to easily calculate …

Rapid Response Satellite Launcher, Nathan Jones, Joey Cosentino, Jayson Layton, Afek Adar

Senior Design Project For Engineers

Air launch to orbit is a new style or spacecraft where rockets are attached to a large aircraft and released at cruising altitude to then ignite and launch into space. Companies such as Virgin Orbit are using it as a cheap and efficient way to move satellite payloads into lower or upper Earth orbit. These styles of launchers can be designed to be much smaller than ground-launched spacecraft, reducing cost and weight of the launcher in comparison. With many private companies coming into the space and satellite industry, the design and manufacturing of these launchers have become a focus within …

A Study Of Varying Dielectric Constant And Thickness Of Dielectric Barrier Discharge Devices And Their Subsequent Plasma Actuation, Sharon Kardasz

Mechanical Engineering Undergraduate Honors Theses

The principles of air-breathing ion propulsion are relatively unestablished in the aerodynamic realm as traditional forms of combustion for propulsion systems have remained in use. However, due to increasing environmental, economic, and efficiency concerns of traditional combustion, interests in innovative propulsion methodologies, such as electric propulsion, are emerging. A primary technology of interest for use of ion propulsion is the Dielectric Barrier Discharge Device (DBD). Preliminary research conducted at the University of Arkansas has determined the most favorable DBD geometry. This work will continue the preliminary research to decipher the most favorable DBD configuration by varying dielectric thickness and dielectric …

Modeling Of Rotor Wake Vortex Dynamics And Interactions In Non-Homogenous Vertiport Environments, Garrison P. Shaw

Doctoral Dissertations and Master's Theses

The current research serves to analyze and study the effects ground forces can have on the thrust performance of a propeller in multiple different configurations. The current research utilizes an open source Computational Fluid Dynamics (CFD) software known as OpenFOAM to generate calculate and visualize these runs. The model used for this experiment is a hybrid model that employs both a Unsteady Reynolds-Averaged Navier-Stokes (URANS) and a detached eddy simulation using a hybrid Large Eddy Simulation (LES) via a KomegaSSTDDES model. This model serves to save computational time as well as allow for accurate results. The three cases run are …

Development Of On-The-Fly Quasi-Steady State Approximation For Chemical Kinetics In Cfd, Abhinav Balamurugan

Doctoral Dissertations and Master's Theses

This study analyzes the feasibility of On-The-Fly Quasi-Steady-State Approximation (OTF-QSSA) application for solving chemical kinetics within Computational Fluid Dynamics (CFD) simulations, aiming to reduce the computational demand of detailed mechanisms. An algorithm that dynamically identifies and designates Quasi-Steady-State (QSS) species at specific grid locations and instances during the simulation was developed. With this information, our method pseudo-delays the advancement of concentrations for these QSS species—effectively setting their rate of concentration change to zero for a set number iteration before updating using the detailed mechanism and thereby omitting the computationally intensive processes typically required for their calculation during those skipped iteration. …

Mitigating Engine Unstart In Scramjets With Porous Bleeders, Ryan Lindley

Doctoral Dissertations and Master's Theses

The effectiveness of porous bleeders in mitigating unstart phenomena and enhancing isolator effectiveness in a hypersonic scramjet was investigated. Through computational fluid dynamics simulations, the impact of porous bleeder design parameters such as pressure jump coefficient and bleeder size on isolator effectiveness and unstart prevention was evaluated. Results indicated that porous bleeders delayed flow separation and reduced adverse pressure gradients, thereby enhancing isolator performance. Additionally, porous bleeders demonstrated promising capabilities in preventing full unstart events and mitigating oscillatory unstart phenomena.

