Engineering Physics Commons^™

Surface Resistance Measurements Of Superconducting Niobium Samples With A Triaxial Cavity, Paul Martin Boccard

Physics Theses & Dissertations

This experimental study has revealed and investigated many of the physical issues that affect accurate measurement of the surface resistance for small samples consisting of superconducting niobium films on copper substrates. It is believed that this work provides the groundwork for future research directed towards solving this important problem. Accurate measurement of surface resistance for such samples is needed to allow the rapid evaluation and optimization of the deposition parameters necessary for manufacturing low-loss superconducting niobium films.

A superconducting niobium triaxial cavity was investigated to determine its suitability for measuring the residual surface resistance of copper samples that were sputter-coated …

Computer Simulations Of Electromigration Based On A Molecular Dynamics Approach, John Stephen Peake

Electrical & Computer Engineering Theses & Dissertations

Most research on electromigration has centered around macroscopic simulations of electromigration where a value for the diffusion coefficient was assumed to be spatially uniform throughout the material. The research in this thesis goes a step further and, through microscopic molecular dynamics computer simulations, calculates and updates the atomic drift velocity and atomic position as a function of time to analyze how various defects within the conductor affect these quantities. The simulations are carried out with defects in the form of dislocation half-planes placed in different locations within the simulation space. The atomic drift velocity and position changes derived from these …

An Injection Modelocked Titanium-Sapphire Laser, James C. Hovater

Electrical & Computer Engineering Theses & Dissertations

I have investigated the possibility of using an injection modelocked Ti-sapphire laser as a illumination source for GaAs photocathodes. A commercial Ti-sapphire laser was modified to accept a seed pulse from a gain-switched diode laser. Modelocked operation was obtained through gain modulation within the Ti-sapphire crystal as a result of injection seeding with a modelocked pulse train from a gain-switched diode laser. The Ti-sapphire laser essentially becomes a pulse amplifier for the diode laser. Unlike conventional modelocked lasers, the pulse repetition rate of this laser can be discretely varied by setting the seed laser repetition rate equal to multiples of …

High Pressure Radio-Frequency Microhollow Cathode Discharges, Anja Annett Muller

Electrical & Computer Engineering Theses & Dissertations

A new field of microhollow cathode discharges is represented by the RF microhollow cathode discharge. So far, the behavior and related physical processes of the RF microhollow cathode discharge are not well investigated.

RF microhollow discharges in air at high pressures were investigated under different experimental conditions. The geometry was changed by reducing the cathode hole diameter and the dielectric spacer thickness. By adding a noble gas to air, the influence of additive gases was explored. Additionally, the parallel operation of RF microhollow discharges was investigated.

It was shown that stable RF microhollow cathode discharges could only be sustained up …

Electrical Characteristics And Parallel Operation Of Microhollow Cathode Discharges, Wenhui Shi

Electrical & Computer Engineering Theses & Dissertations

This thesis describes the electrical properties of microhollow cathode discharges with argon as filling gas. The appearance and current-voltage characteristics of microhollow cathode discharges have been recorded. Three kinds of discharge modes (predischarge, hollow cathode discharge and abnormal discharge) have been observed. The range of operation of the hollow cathode discharge has been found to be 0.5 < pD & 5 Torr cm in argon. By reducing the hole diameter to 100 pm, we were able to operate the discharge to atmospheric pressure in a dc mode. The possibility of dc parallel operation of microhollow cathode discharges was explored. Parallel operation could be obtained without individual ballast for discharges with a positive I-V slope greater than 10 V/mA over a voltage range of more than 5 % of the sustaining voltage. For parallel operation outside the range the ballasting is required. This model was explored by using a segmented anode model. The result of the simple calculation coincides well with the experiment result, where a semi-insulator silicon was used as distributed ballast.

Coupled Electrodynamic-Monte Carlo Simulations Of Nanoscale Gaas Terahertz Optical Mixers, Jiang Li

Electrical & Computer Engineering Theses & Dissertations

The concept of mixing or heterodyning has traditionally been used for microwaves and for radio frequency communications. However, the concept can easily be extended into the optical frequency regime. By doing so, the photomixing process can serve as a very versatile tool for both the generation of ultrahigh frequency (terahertz) and the detection of weak optical signals.

