Aerodynamics and Fluid Mechanics Commons^™

Analysis Of Turbulence Models As Applied To Two- And Three-Dimensional Injection Flows, Clarence R. Chenault

Theses and Dissertations

A steady state solution of the full, three dimensional Favre averaged Navier Stokes equations, coupled with a second order Reynolds stress turbulence model (RSTM) and an eddy viscosity model were used to numerically simulate oblique injection into supersonic flow. Numerical results were compared to experimental data and the turbulence models were evaluated for accurate prediction of thermomechanical mean flow variables, Reynolds stresses, flowfield shock structure and boundary layer phenomena. The RSTM simulation resulted in physically consistent and accurate predictions for the mean flow and turbulent quantities. Simulations with the eddy viscosity model resulted in non-physical and inconsistent turbulence predictions. RSTM …

Experimental Investigation Of The Influence Of Molecular Weight On Mixing And Penetration In Supersonic Dissimilar Gaseous Injection Into A Supersonic Cross-Flow, Troy A. Giese

Theses and Dissertations

In pursuit of a more efficient and effective fuel-air mixing for a SCRAMjet combustor, this study investigated relative near field effects of molecular weight on mixing and penetration of different gaseous injection into a supersonic (M=2.9) cross flow. Helium and argon gas were chosen as injectants because of the large differences in molecular weights. Also, mixing enhancement was observed by injecting the traverse gas jet parallel to the compression face of a ramp. Color schlieren photography was used to identify the shock structures and interactions in the flow field. Measurements of mean flow properties were used to establish the jet …

Flow Field And Loading Analysis On A Wrap-Around Fin Missile, Thomas C. Mcintyre

Theses and Dissertations

Wrap-around fin (WAF) missiles offer packaging benefits but experience rolling moments due to the curved fin design. Rolling moments stabilize unguided projectiles, but cause guidance and control problems for future guided applications. Understanding the flow field in the vicinity of the fins is critical to future missiles. Fin pressure profiles were characterized with pressure-sensitive paint. Two rectangular four-fin constructions were tested-one solid and one with a rectangular hole (slotted fin). Static pressure data were divided by free-stream total pressure for presentation. Tests were conducted at Mach numbers of 2.15, 2.28, 2.41, 2.86, 3.25, 3.50 and 3.83. Reynolds numbers based on …

Aerodynamic Gradient-Based Optimization Using Computational Fluid Dynamics And Discrete Sensitivities For Practical Problems, Mohagna Jayendrarai Pandya

Mechanical & Aerospace Engineering Theses & Dissertations

A gradient-based shape optimization methodology based on quasi-analytical sensitivities has been developed for practical three-dimensional aerodynamic applications. The flow analysis has been rendered by a fully implicit, finite-volume formulation of the Euler and Thin Layer Navier-Stokes (TLNS) equations. The flow equations and aerodynamic sensitivity equation have been solved using an alternating-direction-implicit (ADI) algorithm for memory efficiency. A wing geometry model based on space-surface and planform parameterization has been utilized. The present methodology and its components have been tested via several comparisons.

Initially, the inviscid flow analysis for a wing has been compared with those obtained using an unfactored, Preconditioned Conjugate …

Three-Dimensional Aerodynamic Design Optimization Using Discrete Sensitivity Analysis And Parallel Computing, Amidu Olawale Oloso

Mechanical & Aerospace Engineering Theses & Dissertations

A hybrid automatic differentiation/incremental iterative method was implemented in the general purpose advanced computational fluid dynamics code (CFL3D Version 4.1) to yield a new code (CFL3D.ADII) that is capable of computing consistently discrete first order sensitivity derivatives for complex geometries. With the exception of unsteady problems, the new code retains all the useful features and capabilities of the original CFL3D flow analysis code. The superiority of the new code over a carefully applied method of finite-differences is demonstrated.