Benchmarking Of A Sco2 Heat Exchanger Flow Loop, David Velasco

Doctoral Dissertations and Master's Theses

Heat transfer of supercritical carbon dioxide (sCO2) was studied experimentally by commissioning a sCO2 flow loop featuring a horizontal tube-in-tube counterflow heat exchanger with a circular cross section. The main objective was to establish experimental heat transfer research capabilities for sCO2 at Embry-Riddle Aeronautical University’s (ERAU) Thermal Science Lab. sCO2 experiences a drastic change in thermophysical properties near its critical point that results in unique heat transfer characteristics. The high pressures at which sCO2 exists make the large gradients in thermophysical and transport properties difficult to study, experimentally and numerically. However, understanding the heat transfer characteristics and thermophysical behavior of …

Investigation Of The Effect Of Internal Reynolds Number And Advective Capacity Ratio On Gas Turbine Film Cooling Parameters, John P. Di Lella

Theses and Dissertations

The desire for more powerful engines drives higher turbine inlet temperatures and a greater need to cool them. Experimentalists attempt to match cooling effectiveness between two conditions by matching several non-dimensional parameters, one of which is the coolant warming factor. The first investigation of this study examines the effect of the internal Reynolds number and the advective capacity ratio on the coolant warming factor by making use of a computational model and four different gases. It indicates the non-negligible and opposing effects of external convection and solid conduction on the coolant warming factor at matched internal Reynolds number and advective …

Experimental Analysis Of The Integrated High-Lift Propulsor, Robert W. Deters, Byron Ward, Shreyas Narsipur

Publications

Wind tunnel testing was conducted to evaluate the performance of the Integrated High Lift Propulsor (IHLP), a novel Distributed Electric Propulsion (DEP) system. The IHLP integrates traditional Krueger flap/slat elements with a Distributed Electric Propulsion design, enhancing high lift performance and cruise efficiency compared to conventional pylon-mounted DEP configurations. Starting from a baseline configuration determined from pretest Computational Fluid Dynamics (CFD) analyses, a parametric study was performed to determine the influence on the aerodynamic characteristics (���� , ����, and ����). The study involved variations in flap settings, slat angles, overlap, propeller tilt, and propeller position. The impact of Reynolds number, …

Development Of Advanced Instrumentation For High-Enthalpy Flow Characterization For The Onr-Uta Arc-Jet ”Leste” Facility, Ian Raybon

Mechanical and Aerospace Engineering Dissertations - Archive

Sustained hypersonic flight is an exceedingly challenging task comprised of a myriad of complex physical processes. At hypersonic speeds, which is defined by the presence of unique phenomena like high-temperature nonequilibrium flow, viscous and vorticity interactions, and thin shock layers, which are not seen in supersonic, transonic, or subsonic vehicles, the vehicle design is principally driven by the high levels of aerodynamic heating caused by the conversion of kinetic energy to internal energy. Gaining an understanding of how these physical processes interact with each other is required to develop a design methodology for this class of vehicles. Arc-jet wind tunnels …

Dynamics Of Separated Flows In Diffusers With Vortex Generators, Sandeep Eldho James

Mechanical and Aerospace Engineering Dissertations - Archive

Flow through curved diffusers is complicated due to the possibility of flow separation and secondary flows. Vortex generators (VGs) are a class of passive flow separation control devices used to improve the flow quality in curved diffusers by suppressing flow separation. However, the literature review demands an in-depth investigation on the physical mechanisms related to flow separation control. Thus, this study aims to improve the understanding of the underlying flow physics associated with VG-induced flow separation control in confined flows. The chosen geometry for this study is a well-documented asymmetric diffuser which exhibits a mild flow separation.

The theoretical formulation …

Aerothermodynamic Analysis Of A Linear Aerospike Fueled With Liquid Methane Using Cfd, Aidan Rowell

Honors College Theses

Renewed interest in manned spaceflight, mostly spurred by the advancement of commercial spacecraft, has led to growing interest in improving the efficiency of rocket engines. Aerospike nozzles have the potential to provide this boost in efficiency to spacecraft and thus lower costs and increase payload capacity. This type of nozzle is what is known as altitude adjusting and can significantly increase efficiency. When paired with propellants such as methane/oxygen, which can be manufactured in-situ on some planetary bodies and has a higher density than traditional propellants like liquid hydrogen/liquid oxygen, even more efficiency gain can be achieved. To understand the …

Design And Development Of Supersonic Free Jet Facility, Gowtham Sai Somaroutu

Mechanical and Aerospace Engineering Theses - Archive

High-speed wind tunnels are essential facilities for conducting research and testing in external and internal flows. This thesis details the design and development of a blow-down supersonic free-jet facility with a 3-inch square nozzle in the Mach number range of and unit Reynolds number ranging. Key aspects of the facility development include the detailed design of the gas supply system, control valve selection, plenum, nozzle, test section, and the selection of an exhaust silencer. CAD designs for all the components of the facility were also generated in this effort.