The aim of this thesis is to perform a theoretical study of the photomixing process inside GaAs devices as the non-linear elements. A coupled approach which combines the Monte Carlo simulation scheme for the carrier transport, with Maxwell's equation for the electrodynamics, has …

Reactions Of Oxygen And Nitric Oxide In A Microhollow Electrode Discharge, Joseph L. Desormeaux Jr.

Electrical & Computer Engineering Theses & Dissertations

Microhollow electrode discharges have been developed and researched in the Physical Electronics Research Institute Laboratories. This discharge typically operates in direct current mode. Microhollow electrode discharges are non-thermal discharges that produce electrons with energies greater than 10 electron volts. Passing gas mixtures through non-equilibrium discharges invokes excitation or dissociation of gas molecules.

The scope of my research was to study the effect of the discharge on the chemistry of two gases, oxygen and nitric oxide in nitrogen mixture. Initial experiments were performed in an effort to produce ozone near atmospheric pressure. This seemed possible since the discharge has a high-energy …

Material Evaluation By Pulsed Diode Laser Optoacoustics, Xiaodong Xu

Electrical & Computer Engineering Theses & Dissertations

Pulsed diode laser optoacoustic diagnostics were carried out to characterize solid sample materials. The apparatus developed is compact, portable, cost-effective and therefore very promising for both industrial as well as laboratory applications. To our knowledge, this is the first time that optoacoustic characterization and measurement have been performed with a diode laser. The method was successfully applied to measure the thickness of a multilayer structure non-intrusively. Internal cracks of the material were detected by this technique.

A theory for optoacoustic signal generation, propagation and detection is given. A numerical analysis technique is developed to solve for the expected signal. In …

Atomic Hydrogen Cleaning Of Inp(100) For Preparation Of A Negative Electron Affinity Photocathode, K. A. Elamrawi, M. A. Hafez, H. E. Elsayed-Ali

Electrical & Computer Engineering Faculty Publications

Atomic hydrogen cleaning is used to clean InP(100) negative electron affinity photocathodes. Reflection high-energy electron diffraction patterns of reconstructed, phosphorus-stabilized, InP(100) surfaces are obtained after cleaning at ∼400 °C. These surfaces produce high quantum efficiency photocathodes (∼8.5%), in response to 632.8 nm light. Without atomic hydrogen cleaning, activation of InP to negative electron affinity requires heating to ∼530 °C. At this high temperature, phosphorus evaporates preferentially and a rough surface is obtained. These surfaces produce low quantum efficiency photocathodes (∼0.1%). The use of reflection high-energy electron diffraction to measure the thickness of the deposited cesium layer during activation by correlating …

A Validation Of The Parameterized Real-Time Ionospheric Specification Model (Prism) Version 1.7b, Shawn D. Filby

Theses and Dissertations

The most current version of the Parameterized Real-time Ionospheric Specification Model (PRISM), version 1.7b, was validated using Digital Ionospheric Sounding System (DISS) measurements of F2 layer critical frequency (foF2) and F2 peak electron density height (hmF2) as the "ground truth." PRISM was executed, first, with no real-time input parameter and, second, with Global Positioning System (GPS) Total Electron Content (TEC) measurements as the sole real-time parameter. Hourly values of hmF2 and foF2 over 123 days in 1994-1996 (solar minimum conditions) and covering three seasons (equinox, summer solstice, and winter solstice) were compared for Wallops Island, Virginia, and Point Arguello, California, …

Selective Cvd Growth Of Diamond Crystals On Tungsten, Charles Randal Cole

Electrical & Computer Engineering Theses & Dissertations

Typical field emitters consist of sharp metal tips which usually have a short life due to erosion and contamination. To improve the performance of regular field emitters, diamond can be placed on the emitter tip. This is done by selectively growing diamond on tungsten tips using chemical vapor deposition (CVD) processing. Diamond exhibits negative electron affinity, so that electrons will be emitted by properly biasing the tip.

