Engineering Physics Commons^™

Testing And Qualification Of Low-Voltage Power Supplies For The Atlas Tile Hadronic Calorimeter Phase-Ii Upgrade, Justice A. Jones

2026 Spring Honors Capstones Projects

The High Luminosity upgrade of the Large Hadron Collider (HL-LHC) places increased thermal and operational demands on detector electronics, requiring highly reliable power systems. The ATLAS Tile Hadronic Calorimeter (TileCal) uses low-voltage power supply (LVPS) bricks to power front-end electronics, but these units operate in inaccessible regions, making failures difficult to repair. Therefore, rigorous qualification procedures are essential. This work focuses on improving LVPS reliability through a structured burn-in process. Each unit undergoes pre-burn-in electrical verification using a Single Test Stand (STS), followed by sustained operation under load and elevated temperature, and post-burn-in requalification. Standard cooling conditions limit temperatures to …

Power-Beaming: Wireless Energy Transfer Using Lasers, Spencer L. Barnett

ATU Scholars Symposium

The objective of the project is to implement a wireless energy transfer system utilizing laser technology. This system involves modulating the laser’s beam profile and spatial distribution through precise optical manipulation. The energy transmitted by the laser is captured by a photovoltaic array, commonly referred to as a solar panel, which is engineered to convert incident photons into direct current (DC) electrical power. The current challenge is to develop a reliable wireless energy transfer mechanism capable of operating over extended distances, thereby overcoming the constraints imposed by wired connections, particularly in environments where wiring is impractical, such as in space. …

Plasma Diagnostics For Anode Cathode Plasmas And High Energy Density Physics On A Linear Transformer Driver, Robert Beattie-Rossberg

Electrical and Computer Engineering ETDs

A twelve-brick air insulated linear transformer driver (LTD) was characterized by charging to voltages ranging from 30 to 70 kV and delivering energy to two separate resistive loads. Various plasma diagnostics were built and fielded with an emphasis on the design, implementation and analysis of a Mach Zehnder interferometer, a moiré deflectometer and a spectroscopy system providing information on the temporal evolution of plasma electron density and atomic composition. Rogowski coils, XRD radiation detectors, framing camera images and time integrated DSLR images are used to further understand load conditions where current data, x ray radiation data, velocity data and instability …

Developing Positive Thermal Coefficient (Ptc) Heaters For Solar Electric Cooking, Katarina Ivana Brekalo, Andrew Shepherd

Physics

Positive Thermal Coefficients, PTCs, are materials that abruptly change in resistance in response to changes in temperature. The purpose of this experiment is to explore the viability of using the switching type ceramic PTC thermistor as a replacement for current resistive heaters. These types of PTCs have a nonlinear change in resistance with increases in temperature. This device will be used as a temperature-controlling heating element intended to power an Insulated Solar Electric Cooker (ISEC). The ISEC is designed to cook meals throughout the day for impacted communities as an alternative cooking method that doesn’t require biofuel as an energy …

Memory Module Design For High-Temperature Applications In Sic Cmos Technology, Affan Abbasi

Graduate Theses and Dissertations

The wide bandgap (WBG) characteristics of SiC play a significant and disruptive role in the power electronics industry. The same characteristics make this material a viable choice for high-temperature electronics systems. Leveraging the high-temperature capability of SiC is crucial to automotive, space exploration, aerospace, deep well drilling, and gas turbines. A significant issue with the high-temperature operation is the exponential increase in leakage current. The lower intrinsic carrier concentration of SiC (10-9 cm-3) compared to Si (1010 cm-3) leads to lower leakage over temperature. Several researchers have demonstrated analog and digital circuits designed in SiC. However, a memory module is …

Design Of Smart Trashcan, Haoran Song

Senior Theses

A smart trashcan has been designed which can bring convenience to people for throwing their garbage away during the COVID-19 pandemic. A prototype is made from cardboard to demonstrate its function. This trashcan can sense people who are coming and leaving, and it can open and close automatically. The trashcan is powered by solar energy. A solar panel is mounted on top of the trashcan supporter. This design is specifically for use in China.