A new analytical approach was developed to design supersonic contoured nozzles …

Uav To Carry Heavy Loads, Jacob Cannon, Robert Connor Downs, Anthony Orlando

Williams Honors College, Honors Research Projects

Our senior design project aims to develop an innovative Unmanned Aerial Vehicle (UAV) capable of carrying heavy payloads up to 50 lbs. This UAV will address the growing demand for efficient and autonomous cargo transportation, unlocking new possibilities in logistics and remote deliveries. The primary goal is to design, build, and test a robust UAV platform equipped with advanced propulsion systems, stabilizing mechanisms, and a secure payload attachment system. The heavy-lift UAV will be capable of transporting payloads in challenging environments, enhancing its versatility for various industries, including emergency response, disaster relief, and commercial logistics. For the extent of this …

Design Of An Experimental Solid Rocket Motor, Johnathan Bettes, Andrew Fuller

Williams Honors College, Honors Research Projects

This project utilizes mechanical and chemical principles to characterize propellant grains and to manufacture a custom nozzle to create experimental Solid Rocket Motors (SRMs) with a propellant called Angry Listerine. For the propellant grains, one major non-chemical factor that determines its thrust performance is the grain geometry, or the core of the grains for which hot gases flow through the propellant and out of the nozzle to further react with exposed chemical surfaces. The two kinds of grain geometries analyzed and tested in this report are called MoonBurner, an offset circular core, and Finocyl, a gear-shaped core. The nozzle for …

Optimization Of High-Bypass Turbofan High-Pressure Compressor Blade – A Case Study, Adeel Khalid, Vlad Mandzyuk

The Kennesaw Journal of Undergraduate Research

This research determines the relationship between the High-Pressure Compressor (HPC) rotor blade design variables and compressor pressure ratio of a high bypass turbofan engine. Alterations in the HPC blades span, chord, taper, twist, number, and angle of incidence are performed and their effect on the HPC pressure ratio is observed. The objective is to determine key parameters that could maximize the performance of a high-pressure compressor for a given mission. Physics-based modeling, Computational Fluid Dynamics (CFD), and wind-tunnel testing are performed to compare and validate findings. Physics-based modeling is performed to serve as the benchmark for data obtained through other …

Propulsion Heat Analysis Nuclear Trajectory Optimization (Phantom), Ana Clecia Alves Almeida, Jonathan Davis, Ryan Dippolito

Williams Honors College, Honors Research Projects

Interplanetary Travel requirements necessitate the use of increasingly complex propulsion systems. Nuclear Thermal Propulsion (NTP) is a cutting-edge concept that holds immense potential for the future of space exploration. By utilizing nuclear fission to heat a propellant and generate thrust, NTP offers the potential for unprecedented efficiency, enabling faster interplanetary travel and extended mission capabilities. A nuclear thermal rocket engine is a type of propulsion system that utilizes the heat generated by a nuclear reactor to heat and expel a propellant, typically hydrogen, at high velocities to produce thrust. The engine consists of three main subsystems: the nuclear reactor, the …

Analysis Of Variations In Flow-Independent Liquid Jet-In-Crossflow Injections, Michael Scott

Honors Undergraduate Theses

Liquid fuel injection is a critical mechanism for the deliverance of liquid fuel in contemporary aircraft propulsion combustion systems due to its outsized influence in providing optimal combustion conditions and improving overall aircraft efficiency and performance. Despite this, these liquid jet in crossflow (LJIC) systems are highly variable due to conditions in the jet and the surrounding airflow, leading to variability in performance behavior and inconsistency in fuel mixing and combustion efficiency. This has prompted the introduction of solid pintile obstructions of novel designs to provide a more flow-independent fuel injection scheme and decrease variability of the jet properties against …

Investigations Of Performance And Emissions Of A Fischer-Tropsch Gtl Sustainable Aerospace Fuel With Lubricity Improver In A Compression Ignition Engine With Butanol Port Fuel Injection, James B. Willis