To obtain single crystal growth right at the tip, a cantilever controlled nucleation method was developed which worked better than other methods. Surface preparation was also important to the growth process. An oxide …

A Novel Laboratory Course On Advanced Chemical Engineering Experiments, Jochen A. Lauterbach, S. White, X. Lui, G. M. Bodner, W. N. Delgass

Faculty Publications

The chemical engineering curriculum in the United States has trained generations of technical experts who have successfully optimized chemical processes and products once they entered the chemical industry. The U.S. chemical industry, however, has entered a critical stage in which it must be able to create new and differentiated value through technical innovations that arc essential for long-term survival. This innovation process will require new skills that go far beyond the traditional expertise for the optimization of tasks possessed by young chemical engineers. The innovators must be able to identify new opportunities, explore the boundaries of technology, evaluate critical issues, …

Experimental Investigation Of Nonlinear Dynamics In Single Mode Semiconductor Laser Diodes With Phase Conjugate Feedback, Gordon T. Hengst

Theses and Dissertations

The semiconductor laser diode offers a unique system to investigate nonlinear dynamics when optical feedback is applied. Although there is extensive research of laser diodes with optical feedback from normal dielectric mirrors, very little has been done experimentally to analyze the effects of degenerate phase conjugate feedback from a BaTiO₃ crystal. This research experimentally investigated the dynamics of a single-mode laser diode with weak phase conjugate feedback using both the self-pumped and double phase conjugate geometries. The experimental results validated a mathematical model which numerically evaluates the Lang-Kobayahsi coupled differential equations. The model simulated the nonlinear behavior of a …

High Resolution Wavelength Modulation Spectroscopy For Precise Gaseous Characterization, Audra Michiele Bullock

Electrical & Computer Engineering Theses & Dissertations

Wavelength modulation spectroscopy is a highly sensitive, non-intrusive technique for probing gaseous species. Parameters such as velocity, density, and temperature can be measured and monitored with a high degree of precision. In addition, with the use of this technique multiple molecular species may be identified with a single laser probe. This measurement technique utilizes the well-known principles of modulation absorption spectroscopy in a novel way.

The research focuses on harmonic detection and the advantages gained by performing detection at higher harmonics, those greater than the commonly used second harmonic. We show that there is an increase in the sensitivity to …

Unfolding The High Energy Electron Flux From Crres Fluxmeter Measurements, Brian D. Mckellar

Theses and Dissertations

The Combined Release and Radiation Effects Satellite (CRRES) was launched on 25 July 1990 to collect measurements in the earth's radiation belts. One instrument, the High Energy Electron Fluxmeter (HEEF), measured the flux of electrons in 10 channels with energies between 1 MeV and 10 MeV. The channel sensitivities, Ri(E), have been calibrated and partially re-calibrated. We explore the errors introduced in unfolding the electron flux spectrum from the channel measurements and the propagation and growth of calibration and measurement errors. Using numerical experimentation, we fold the responses with known spectra to obtain simulated measurements, add random measurement and calibration …

Luminescence Study Of Ion-Implanted Gallium Nitride, Eric Silkowski

Theses and Dissertations

Luminescence and absorption measurements were used to demonstrate the efficacy of ion implantation for introducing various classes of dopants into GaN. A wide range of implantation and annealing studies were performed with several dopant species (Ar, Zn, C, O, Si, Be, Mg, Nd, Er). Room temperature ion implantation was performed on MOCVD- and MBE-grown GaN samples at energies between 100 and 1150 keV with doses ranging from 1 x 10¹³ to 1 x 10¹⁵/cm^-2. Conventional furnace annealing in flowing NH₃ or N₂ gas resulted in good implantation damage recovery at an annealing temperature …

Two-Dimensional Drift-Diffusion Simulations Of Silicon Avalanche Shaper (Sas) Devices For High Power Applications, Hamid Jalali

Electrical & Computer Engineering Theses & Dissertations

Silicon Avalanche Shaper devices have been projected as being important components of an inexpensive, semiconductor-based technology for high power switching applications. The primary advantage of this technology is that it is based on Silicon material which is easy to fabricate and has a well established processing technology. Unlike other high power technologies, the SAS devices do not rely on external optical triggering which eliminates the need for lasers and related optical circuitry.