A coarse grain, scalable, distributed-memory, parallel version of CFL3D.ADII was developed based on "derivative stripmining". In this data-parallel approach, an identical copy …

Numerical And Experimental Investigation Of The Flowfield Near A Wrap-Around Fin, Carl P. Tilmann

Theses and Dissertations

A wall-mounted semi-cylindrical model fitted with a single wrap-around fin (WAF) has been investigated both numerically and experimentally, with the objective of characterizing the mean and turbulent flowfield in the vicinity of the fin. Numerical and experimental results are used to determine the nature of the flowfield and quantify the effects of fin curvature on the character of the flow near WAFs. This research has been motivated by the need to identify possible sources of a rolling moment reversal observed at high speeds in sub-scale flight tests. Detailed mean flow and turbulence measurements were obtained in the AFIT Mach 3 …

A Feasibility Study Of Fuel Cell Cogeneration In Industry, Scott B. Phelps, J. Kelly Kissock

Mechanical and Aerospace Engineering Faculty Publications

Up until now, most of the literature on fuel cell cogeneration describes cogeneration at commercial sites. In this study, a PC25C phosphoric acid fuel cell cogeneration system was designed for an industrial facility and an economic analysis was performed. The US DOE Industrial Assessment Center (IAC) database was examined to determine what industry considers a good investment for energy saving measures. Finally, the results of the cogeneration analysis and database investigation were used to project the conditions in which the PC25C might be accepted by industry.

Analysis of IAC database revealed that energy conservation recommendations with simple paybacks as high …

Experimental Investigation Of Compressible Boundary Layers Under The Influence Of Pressure Gradients, Raymond C. Wier

Theses and Dissertations

This study examined the effect of mild pressure gradients on the mean and turbulent flow of high-speed boundary layers. Three Mach numbers (1.7, 3.0 and 5.0) were investigated. Three pressure gradients were examined; a zero pressure gradient (ZPG), a favorable pressure gradient (FPG), and a combined pressure gradient (CPG). The CPG consisted of an adverse pressure gradient followed by a favorable pressure gradient. Conventional pressure probes, hot-wire and particle image velocimetry (PIV) were used to examine the flow. Measurement included mean velocity, velocity turbulence intensity, mass flux turbulence intensity and energy spectra. Instantaneous (10 nsec) Mie scattering flow visualizations were …

Experimental Investigation Of Transverse Supersonic Gaseous Injection Enhancement Into Supersonic Flow, Mark P. Wilson

Theses and Dissertations

In pursuit of more efficient and effective fuel-air mixing for a SCRAMJET combustor, this study was conducted to investigate relative near field enhancements of penetration and mixing of a discrete low-angled (25°) injected air jet into a supersonic (M=2.9) cross flow. The enhancements were achieved by injecting the transverse air jet parallel to the compression face of eight different ramp geometries. The jet-ramp interactions created collinear shock structures, baroclinic torque vorticity enhancement, ramp spillage enhanced vorticity, magnus effect penetration enhancement, and increased total pressure loss. Shadowgraph photography was used to identify the shock structures and interactions in the flow field. …

The Effectiveness Of Film Cooling In A Hypersonic Flowfield With Favorable Pressure Gradients, Julie A. Young

Mechanical & Aerospace Engineering Theses & Dissertations

The impetus of this technical document is to report results of aerothermodynamic cooling of a scramjet nozzle under favorable pressure gradients. The goals of film cooling are to protect the nozzle skin from the high enthalpy combustor flow, reduce regenerative cooling requirements, and decrease nozzle skin friction. A hypersonic nozzle configuration for which experimental data exists was selected as the basis of this numerical study. As a first step, the numerical results of film cooling along a flat plate are compared to previous literature to validate the numerical model. Subsequently, computations are performed to study the effects of varying the …

A Study Of The Numerical Implementation Of Multidisciplinary Design Optimization Strategies, Rodney A. Taylor

Mechanical & Aerospace Engineering Theses & Dissertations

Design optimization provides an organized, systematic, and efficient method for obtaining design improvements based upon a specified measure of design performance. In the multidisciplinary design optimization (MDO) environment efficient optimization techniques allow complex designs to be improved by managing conflicting disciplinary design goals so as to improve the global design. This thesis studies the implementation issues surrounding MDO techniques and strategies. To facilitate this investigation two testbed problems have been selected for study. These problems consider two approaches to the conceptual design of an aeroelastic wing. The first approach is based on an idealized, two-dimensional representation of an airfoil under …

Direct Measurement Of Skin Friction In High Temperature And Impulsively Started Supersonic Flowfields, David M. Hazelton

