Aeronautical Vehicles Commons^™

W&B Problems For Far/Cs 25 Airplanes Tutorial, Nihad E. Daidzic

Aviation Department Publications

Weight and Balance (W&B) computations are essential step in ensuring that the aircraft (in this case FAR/CS 25 Transport-category airplanes) is properly loaded with its Center of Mass (CM) of Center of Weight/Gravity (CG) in the proper range.

Fe Modeling Methodology For Load Analysis And Preliminary Sizing Of Aircraft Wing Structure, Jun Hwan Jang, Sang Ho Ahn

International Journal of Aviation, Aeronautics, and Aerospace

It is a critical part at the basic design phase of aircraft structural design to build a finite element model and it will have a direct impact on time and cost for airframe structure development. In addition, the objective of finite element model will be varied depending on each design review phase and the modelling methodology varied accordingly. In order to build an effective and economic finite element model, it is required to develop adequate level of modelling methodology based on each design phase and its objectives. Therefore, in this paper, the finite element modeling methodology was presented for internal …

Comparison Of Fixed-Wing Unmanned Aircraft Systems (Uas) For Agriculture Monitoring, Joseph Cerreta, Kristine M. Kiernan

International Journal of Aviation, Aeronautics, and Aerospace

Florida citrus growers need inexpensive methods to observe citrus plants to detect disease and stress consistently. Health vegetation indices, such as the Normalized Difference Vegetation Index (NDVI) collected from Unmanned Aircraft Systems (UAS), can be used to identify variation in plant health. Simple-to-operate UAS may enable growers to determine within-field variation more frequently than with inspections from scouts, providing more frequent knowledge about the crop condition. This research compared two low-cost fixed-wing UAS, a $5,000 Parrot Disco Pro Ag and a $16,690 senseFly eBee, each equipped with a Parrot Sequoia multispectral camera, to determine if there were differences in the …

In-Flight Wingtip Folding: Inspiration From The Xb-70 Valkyrie, Gaétan X. Dussart, Mudassir Lone, Ciaran O'Rourke, Thomas Wilson

International Journal of Aviation, Aeronautics, and Aerospace

Wingip folding can be used to extend aircraft wingspan, allowing designers to take advantage of reduced induced drag whilst respecting ground operational limitations. Such devices can also be used in-flight for a variety of other benefits including load alleviation and flight control. The majority of in-flight folding research takes inspiration in past developments made on the XB-70 Valkyrie, which used the folding devices for stability and lift performance benefits. In this paper, the authors investigate the capabilities of the folding wingtip system and potential scaling to large civil aircraft. Manufacturing details are used to size the actuators whilst the aerodynamic …

A Thrust Equation Treats Propellers And Rotors As Aerodynamic Cycles And Calculates Their Thrust Without Resorting To The Blade Element Method, Phillip -. Burgers

International Journal of Aviation, Aeronautics, and Aerospace

The lift generated by a translating wing of known translational speed, lift coefficient and area is calculated by a simple equation. A propeller or rotor generating thrust share the same aerodynamic principles but their different kinematics cause the calculation of their thrust to be laborious. This paper derives a thrust equation from an algebraic expansion of the Prandtl’s dynamic pressure term q_∞by adding the rotational kinetic energy of a propeller or rotor to the existing translational kinetic energy term. This thrust equation can be applied directly to propellers and rotors and assumes these to operate as cycles with …

Optimization And Analysis Of An Elite Electric Propulsion System, Mehakveer Singh, Kapil Yadav, Satnam Singh, Vikas Chumber, Harikrishna Chavhan

International Journal of Aviation, Aeronautics, and Aerospace

Abstract- Electric propulsion has a promising system to create new possibilities in this technological era as well as control the harmful gaseous emission. This paper put a vision on several parameters of electric propulsion. The engine’s performance is comparable to the current propulsion devices and provides a lightweight solution to the robust technologies’ dependent on chemical energy sources. There are a plethora of factors which is enhanced by electric propulsion such as, overall efficiency, capabilities, and robustness of future air vehicles as well as mainly overcome from exhaust hazards. Electric propulsion systems have the potential of utilizing the electrically-driven propulsion …

Effect Of Chemical Reactions On The Fluidic Thrust Vectoring Of An Axisymmetric Nozzle, Rachid Chouicha, Mohamed Sellam, Said Bergheul

International Journal of Aviation, Aeronautics, and Aerospace

Abstract:

During the last years, several thrust control systems of aerospace rocket engines have been developed. The fluidic thrust vectoring is one of them; it is simple in design and offers a substantial gain in weight and in performance. Most of studies related to this device were carried out with cold gas. It’s quite legitimate to expect that the thermophysical properties of the gases may affect considerably the flow behavior. Besides, the effects of reacting gases at high temperatures, under their effects all flow parameters like to vary.

