Propulsion and Power Commons^™

Aerodynamic Design And Structural Evaluation Of A Global Minimum Torque Inspired Multirotor Propeller, Zeke Bukovansky

Master's Theses

This thesis develops a repeatable design, CAD, aerodynamic postprocessing, structural screening, and manufacturing feasibility workflow for a 22-inch global minimum torque inspired multirotor propeller. Matched MIL and GMT geometries were compared at a 35 N, 4000 rpm static-hover operating condition using BEMT/XFOIL aerodynamic postprocessing, with diameter, blade count, chord distribution, airfoil schedule, and target thrust held constant. The final modeled comparison predicted a modest 1.5% reduction in torque and shaft power for the GMT case while maintaining the same thrust target. CAD construction, MATLAB reduced-order beam model, Abaqus screening, and manufacturing planning were used to identify geometry level structural and …

Effect Of Nozzle Pressure Ratio On Thrust And Flow Behavior In A Supersonic De Laval Nozzle, Esha Jain

Doctoral Dissertations and Master's Theses

Supersonic nozzles operate across a range of flow regimes. While an ideally expanded condition yields optimal thrust, practical propulsion systems rarely operate at this design point due to variations in altitude and engine operating conditions. As a result, nozzles frequently operate in off-design conditions. In overexpanded regime, where the exit pressure is lower than the ambient pressure, shock-induced separation may occur within the divergent section of the nozzle, potentially degrading nozzle performance. Understanding the aerodynamic behavior of nozzles operating under off-design conditions is therefore important for improving propulsion system performance and stability. In particular, direct thrust measurements provide a key …

Model-Based Design Of Compressed Lithium-Metal Pouch Cell Battery Modules For Evtol Applications, Scott J. Stirling

Master's Theses

Batteries with higher specific energy and power are essential for extending the range and performance of electric vertical takeoff and landing aircraft (eVTOLs). Anode-free lithium-metal pouch cells offer strong potential at the cell-level but require high compressive pressures to enhance cycle life and discharge performance. These pressures necessitate heavier structural components, reducing packaging efficiency at the module level.

To evaluate this tradeoff, a full-factorial enumeration model was developed to explore viable module designs within a constrained packaging volume. The model scales subsystem masses, enforces design rules and material limits, and accounts for large (~20%) cell thickness changes during cycling.

Results …

Simulation-To-Hardware Validation Of Mpc For Binary Thruster 2d Cubesat Control, Aevar Amundinusarson Oefjoerd

Theses and Dissertations--Mechanical and Aerospace Engineering

Small satellites must execute precise, fuel-limited maneuvers under strict actuation and operational constraints. Model Predictive Control (MPC) is a suitable approach because it optimizes future actions while explicitly enforcing these limits. This work evaluates (1) whether MPC can operate in real time using binary (on/off), asymmetric thrusters, and (2) whether a high-fidelity digital twin can be used to tune and validate the controller prior to hardware testing.

An MPC framework was implemented on a planar satellite prototype that floats on air bearings, operates at 16.7 Hz (60 ms period), and uses eight binary thrusters exhibiting up to 13.2% variation in …

Design Of An Experimental Solid Rocket Motor, Johnathan Bettes, Andrew Fuller

Williams Honors College, Honors Research Projects

This project utilizes mechanical and chemical principles to characterize propellant grains and to manufacture a custom nozzle to create experimental Solid Rocket Motors (SRMs) with a propellant called Angry Listerine. For the propellant grains, one major non-chemical factor that determines its thrust performance is the grain geometry, or the core of the grains for which hot gases flow through the propellant and out of the nozzle to further react with exposed chemical surfaces. The two kinds of grain geometries analyzed and tested in this report are called MoonBurner, an offset circular core, and Finocyl, a gear-shaped core. The nozzle for …

Optimization Of High-Bypass Turbofan High-Pressure Compressor Blade – A Case Study, Adeel Khalid, Vlad Mandzyuk

The Kennesaw Journal of Undergraduate Research

This research determines the relationship between the High-Pressure Compressor (HPC) rotor blade design variables and compressor pressure ratio of a high bypass turbofan engine. Alterations in the HPC blades span, chord, taper, twist, number, and angle of incidence are performed and their effect on the HPC pressure ratio is observed. The objective is to determine key parameters that could maximize the performance of a high-pressure compressor for a given mission. Physics-based modeling, Computational Fluid Dynamics (CFD), and wind-tunnel testing are performed to compare and validate findings. Physics-based modeling is performed to serve as the benchmark for data obtained through other …

Experimentatal And Numerical Investigation Of Turbojet Engine Performance, Emissions, And Noise/Vibrations Using Jet-A And F24 Fuel, John W. Mcafee Jr