The SAS based high power switching technology has been pioneered and tested by a Russian group. Though preliminary results have been very encouraging, the device reliability and its …

Electron Beam Emission From A Ferroelectric Cathode, Crystal Briana Garland

Electrical & Computer Engineering Theses & Dissertations

The electron beam emission from a LTZ-2 (lead titanate-zirconate) ferroelectric cathode was characterized. The purpose was to determine the operation range for this type of electron emitter. The experimental apparatus consisted of a high voltage driving circuit with a charging voltage up to 30kV. A solid-state SCR switch is used to generate the high voltage pulse which induces a polarization change. Current densities on the order of 80A/cm² 30kV were achieved. The electron beam profile is Guassian. At long anode-cathode distances the measured current densities were found to be above Child-Langmuir space charge limits. The large current densities and …

Frequency Response Enhancement Of A Flow Sensor Using Diamond Thin Films Synthesized By Plasma Cvd, John Curren Hagwood

Electrical & Computer Engineering Theses & Dissertations

Theoretical modeling conducted previously in our Microelectronics Laboratory has shown that a layer of diamond film inserted between a metal film and a substrate will enhance the frequency response of a conventional thin film flow sensor. This thesis involved fabricating and testing a conventional thin film sensor of nickel on quartz (Ni/Q) and a diamond enhanced sensor (Ni/D/Q) for comparative frequency response analysis to validate the theory. Diamond films were grown onto quartz substrates using a microwave plasma enhanced chemical vapor deposition process. Conditions were established to synthesize continuous diamond films on quartz substrates. These films were characterized by scanning …

Wavelength Modulation Spectroscopy With Diode Lasers, Ying Lu

Electrical & Computer Engineering Theses & Dissertations

Wavelength Modulation Spectroscopy is a non-intrusive technique which enables several parameters such as concentration, velocity, and temperature of a target specie to be measured. The method involves a modulation of a probe laser beam and detection at the fundamental, or any harmonic frequency, by a phase-sensitive apparatus. The theory of wavelength modulation is discussed. Effects of the finite value of the wavelength modulation index, together with the effects of any residual amplitude modulation that often occurs simultaneously in a diode laser, are included. It is shown that there are several advantages in using detection harmonics orders greater than the second. …

A Monte Carlo Analysis Of Computerized Tomography, Karyl J. Davis

Theses and Dissertations

The purpose of this thesis was to model a computerized tomography device (CT) using Monte Carlo methods to determine the scattered radiation spectrum inside and the dose outside the suite at Wright-Patterson Medical Center and at a generic suite to non-occupational personnel. This was driven by the recent inclusion of the most recent NCRP recommended dose limits into 10CFR20 of 50 mSv, occupational; 1 mSv; non-occupational continuous exposure; and 5 mSv, infrequent exposure. The rotating fan beam of the CT was modeled for MCNP, a general-purpose Monte Carlo n-particle transport modeL The CT target was a standard human phantom defined …

Photoluminescence And Electroluminescence Of Erbium And Neodymium Implanted Semiconductors, James R. Hunter

Theses and Dissertations

Low temperature photoluminescence (PL) and electroluminescence (EL) measurements were used to study the excitation of erbium- and neodymium-implanted GaAs and Al_xGa_1-xAs (x=0. 1, 0.3) pn-junctions. The rare-earth (RE) emissions were investigated as a function of ion dose, aluminum mole fraction, laser excitation power, and applied forward bias voltage for the implanted samples. Low temperature PL was also measured from Er doped silicon grown by the metalorganic chemical vapor-phase deposition (MOCVD) method using various growth parameters.. The MOCVD-grown Si samples were studied as a function of metalorganic source temperature, silane (SiH₄) flow, growth time, and …

Combination Effects Of Irradiation And Chemical Doping On High Temperature Superconductors, Russell J. Fedewa

Honors Theses

The goal of this project is to investigate some methods that improve the critical transport current in high temperature superconductors. A superconductor is a material which can allow an electrical current to flow through it with no resistance. This makes them ideal for a wide variety of applications. Most of the present use is in science or medicine, and show promise in computer circuitry materials and electromagnetic trains. This experiment explores a means of increasing the critical current, the maximum amount of electric current that can pass, and which at present is too low to permit the use of superconductors …

Comparison Of Time-Domain Reflectometry Performance Factors For Several Dielectric Geometries: Theory And Experiments, S. V. Maheshwarla, R. Venkatasubramanian, Robert F. Boehm

Electrical & Computer Engineering Faculty Research

We propose three nontraditional dielectric geometries and present an experimental and theoretical analysis and comparison of time domain reflectometry (TDR) performances for them. The traditional geometry (the probes inserted in material of essentially infinite extent) is compared to three nontraditional geometries where the probes are affixed outside of a core sample, inside of a bore, or flat on the surface of a semi-infinite solid. Our derivation relates the velocity of electromagnetic wave propagation to the complex permittivities and permeabilities of the media and the geometry for the three nontraditional configurations. Experimental results for air, styrofoam, dry sand, wet sand of …