This study aims to develop a new methodology that allows studying and …

Design And Realization Of An Unmanned Aerial Rotorcraft Vehicle Using Pressurized Inflatable Structure, Nirmal Sadasivan

International Journal of Aviation, Aeronautics, and Aerospace

Unmanned aerial rotorcraft vehicles have many military, commercial and civil applications. There is a necessity to advance the performance on several ranges of rotorcraft for using these vehicles successfully in the expanded future roles. A lower flight time, noise disturbance and safety issues remain the key obstacles in increasing the efficiency of the rotorcraft for various applications. This work presents the design and realization of a rotorcraft using pressurized inflatable structure filled with lighter than air gas such as helium or hydrogen to provide lift assistance for the vehicle. Two iterative design procedures were developed for designing the vehicle. One …

Design Guidelines For Supersonic Aircrafts In Civil Aviation, Tridib Banerjee Mr.

International Journal of Aviation, Aeronautics, and Aerospace

There exists no publication currently available to the scholars that address in detail, every aspect of designing a modern supersonic aircraft for civil aviation. This paper aims to resolve that issue. It reviews all the existing work that has been done on the topic so far and builds upon that. It incorporates multiple disciplines and takes into account the closely inter-coupled effects of each component on one-another. It also analyses in detail the various environmental and modern regulatory challenges like sonic boom and means to overcome them. It further addresses the challenges like logistics, cabin crew radiation exposure, and cost …

Improving The Delivered Specific Impulse Of Composite Rocket Propellant Through Alteration Of Chemical Composition: Methodology And Parameters For Characterization Of Propellant And Validation Of Simulation Software Common To The Amateur Rocketry Community, Isaac O'Brien, Austin Ryan

Williams Honors College, Honors Research Projects

In this study, two solid composite rocket propellants were designed utilizing ProPEP, a rocket propellant formulation software common in the amateur and hobby rocketry communities. The two propellants were designed to optimize specific impulse relative to a literature propellant designed by 1020 Research Labs. The literature propellant was also tested in order to validate the design of experiment as well as the mixing and testing procedures. All three propellants, which includes the literature propellant RCS-P, and the two novel propellants AKR-P1 and AKR-P2 were characterized with static tests. The results of the static tests provide data on propellant performance and …

Immunity-Based Framework For Autonomous Flight In Gps-Challenged Environment, Mohanad Al Nuaimi

Graduate Theses, Dissertations, and Problem Reports (ETD)

In this research, the artificial immune system (AIS) paradigm is used for the development of a conceptual framework for autonomous flight when vehicle position and velocity are not available from direct sources such as the global navigation satellite systems or external landmarks and systems. The AIS is expected to provide corrections of velocity and position estimations that are only based on the outputs of onboard inertial measurement units (IMU). The AIS comprises sets of artificial memory cells that simulate the function of memory T- and B-cells in the biological immune system of vertebrates. The innate immune system uses information about …

Aerodynamic Design And Exploration Of A Blended Wing Body Aircraft At Subsonic Speed, Sam Dakka Dr, Oliver Johnson

International Journal of Aviation, Aeronautics, and Aerospace

Blended Wing Body (BWB) is a novel aircraft concept which provides many different aerodynamic benefits over conventional aircrafts design. This research investigated the BWB design, L/D characteristics, surface pressure distribution and span-wise lift distribution of a BWB aircraft at low to medium subsonic speeds. A BWB model was designed, manufactured and tested in a subsonic wind tunnel to validate the CFD simulation. The results gained from the investigation proved that BWB has a L/D improvement of 9.4% than conventional aircrafts and 21% increase at medium subsonic speeds (Mach 0.6) compared to lower subsonic speeds of 25 m/sec. It was found …

Uas Flight Operations In Complex Terrain: Assessing The Agricultural Impact From Hurricane Maria In The Central Mountainous Region Of Puerto Rico, Kevin Adkins

Publications

Hurricane Maria struck Puerto Rico in September 2017 as a Category 4 storm causing major damage to infrastructure, agriculture and natural ecosystems, as well as the loss of many lives. Among the crops hardest hit was coffee, one of the most important crops in Puerto Rico. As a perennial system, coffee takes various production forms along a gradient from high shade/biodiversity coffee farms to low shade coffee monocultures and therefore offers an ideal means for the study of resistance and resilience of an agroecosystem to weather and climate disturbance. During the summer of 2018, 14 impacted farms across the production …