An Investigation Of Diode Failure, Nicholas James Adams

Physics

Solar electricity can be used to cheaply cook food and charge electronic devices. We investigate the viability of using diodes as heating elements for insulated solar electric cooking (ISEC). In addition, information on designing and constructing ISEC compatible phone chargers and rechargeable LED lighting systems is included.

Optimizing Llrf Parameters In The Electron-Ion Collider, William M. Bjorndahl

Physics

To improve particle interaction in the future Electron-Ion Collider (EIC), we investigated different feedback implementations to control the accelerating voltage and examined the power and beam phase for each instance. Using MATLAB, we studied three feedback mechanisms: Direct, One Turn, and Feedforward. Enacting feedforward yielded the best performance. To minimize the klystron power consumption, we analyzed different Low-Level Radio Frequency (LLRF) parameters such as detuning. Combining theory and simulated results, we found the optimal detuning value that minimizes klystron power consumption.

Dual-Axis Solar Tracker, Bryan Kennedy

All Undergraduate Projects

Renewable energies, and fuels that are not fossil fuel-based, are one of the prolific topics of debate in modern society. With climate change now becoming a primary focus for scientists and innovators of today, one of the areas for the largest amount of potential and growth is that of the capturing and utilization of Solar Energy. This method involves using a mechanical system to track the progression of the sun as it traverses the sky throughout the day. A dual-axis solar tracker such as the one designed and built for this project, can follow the sun both azimuthally and in …

Exploring The Electrical Properties Of Twisted Bilayer Graphene, William Shannon

Senior Theses

Two-dimensional materials exhibit properties unlike anything else seen in conventional substances. Electrons in these materials are confined to move only in the plane. In order to explore the effects of these materials, we have built apparatus and refined procedures with which to create two-dimensional structures. Two-dimensional devices have been made using exfoliated graphene and placed on gold contacts. Their topography has been observed using Atomic Force Microscopy (AFM) confirming samples with monolayer, bilayer, and twisted bilayer structure. Relative work functions of each have been measured using Kelvin Probe Force Microscopy (KPFM) showing that twisted bilayer graphene has a surface potential …

Manufacturing And Testing The Permanent Magnet Linear Motor, Renjie Kang

Senior Theses

Controlled mechanical motion is vital in many useful applications in technology. Among them, linear motors have advantages over traditional rotating motors. In this work, we built a permanent magnet linear motor to test and measure its energy efficiency. A maximum 29% total energy efficiency, and 67% energy transfer rate, were detected. In addition, a C-shape support structure was added to the moving part in order to increase the moving accuracy. The tests show that, with the support structure, the fluctuation in the vertical direction decreases significantly, but the friction of the system slightly increases.

Investigation Of The Skin Effect In Alternating Currents, Matthew Liang

The International Student Science Fair 2018

My research is on the investigation of the skin effect in alternating currents. The skin effect is when an alternating current tends to flow on the surface of the conductor, such that the current density is highest near the surface, and decreases with greater depths in the conductor. This is due to the alternating current inducing changing magnetic fields, which in turn induces currents that oppose the original flow of current, resisting the current flowing through the centre the most. This reduces the effective cross-sectional area of the conductor and increases the resistance, causing increased power losses. This effect becomes …

Investigation Of The Skin Effect In Alternating Currents, Matthew Liang

The International Student Science Fair 2018

My research is on the investigation of the skin effect in alternating currents. My project is broken down into 4 sub-aims. The first aim would be, to be able to mathematically model the distribution of current in the radius of the wire, which consists of the applications of the Maxwell equation and solving zeroth order differential Bessel equations of the first kind. The next aim would be to computationally plot out the desired current readings as the depth of the wire increases from the surface, using the Matlab software. The third aim that I have would be conducting an experiment, …

