Aeronautical Vehicles Commons^™

Experimental Manufacturing Optimization Of 3d-Printed Ducted Fans, Stanlie Cerda-Cruz

Discovery Day - Daytona Beach

This study aims to assess the efficiency gains, feasibility, and practicality of 3D printing fan and ducts with pre and post processing techniques. With the rapid expansion of MAV use; labs, students, hobbyists, can benefit from manufacturing Electric Ducted Fans (EDFs), both fans and ducts, in-house rather than purchasing traditional propellers. There are several advantages of utilizing EDFs, as they can minimize wing tip vortices, reduce wake contraction, and induce a duct lip Coanda effect which all lead to an increased system efficiency. However, EDF implementation in MAV's remain largely unexplored due to the difficulty of development and the production …

Improving Fatigue Strength And Life Of Single Crystal Cmsx-4, Jochen Peter Fuhr, Lloyd Hackel, Nicolau I. Morar, Noah Holtham, Keivan Davami, Montu Sharma, Rajkumar Roy

15th International Conference on Shot Peening

The deep penetration of laser peening (LP) and retention of residual stress at high temperature by LP is significant in improving fatigue life and strength of superalloys exposed to high temperature and corrosion. Single crystal CMSX-4, was evaluated for stress relaxation and both fatigue life and fatigue strength of material that was LP-treated compared to non-LP and shot-peened (SP) specimens. LP was done with multiple layers using a 20 J/pulse laser where the laser high energy enabled using a 5 mm spot size on the metal surface. Stress measurements by the slitting technique showed the plastic penetration depth exceeded SP …

3d Printed Fixed Wing Aircraft Competition, Sidney E. Long, Mitchell Heise, Jack Bride, Daniel Salinas

Mechanical Engineering

Cal State LA and Arlington University, Texas are hosting the same 3D printed, fixed wing aircraft competition for 2025. Cal Poly requires a competitive plane that can adhere to each rule and be piloted remotely to achieve the longest time in the air. The plane must utilize solely 3D printing technology for the wings, body, and all other structures. The only off-the-shelf components can be the motor and electronics, as well as mechanical devices such as hinges.

40 - Design, Fabrication, And Installation Of Morphing Control Surfaces For Small-Scale Uas, Kyle Purser

Undergraduate Research Symposium

Morphing control surface technology, inspired by organic structures and compliant mechanisms, offers significant potential for enhancing the aerodynamic efficiency and performance of unmanned aerial systems (UAS). Despite these benefits, its adoption has been hindered by complexities in design, manufacturing, and installation, particularly when compared to traditional flap systems. This research explores the design, fabrication, and integration of morphing control surfaces for small-scale UAS using additive manufacturing techniques. To reduce costs and streamline the design process, fused deposition modeling (FDM) additive manufacturing was employed for component fabrication. An off-the-shelf Horizon Sport Cub S2 served as the testing platform, modified with a …

Kwad - Ksu All Weather Autonomous Drone, Nick Farinacci, Sebastian Gomez, Stewart Baker, Ed Sheridan

Symposium of Student Scholars

"KWAD" or "KSU all-Weather Autonomous Drone" project was sponsored by Ultool, LLC to the KSU Research and Service Foundation to create a lightweight drone capable of capturing HD video during all-weather operations. The conditions of all-weather operation include rainfall of one inch per hour and wind speeds of up to twenty miles per hour. In addition, a global minimum structural safety factor of two is required to ensure the system's integrity in extreme weather conditions. Potential mission profiles include autonomous aerial delivery, topological mapping in high moisture areas, security surveillance, search and rescue operations, emergency transportation of medical supplies, and …

Modeling, Control, And Hardware Development Of A Thrust-Vector Coaxial Uav, Andrew North

Doctoral Dissertations and Master's Theses

This thesis introduces a unique thrust vector coaxial unmanned aerial vehicle (UAV) configuration and presents a comprehensive investigation encompassing dynamics modeling, hardware design, and controller development. Using the Newton-Euler method, a dynamic model for the UAV is derived to gain in-depth insights into its fundamental flight characteristics. A simple thrust model is formulated and modified by comparing it with data obtained from vehicle testing. The feasibility of manufacturing such a vehicle is assessed through the development of a hardware prototype. Finally, a linear state feedback controller is designed and evaluated using the non-linear dynamics model. The results demonstrate successful validation …

Consumer 3d Printing For Remote Control Aircraft Wings: Development Of Novel Wingbox Structure, Ian Clark

University Honors Theses

Remote control aircraft construction and can be a very expensive and time-consuming hobby. With 3D printer consumer adoption rates skyrocketing, there is a gap between demand for RC aircraft and suitable well-designed models available to creators and hobbyists. By creating and testing two iterations of wingbox geometries, this research aims to help close that gap by producing an easily printable wing structure. While there are improvements that can be made on this work, this research has been effective in generating a novel wingbox structure for FFF 3D printing that has distinct advantages over other designs currently available.