Theses and Dissertations

This study further developed and improved a miniature plastic cantilever floating element gauge for direct measurement of skin friction in shock tunnel tests. Gauge durability and usability were improved, and potential sources of error were quantified. A high frequency 30 kHz gauge (compared to the baseline 10 kHz gauge) was constructed by using an I-beam cantilever rather than a round beam. A directional gauge was developed and demonstrated by measuring the flowfield about a fin in the AFIT shock tunnel. The 10 kHz and 30 kHz gauges were used in two scramjet test sequences conducted at Mach 14 enthalpy (stagnation …

Nonlinear Analysis Of Airfoil Flutter At Transonic Speeds, Scott A. Morton

Theses and Dissertations

Hopf-bifurcation analysis is used to determine flutter boundaries of a pitch and plunge airfoil (PAPA) at transonic Mach number conditions. The PAPA model is a coupling of the Euler equations and a two-degree-of-freedom structural model composed of linear and torsional springs. The Euler equations are discretized using an upwind total variation diminishing scheme (TVD) of Harten and Yee. Equilibrium solutions of the PAPA model are computed using Newton's method and dynamic solutions are explicitly integrated in time with first-order accuracy. The Hopf-bifurcation point, which models the flutter condition, is computed directly by solving an extended system of equilibrium equations following …

Sensitivity Analysis And Optimization Of Aerodynamic Configurations With Blend Surfaces, Almuttil Mathew Thomas

Mechanical & Aerospace Engineering Theses & Dissertations

A novel (geometrical) parametrization procedure using solutions to a suitably chosen fourth order partial differential equation is used to define a class of airplane configurations. Inclusive in this definition are surface grids, volume grids, and grid sensitivity. The general airplane configuration has wing, fuselage, vertical tail and horizontal tail. The design variables are incorporated into the boundary conditions, and the solution is expressed as a Fourier series. The fuselage has circular cross section, and the radius is an algebraic function of four design parameters and an independent computational variable. Volume grids are obtained through an application of the Control Point …

Study Of Surface Heat Exchangers For High-Altitude Atmospheric Research Aircraft, Te-Kang Wang

Mechanical & Aerospace Engineering Theses & Dissertations

A flush-mounted heat exchanger concept, using the wing surface to dissipate heat, is investigated as a lower drag alternative to conventional ducted plate-fin radiators. A feasibility analysis is made for an unmanned high-altitude aircraft which will reach altitudes up to 25 kilometers. A computer code is used to calculate approximate heat transfer coefficients over the airfoil's surface. A model is tested in the Old Dominion University subsonic wind tunnel to verify the results of the computer code. The results indicate that a flush mounted heat exchanger design is able to provide 20 to 100 percent of the required heat dissipation …

An Investigation Into The Effects Of Lateral Aerodynamic Asymmetries, Lateral Weight Asymmetries, And Differential Stabilator Bias On The F-15 Directional Flight Characteristics At High Angles Of Attack, David R. Evans

Theses and Dissertations

The F-15 is a stable aircraft throughout most of its flight envelope. However, it still exhibits an uncommanded yawing and rolling tendency at high angles-of-attack. Identified influencing factors of this uncommanded motion are lateral aerodynamic asymmetries, lateral weight asymmetries, and differential stabilator bias. Previous research into the effects of these influencing factors has been qualitative. This thesis quantifies the effects and then identifies a symmetric F-15 configuration. The quantifying metric presented is net yaw acceleration. This thesis used both computer simulation and experimental flight test to quantify these effects. A discussion of each influencing factors effects on the F-15B high …

Compressible Turbulence Measurements In A Supersonic Boundary Layer With Impinging Shock Wave Interaction, Michael J. Meyer

Theses and Dissertations

No abstract provided.

Riblet Effects On Gortler Vortex Development Over A Concave Surface, James A. Rothenflue

Theses and Dissertations

Riblet effects on Goertler vortex development in laminar and transitional flows were measured using three-dimensional laser-Doppler anemometry. Three freestream velocities were tested such that riblet spacing corresponded to Goertler vortex (GV) wavelengths which presumably would be either strongly amplified, weakly amplified, or attenuated by centrifugal forces on a curved surface. Experiments revealed the development of paired, counterrotating vortices within the riblet valleys over both flat and concave surfaces. For riblet spacings equivalent to weakly or non-amplified GV wavelengths, GV development on a curved surface was above the riblets and was delayed by the addition of riblets. The GV wavelength was …

An Experimental Investigation Of A Sting-Mounted Finite Circulation Control Wing, Lorenzo C. Bradley Iii