Design And Implementation Of Intelligent Guidance Algorithms For Uav Mission Protection, Karina Rivera

Doctoral Dissertations and Master's Theses

In recent years, the interest of investigating intelligent systems for Unmanned Aerial Vehicles (UAVs) have increased in popularity due to their large range of capabilities such as on-line obstacle avoidance, autonomy, search and rescue, fast prototyping and integration in the National Air Space (NAS). Many research efforts currently focus on system robustness against uncertainties but do not consider the probability of readjusting tasks based on the remaining resources to successfully complete the mission. In this thesis, an intelligent algorithm approach is proposed along with decision-making capabilities to enhance UAVs post-failure performance. This intelligent algorithm integrates a set of path planning …

Anticoincidence Detector Performance Analysis, Christopher Helmerich, Erik Korzon

Von Braun Symposium Student Posters

No abstract provided.

Rainbow Horizons: High Altitude Visible Spectrum Analysis, F Gonzalez, N Schragal, E Leiser, A Raney, J Seese

Von Braun Symposium Student Posters

No abstract provided.

Radiation Detection At Ultra-High Altitudes, Samantha Johnson, Christopher Helmerich

Von Braun Symposium Student Posters

No abstract provided.

Design Of A Heavy Lift Rc Aircraft - Society Of Automotive Engineers (Sae) Aero Design® West Competition Team, Jiyoung Hwang, Phillip Nielsen

Undergraduate Research Symposium - Prescott

The SAE Aero West design competition challenges undergraduate students to design and build an RC aircraft that will fly with the maximum number of passengers and luggage possible. The ERAU SAE team focuses on simulation-based research and project methods such as Computational Fluid Dynamics (CFD), aircraft optimization, and Finite Element Analysis (FEA). Designing and manufacturing a well-designed heavy lift aircraft and competing with other groups will give experience in solving engineering problems. The Aerodynamics team is currently focusing on score optimization, aircraft performance and configuration. The propulsion team is constructing a test rig to test various propellers and motors to …

Eagle Aero Sport: Student-Built Aircraft, Rachael Bradshaw, Nick Bartholet

Undergraduate Research Symposium - Prescott

Eagle Aero Sport (EAS) is the first student operated aircraft build team at Embry-Riddle Aeronautical University. Our team allows students to gain hands-on experience in all aspects of aircraft production including: aircraft assembly, design engineering, management of production operations, finance, marketing, and team building skills. Through research, and consulting with the Experimental Aircraft Association, our airplane of choice is the Van’s RV-12. EAS is modifying the airplane to add real time flight test instrumentation for research. These instruments will gather data for aerodynamic, structural, as well as aircraft performance experiments. Presently, EAS is progressing with Build Team 60% complete and …

Telemetry Subsystem With Higher Access Duration For Leo Satellites, Jose L. Garcia

Morehead State Theses and Dissertations

A thesis presented to the faculty of the College of Science at Morehead State University in partial fulfillment of the requirements for the Degree of Master of Science by Jose L. Garcia on September 10, 2018.

Clean-Fuel E-Vtol Air Mobility Vehicles For Unmanned And Manned Operations, Larry D. Mccarroll, Brian Morrison, Bruce J. Holmes D.E., Faiaa, Fraes, Henry Vu

National Training Aircraft Symposium (NTAS)

Imagine for a moment, having your very own safe, affordable, clean-fuel, point-to-any point vehicle for travel in the 21st-century 3-dimensional airspace system. Your ultra-reliable e-VTOL allows commuters to leave behind the constraints of hub-and-spoke airports, and the congestion of interstates, turnpikes and freeways. Facilitating Inter- and Intra-urban travel, such as downtown-to-airport, or metropolis-to-metropolis, or home-to-work. Perfect for dense urban environments worldwide. And all while offering the clean power of hydrogen for zero-emission travel.

This vision for efficient, clean, delay-free mobility has been talked about for decades, but always waived aside as some kind of futurist vision. This future requires tackling …

Experiments Of Propeller-Induced Flow Effects On A Low-Reynolds-Number Wing, Gavin K. Ananda, Robert Deters, Michael S. Selig

Publications

Novel findings are discussed in this paper that will be especially beneficial to designers and modelers of small-scale unmanned air vehicles and high-altitude long-endurance vehicles that both operate at low Reynolds numbers (Re = 50,000-300,000). Propeller-induced Oow effects in both tractor and pusher configurations on a recta ngular wing using the Wortmann FX 63-137 airfoil (a common low-Reynolds-number high-lift airfoil) are presented in this paper . Significant performance benefits can be found for a wing in the tractor configuration. Experiments, including trip tests and upper-surface oil Dow visualization, show and verify that the propeller slipstream induces early transition to turbulent …