Energy Conversion System For Travelers (Ecost), Thipok Bovornratanaraks

The International Student Science Fair 2018

We have innovated “The Energy Conversion System for Travelers” or the ECoST. With the fact that most travelers have wheeled cabin-bags, whilst walking, the wheels will rotate so why don’t we harvest electricity from this kinetic energy? We thus install our innovation, the ECoST, to the bag to generate electricity from the spinning wheels. The electricity is then kept in the storage unit and ready to charge your empty battery devices in an emergency case via a USB port. To make life easy, our ECoST was designed to replicate the power bank charging method; therefore, we can charge …

Increasing The Longevity Of Tungsten Filaments In A Zone Refiner, Byron D. Greenlee

Senior Theses

Zone refining is used for its ability to purify material and grow single crystals. To produce these single crystals, a suspended molten zone, generated by electron bombardment, passes along the polycrystalline stock. During a zone refining run, the filaments that produce the electron bombardment can fail. In this project, the longevity of tungsten filaments in a zone refiner was investigated. A new bombardment geometry was constructed to attempt to increase the longevity of the filaments. The new geometry had a shield machined into it to prevent line-of-sight impurities originating in the molten zone from striking the filaments. It was found …

Measuring The Double Layer Capacitance Of Electrolyte Solutions Using A Graphene Field Effect Transistor, Agatha Ulibarri

Senior Theses

When operating graphene field effect transistors (GFETs) in fluid, a double layer capacitance (C_dl) is formed at the surface. In the literature, the C_dl is estimated using values obtained using metal electrode experiments. Due to the distinctive electronic and surface properties of graphene, there is reason to believe these estimates are inadequate. This work seeks to directly characterize the double layer capacitance of a GFET. A unique method for determining the C_dl has been implemented, and data has been obtained for three electrolytes and one ionic fluid. The results yield dramatically lower C_dl values than …

Measuring The Double Layer Capacitance Of Electrolytes With Varied Concentrations, Geoffrey Rath

Senior Theses

When electric potentials are applied from an electrolytic fluid to a metal, a double layer capacitor, C_dl, develops at the interface. The layer directly at the interface is called the Stern layer and has a thickness equal to roughly the size of the ions in the fluid. The next layer, the diffuse layer, arises from the gathering of like charges in the Stern layer. This layer is the distance needed for ionic charges to return to equilibrium. This distance, called the Debye length, λ, depends on the square root of the electrolyte concentration. To study the properties of …

Solar Powered Single-Axis Heliostat Active Solar Tracking Device, Mason Kyle Roberts

Physics

As a means of cooking food, the burning of biomass accounts for over 4 million premature deaths in third world countries (“Household Air Pollution and Health”). The focus of this project was to explore an alternative that could utilize focused sunlight to cook food. A solar tracker was designed to be affixed to a parabolic, reflective, tilted single axis heliostat to follow the sun throughout the day and focus the reflected light to the bottom of a cooking surface. This surface became hot enough to for the preparation of food or boiling/sterilization of water.

A goal for each project was …

Operating Temperature Of A Solar Thermal Stirling Engine, Spencer Beck

Senior Theses

This paper explores the relationship between the operating temperature and electricity production of a simple heat engine. A Stirling engine was designed and constructed which runs on solar thermal energy collected by a Fresnel lens. The surface area of the solar collector was varied. This manipulated the operating temperature of the Stirling engine in order to measure power output. The mechanical energy from the engine was converted to electricity using a DC motor running in reverse, acting like a generator, in conjunction with an Arduino for data collection. Although adjustments must be made in order to improve the efficiency of …

Are Solar Panels A Viable Power Source For A Green Energy Vehicle?, Mason C. Adams

Senior Theses

A solar cell powered go-kart has been built and tested. The result shows using solar energy alone cannot meet the requirement of running a regular passenger car. This is due to the limited surface area of the passenger car. This thesis also discusses the operating principles of solar panels, the physics of P type and N type semiconductors, and the formation of the PN junction, as well as the solar current. Modifications of an existing go-kart are described in detail in this thesis. Suggestions for making green vehicles are discussed as well.