Theses and Dissertations

This study investigated the lift, drag and pitching moment performance of a circulation control wing in the AFIT 5-ft wind tunnel. The experimental wing model was a 20 percent thick, 8.5 percent camber, partial elliptical cross-section, single blowing slot, rectangular planform wing. The aspect ratios tested were 3.99, 3.77 and 3.75. The variables in the investigation included the slot blowing rate and model configuration. The model was modified by adding a leading edge nose droop, a trailing edge splitter plate and wing tip fences to improve flow at the leading edge, reduce separation effects, and encourage attached flow on the …

Influence Of A Moving Endwall On The Tip Clearance Vortex In An Axial Compressor Cascade, Lawrence J. Peter

Theses and Dissertations

This experiment involved the design, construction, validation and testing of a new facility for the investigation of vortices generated by compressor rotor blade tip clearance with a moving endwall. A five-tube pressure rake placed downstream of the trailing edge of a cascade of blades measured the pressure field for flow coefficients ranging from 20 to 1.66 and tip clearances of 0.33, 1.0, 1.7 and 2.4 percent chord. Contour plots of mass averaged pressure loss coefficient appear to show the no-flow tip vortex becomes entrained and diffused by the moving wall boundary layer. The high loss region near the moving wall …

Investigation Of Aerodynamic Alterations For Improving The Kc-135 Boom Performance During Aerial Refueling, Debra A. Nawrocki

Theses and Dissertations

This study investigated the eligibility of the KC-135 air refueling boom for improved capabilities in the areas of control and performance. By using a thick airfoil cross-section for the boom tube, rather than the current circular cross-section, the ability to increase the lift characteristics was verified Prior compiled test data was used for comparison against analytical computer solutions. The possibility and effects of control frequency oscillations were also examined due to the unstable nature of the flow at test conditions. Additionally, the effect of other cross-section shapes, such as the blunt fairing, on the size of the flyable envelope for …

Experimental Investigation Of Non-Adiabatic Supersonic Slot Injection Into A Supersonic Cross-Flow, Kelly C. Tucker

Theses and Dissertations

Turbulence and mean flow measurements were acquired downstream of a normal, supersonic (M=1.6), two-dimensional, slot injection into Mach 3.0 flow (Re/m = 15x10⁶). Two non-adiabatic cases T_i/T_∞ = 1.11 and T_i/T_∞ = 0.93) were studied. Multiple overheat anemometry and conventional mean flow analysis, as well as shadowgraph and schlieren photography, were utilized to study the turbulent mixing layer. The mean flow data included the Pitot, cone-static, and Mach number profiles. The measured turbulence data included shear stresses, mass flux, total temperature turbulence intensities, and turbulent heat fluxes. The temperature and density variation …

Numerical Simulation Of Supersonic Turbulent Boundary Layer Flow Under The Influence Of Mild Pressure Gradients, Eric T. Fick

Theses and Dissertations

Mach 2.9 boundary layer flow (R_e/m ≈ 1.75x10⁷) under the influence of mild pressure gradients is studied numerically. Baldwin-Lomax and k - ω turbulence models are incorporated into a cell centered finite volume flow solver and the results are compared with hot wire anemometry and Laser Doppler Velocimetry (LDV) measurements obtained for the same geometries in the AFIT Mach 2.9 wind tunnel. Agreement between the present simulations obtained with the k - ω turbulence model and experimental velocity profiles is excellent in all test sections. Nondimensional turbulent shear stress predictions closely match experimental data in the …

Experimental Investigation Of A Supersonic Turbulent Boundary Layer With Adverse Pressure Gradient, Chad S. Hale

Theses and Dissertations

Laser Doppler Velocimetry (LDV) measurements were made to quantify the effect of adverse pressure gradient on the compressible turbulent flow structure in a Mach 2.9 boundary layer (Re/m= 1.75 x 10⁷). Measurements included profiles of 2-D mean velocities, turbulence intensities, Reynolds shear stresses, intermittency, flatness and skewness. In addition, mean strain rates were also measured. The boundary layer measurements were acquired for both flat plate and compression ramp models. LDV measurements were made at two locations on the compression ramp model at 68 cm and 71 cm downstream of the nozzle throat. At these locations, Β …

Mach 2.9 Investigation Into The Flow Structure In The Vicinity Of A Wrap-Around Fin, Richard E. Huffman Jr.