College of Graduate Studies: Theses & Dissertations

As there is increasing concern over emissions of traditional fossil fuels, as well as the future of continued reliance on this dwindling resource, it is becoming increasingly evident that alternative fuels are a necessity. This research investigates the use of a Fischer-Tropsch fuel from natural gas feedstocks, S8, in an internal combustion research engine with a common rail fuel injection system. This synthetic kerosene fuel has a high DCN of 62, indicating high affinity to autoignition compared to conventional pump diesel (ULSD) at 48 DCN. However, due to the process by which it is produced, this fuel lacks the necessary …

Experimentatal And Numerical Investigation Of Turbojet Engine Performance, Emissions, And Noise/Vibrations Using Jet-A And F24 Fuel, John W. Mcafee Jr

College of Graduate Studies: Theses & Dissertations

Drastic improvement in cost effectiveness of high-power computing resources has generated a great interest numerical simulation to reduce the overhead cost of engine manufacturing, maintenance, and environmental concerns of engine testing. To accomplish this goal, this research presents the differences between military F24 fuel and commercial aviation fuel Jet-A from a thermochemical and engine performance perspective. This experimental data was used to create and validate a numerical model of the engine used in the experiments fueled with both Jet-A and F24 fuels. The experimental data was collected using a research based single stage turbojet engine outfitted with many sensors for …

Simulation Of Reacting Supersonic Flow In A Cavity Flameholder, Mohamed Benjelloun Touimi

Electronic Theses and Dissertations

Scramjet engines, or Supersonic Combustion Ramjets, are pivotal for achieving and maintaining hypersonic flight speeds. These engines leverage the high-speed airflow to compress and mix air and fuel for combustion. A significant challenge in Scramjet engine design is ensuring stable and efficient combustion within this high-speed environment. Cavity flameholders are crucial components that stabilize the combustion process by creating a subsonic region where the fuel-air mixture can ignite and sustain combustion. This research simulates this supersonic flow within the combustion chamber to accurately model and analyze the combustion dynamics. Various turbulence models, including RANS, and DES, are evaluated for their …

Comparative Evaluation Of Propulsive Power Transmission Technologies For High-Speed Vertical Takeoff And Landing (Hsvtol) Cargo Aircraft, Xinyu Yang

Doctoral Dissertations and Master's Theses

Designing High-Speed Vertical Takeoff and Landing (HSVTOL) cargo aircraft capable of both low downwash velocity hovering and high subsonic speed cruising presents a significant engineering challenge. This challenge, stemming from conflicting design requirements, has been substantially influenced by recent technological advancements, which have offered greater flexibility in rotor placement. Consequently, this has led to the emergence of innovative mission-specific designs that hold the potential to outperform traditional concepts. The central objective of this study is to evaluate the benefits of modern technologies for VTOL cargo aircraft and assess their performance relative to baseline VTOL aircraft. The results of this comparative …

2023 Summer-Fall Graduate Recognition Program, Propulsion Research Center, Robert Frederick

PRC Graduate Recognition

This program includes the graduate recognition program for summer and fall 2023. Includes photographs, upcoming events, recent publications, and student profiles.

Testing And Implementation Of Attitude Determination & Control System For Arksat-1 Cubesatellite, Cassandra Sands

Graduate Theses and Dissertations

ARKSAT-1 is a CubeSatellite (CubeSat) developed at the University of Arkansas and launched to the International Space Station on SpaceX mission SPX-27 launching from Kennedy Space Center as part of the NASA’s 8th CubeSat Launch Initiative CSLI-8. ARKSAT-1’s payload features a high-powered LED, the Solid State Inflatable Balloon (SSIB) deorbiting system applicable to small satellites, and a series of InfraRed and Visible cameras. To point the LED or take images of desired observational targets, the spacecraft will need to be able to determine its orientation within its orbit, as well as rotate. This will be achieved through the use of …

Kwad - Ksu All Weather Autonomous Drone, Nick Farinacci, Sebastian Gomez, Stewart Baker, Ed Sheridan