3d Printed Aircraft, Matthew Nagy, Charles D'Amico, Alexis Salgado Medina

Mechanical Engineering

This project is to design, build, and test a 3D-printable aircraft. The goal is to create a final design that will be able to fly for the longest duration possible, around 20 seconds. To determine the correct preliminary design and manufacturing process for a 3D printed RC aircraft, an analysis of multiple design options and manufacturing materials was performed. This allowed for a variety of choices for aircraft type, airfoil design, structure, among other topics to be narrowed down to the most promising option. It has been found that the aircraft will follow a design similar to industry motor-gliders, with …

Dji Drone Modification, Sean Lacey, Seth Mancuso, Bryce Mckenzie

Williams Honors College, Honors Research Projects

For this project, we set out to create a lightweight carrying case that would be mounted to a DJI Phantom 3. This case is designed to transport small packages, such as medications, from a delivery vehicle to their final destination. Based on our maximum drone lifting capacity of 600 grams, our case, servomotor, and contents had to weigh less than or equal to that value. The coronavirus pandemic has led to an increase in contactless delivery options along with the push for immunocompromised people to avoid contact with people that may be sick. Our product would help transport necessary supplies …

Design Of Banner Tow Mechanism For Bush Plane, Kyle Ciarrone, Ivan Martin, Rishabh Gadi, Tyler Brandt

Williams Honors College, Honors Research Projects

The 2019-2020 AIAA DBF objective was to design, build, and test a banner-towing bush plane that carries wooden passengers and luggage. Senior members on the team undertook the creation of the banner tow mechanism subsystem as their senior design project on behalf of the design team due to the challenge of its mechanical design and the aerodynamic considerations regarding its placement and enclosure aboard the aircraft. The competition as well as access to campus resources were canceled due to COVID-19, so full testing and integration of the mechanism was not achieved. However, the engineering design process was experienced from the …

Redesign And Analysis For Landing Gear Components, Daniel Clarke

Williams Honors College, Honors Research Projects

A project for Collins Aerospace, the company I co-op at, where I will redesign several components of a landing gear for a military program. Any structural/stress analysis will also be performed. The goal is to reduce weight while maintaining strength and structural integrity.

Real Time And High Fidelity Quadcopter Tracking System, Tyler Mckay Hall

Computer Engineering

This project was conceived as a desired to have an affordable, flexible and physically compact tracking system for high accuracy spatial and orientation tracking. Specifically, this implementation is focused on providing a low cost motion capture system for future research. It is a tool to enable the further creation of systems that would require the use of accurate placement of landing pads, payload acquires and delivery. This system will provide the quadcopter platform a coordinate system that can be used in addition to GPS.

Field research with quadcopter manufacturers, photographers, agriculture and research organizations were contact and interviewed for information …

Deployable Antenna For Cubesat, Mackenzie Thomas Lennon, Caleb Andrew Barber, David Matthew Galves

Mechanical Engineering

This project is a proof-of-concept ground model of a large deployable antenna designed for the small space requirements of CubeSats. This small deployment module is designed to fit a 2 m by 1 m reflective antenna inside a storage volume of with the dimensions 20 cm by 20 cm x 40 cm. The reflector will be deployed to a parabolic shape with the goal of modeling the reflector necessary for high frequency communication. Because this module is designed as a proof-of-concept for the deployable parabolic reflector specifically, no electrical components will be incorporated and will just focus on the deployment …

Human Powered Helicopter: Rotor Structure, Joseph Ram, Juan Carlos Olvera

Mechanical Engineering

The following report encompasses the Human Powered Helicopter Rotor Team’s conceptual models and ideas based on research and modeling analysis. The following gives an overview of material researched, concept generation, analyzation, manufacturing, and testing for a rotor structure to be installed in a Human Powered Helicopter.

Cal Poly Human Powered Helicopter, Josiah Auer, Eric Behne, Dave Berry, Rebecca Hennings, James Koch, Ian Marquardt, Josiah Mayfield, Sean Miller

Mechanical Engineering

The following report encompasses the Cal Poly Human Powered Helicopter team’s efforts during the 2010-2011 academic year. The intention of this project is to further the knowledge of human powered helicopter design and to validate an ideal configuration through experimental tests and analysis. 

A. Background

The Sikorsky Prize offered by the American Helicopter Society has been the catalyst for many attempts at Human Powered Helicopter (HPH) flight. The requirement to win the prize is a continuous, human powered flight of more than 60 seconds that stays within a 10 meter square box and reaches an altitude greater than 3 meters …