Propulsion and Power Commons^™

Measurements And Scaling Of Ion Propulsion Impulse During Driven Magnetic Reconnection, Fatima Ebrahimi, Nicholas A. O'Gorman, Kush Maheshwari, Jongsoo Yoo, Alexandre Sainterme, Hantao Ji

Faculty Publications

Impulse scaling during magnetic reconnection, the magnetic energy conversion to kinetic energy, via direct Mach probe measurements in Magnetic Reconnection Experiment is examined. Ion exhaust velocity and impulse scalings with reconnecting magnetic field during the push phase of driven reconnection are presented. The outflows and impulse measurements are compared with global MHD simulations. Both measurements and simulations reveal a favorable scaling, greater than linear, of impulse with reconnecting field. These scaling results establish that magnetic reconnection could be utilized for plasma propulsion.

Nazi Weapons: Bad People, Good Technology, Fabian Grabski

Undergraduate Research Symposium

This project explores the integration and historical significance of three iconic World War II-era German weapons: the V-2 rocket, the STG-44, and the MG-42. Each of these weapons helped revolutionized military technology in its own right, reshaping the battlefield dynamics and influencing future weapon design. The V-2 rocket, as one of the first long-range guided missiles, marked the dawn of modern missile technology, while the STG-44 is recognized as a precursor to the modern assault rifle, blending the characteristics of both submachine guns and rifles. The MG-42, with its high rate of fire and advanced design, set the standard for …

Life And Performance Improvement Trenches, Thomas J. Praisner, John R. Farris, Connor Wiese

AFIT Patents

A blade outer air seal assembly includes a plurality of seal segments circumferentially disposed about an array of blades rotatable about an axis, each of the plurality of seal segments having a radially inner surface facing a tip of each blade of the array of blades, the radially inner surface having an arrangement of trenches formed therein, and a radially outer surface opposite the radially inner surface. The arrangement of trenches is disposed between 30% and 80% of a chord of a blade of the array of blades as taken at the respective tip, and the arrangement of trenches is …

Seal For A Wave Rotor Disk Engine, Christopher Tait, Pejman Abkari, Brian Sell, Marc D. Polanka

AFIT Patents

A unique seal for a wave rotor disk engine is disclosed herein. The seal is operable for sealing a region between a rotor and a rotor casing. The seal is spring loaded and will engage with the tip of the rotor to reduce pressure loss within the wave rotor disk engine.

Functional Visualizations Of A Hydrogen-Electric Aircraft Propulsion System For Supporting Pilot Decision-Making, Misha M. S. Schweitzer, Ece Üreten, Clark Borst, Olaf Stroosma, Rene Van Paassen

International Symposium on Aviation Psychology - 2025

Cognitive Work Analysis (CWA) and Ecological Interface Design (EID) were used todesign a novel flight deck display for a regional turboprop aircraft that is being retrofitted with aHydrogen Aircraft Powertrain Storage System (HAPSS). This research addresses the challengesof managing cognitive complexity in next-generation aviation systems, focusing on designinginterfaces based on system constraints which are modeled through the Abstraction Hierarchy(AH). Visualizations were discussed in interviews with subject matter experts highlighting theneed for further matching the mental model of the pilot by addressing simplicity, workload, anduse case representations on the display. The iterative process included static and dynamic displaytesting and focused on …

Hydrogen Standards And Aviation Sustainability, Eva Maleviti, Evan Stamoulis, Elen Paraschi

Publications

Standards from ISO, SAE, and ASTM are essential for certification, safety, and sustainability validation.

Hydrogen Readiness In Aviation & Challenges- Technology Meets Regulation And Market Demand, Eva Maleviti

Publications

Where technology meets regulation and market demand.

The Space Rescue Professional: Operationalizing Guardians For The Future, Benjamin Johnis, Robert Bettinger, James Dean

Faculty Publications

The escalating competition in space exploration demands a dedicated space rescue capability. This article argues for the establishment of a space rescue professional (SRP) career field within the Department of Defense and the US Space Force. By harnessing existing US Air Force combat rescue expertise and partnering with the National Aeronautics and Space Administration, the Space Force can rapidly develop a robust SRP program with the warrant officer corps as its backbone. This article addresses a critical gap in national space policy to outline a cost-effective dual-service training pipeline and SRP operational roles. Such an investment safeguards astronauts, bolsters US …

The Impact Of Film Cooling On The Heat Release Within A Rotating Detonation Combustor, Shreyas Ramanagar Sridhara, Antonio Andreini, Marc D. Polanka, Myles D. Bohon