Reflective Efficiencies Of Materials For Applications Of Bifacial Solar Cells, Michael Metter

Senior Theses

The bifacial solar cell is superior to its monofacial predecessor due to its ability to convert both incident light on top and reflected light from below into energy. The scattering of the reflected light is affected by the property of the material on which it is interacting. To date, little work has been contributed to studying the properties of these materials to determine optimal quantities for bifacial solar cells. In the first experiment, reflective efficiencies compared to the angle of reflection were explored for different grit of sandpaper in order to develop an understanding of how surface texture impacts reflectivity. …

Temporary Bonding With Polydimethylglutarimide Based Lift Off Resist As A Layer Transfer Platform, T. Matsumae, A. D. Koehler, J. D. Greenlee, T. J. Anderson, H. Baumgart, G. G. Jernigan, K. D. Hobart, F. J. Kub

Electrical & Computer Engineering Faculty Publications

Bonding of lift off resist (LOR) was performed to realize temporary wafer bonding without residue. Bonding process conditions such as spin speed, pre-bake temperature, and bonding temperature were optimized to obtain a large bonded area with high bond strength. Under optimized process conditions, a bonded area covering over 98% of the wafer surface, with a room temperature bond strength of nearly 5 J/m² is achieved. During razor blade testing, fracture often occurs at the Si wafer. Moreover, debonding using an N-Methyl-2-pyrrolidone (NMP)-based solvent left the wafer surface extremely small amount of residue. Thus, the optimized bonding processed developed in …

A Prototype Microwave Cavity Control Circuit For Use In Next Generation Free Electron Laser, Josh Thompson, Peter Neal Barrina, Jiayi Jiang, Joe Frisch, Steve Smith, Daniel Van Winkle

STAR Program Research Presentations

One of the current programs at SLAC National Accelerator Laboratory is the Linac Coherent Light Source, or LCLS. Using the existing hardware of the last third of their linear accelerator (or “linac”), SLAC has created one of the most energetic X-ray free electron lasers (or “FEL”). Since 2009, LCLS has used this FEL to perform a wide range of experiments across all sciences, most notably ultrafast filming at the molecular scale. As requests for beam-time with this laser increases, SLAC is purposing a linac upgrade to better match this demand. This upgrade, named LCLS-II, will replace existing copper radio frequency …

Experimental Determination Of Electron-Hole Pair Creation Energy In 4h-Sic Epitaxial Layer: An Absolute Calibration Approach, S. K. Chaudhuri, K. J. Zavalla, K. C. Mandal

Faculty Publications

No abstract provided.

Solar Light Bulb, David G. Guzman, Virgilio Gonzalez

COURI Symposium Abstracts, Summer 2012

The Solar Lighting project is a work driven towards building a low-cost and environmental-friendly solar bulb and to understanding the science behind its behavior. A solar light bulb refers to a device capable of absorbing and transferring solar energy to light up an enclosed area. By using the physical properties of fluids and light is possible to manipulate solar light waves to illuminate an enclosed structure. Moreover, this project attempts to utilize recycled materials that reduce the cost of such device, helping not only the planet but also the costumer’s pocket. The ultimate goal for this project is to scientifically …

Simulation Of Temperature Distributions In Tissue Upon Laser Pulse Irradiation Including Water Mass Transfer, Deepthi Nagulapally