Symposium of Student Scholars

"KWAD" or "KSU all-Weather Autonomous Drone" project was sponsored by Ultool, LLC to the KSU Research and Service Foundation to create a lightweight drone capable of capturing HD video during all-weather operations. The conditions of all-weather operation include rainfall of one inch per hour and wind speeds of up to twenty miles per hour. In addition, a global minimum structural safety factor of two is required to ensure the system's integrity in extreme weather conditions. Potential mission profiles include autonomous aerial delivery, topological mapping in high moisture areas, security surveillance, search and rescue operations, emergency transportation of medical supplies, and …

Development, Implementation, And Evaluation Of Swirl-Combustion Strategies For Optimal Performance Of Ammonia As A Fuel For Gas Turbine Engines, Varun Nanjunda Rao Viswamithra

LSU Doctoral Dissertations

In an effort to reduce harmful effects of greenhouse gas emissions, ammonia is being pursued as a fuel for power generation as it is a carbon-free energy source. However, the use of ammonia-air mixtures in premixed swirl combustors poses challenges due to low flame speed and reactivity resulting in combustor stability issues in addition to high Nitrous Oxide (NOx) emissions due to the presence of fuel-bound Nitrogen. The first part of this study attempts to overcome lean blowout limits of methane-ammonia-air mixtures using a novel, multi-point () injection strategy, whereby micron-sized holes on the swirler vanes generate a co-flowing stream …

Performance And Emissions Study Of N+3 And N+4 Engine Models With Several Fuel Types Using Npss, Abel Solomon

McKelvey School of Engineering Graduate Student Theses & Dissertations

The aviation industry is known to be one of the major contributors to greenhouse gases accounting for 4.9% of the global greenhouse emissions. With the ever-increasing threat of climate change to the overall survival of the planet, the exploration of new technologies and alternative energy sources that minimize greenhouse gas emissions are of paramount importance. In this regard, the development of propulsion systems well suited for the performance and emissions requirements of future commercial aircraft plays a crucial role. This thesis investigates N+3 and N+4 technology-level propulsion systems that are proposed by NASA as possible propulsion systems for advanced single-aisle …

Design And Implementation Of A Launching Method For Free To Oscillate Dynamic Stability Testing, Kristen M. Carey

Mechanical & Aerospace Engineering Theses & Dissertations

Magnetic Suspension and Balance Systems (MSBS) allow for static, forced oscillation and free to oscillate dynamic stability testing in a wind tunnel without the need for a physical support. The objectives of study are to assist in the application of the free to oscillate testing method in an MSBS to determine dynamic stability characteristics for various re-entry capsule designs.

This thesis discusses the development and testing of a launching method called the grabber for use in the MSBS Subsonic Wind Tunnel at NASA Langley Research Center. Aerodynamic tests were run to support the use of this method and compare the …

Performance Evaluation And Thermal Management Solutions For A Sustainable Microsized Hydrogen-Powered Turbo-Shaft Engine, Nikolai Baranov

Discovery Undergraduate Interdisciplinary Research Internship

Analyzing the aerospace and automotive industries, there is a transition to sustainable energy generation. Aiming to bridge industrial emissions with the worldwide net zero goal by 2050, one widely considered solution for long-range drones and small aircraft is compact turbo-shaft engines combusting clean hydrogen gas to produce shaft work. The small size and energy-dense fuel allow for a universal powerplant with high specific power output that fits a wide variety of existing solutions. One such micro-sized turboshaft internal combustion engine was created to test the potential power output, thermal management, and combustor optimization of the existing stainless steel assembly. The …

The Influence Of Mixing Duct Length And Phase Of Flight On Wall Temperatures Of A Rocket Based Combined Cycle Engine In Ejector And Air-Augmented Modes, Jonathan Grow

Doctoral Dissertations and Master's Theses

Rocket Based Combined Cycle (RBCC) engines have been theorized as a possible means of powering launch vehicles and high-speed atmospheric vehicles. By incorporating aspects of both air-breathing and rocket propulsion, RBCC engines promise up to a 230 % increase in specific impulse over traditional chemical rocket propulsion by entraining a secondary flow of atmospheric air and mixing it with the exhaust of a rocket motor. Students within the Embry-Riddle Future Space Explorers and Developers Society (ERFSEDS) identified a
problem of excessive heating and structural failure of the mixing duct during launch and transonic flight of a student-built flight test vehicle. …