Faculty Publications

Rotating detonation combustors establish a detonation wave that continuously circulates inside a small annulus. The presence of the detonation wave and the downstream oblique shock within the small annulus coupled with high mass flow induces a high heat load to the combustor wall. Preliminary analysis shows that for higher thermal power, internal air cooling alone is not sufficient to remove the heat out of the walls to maintain them below the maximum temperature of the metal. A possible solution is to use film cooling to reduce the heat flux to the combustor walls. One issue, though, is that the introduction …

Sunrise Propulsion Subsystem Leak Rate Measurement Methodology, Alex Kirkman, Brittany Woytko, Holly Walen, Bret Maughan

Space Dynamics Laboratory Publications

As part of the integration and testing for Sun Radio Interferometer Space Experiment (SunRISE), it was necessary to characterize the propellent leak rate of the fully assembled propulsion subsystem for each satellite to ensure compliance with performance requirements. SunRISE utilized a cold gas system for its propulsion subsystem, using R-236fa propellant inside a tank made from a monolithic 3D printed SLA material. It was not possible to accurately characterize the propellent leak rate via weight by measuring the mass loss from the tank. This is due to the SLA material having both a high absorbance rate of water in normal …

Spacecraft Attitude Control Simulator, Bricen S. Rigby

College of Engineering Summer Undergraduate Research Program

The Spacecraft Attitude Control Simulator is a single-axis attitude control platform which is intended to recreate the frictionless space environment in order to test cold-gas thruster control schemes. The overall goal of this research project was to observe settling data from the platform and compare it to simulated data. In practice, the predicted settling time was only 7% larger than observed settling time.

Cryogenic Fuel Applications To Sustainable Commercial Aircraft, Jack R. Kisling, Lillian Panning

College of Engineering Summer Undergraduate Research Program

Finding a source of clean and renewable energy is one of the greatest challenges humanity will face in the 21st century. With populations expanding, developing countries increasing their use of resources, and the rapid and alarming effects of climate change, a shift to a sustainable future is an existential prospect.

The goal of our project is to take the first steps toward getting safety procedures and lab space established, so mechanical engineering senior projects can quickly begin to experiment with cryogenic fuels. They will explore the application of cryogenic fuels to commercial aviation.

Disk Engine With Circumferential Swirl Radial Combustor, Brian T. Bohan, Marc D. Polanka, Bennett Staton

AFIT Patents

A disk engine and system configured to provide high power at a reduced axial length is disclosed herein. The disk engine includes a radial compressor, a compressor discharge manifold positioned circumferentially about compressor, a combustion chamber positioned within the discharge manifold and a radial turbine positioned radially inward of the combustion chamber.

Experimental Analysis Of The Integrated High-Lift Propulsor, Robert W. Deters, Byron Ward, Shreyas Narsipur

Publications

Wind tunnel testing was conducted to evaluate the performance of the Integrated High Lift Propulsor (IHLP), a novel Distributed Electric Propulsion (DEP) system. The IHLP integrates traditional Krueger flap/slat elements with a Distributed Electric Propulsion design, enhancing high lift performance and cruise efficiency compared to conventional pylon-mounted DEP configurations. Starting from a baseline configuration determined from pretest Computational Fluid Dynamics (CFD) analyses, a parametric study was performed to determine the influence on the aerodynamic characteristics (���� , ����, and ����). The study involved variations in flap settings, slat angles, overlap, propeller tilt, and propeller position. The impact of Reynolds number, …

Performance Evaluation And Thermal Management Solutions For A Sustainable Microsized Hydrogen-Powered Turbo-Shaft Engine, Nikolai Baranov

Discovery Undergraduate Interdisciplinary Research Internship

Analyzing the aerospace and automotive industries, there is a transition to sustainable energy generation. Aiming to bridge industrial emissions with the worldwide net zero goal by 2050, one widely considered solution for long-range drones and small aircraft is compact turbo-shaft engines combusting clean hydrogen gas to produce shaft work. The small size and energy-dense fuel allow for a universal powerplant with high specific power output that fits a wide variety of existing solutions. One such micro-sized turboshaft internal combustion engine was created to test the potential power output, thermal management, and combustor optimization of the existing stainless steel assembly. The …

Comparisons Of Cooling Performance And Flow Characteristics Of A Combustor Liner Plate With Compound Angle And Simple Angle Effusion Holes, Hwabhin Kwon, Phillip M. Ligrani, Sneha R. Vanga, Heesung Park

PRC-Affiliated Research

The present investigation considers a unique compound angle arrangement, never previously considered, with α = 30°, β = ±30°, such that the compound angle of the effusion holes changes from β = +30° to β = −30°, as adjacent rows of effusion holes are encountered. Also provided are data for comparison from a simple angle configuration with α = 30°, β = 0°. Coolant is supplied to both effusion hole arrays using arrays of impingement cooling jets. The results of the numerical simulations are obtained using the ANSYS FLUENT V 21.1 numerical code, with a shear stress transport (SST) k–ω …

