Aeronautical Vehicles Commons^™

Reconfigurable Python Autopilot Software For Rc Aircraft, Kate Doiron

Honors Theses

No abstract provided.

Experimental And Numerical Analysis Of Laminar And Transitional Flow Through Annular Corrugated Pipes, Joseph Russell Sargent

Theses and Dissertations

This dissertation presents studies on pressure loss through annular corrugated pipes to determine a friction factor coefficient using nitrogen. Ten different corrugated pipes’ geometries were evaluated via testing and experimentation. The ratio of corrugation height to inner diameter varied from 0.233 to 0.333 and the ratio of corrugation pitch to inner diameter varied from 0.181 to 0.446. Nitrogen flow rates between 0.25 to 94.4 standard liters per minute were used, resulting in Reynolds numbers, based on the corrugated pipe inner diameter, from 100 to 23,000. The experimental set-up was validated using smooth-pipe pressure loss measurements and the derived friction factor …

Comprehensive Review And Development Of A High-Pressure Hydraulic Impedance Tube For Vibroacoustic Attenuator Characterization, Matthew D. Beals

Dissertations, Master's Theses and Master's Reports

This research establishes a versatile test bench for characterizing hydraulic vibroacoustic attenuators. The primary evaluation metric is the transfer matrix, determined experimentally, with an emphasis on key properties such as transmission loss. To ensure accuracy and broad applicability, the methodology is based on industry-standard techniques for determining the transfer matrix. A comprehensive literature review consolidates existing approaches for hydraulic attenuator characterization. The test bench features a hydraulic impedance tube equipped with eight dynamic pressure transducer (DPT) taps strategically positioned before and after the sample interface. This setup accommodates arbitrary samples terminated with standard hydraulic fittings. Using ASTM E2611, the transfer …

Modeling, Control, And Hardware Development Of A Thrust-Vector Coaxial Uav, Andrew North

Doctoral Dissertations and Master's Theses

This thesis introduces a unique thrust vector coaxial unmanned aerial vehicle (UAV) configuration and presents a comprehensive investigation encompassing dynamics modeling, hardware design, and controller development. Using the Newton-Euler method, a dynamic model for the UAV is derived to gain in-depth insights into its fundamental flight characteristics. A simple thrust model is formulated and modified by comparing it with data obtained from vehicle testing. The feasibility of manufacturing such a vehicle is assessed through the development of a hardware prototype. Finally, a linear state feedback controller is designed and evaluated using the non-linear dynamics model. The results demonstrate successful validation …

Noise Reduction Techniques In Commercial Aircraft Cabins, Hashem Hashem

Student Works

Main sources of noise heard inside an aircraft cabin:

• Engines
• Airframe & control surfaces
• Window vibrations
• Passenger announcements & activities.

Optimal Path Planning For Aerial Robots Using Genetic Algorithm, Anna Puigvert I Juan

Graduate Theses, Dissertations, and Problem Reports (ETD)

This thesis presents a path optimization solution for a robot in two different constrained 3-dimensional (3D) environments. The robot is required to travel from its current position to a goal position following minimum cost paths (optimal paths). The first environment has 3D obstacles that interfere with the robot’s path. The path cost for this environment accounts for the minimum distance traveled by the robot from the start to the goal position while avoiding obstacles. The second environment is the atmosphere of Venus, specifically a flyable region of this atmosphere with characteristics similar to Earth’s. This environment has strong westward winds …

Understanding The Nonlinear Dynamics Governing Vertical-Lift Vehicles With Variable-Speed, Fixed Rotors, Stephanie Vavra, Micah Busboom, Aleea Stanford, Keegan Moore

UNL Student Research Days Posters, Undergraduate

Problem: Traffic significantly limits travel in urban areas. • The NASA Urban Air Mobility Project is developing an air taxi as an alternative mean of transportation (Fig. 1).

Challenge: Operating rotors at different frequencies may cause the cabin to vibrate at high amplitudes. Such effects are currently unknown.

Objective: Understand the effect of variable speed rotors on passenger comfort.

