Open Access. Powered by Scholars. Published by Universities.®
Articles 1 - 5 of 5
Full-Text Articles in Propulsion and Power
Critical Design Parameters For Pylon-Aided Gaseous Fuel Injection Upstream Of A Flameholding Cavity, Mitchell R. Pohlman
Critical Design Parameters For Pylon-Aided Gaseous Fuel Injection Upstream Of A Flameholding Cavity, Mitchell R. Pohlman
Theses and Dissertations
The Air Force Institute of Technology and the AFRL are investigating means to increase the efficiency of fuel-air mixing into supersonic flow. Previous work has shown much promise in increasing the penetration and mixing of a fuel-air mixture into the freestream by injecting fuel behind small triangular pylons. Pylon-aided fuel injection has also shown to lift the fuel plume off the combustor floor; this floor-gap prevents the ignition of fuel seeded in the boundary layer. In this paper twenty-one pylons of varying widths, heights, and lengths were examined in four specific test matrices within a CFD environment. Pylons in test …
Pylon Effects On A Scramjet Cavity Flameholder Flowfield, Andrew B. Freeborn
Pylon Effects On A Scramjet Cavity Flameholder Flowfield, Andrew B. Freeborn
Theses and Dissertations
Cavity flameholders in supersonic combustion ramjet (scramjet) combustors, while effective, fail to take advantage of the full combustor volume. Adding a pylon to the leading edge of a cavity flameholder generates a flowfield increasing mass exchange between the cavity and main combustor flow, increasing the mixing interface between flameholder products and main combustor flow, and exhibiting minimal Reynolds number effects. To demonstrate this modified flowfield driven by supersonic expansion behind the pylon, pylon-cavity flameholder flowfield data were obtained through a combination of wind tunnel experimentation and steady-state computational fluid dynamics (CFD). Flowfield effects of the pylon-cavity were examined at a …
Hypermixer Pylon Fuel Injection For Scramjet Combustors, Jason C. Doster
Hypermixer Pylon Fuel Injection For Scramjet Combustors, Jason C. Doster
Theses and Dissertations
Fueling the core airflow of a circular or elliptical scramjet combustor cross-section often requires intrusive geometries. Intrusive geometries can distribute the fuel evenly across the combustor cross-section and act as a flameholder for the fuel/air mixture. Compared to conventional transverse or angled wall injection, intrusive geometries allow easier penetration into the core combustor airflow and reduced fuel injection pressures. The design and testing of an intrusive pylon geometry for scramjet combustor fueling is the subject of this research. Three pylon configurations are compared: a basic pylon, a ramp pylon, and an alternating wedge pylon. All three pylon configurations exhibit the …
Performance Measurements Of Direct Air Injection In A Cavity-Based Flameholder For A Supersonic Combustor, Scott G. Edens
Performance Measurements Of Direct Air Injection In A Cavity-Based Flameholder For A Supersonic Combustor, Scott G. Edens
Theses and Dissertations
For several years the Air Force Research Lab Propulsion Directorate has been studying the difficulties in fueling supersonic combustion ramjet engines with hydrocarbon based fuels. Recent investigations have focused on the use of direct air injection into a directly-fueled cavity-based flameholder. Direct air injection has been shown qualitatively to be a valuable tool for improving cavity combustion. Little quantitative data is available that characterizes the performance of cavity-based flameholders. The objective of this research was to quantitatively determine the specific advantages and disadvantages of the direct air injection scheme. This was accomplished via intrusive probing into a supersonic free stream …
Study Of Magnetogasdynamic Flow Acceleration In A Scramjet Nozzle, Erik K. Ross
Study Of Magnetogasdynamic Flow Acceleration In A Scramjet Nozzle, Erik K. Ross
Theses and Dissertations
The research project studied the benefits of Magnetogasdynamic (MGD) acceleration on a scramjet nozzle. MGD is a technology that relies on electromagnetic fields to extract and/or add energy to flow fields. The scramjet engine in the "AJAX" concept proposed by D.I. Brichkii et al. (2001) of St. Petersburg, Russia would utilize an MGD power generator in the diffuser user which could potentially provide electrical power for the aircraft support systems and an MGD accelerator in the nozzle of the engine. Using an AFRL/VAAC CFD code that was modified for MGD computations, this project investigated the effect conductivity and load factor …