Solar Sailing Adaptive Control Using Integral Concurrent Learning For Solar Flux Estimation, Luis Enrique Mendoza Zambrano, Riccardo Bevilacqua

Student Works

In the interest of exploiting natural forces for propellant-less spacecraft missions, this investigation proposes an adaptive control strategy to account for unknown parameters in the dynamic modeling of a reflectivity-controlled solar sail spacecraft. A Lyapunov-based control law along with integral concurrent learning is suggested to accomplish and prove global exponential tracking of the estimated parameters and states of interest, without satisfying the common persistence of excitation condition, which in most nonlinear systems cannot be guaranteed a priori. This involves estimating the solar flux or irradiance from the Sun to account for uncertainty and variation over time in this value. To …

Dual Quaternion Relative Dynamics For Gravity Recovery Missions, Ryan Kinzie, Riccardo Bevilacqua, Seo Dongeun

Student Works

A dual quaternion modeling approach is compared to traditional modeling methods for formation flying spacecraft utilized for gravity recovery missions. A modeling method that has traditionally been used for gravity recovery missions is presented which models the motion of two formation flying spacecraft and a test mass. This is followed by the dual quaternion-based formulation for the equations of motion of the twelve degree-of-freedom coupled relative dynamics of formation flying spacecraft and a test mass. Lastly, utilizing data products from the Gravity Recovery and Climate Experiment Follow-On mission, a comparison of these two modeling methods is presented which proves the …

Spacecraft Systems & Navigation, Christopher Vanacore

Student Works

This textbook is steered towards higher educational course entailed in Commercial Space Operations. This textbook will be covering in detail Orbital Satellites, and Spacecraft. These topics are discussed according to their application, design, and environment. The power system, shielding and communication systems are reviewed along with their missions, space, environment and limitations. Any vehicle, whether manned or unmanned, intended for space travel is a spacecraft. A spacecraft's required systems and equipment depend on the information it will acquire and the tasks it will perform. Although their levels of sophistication vary widely, they re all subject to the harsh conditions of …

Seal For A Wave Rotor Disk Engine, Christopher Tait, Pejman Akbari, Brian Sell, Marc D. Polanka

AFIT Patents

A unique seal for a wave rotor disk engine is disclosed herein. The seal is operable for sealing a region between a rotor and a rotor casing. The seal is spring loaded and will engage with the tip of the rotor to reduce pressure loss within the wave rotor disk engine.

Impulse Measurement Methods For Pulsed Laser Ablation Propulsion, Ishaan Mishra, Scott Kirkpatrick

Rose-Hulman Undergraduate Research Publications

Pulsed laser ablation propulsion has the potential to revolutionize space exploration by eliminating the requirement of a spacecraft to carry its propellant and power source as the high-power laser is situated off-board. More experimentation needs to be done to optimize this propulsion system and understand the mechanisms of thrust generation. There are many methods used to calculate the impulse imparted in pulsed laser ablation experiments. In this paper, key performance parameters are derived for some of the impulse measurement methods used in ablation propulsion experiments. Regimes discussed include the torsional pendulum system, simple pendulum system, and solid and liquid microspheres.

A Comparative Performance Analysis Of The Novel Turboaux Engine With A Turbojet Engine, And A Low-Bypass Ratio Turbofan Engine With An Afterburner, Kaleab Fetahi, Sharanabasaweshwara A. Asundi, Arthur C. Taylor

Mechanical & Aerospace Engineering Faculty Publications

Presented herein is a comparative performance analysis of a novel turbofan engine with an auxiliary combustion chamber, nicknamed the TurboAux engine, against a turbojet engine, and a low bypass ratio turbofan engine with an afterburner is presented. The TurboAux engine is an adaption of the low-bypass ratio turbofan engine, but with secondary combustion in an auxiliary bypass annular combustion chamber for thrust augmentation. The TurboAux engine is envisioned with the desire to facilitate clean secondary burning of fuel at temperatures higher than in the main combustion chamber with air exiting the low-pressure compressor. The comparative study starts by analyzing the …

Feasibility Of Low-Enriched Uranium Fueled Nuclear Thermal Propulsion In The Low-Thrust Region Below 16klbf, Samantha B. Rawlins, Dale L. Thomas

PRC-Affiliated Research

No abstract provided.

Turbine Cooling System With Energy Separation, James L. Rutledge, Matthew Fuqua, Carol M. Bryant

AFIT Patents

A method and system for cooling an engine and/or vehicle using energy separation is disclosed herein. An energy separation device is operable for separating a compressed gaseous coolant stream into a first relatively cooler coolant flow stream and a second relatively hotter coolant flow stream. The relative cooler coolant flow stream is directed to a first region requiring increased cooling and the relative hotter coolant flow stream is directed to a second region requiring lower cooling than the first region in the engine or vehicle.