Electrical & Computer Engineering Theses & Dissertations

Lasers, due to their unique characteristics, have tremendous applications in the medical field. Generally all laser applications in hie-medicine involve the propagation of laser energy through tissue. Energy is deposited giving rise to many physical, hie-chemical, and mechanical effects. Among these are dynamical changes in the local temperature distributions within the tissue. Analysis of the temperature changes requires the creation of an appropriate optical transmission and heat flow model that incorporates user specified laser parameters. Here, a numerical simulation model was developed to study both steady state and time dependent temperature distributions due to pulsed laser radiation within user specified …

Cuin1-Xalxse2 Thin Films And Solar Cells, P. D. Paulson, M. W. Haimbodi, S. Marsillac, R. W. Birkmire, W. N. Shafarman

Electrical & Computer Engineering Faculty Publications

CuIn[sub 1-x]Al[sub x]Se[sub 2] thin films are investigated for their application as the absorber layer material for high efficiency solar cells. Single-phase CuIn[sub 1-x]Al[sub x]Se[sub 2] films were deposited by four source elemental evaporation with a composition range of 0≤x≤0.6. All these films demonstrate a normalized subband gap transmission >85% with 2 µm film thickness. Band gaps obtained from spectroscopic ellipsometry show an increase with the Al content in the CuIn[sub 1-x]Al[sub x]Se[sub 2] film with a bowing parameter of 0.62. The structural properties investigated using x-ray diffraction measurements show a decrease in lattice spacing as the Al content increases. …

High-Efficiency Solar Cells Based On Cu(Inal)Se[Sub 2] Thin Films, S. Marsillac, P. D. Paulson, M. W. Haimbodi, R. W. Birkmire, W. N. Shafarman

Electrical & Computer Engineering Faculty Publications

A Cu(InAl)Se₂solar cell with 16.9% efficiency is demonstrated using a Cu(InAl)Se₂thin film deposited by four-source elemental evaporation and a device structure of glass/Mo/Cu(InAl)Se₂/CdS/ZnO/indium tin oxide/(Ni/Algrid)/MgF₂. A key to high efficiency is improved adhesion between the Cu(InAl)Se₂ and the Mo back contact layer, provided by a 5-nm-thick Ga interlayer, which enabled the Cu(InAl)Se₂ to be deposited at a 530 °C substrate temperature. Film and device properties are compared to Cu(InGa)Se₂ with the same band gap of 1.16 eV. The solar cells have similar behavior, with performance limited by recombination through …

Development And Testing Of An Ac Micro Hollow Cathode Simulator, Thomas E. Caldwell

Electrical & Computer Engineering Theses & Dissertations

The use of AC source plasma discharge devices in applications such as material processing and film deposition has increased in recent years due to improvements in discharge efficiency made possible by devices such as the micro hollow cathode. Designing hollow cathodes for specific applications requires an understanding of the processes that govern the discharge. Simulation is an inexpensive tool for understanding hollow cathode operation and optimizing the device for specific applications. This thesis describes the development of an AC micro hollow cathode simulator. It details the theoretical models used in the simulation and presents the results of test cases intended …

Electrical Characteristics And Parallel Operation Of Microhollow Cathode Discharges, Wenhui Shi

Electrical & Computer Engineering Theses & Dissertations

This thesis describes the electrical properties of microhollow cathode discharges with argon as filling gas. The appearance and current-voltage characteristics of microhollow cathode discharges have been recorded. Three kinds of discharge modes (predischarge, hollow cathode discharge and abnormal discharge) have been observed. The range of operation of the hollow cathode discharge has been found to be 0.5 < pD & 5 Torr cm in argon. By reducing the hole diameter to 100 pm, we were able to operate the discharge to atmospheric pressure in a dc mode. The possibility of dc parallel operation of microhollow cathode discharges was explored. Parallel operation could be obtained without individual ballast for discharges with a positive I-V slope greater than 10 V/mA over a voltage range of more than 5 % of the sustaining voltage. For parallel operation outside the range the ballasting is required. This model was explored by using a segmented anode model. The result of the simple calculation coincides well with the experiment result, where a semi-insulator silicon was used as distributed ballast.