Optimal Wavefront Reconstruction For A Coherent Diffracted Field, William W. Arrasmith

Theses and Dissertations

In sheared coherent beam interferometric imaging, an estimate of the average reflectivity profile of the object can be computed from measurements of point to point phase differences in the far field interference pattern and a suitable phase reconstruction technique. The phase difference information is encoded in the irradiance of three identical, shifted and superimposed speckled laser beam patterns. A minimum variance phase reconstruction technique is presented to estimate the phase of the field in the measurement plane from the phase differences and evaluate its performance. Prior knowledge of the phase covariance is used in the minimum variance reconstructor. Analytic calculations …

Supralinear Photoconductivity Of Copper Doped Semi-Insulating Gallium Arsenide, K. H. Schoenbach, R. P. Joshi, F. Peterkin, R. L. Druce

Bioelectrics Publications

We report on the intensity dependent supralinear photoconductivity in GaAs:Si:Cu material. The results of our measurements show that the effective carrier lifetime can change over two orders of magnitude with variations in the intensity of the optical excitation. A threshold intensity level has been observed and can be related to the occupancy of the deep copper level. Numerical simulations have also been carried out to analyze the trapping dynamics. The intensity dependent lifetimes obtained from the simulations match the experimental data very well. Finally, based on the nonlinear intensity dependence of the effective lifetimes, a possible low‐energy phototransistor application for …

Energy-Loss Particle Identification In 2-D Silicon Drift Detectors, G. Douglas Maudlin, A. A. Rollefson, Wilfred J. Braithwaite

Journal of the Arkansas Academy of Science

A relatively new type of transducer known as the Silicon Drift Detector (SDD) has been fabricated onto thin silicon wafers. SDD operates like a miniature, high-resolution, 2-D Time-projection chamber. One of these devices can detect two dimensions of an ionizing particle's position, and its integrated electrical charge output level isproportional to the particle's energy loss through the silicon. An array ofSDD's, arranged in three coaxial cylinders, is being considered as part of an instrument surrounding the beam pipe of highly-relativistic colliding beam facility, where it would be used to simultaneously track individual paths of thousands of charged particles emerging from …

Characterization Of Piezoceramic Crosses With Large Range Scanning Capability And Applications For Low Temperature Scanning Tunneling Microscopy, J. A. Helfrich, Shireen Adenwalla, J. B. Ketterson, G. A. Zhitomirsky

Shireen Adenwalla Papers

We have developed a large amplitude piezoceramic scanner which should have numerous applications. Scanning tunneling microscopy (STM) and other scanning probe microscopies predominantly use piezoceramics for the scanning elements. Similarly adaptive optics, high resolution lithography, and micromanipulators are other examples of research which regularly utilize piezoceramic scanners. We present a new geometry for a piezoceramic scanner which allows for both high resolution (~nanometers) and large amplitude (~400 µm) displacements. The cross-shaped geometry makes it possible to produce extremely long pieces with very high tolerances. We have shown its effectiveness by using it as the major component of a low temperature …

Multispectral Detection Of Ground Targets In Highly Correlated Backgrounds, Jason E. Thomas

Theses and Dissertations

Multispectral detection methods attempt to discriminate targets in a dominant clutter background using multiple images of the same real-world scene taken in different narrow spectral bands in the infrared. Detection is possible due to the empirically observed phenomenon that the radiance of man-made objects, such as a tank or truck, often lies off the main spectral correlation axis of that of natural backgrounds. Radiometric measurements of several vehicles and a tree canopy background taken over three days in June. 1994 were used to examine the factors affecting multispectral detection. Results clearly showed that the processes which provide for higher spectral …

The Current Voltage Characteristics Of Electron Beam Controlled Thin Film Diamond Switches, Christopher Anthony Molina

Electrical & Computer Engineering Theses & Dissertations

The dark current of natural diamond thin films and the induced current due to electron-beam irradiation was measured up to a range of 7000Ncm'. The contact material was aluminum, annealed and unannealed. Switching experiments were performed with electron energies ranging from 70keV to 172keV. The switching results obtained are strongly dependent on the biasing polarity, incident electron energy, and whether the contact is blocking or Ohmic in nature. A simple model which takes traps into consideration allows us to explain the various switching responses. The range of electrons which define, in part, the switch mode was measured for one sample …