From the reduced-order modeling simulations, it can be assumed that counteracting the rotor speed in-balances can reduce the displacement and vibrations experienced at the center of the wing. In other words, should a rotor not maintain its optimal operation speed, reducing …

Immunity-Based Framework For Autonomous Flight In Gps-Challenged Environment, Mohanad Al Nuaimi

Graduate Theses, Dissertations, and Problem Reports (ETD)

In this research, the artificial immune system (AIS) paradigm is used for the development of a conceptual framework for autonomous flight when vehicle position and velocity are not available from direct sources such as the global navigation satellite systems or external landmarks and systems. The AIS is expected to provide corrections of velocity and position estimations that are only based on the outputs of onboard inertial measurement units (IMU). The AIS comprises sets of artificial memory cells that simulate the function of memory T- and B-cells in the biological immune system of vertebrates. The innate immune system uses information about …

Active Permanent Magnet Attitude Control For Cubesats Using Mu-Metal Shielding, Maxwell Martin

Mechanical Engineering Undergraduate Honors Theses

Cube-Satellites (CubeSats) are nanosatellites composed of cube shaped units, each nominally 10cm to a side and around 1kg in mass. Due to their inherent size and weight limitations, it is often impractical to use conventional attitude, or rotational, control methods such as thrusters on these small satellites. Several methods, including magnetorquer rods and small reaction wheels, are often used instead of traditional methods to work around the size and weight limitations. As a new alternative to these methods, a permanent magnet mounted on a rotatable shaft could be used to achieve attitude control. In much the same way that a …

Filtered-Dynamic-Inversion Control For Fixed-Wing Unmanned Aerial Systems, Jon Mullen

Theses and Dissertations--Mechanical and Aerospace Engineering

Instrumented umanned aerial vehicles represent a new way of measuring turbulence in the atmospheric boundary layer. However, autonomous measurements require control methods with disturbance-rejection and altitude command-following capabilities. Filtered dynamic inversion is a control method with desirable disturbance-rejection and command-following properties, and this controller requires limited model information. We implement filtered dynamic inversion as the pitch controller in an altitude-hold autopilot. We design and numerically simulate the continuous-time and discrete-time filtered-dynamic-inversion controllers with anti-windup on a nonlinear aircraft model. Finally, we present results from a flight experiment comparing the filtered-dynamic-inversion controller to a classical proportional-integral controller. The experimental results show …

Development Of A Pyrotechnic Shock Simulation Apparatus For Spacecraft Applications, Joseph Binder, Matthew Mccarty, Chris Rasmussen

Aerospace Engineering

This report details the research, design, construction, and testing of a pyrotechnic shock simulation apparatus for spacecraft applications. The apparatus was developed to be used in the Space Environments Lab at California Polytechnic State University. It will be used for testing spacecraft components with dimensions up to 24”x12”x12” as well as CubeSats. Additionally, it may be used as an instructional or demonstrational tool in the Aerospace Department’s space environments course. The apparatus functions by way of mechanical impact of an approximately 20 lb stainless steel swinging hammer. Tests were performed to verify the simulator’s functionality. Suggestions for improvement and further …

Human Powered Helicopter: Rotor Structure, Joseph Ram, Juan Carlos Olvera

Mechanical Engineering

The following report encompasses the Human Powered Helicopter Rotor Team’s conceptual models and ideas based on research and modeling analysis. The following gives an overview of material researched, concept generation, analyzation, manufacturing, and testing for a rotor structure to be installed in a Human Powered Helicopter.

Aerodynamics And Control Of A Deployable Wing Uav For Autonomous Flight, Michael Thamann

Theses and Dissertations--Mechanical and Aerospace Engineering

UAV development and usage has increased dramatically in the last 15 years. In this time frame the potential has been realized for deployable UAVs to the extent that a new class of UAV was defined for these systems. Inflatable wing UAVs provide a unique solution for deployable UAVs because they are highly packable (some collapsing to 5-10% of their deployed volume) and have the potential for the incorporation of wing shaping. In this thesis, aerodynamic coefficients and aileron effectiveness were derived from the equations of motion of aircraft as necessary parameters for autonomous flight. A wind tunnel experiment was performed …

Airplane Landing Flare-The Last 5 Seconds, Nihad E. Daidzic

Aviation Department Publications

No abstract provided.