Propulsion and Power Commons^™

Magnesium-Enhanced Methane: A Novel Metalized Fuel For Mars Return Missions And Next-Generation Propulsion Systems, Kinga Wysocka

Discovery Day - Daytona Beach

This research investigates magnesium-enhanced methane as a novel metalized fuel concept for high-performance, in-situ resource utilization (ISRU)-compatible rocket propulsion. While methane is a leading candidate for Mars missions due to its producibility via the Sabatier process, its combustion performance is limited by the high activation energy of the initial C–H bond (~4 eV). To address this limitation, density functional theory (DFT) calculations were performed to analyze methane and hydrogen interactions with a Mg(0001) surface. A converged slab model (3×3×4 and 3×3×5) was validated with energy differences below 1 meV per atom for k-point sampling and ~13.99 meV per atom for …

Design And Development Of A Resonance Ignition System Using Gaseous Propellants, Benjamin J. Hoefer

Master's Theses

This work presents the development and experimental evaluation of a resonance igniter (RI) operating with premixed gaseous propellants. Resonance ignition is a non-electrical ignition concept in which an underexpanded jet impinges on a closed-end Hartmann–Sprenger tube (HST), generating cyclic compression and expansion waves that rapidly heat gas near the tube endwall. A modular experimental system was designed and built to investigate resonance ignition using methane–air and methane–oxygen mixtures. The system includes a supplemental configuration that may probe for mixture conditions favorable to ignition, informing RI testing. Pressure and temperature measurements were used to characterize pressure control, mixture pressure ratio (MPR), …

Conceptual Exploration Of Film Cooling Techniques In Hydrogen Gas Turbines, Wen Wu

Student Research Symposium (SRS)

Film cooling is a key heat transfer technique that protects gas turbine blades from extreme temperatures, allowing higher turbine inlet temperatures and greater thermal efficiency. It works by ejecting a thin layer of cooler air from the compressor through small holes onto the hot surface, creating a protective film layer that lowers surface temperature and reduces thermal stress on blades. This process is vital in power generation and propulsion systems that operate near material limits. With growing emphasis on sustainability, film cooling has gained new importance in hydrogen-fueled gas turbines. Hydrogen combustion creates water vaper and low-density exhaust gases, which …

Computational Study Of Rotating Detonation Combustors, Aditya Balasubramaniam

Mechanical and Aerospace Engineering Theses

Rotating detonation combustors (RDCs) are pressure-gain combustion devices that sustain one or more continuously rotating detonation waves, offering potential thermodynamic and performance advantages over conventional deflagration-based systems. Their behavior depends strongly on combustor geometry and operating conditions. Understanding these effects is therefore essential for the design and optimization of practical RDCs. Accordingly, this thesis numerically investigates annular RDCs with two primary objectives: (1) to evaluate the effects of propellant mass flux and (2) to assess the influence of annular width on detonation-wave dynamics and combustor performance.

A finite-volume framework is used to solve the compressible reactive Euler equations with hydrogen–air …

Investigation On Selective Catalytic Reduction For Retrofit Of Commercial Aviation Aircraft Engines, Connor M. Wall

Graduate Studies Theses and Dissertations 2026

As the aviation industry continues to grow, the ever-increase of emissions from the sector becomes a growing concern. While the International Civil Aviation Organization (ICAO) set a goal of net-zero carbon emissions by 2050, there are other emissions like contrails and NOx that must still be addressed. Selective Catalytic Reduction (SCR) has been used in the transportation and power generation industry for over two decades and has been an effective solution for NOx reduction. Even with the success SCR has had in other industries, its capabilities in the aviation industry have been trivially investigated. Aircraft engines pose an unique challenge …

Numerical Modelling And Co-Optimization Of Gasoline Fuels For Gasoline Compression Ignition Using Multi Component Approach, Ashwin Karthik Purushothaman

