Aeronautical Vehicles Commons^™

Aerodynamic And Acoustic Modeling For Evtol Rotor Noise Prediction, Daniella Bezuidenhout, Anastasios S. Lyrintzis, Vladimir V. Golubev

Doctoral Dissertations and Master's Theses

This thesis presents the development and validation of a methodology for predicting total acoustic emissions from a one-fifth scale electric vertical takeoff and landing (eVTOL) rotor in both hover and edgewise flight conditions. The approach couples sectional two-dimensional Reynolds-Averaged Navier-Stokes (2D-RANS) airfoil simulations with rotor loading predictions from the Comprehensive Hierarchical Aeromechanics Rotorcraft Model (CHARM), tonal noise calculations using the acoustic solver PSU-WOPWOP, and broadband noise predictions from the UCD-QuietFly framework. Boundary-layer inputs traditionally obtained from the viscous-inviscid solver, XFOIL, were replaced with higher-fidelity 2D-RANS results from OpenFOAM to better capture low-Reynolds-number flow physics, including laminar-turbulent transition and laminar separation …

Performance Of Adaptive Wingtips On A Tailless Supersonic Business Jet, Khushi Piparava

2025 Fall Honors Capstones Projects - Archive

The growing interest in supersonic business travel has renewed focus on efficient, low-drag configurations that can achieve high performance while maintaining stability and structural integrity. This research investigates the aerodynamic and structural implications of adaptive folding wingtips on a tailless supersonic business jet (SBJ) concept designed under the SkyBreaker senior design program. Using a conceptual aerodynamic model based on linearized supersonic theory, the Polhamus leading-edge suction analogy, and an empirical compression-lift correlation, the study evaluates how varying wingtip droop angles influence lift, drag, lift-to-drag ratio (L/D), and static stability. The analysis was performed parametrically in MATLAB, using geometry inputs derived …

High-Fidelity Modeling Of Evtol Rotor Unsteady Aerodynamic And Aeroacoustic Response To Time-Harmonic Gust, Vadim Voropayev

Doctoral Dissertations and Master's Theses

The rapid emergence of Urban Air Mobility (UAM) demands accurate prediction and mitigation of noise generated by electric vertical take-off and landing (eVTOL) aircraft operating in complex urban environments. Among the various noise sources, the aerodynamic and acoustic response of rotors to unsteady inflow represents a major uncertainty in community-noise assessment and certification. This thesis investigates the aerodynamic and aeroacoustic behavior of a representative eVTOL rotor subjected to time-harmonic inflow disturbances, providing a detailed numerical framework to quantify how periodic gusts influence rotor performance, unsteady loading, and sound radiation.

The study employs a three-stage computational methodology using the open-source solver …

Mission-To-Designs: Automating Uav Conceptual Design Generation, Nana A. Adjei

All Theses

The conceptual design stage of Unmanned Aerial Vehicles (UAVs) is an exploratory phase where designers are tasked with developing and evaluating a wide range of viable design concepts, considering different geometries and configurations based on mission requirements. The goal is to identify the most suitable design after the exploration for further development and progression to the next phase. Several tools and frameworks have been developed to assist designers in this stage, each offering unique capabilities, but all with the common aim of aiding in the efficient development and evaluation of conceptual designs. This is important in the UAV design process …

Parametric Optimization Of A Wing-Fuselage System Using A Vorticity-Based Panel Solver, Chino Cruz

Master's Theses

Aerodynamic topology optimization is a useful tool in the aerodynamic design pro-
cess, especially when looking for marginal gains within a design. One example is
a turboprop racer concept aircraft that is designed with the goal of breaking world
speed records. An optimization framework was developed with the intention of later
being applied to this design. In the early design stages, the optimization framework
must focus on quicker methods of drag estimation, such as a panel codes. The large
number of design variables in topology optimization can exponentially increase func-
tion evaluations and thus computational cost. A vorticity-based panel solver …

Innovation For The Air: A Brief History Of Worldwide Aviation, Lauren Plumley

Honors Program: Senior Projects (Public)