Theses and Dissertations

A ceiling-mounted semi-cylindrical model containing a single wrap-around fin (WAF) was tested in the AFIT Mach 2.9 test facility. Flow visualization using oil- low streaklines, schlieren images and shadowgraph photography revealed a A-shock at the fin-body juncture and the development of an asymmetric bow-shock about the fin. Quantitative measurements were taken with a 100 cone-static pressure probe, a Pitot pressure probe and two cross-wire hot-film probes (u-v and u-w components, respectively). Measurements were made at cutting-planes from the inlet of the test section to aft of the model, with emphasis placed in the vicinity of the WAF. Results include cutting-plane …

Compressible Turbulence Measurement In The Mixing Layer Of An Adiabatic Normal Slot Injection Into Supersonic Flow, Christopher D. Whitcomb

Theses and Dissertations

In this study mean flow and compressible turbulence measurements were taken at a station x = 72W downstream of the injection, where W is the injector throat width, of an adiabatic 2-D Mach 1.6 normal slot injection into a Mach 2.9 flow. Data were collected using a conventional Pitot probe, a cone-static probe, and multiple overheat cross-wire anemometry. In addition, schlieren and shadowgraph flow visualization was used to investigate the flow structure at both the injection point and at the downstream data collection point. From these measurements, mass flux component turbulence intensities of 8% to 10% were seen. The total …

Development And Testing Of A New Optimum Design Code For Hypersonic Wind Tunnel Nozzles, Including Boundary Layer, Turbulence, And Real Gas Effects, Ralph C. Tolle

Theses and Dissertations

A robust and efficient optimization code is developed and validated. The code is used to redesign an existing Mach 12 wind tunnel nozzle and utilizes response surface methodology (RSM) techniques. Explicit, globally second-order, flux-difference-splitting algorithms are used to solve the Navier-Stokes (NS) and Parabolized Navier-Stokes (PNS) flow solvers incorporated into the optimizer code. Either the Baldwin-Lomax or the Yang-Shih k-s turbulence model may be employed in the optimization code. First, 2-D/axisymmetric NS and PNS flow solvers are developed/modified and account for perfect gas/nonequilibrium chemically reacting flows. All solvers are validated against Computational Fluid Dynamics (CFD) and experimental data. The optimization …

Vibration Analysis Of A Split Path Gearbox, Timothy L. Krantz, Majid Rashidi

Scholarship Collection

Split path gearboxes can be attractive alternatives to the common planetary designs for rotorcraft, but because they have seem little use, they are relatively high risk designs. To help reduce the risk of fielding a rotorcraft with a split path gearbox, the vibration and dynamic characteristics of such a gearbox were studied. A mathematical model was developed by using the Lagrangian method, and it was applied to study the effect of three design variables on the natural frequencies and vibration energy of the gearbox. The first design variable, shaft angle, had little influence on the natural frequencies. The second variable, …

Wing-Section Optimization For Supersonic Viscous Flow, Cem Cihan Item

Mechanical & Aerospace Engineering Theses & Dissertations

The recent interest in the High Speed Civil Transport (HSCT) has resulted in renewed research studies of optimized supersonic cruise transport configurations. Incorporation of flow viscosity effects in the design process of such a supersonic wing is currently under investigation. This may lead to more accurate problem formulations and, in tum, greater aerodynamic efficiency than can be obtained by the traditional, inviscid, linear theories. In this context, for a design code to be a candidate for a complex optimization problem, such as three-dimensional viscous supersonic wing design, it should be validated using simpler building-block shapes.

To optimize the shape of …

Compressible Turbulence Measurement In Low-Angle Injection Into A Supersonic Flow, Gregory J. Mccann

Theses and Dissertations

Mean flow and compressible turbulence measurements have been obtained at two stations downstream of low-angle supersonic injection into a Mach 3.0 flow (Re/m = 15 x 10⁶). Data were collected using conventional Pitot and cone-static probes, single and multiple overheat cross-wire anemometry, and flow visualization techniques (shadowgraphs and schlierens). A direct measure of total Reynolds shear stress was accomplished using a turbulence transformation of the Reynolds-averaged Navier-Stokes equations. Results show compressibility effects, indicated by density fluctuations, to be large relative to the velocity fluctuations and on the same order in all three components. Compressibility appears to account for …