Dissertations, Master's Theses and Master's Reports

Future mobility is expected to rely on a broad spectrum of powertrain technologies, including battery electric vehicles (BEVs), hybrid electric vehicles (HEVs), fuel cell electric vehicles (FCEVs) and traditional internal combustion engine (ICE) vehicles. Despite the shift toward electrification, internal combustion engines are projected to remain a key component of future powertrains, either as the primary power source or as range extenders to generate electricity in hybrid systems. As such, significant research efforts continue to focus on enhancing the efficiency and reducing the emissions of ICEs to meet increasingly stringent regulatory and environmental targets. Gasoline compression ignition (GCI) has been …

Hybrid Rans-Les Analysis Of Turbulent Flame Under Near Blow-Off Condition In A Multi-Stage Swirl Combustor, Brandon O'Brien

College of Graduate Studies: Theses & Dissertations

Advances in computational resources are making computational fluid dynamics (CFD) increasingly accessible for a variety of engineering applications. However, certain complex problems, such as simulating detailed flame kinetics, remain computationally prohibitive for many users. Developing cost-effective methods to simulate these challenges would greatly benefit applications involving flame dynamics, such as turbine engines or industrial burners. This study investigates the effect of main stage swirler intensity on near lean blow-off characteristics in a multi-staged swirl combustor using Ansys Fluent. The hybrid RANS-LES turbulence model, Stress Blended Eddy Simulation (SBES) coupled with Flamelet Generated Manifold (FGM) combustion model was selected to model …

The Impact Of Film Cooling On The Heat Release Within A Rotating Detonation Combustor, Shreyas Ramanagar Sridhara, Antonio Andreini, Marc D. Polanka, Myles D. Bohon

Faculty Publications

Rotating detonation combustors establish a detonation wave that continuously circulates inside a small annulus. The presence of the detonation wave and the downstream oblique shock within the small annulus coupled with high mass flow induces a high heat load to the combustor wall. Preliminary analysis shows that for higher thermal power, internal air cooling alone is not sufficient to remove the heat out of the walls to maintain them below the maximum temperature of the metal. A possible solution is to use film cooling to reduce the heat flux to the combustor walls. One issue, though, is that the introduction …

Benchmarking Of A Sco2 Heat Exchanger Flow Loop, David Velasco

Doctoral Dissertations and Master's Theses

Heat transfer of supercritical carbon dioxide (sCO2) was studied experimentally by commissioning a sCO2 flow loop featuring a horizontal tube-in-tube counterflow heat exchanger with a circular cross section. The main objective was to establish experimental heat transfer research capabilities for sCO2 at Embry-Riddle Aeronautical University’s (ERAU) Thermal Science Lab. sCO2 experiences a drastic change in thermophysical properties near its critical point that results in unique heat transfer characteristics. The high pressures at which sCO2 exists make the large gradients in thermophysical and transport properties difficult to study, experimentally and numerically. However, understanding the heat transfer characteristics and thermophysical behavior of …

Design Of An Experimental Solid Rocket Motor, Johnathan Bettes, Andrew Fuller

Williams Honors College, Honors Research Projects

This project utilizes mechanical and chemical principles to characterize propellant grains and to manufacture a custom nozzle to create experimental Solid Rocket Motors (SRMs) with a propellant called Angry Listerine. For the propellant grains, one major non-chemical factor that determines its thrust performance is the grain geometry, or the core of the grains for which hot gases flow through the propellant and out of the nozzle to further react with exposed chemical surfaces. The two kinds of grain geometries analyzed and tested in this report are called MoonBurner, an offset circular core, and Finocyl, a gear-shaped core. The nozzle for …

Investigations Of Performance And Emissions Of A Fischer-Tropsch Gtl Sustainable Aerospace Fuel With Lubricity Improver In A Compression Ignition Engine With Butanol Port Fuel Injection, James B. Willis

College of Graduate Studies: Theses & Dissertations

As there is increasing concern over emissions of traditional fossil fuels, as well as the future of continued reliance on this dwindling resource, it is becoming increasingly evident that alternative fuels are a necessity. This research investigates the use of a Fischer-Tropsch fuel from natural gas feedstocks, S8, in an internal combustion research engine with a common rail fuel injection system. This synthetic kerosene fuel has a high DCN of 62, indicating high affinity to autoignition compared to conventional pump diesel (ULSD) at 48 DCN. However, due to the process by which it is produced, this fuel lacks the necessary …