College of Graduate Studies: Theses & Dissertations

Drastic improvement in cost effectiveness of high-power computing resources has generated a great interest numerical simulation to reduce the overhead cost of engine manufacturing, maintenance, and environmental concerns of engine testing. To accomplish this goal, this research presents the differences between military F24 fuel and commercial aviation fuel Jet-A from a thermochemical and engine performance perspective. This experimental data was used to create and validate a numerical model of the engine used in the experiments fueled with both Jet-A and F24 fuels. The experimental data was collected using a research based single stage turbojet engine outfitted with many sensors for …

Kwad - Ksu All Weather Autonomous Drone, Nick Farinacci, Sebastian Gomez, Stewart Baker, Ed Sheridan

Symposium of Student Scholars

"KWAD" or "KSU all-Weather Autonomous Drone" project was sponsored by Ultool, LLC to the KSU Research and Service Foundation to create a lightweight drone capable of capturing HD video during all-weather operations. The conditions of all-weather operation include rainfall of one inch per hour and wind speeds of up to twenty miles per hour. In addition, a global minimum structural safety factor of two is required to ensure the system's integrity in extreme weather conditions. Potential mission profiles include autonomous aerial delivery, topological mapping in high moisture areas, security surveillance, search and rescue operations, emergency transportation of medical supplies, and …

Cfd And Heat Transfer Analysis Of Rocket Cooling Techniques On An Aerospike Nozzle, Geoffrey Sullivan

College of Graduate Studies: Theses & Dissertations

In recent years the development of rocket engines has been mainly focused on improving the engine cycle and creating new fuels. Rocket nozzle design has not been changed since the late 1960s. Recent needs for reliable and reusable rockets, as well as advancements in additive manufacturing, have brought new interest into the aerospike nozzle concept. This nozzle is a type of altitude adjusting nozzle that is up to 90% more efficient than bell nozzles at low altitudes and spends up to 30% less fuel. Since the nozzle body is submerged in the hot exhaust gasses it is difficult to keep …

Generation Of Premix Laminar Flame Speed Library, Sai Prashanth Kumar

Dissertations, Master's Theses and Master's Reports

The Laminar flame speed is an essential parameter in measuring turbulent premixed combustion applied in Spark ignition engines. Instead of using power-law correlations, which is valid only for particular ranges, the procedure for generating a premixed laminar flame speed library is defined using MTU – Master mechanism for a wide range of charge mixture conditions inside an engine combustion chamber: Temperature (300 – 700 K), Pressure (1 – 70 bar) and reactant mixture composition of equivalence ratio (0.4 – 2.0) Laminar flame speed library is generated for methane. The mechanism's performance was improved by adjusting the pre-exponential factor of the …

Rocket Motor Nozzle, Corey Hillegass

Williams Honors College, Honors Research Projects

For this honors research and senior design project, the authors will research, analyze, and manufacture a rocket motor nozzle for the Akronauts rocket design team. This research and design project will improve how the rocket design team will decide and manufacture nozzles going forward. The impact of this improvement allows the rocket design team to take steps toward being self-sustaining by manufacturing student designed parts as opposed to commercially bought parts. This will not only be successful in increasing student impact on future designs, but also provides a technical challenge for the authors and will present as an impressive feat …

Fault-Tolerant Trajectory Tracking Of Unmanned Aerial Vehicles Using Immunity-Based Model Reference Adaptive Control, Brenton K. Wilburn

Graduate Theses, Dissertations, and Problem Reports (ETD)

This dissertation presents the design, development, and simulation testing of an adaptive trajectory tracking algorithm capable of compensating for various aircraft subsystem failures and upset conditions. A comprehensive adaptive control framework, here within referred to as the immune model reference adaptive control (IMRAC) algorithm, is developed by synergistically merging core concepts from the biologically- inspired artificial immune system (AIS) paradigm with more traditional optimal and adaptive control techniques. In particular, a model reference adaptive control (MRAC) algorithm is enhanced with the detection and learning capabilities of a novel, artificial neural network augmented AIS scheme. With the given modifications, the MRAC …

Vibration-Based Health Monitoring Of Multiple-Stage Gear Train And Differential Planetary Transmission Involving Teeth Damage And Backlash Nonlinearity, Andrew Patrick Sommer

Master's Theses

The objective of this thesis is to develop vibration-based fault detection strategies for on-line condition monitoring of gear transmission systems. The study divides the thesis into three sections. First of all, the local stresses created by a root fatigue crack on a pinion spur gear are analyzed using a quasi-static finite element model and non-linear contact mechanics simulation. Backlash between gear teeth which is essential to provide better lubrication on tooth surfaces and to eliminate interference is included as a defect and a necessary part of transmission design. The second section is dedicated to fixed axis power trains. Torsional vibration …