The purpose of this report is to present a brief but comprehensive overview of the variety of innovations related to aviation, and to discuss their impact on scientific progress over the course of human history. Relevant discoveries from the fields of physics and aerodynamics, and the numerous technologies built based upon these discoveries, are discussed over a period ranging from ancient times to the twenty-first century. The scope of this report is an overview of the development of powered and unpowered aircraft, including lighter-than-air, heavier-than-air, and aerospace technologies. Aviation developments were generally not limited to one specific country or person, …

Aeroelastic Analysis Of Small-Scale Aircraft, Kent Roberts

Master's Theses

The structural design of flight vehicles is a balancing act between maximizing loading capability while minimizing weight. An engineer must consider not only the classical static structural yielding failure of a vehicle, but a variety of ways in which structural deformations can in turn, affect the loading conditions driving those deformations. Lift redistribution, divergence, and flutter are exactly such dynamic aeroelastic phenomena that must be properly characterized during the design of a vehicle; to do otherwise is to risk catastrophe. Relevant within the university context is the design of small-scale aircraft for student projects and of particular consideration, the DBF …

Design And Flight-Path Simulation Of A Dynamic-Soaring Uav, Gladston Joseph

Doctoral Dissertations and Master's Theses

We address the development of a dynamic-soaring capable unmanned aerial vehicle (UAV) optimized for long-duration flight with no on-board power consumption. The UAV’s aerodynamic properties are captured with the integration of variable fidelity aerodynamic analyses. In addition to this, a 6 degree-of-freedom flight simulation environment is designed to include the effects of atmospheric wind conditions. A simple flight control system aids in the development of the dynamic soaring maneuver. A modular design paradigm is adopted for the aircraft dynamics model, which makes it conducive to use the same environment to simulate other aircraft models. Multiple wind-shear models are synthesized to …

Computational Investigation Of Perforated Plate Film Cooling Utilizing Conjugate Heat Transfer, Jonathan Sippel

Doctoral Dissertations and Master's Theses

The accuracy of modern state-of-practice computational fluid dynamics approaches in predicting the cooling effectiveness of a perforated plate film-cooling arrangement is evaluated in ANSYS Fluent. A numerical investigation is performed using the Reynolds Averaged Navier Stokes equations and compared to NASA Glenn’s available Turbulent Heat Flux 4 experimental measurements collected as a part of the Transformational Tools and Technologies Project. A multiphysics approach to model heat conduction through the solid geometry is shown to offer significant improvements in wall temperature and film effectiveness prediction accuracy over the standard adiabatic wall approach. Additionally, localized gradient-based grid adaption is analyzed using the …

Aerodynamic And Performance Analysis Of A Morphing Helicopter Rotor System, Vinay Gopal Krishnan

Doctoral Dissertations and Master's Theses

The purpose of this study was to investigate the effect of rotor morphing, specifically variable rotor speed and variable blade twist, on various parameters such as the distribution of angle of attack, lift, power, thrust and/or other metrics describing the performance of a helicopter rotor. A MATLAB based blade element theory model was developed and executed for different flight conditions. The model was validated against the flight test data of a UH-60. Effects on power, lift to drag ratio and rotor drag from variations in blade twist, rotor speed, rotor radius and blade chord was analyzed. Morphing cases were applied …

Wing Deflection Analysis Of 3d Printed Wind Tunnel Models, Matthew G. Paul

Master's Theses

This work investigates the feasibility of producing small scale, low aerodynamic loading wind tunnel models, using FDM 3D printing methods, that are both structurally and aerodynamically representative in the wind tunnel. To verify the applicability of this approach, a 2.07% scale model of the NASA CRM was produced, whose wings were manufacturing using a Finite Deposition Modeling 3D printer. Experimental data was compared to numerical simulations to determine percent difference in wake distribution and wingtip deflection for multiple configurations.