Disk Engine With Circumferential Swirl Radial Combustor, Brian Bohan, Marc Polanka, Bennett Staton

AFIT Patents

A disk engine and system configured to provide high power at a reduced axial length is disclosed herein. The disk engine includes a radial compressor, a compressor discharge manifold positioned circumferentially about compressor, a combustion chamber positioned within the discharge manifold and a radial turbine positioned radially inward of the combustion chamber.

Understanding The Nonlinear Dynamics Governing Vertical-Lift Vehicles With Variable-Speed, Fixed Rotors, Stephanie Vavra, Micah Busboom, Aleea Stanford, Keegan Moore

UNL Student Research Days Posters, Undergraduate

Problem: Traffic significantly limits travel in urban areas. • The NASA Urban Air Mobility Project is developing an air taxi as an alternative mean of transportation (Fig. 1).

Challenge: Operating rotors at different frequencies may cause the cabin to vibrate at high amplitudes. Such effects are currently unknown.

Objective: Understand the effect of variable speed rotors on passenger comfort.

From the reduced-order modeling simulations, it can be assumed that counteracting the rotor speed in-balances can reduce the displacement and vibrations experienced at the center of the wing. In other words, should a rotor not maintain its optimal operation speed, reducing …

Flow And Heat Transfer Characteristics In A Pre-Swirl Rotor-Stator Cavity, Xiaoyu Yang, Zhong Ren, Jing Ren, Philip M. Ligrani

PRC-Affiliated Research

The present study investigates flow and heat transfer characteristics in a rotor-stator pre-swirl system. Considered are rotational Reynolds numbers ReФ ranging from 3.4 × 105 to 6.8 × 105, with jet Reynolds numbers Rew of approximately 8.8 × 104 to 3.81 × 105, and associated turbulent flow parameter λT = Cw/ReФ0.8 varying from 0 to 0.4. Experimentally-measured and numerically-predicted results illustrate the combined and separate influences of jet impingement and rotor entrainment, as they affect and govern flow and heat transfer characteristics within the cavity. These results show that the relative strength of the two effects varies with ReФ and …

Small Hall Effect Thruster With 3d Printed Discharge Channel: Design And Thrust Measurements, Ethan P. Hopping, Wensheng Huang, Kunning G. Xu

PRC-Affiliated Research

Citation: Hopping, E.P.; Huang, W.; Xu, K.G. Small Hall Effect Thruster with 3D Printed Discharge Channel: Design and Thrust Measurements. Aerospace 2021, 8, 227. https:// Abstract: This paper presents the design and performance of the UAH-78AM, a low-power small Hall effect thruster. The goal of this work is to assess the feasibility of using low-cost 3D printing to create functioning Hall thrusters, and study how 3D printing can expand the design space. The thruster features a 3D printed discharge channel with embedded propellant distributor. Multiple materials were tested including ABS, ULTEM, and glazed ceramic. Thrust measurements were obtained at the …

Small Hall Effect Thruster With 3d Printed Discharge Channel: Design And Thrust Measurements, Ethan P. Hopping, Wensheng Huang, Kunning G. Xu

PRC-Affiliated Research

Citation: Hopping, E.P.; Huang, W.; Xu, K.G. Small Hall Effect Thruster with 3D Printed Discharge Channel: Design and Thrust Measurements. Aerospace 2021, 8, 227. https:// Abstract: This paper presents the design and performance of the UAH-78AM, a low-power small Hall effect thruster. The goal of this work is to assess the feasibility of using low-cost 3D printing to create functioning Hall thrusters, and study how 3D printing can expand the design space. The thruster features a 3D printed discharge channel with embedded propellant distributor. Multiple materials were tested including ABS, ULTEM, and glazed ceramic. Thrust measurements were obtained at the …

Thermochemistry Of Combustion In Polyvinyl Alcohol + Hydroxylammonium Nitrate, James K. Baird, Robert A. Frederick Jr.

PRC-Affiliated Research

A mixture of polyvinyl alcohol (PVA) and hydroxylammoniun nitrate (HAN) forms a gummy solid known as a plastisol, which is ionically conducting. When an electrostatic potential of 200 V DC is applied across the plastisol, it ignites. Combustion ceases upon removal of the applied voltage. The products of PVA + HAN combustion are known to include the molecular gases carbon monoxide, carbon dioxide, water, nitrogen, and hydrogen. When the electric field within the plastisol is spatially uniform, combustion occurs preferentially at the anode. The fact that HAN is an ionic conductor suggests that the mechanism of combustion is electrolytic in …