Propulsion and Power Commons^™

Aerodynamic Design And Structural Evaluation Of A Global Minimum Torque Inspired Multirotor Propeller, Zeke Bukovansky

Master's Theses

This thesis develops a repeatable design, CAD, aerodynamic postprocessing, structural screening, and manufacturing feasibility workflow for a 22-inch global minimum torque inspired multirotor propeller. Matched MIL and GMT geometries were compared at a 35 N, 4000 rpm static-hover operating condition using BEMT/XFOIL aerodynamic postprocessing, with diameter, blade count, chord distribution, airfoil schedule, and target thrust held constant. The final modeled comparison predicted a modest 1.5% reduction in torque and shaft power for the GMT case while maintaining the same thrust target. CAD construction, MATLAB reduced-order beam model, Abaqus screening, and manufacturing planning were used to identify geometry level structural and …

A Test Rig For An Aircraft Propeller Powered By Battery Motor, C. M. Vigneswaran, J. Induja, K. S. Bharath, M. J. Spoorthi, R. Chethana

Journal of Aviation Technology and Engineering

The propeller test rig is a crucial component in aeronautical engineering that plays a vital role in the development, testing, and optimization of propeller systems for aircraft. This research outlines the design, development, and performance evaluation of a state-of- the- art propeller test rig developed for research and testing purposes. The primary objective of this project is to enhance the understanding of propeller dynamics and efficiency, leading to the improvement of aircraft propulsion systems. The test rig provides a controlled environment to evaluate and compare multiple propeller designs, aiding engineers in making informed decisions during the design process. An advanced …

Prediction Of Noise Associated With An Isolated Uav Propeller, Samuel O. Afari

Doctoral Dissertations and Master's Theses

The emergent field of interest in the Urban Air Mobility community is geared towards a world where aerial vehicles are commonplace. This poses the problem of the effects of the radiated noise. The present research presents an in-depth analysis of the noise generation mechanism of a propeller as a mode of propulsion of the said aerial vehicles. Numerical simulation utilizing a Hybrid Large-Eddy Simulation (LES) coupled with Unsteady Reynolds-Averaged Navier-Stokes (RANS) solver, is adopted on an isolated propeller modeled from the commercial DJI Phantom II 9450 propeller. The Spalart-Allmaras one equation turbulence model with rotation/curvature correction is used. The Farassat’s …

A Thrust Equation Treats Propellers And Rotors As Aerodynamic Cycles And Calculates Their Thrust Without Resorting To The Blade Element Method, Phillip -. Burgers

International Journal of Aviation, Aeronautics, and Aerospace

The lift generated by a translating wing of known translational speed, lift coefficient and area is calculated by a simple equation. A propeller or rotor generating thrust share the same aerodynamic principles but their different kinematics cause the calculation of their thrust to be laborious. This paper derives a thrust equation from an algebraic expansion of the Prandtl’s dynamic pressure term q_∞by adding the rotational kinetic energy of a propeller or rotor to the existing translational kinetic energy term. This thrust equation can be applied directly to propellers and rotors and assumes these to operate as cycles with …

Proof Of Concept For Propeller Performance Testing In The Cal Poly Wind Tunnel, Alex N. May, Clayton R. Green, Clinton J. Kirsop, Jason A. Schupp

Aerospace Engineering

The goal of this experiment was to execute a proof of concept for a potential propulsion systems laboratory. During the course of this experiment, a data acquisition system was designed, built, and tested in order to collect data from the Cal Poly 3x4 ft draw-down wind tunnel. By operating a brushless outrunner motor and propeller on the sting mount, data was collected for thrust, torque, RPM, current, voltage, and tunnel velocity. By obtaining data for each of these performance metrics, trends were analyzed to confirm the concept and apparatus was functional. The results of the experiment revealed that the concept …

Electric Aircraft Propulsion System, Austin J. Doupe

Aerospace Engineering

This report specifies the purpose, assembly, operation, and data collection of a testing apparatus to characterize small electric aircraft propulsion systems designed for commercial use. This apparatus was constructed with the goal of determining overall system characteristics and efficiencies. The apparatus was pushed to a safety limit as deemed by advisor John Dunning and the results of the experiment were an output power of 3.2kW (25% of max rated power) and a system efficiency of 58.6%, both of which occurred at 2200 RPM. Currently the apparatus needs improvement. It should have an upgraded structure to mount to (instead of the …

A Three Dimensional Vortex Particle-Panel Code For Modeling Propeller-Airframe Interaction, Jacob S. Calabretta

Master's Theses

Analysis of the aerodynamic effects of a propeller flowfield on bodies downstream of the propeller is a complex task. These interaction effects can have serious repercussions for many aspects of the vehicle, including drag changes resulting in larger power requirements, stability changes resulting in adjustments to stabilizer sizing, and lift changes requiring wing planform adjustments.

Historically it has been difficult to accurately account for these effects at any stage during the design process. More recently methods using Euler solvers have been developed that capture interference effects well, although they don't provide an ideal tool for early stages of aircraft design, …