Numerical simulation data taken in the form of CFD and FEA was used to validate data taken in the wind tunnel …

Lift & Drag Reductions On Iced Wings During Take Off And Landing With Unmanned Aerial Vehicles, Ian R. Mcandrew

Publications

This research paper addresses an novel problem that has not been addressed in detail for many decades. Ice formation on aircraft has procedures and protocols to deal with expected and actual problems. Complex modern aircraft are equipped with a variety of techniques to remove Ice formation on an aircraft, especially the wings. The introduction of Unmanned Aerial Vehicles has added an old problem, that of low speed and the lack of power to overcome losses in lift through ice formation. In this research the different types of Ice formation, how they combine and affect Lift and Drag are also addresses …

Aerodynamic Trade Study Of Compound Helicopter Concepts, Julian Roche

Doctoral Dissertations and Master's Theses

The relative performance attributes of compound helicopter concepts have been examined, including their potential for meeting the requirements of several challenging mission profiles. For each concept, which included lift and/or propulsive compounding, a suite of aerodynamic performance models was developed using energy methods. In the case of a lift-compounded concept, an aerodynamic model representing the force interaction effects of the main rotor wake with the wing was also developed. Models of a conventional helicopter and of a tiltrotor were implemented as well, and the results used as a datum for comparison. In each case, the predictive capabilities of the model …

Book Review: High G Flight - Physiological Effects And Countermeasures, Stefan Kleinke

International Journal of Aviation, Aeronautics, and Aerospace

This review provides insight on the content and a review of the quality of the recent release of High G Flight - Physiological Effects and Countermeasures from Ashgate Publications.

This review does not reflect the views of IJAAA or ERAU. This work was not peer reviewed.

High G Flight - Physiological Effects and Countermeasures

Aerodynamic And Structural Design Of A Winglet For Enhanced Performance Of A Business Jet, Nicolas El Haddad

Doctoral Dissertations and Master's Theses

The preliminary design of a winglet to improve the range and fuel burn of the Falcon 10 business jet is presented. Twelve candidate geometries were studied varying the cant angle and the span. The configuration offering the best compromise between induced drag reduction, profile drag increase and weight increase due to the winglet structure and necessary wing structural reinforcement was selected. More refined analysis was performed for that winglet with Reynolds averaged Navier-Stokes computational fluid dynamics and finite element analysis. Range and fuel burn were finally calculated for a typical mission using these refined results. The selected winglet, with a …

Design And Performance Of Circulation Control Geometries, Rory Martin Golden

Master's Theses

With the pursuit of more advanced and environmentally-friendly technologies of today’s society, the airline industry has been pushed further to investigate solutions that will reduce airport noise and congestion, cut down on emissions, and improve the overall performance of aircraft. These items directly influence airport size (runway length), flight patterns in the community surrounding the airport, cruise speed, and many other aircraft design considerations which are setting the requirements for next generation aircraft. Leading the research in this movement is NASA, which has set specific goals for the next generation regional airliners and has categorized the designs that meet the …

Designing The Human-Powered Helicopter: A New Perspective, Gregory Hamilton Gradwell

Master's Theses

The concept of human-powered vertical flight was studied in great depth. Through the manipulation of preexisting theory and analytical methods, a collection of design tools was created to expediently conceptualize and then analyze virtually any rotor. The tools were then arranged as part of a complete helicopter rotor design process. The lessons learned as a result of studying this process—and the tools of which it consists—are presented in the following discussion. It is the belief of the author that by utilizing these tools, as well as the suggestions that accompany them, future engineers may someday build a human-powered helicopter capable …

Cfd As Applied To The Design Of Short Takeoff And Landing Vehicles Using Circulation Control, Tyler M. Ball

Master's Theses

The ability to predict the distance required for an aircraft to takeoff is an essential component of aircraft design. It involves aspects related to each of the major aircraft systems: aerodynamics, propulsion, configuration, structures, and stability and control. For an aircraft designed for short takeoffs and landings (STOL), designing the aircraft to provide a short takeoff distance, or more precisely the balanced field length (BFL), often leads to the use of a powered lift technique such as circulation control (CC). Although CC has been around for many years, it has never been used on a production aircraft. This is in …

Computation Of The Aerodynamic Characteristics Of A Subsonic Transport Aircraft Using A Panel Method, Lillianne Plaster Whitelock Troeger

Mechanical & Aerospace Engineering Theses & Dissertations

An advanced low-order panel method, VSAERO, is applied to a full-configuration transport aircraft. Wing pressure distributions as well as lift, drag, and pitching moment coefficients calculated for the full computational configuration are compared with experimental data. In addition, partial configurations are evaluated computationally to determine the relevance of certain complex aircraft components to the computations. It is shown that the wing-surface pressure distributions and pitching moment coefficient are well predicted by VSAERO. The lift coefficient is consistently overpredicted by the code.