Investigations Of A Surrogate Fuel Based On Fischer-Tropsch Gtl And Ctl In Cvcc, Idi And Di Compression Ignition Engines, Amanda C. Weaver

College of Graduate Studies: Theses & Dissertations

With the increase in availability, feedstocks, and properties of alternative fuels, compatibility issues emerge between current engine platforms often requiring a limit on the blend percentage of alternative fuel in conventional fuel or alteration to the engine platform. Two key metrics were identified, autoignition quality and lubrication characteristics, as vital for the proper function of a compression ignition engine, and if the blend of alternative fuels matches these two criteria for the diesel standard, then the resulting blend percentage can be considered as a viable alternative for complete replacement of conventional petroleum ULSD. Autoignition quality was matched using blends S-8, …

Improving The Delivered Specific Impulse Of Composite Rocket Propellant Through Alteration Of Chemical Composition: Methodology And Parameters For Characterization Of Propellant And Validation Of Simulation Software Common To The Amateur Rocketry Community, Isaac O'Brien, Austin Ryan

Williams Honors College, Honors Research Projects

In this study, two solid composite rocket propellants were designed utilizing ProPEP, a rocket propellant formulation software common in the amateur and hobby rocketry communities. The two propellants were designed to optimize specific impulse relative to a literature propellant designed by 1020 Research Labs. The literature propellant was also tested in order to validate the design of experiment as well as the mixing and testing procedures. All three propellants, which includes the literature propellant RCS-P, and the two novel propellants AKR-P1 and AKR-P2 were characterized with static tests. The results of the static tests provide data on propellant performance and …

In-House Fabrication Of Temperature Sensitive Paint For Turbine Cooling Research, Mayur D. Patel, Mark A. Ricklick

Beyond: Undergraduate Research Journal

The Temperature Sensitive Paint (TSP) is a widely used method in measuring and visualizing flow separation and heat transfer. Compared to the cost and time consumption needed for methods such as pitot tubes, temperature sensitive paint is a cheaper alternative. Due to high usage in College of Engineering research projects, it was determined that in house fabrication of temperature sensitive paint would reduce time and cost limitations. For initial stages, literature research was performed to determine the recipe of intensity based TSP with luminophore and polymer binder that operated optimum at temperatures from 0-100°C. Europium III thenoyltrifluoroacetonate was determined to …

Advanced Visualization Techniques Of Hot-Jet Combustion Of Lean And Ultra-Lean Substances, Timothy I. Machin, Li Qiao

The Summer Undergraduate Research Fellowship (SURF) Symposium

Research has been conducted on ignition of natural gas as a potential replacement for fossil fuels. A reason natural gas is not widely used and adapted is because of the harmful emissions created when combusted in rich mixtures, but if the gas can be burned at a lean or ultra-lean equivalence ratio, these emissions can be reduced or even eliminated. One method of burning lean and ultra-lean substances is by use of hot-jet ignition. This method ignites the substance near its combustion temperature, reducing the harmful emissions. This method is not yet fully understood, and so research must be done …

Ramjet Combustion Chamber, Paul Cameron Stone

Aerospace Engineering

A ramjet combustion chamber is designed and some initial assembly fabrication and test completed as a component of a ramjet graduate project for California Polytechnic State University, San Luis Obispo Supersonic Wind Tunnel. The combustor design is driven by a theoretical model created by a Cal Poly graduate student, Harrison Sykes. Temperature, pressure, and fuel flow will be measured.

Cycle Performance Of A Pulse Detonation Engine With Supercritical Fuel Injection, Timothy M. Helfrich

Theses and Dissertations

Pulse detonation engines (PDE) rely on rapid ignition and formation of detonation waves. Because hydrocarbon fuels are composed typically of long carbon chains that must be reduced in the combustion process, it would be beneficial to create such reduction prior to injection of fuel into the engine. This study focused on PDE operation enhancements using dual detonation tube, concentric-counter-flow heat exchangers to elevate the fuel temperature up to supercritical temperatures. Variation of several operating parameters included fuel type (JP-8, JP-7, JP-10, RP-1, JP-900, and S-8), ignition delay, frequency, internal spiral length, and purge fraction. To quantify the performance, four key …