A Comparison Of The Strengths And Weaknesses Of Small-Format Aerial Photography Platforms, Jeremy W. Aber, Tyler A. Babb, Douglas E. Campbell, Kevin M. Corns

International Journal of Aviation, Aeronautics, and Aerospace

The demand for small-format aerial photography continues to grow in large part due to the rapid adoption of unmanned aerial vehicles (UAVs). Prior to the explosion of UAV use, this kind of photography was collected using older technologies such as tethered kites and blimps. Due to the increased demand for aerial imagery, this article looks at four platforms commonly used to collect small-format aerial imagery: multi-rotor UAVs, fixed-wing UAVs, kites, and blimps. Practical use considerations are explored, including characteristics of flight and operation, atmospheric and site factors, imaging sensors and costs, and regulatory limitations.

Each of the four categories of …

Surgical And Medical Applications Of Drones: A Comprehensive Review, James C. Rosser, Vudatha Vignesh, Brent A. Terwilliger, Brett C. Parker

Publications

Background: Drones have the ability to gather real time data cost effectively, to deliver payloads and have initiated the rapid evolution of many industrial, commercial, and recreational applications. Unfortunately, there has been a slower expansion in the field of medicine. This article provides a comprehensive review of current and future drone applications in medicine, in hopes of empowering and inspiring more aggressive investigation. Database: A literature search was performed by EBSCO (Elton B. Stephens Company) Discovery Service, searching the phrases "drones," "UAV," "unmanned aerial vehicles," "UAS," and "unmanned aerial systems." A second search was used to identify sources that contained …

Surgical And Medical Applications Of Drones: A Comprehensive Review, Brent Terwilliger, James C. Rosser Jr., Vudatha Vignesh, Brett C. Parker

Publications

Drones have the ability to gather real time data cost effectively, to deliver payloads and have initiated the rapid evolution of many industrial, commercial, and recreational applications. Unfortunately, there has been a slower expansion in the field of medicine. This article provides a comprehensive review of current and future drone applications in medicine, in hopes of empowering and inspiring more aggressive investigation.

Book Review: Fundamentals Of International Aviation, Alan Bender

International Journal of Aviation, Aeronautics, and Aerospace

Not applicable.

The Pocketqube Standard: Issue 1, Robert J. Twiggs

Robert "Bob" Twiggs STEM Education Collection

A report titled "The PocketQube Standard Issue 1" published on June 7, 2018.

Investigating Forward Flight Multirotor Wind Tunnel Testing In A 3-By 4-Foot Wind Tunnel, Reed Danis

Master's Theses

Investigation of complex multirotor aerodynamic phenomena via wind tunnel experimentation is becoming extremely important with the rapid progress in advanced distributed propulsion VTOL concepts. Much of this experimentation is being performed in large, highly advanced tunnels. However, the proliferation of this class of vehicles extends to small aircraft used by small businesses, universities, and hobbyists without ready access to this level of test facility. Therefore, there is a need to investigate whether multirotor vehicles can be adequately tested in smaller wind tunnel facilities. A test rig for a 2.82-pound quadcopter was developed to perform powered testing in the Cal Poly …

The Design And Implementation Of A Supersonic Indraft Tube Wind Tunnel For The Demonstration Of Supersonic Flows, Daniel Kenneth Johnson

Master's Theses

Historically, the endeavor of scale testing flight vehicles at supersonic Mach numbers, especially for long durations, has required the development of closed-loop wind tunnels, which are extremely expensive both to build and operate due to the high complexity and incredible power required to drive such a system. The intermittent blowdown wind tunnel, indraft tunnel, and shock tunnel have alleviated many of these cost requirements to some degree, whilst facilitating testing at very high Mach numbers and enthalpies; however, these systems require the handling of gases at pressures and temperatures that can be prohibitive for many university settings. The Ludwieg tube …

Development Of A Small Unmanned Aerial Vehicle Longitudinal Model For Future Flutter Testing, Said S. Hamada

Doctoral Dissertations and Master's Theses

This thesis presents the system identification of the longitudinal motion of a small unmanned aerial vehicle with flexible characteristics. The unmanned aerial vehicle of study is an off-the-shelf aircraft with limited knowledge about the dynamic model. The first task in obtaining a model for flutter testing is determining the rigid body model. Specifically, this thesis will focus in the development of the aircraft and obtaining the longitudinal rigid body model. This involves the assembly and configuration of the avionics and sensors, performing experiments to determine mass and inertia properties and using software tools for aerodynamic analysis to get preliminary values …