Engineering Physics Commons^™

Magnetocrystalline Anisotropy Of "-Fe2o3, Imran Ahamed, Rohilt Pathak, Arti Kashyap

Nebraska Center for Materials and Nanoscience: Faculty Publications

The epsilon Fe₂O₃ phase of iron oxide has been studied to understand the spin structure and the magnetocrystalline anisotropy in the bulk and in thin films of "-Fe₂O₃ and Co-doped "-Fe₂O₃. The preferential magnetization direction in the nanoparticles of "-Fe₂O₃ is along the a-axis [M. Gich et al., Chem. Mater. 18, 3889 (2006)]. Compared to the bulk band gap of 1.9 eV, the thin-film band gap is reduced to 1.3 eV in the Co-free films and to 0.7 eV in the film with partial …

Texture Development And Coercivity Enhancement In Cast Alnico 9 Magnets, Wenyong Zhang, Shah Valloppilly, Xingzhong Li, Lanping Yue, Ralph Skomski, Iver Anderson, Matthew Kramer, Wei Tang, Jeff Shield, David J. Sellmyer

Nebraska Center for Materials and Nanoscience: Faculty Publications

The effect of Y addition and magnetic field on texture and magnetic properties of arc-melted alnico 9 magnets has been investigated. Small additions of Y (1.5 wt.%) develop a (200) texture for the arc-melted alnico 9 magnet. Such a texture is hard to form in cast samples. To achieve this goal, we set up a high-field annealing system with a maximum operation temperature of 1250⁰ C. This system enabled annealing in a field of 45 kOe with subsequent draw annealing for the solutionized buttons; we have been able to substantially increase remanence ratio and coercivity, from 0.70 and 1200 …

An Application Of M-Matrices To Preserve Bounded Positive Solutions To The Evolution Equations Of Biofilm Models, Richard S. Landry Jr.

LSU New Orleans Theses and Dissertations

In this work, we design a linear, two step implicit finite difference method to approximate the solutions of a biological system that describes the interaction between a microbial colony and a surrounding substrate. Three separate models are analyzed, all of which can be described as systems of partial differential equations (PDE)s with nonlinear diffusion and reaction, where the biological colony grows and decays based on the substrate bioavailability. The systems under investigation are all complex models describing the dynamics of biological films. In view of the difficulties to calculate analytical solutions of the models, we design here a numerical technique …

Flow Anisotropy Due To Thread-Like Nanoparticle Agglomerations In Dilute Ferrofluids, Alexander Cali, Wah-Keat Lee, A. David Trubatch, Philip Yecko

Department of Applied Mathematics and Statistics Faculty Scholarship and Creative Works

Improved knowledge of the magnetic field dependent flow properties of nanoparticle-based magnetic fluids is critical to the design of biomedical applications, including drug delivery and cell sorting. To probe the rheology of ferrofluid on a sub-millimeter scale, we examine the paths of 550 μm diameter glass spheres falling due to gravity in dilute ferrofluid, imposing a uniform magnetic field at an angle with respect to the vertical. Visualization of the spheres’ trajectories is achieved using high resolution X-ray phase-contrast imaging, allowing measurement of a terminal velocity while simultaneously revealing the formation of an array of long thread-like accumulations of magnetic …

Trigger And Noise Filtering Algorithms For The Lhaaso Water Cherenkov Detector Array, Xiao Jie Wang, Zhi Guo Yao, Min Zha, Ming Jun Chen, Bo Gao, De Zhi Huang, Hui Cai Li, Jin Yan Liu, Wen Ying Liao, Han Rong Wu

Physics Faculty Research & Creative Works

Introduction: The Large High Altitude Air Shower Observatory (LHAASO) will be constructed at Mt. Haizishan, Sichuan Province, China. Among several detector components of the LHAASO, the Water Cherenkov Detector Array (WCDA) is of great importance for gamma-ray astronomy from 100 GeV to 30 TeV. The single-channel counting rate of a photo- multiplier tube can reach as high as 30 -35 kHz, most of them are background noise hits from the low energy cosmic ray showers, bringing a big challenge on data transferring, data storage and event reconstruction. Methods: In this paper, a dedicated trigger scheme and a fast noise filtering …

Artificial Olfactory System For Multi-Component Analysis Of Gas Mixtures., Alexander Aleksandrovich Larin

Electronic Theses and Dissertations

Gas analysis is an important part of our world and gas sensing technology is becoming more essential for various aspects of our life. A novel approach for gas mixture analysis by using portable gas chromatography in combination with an array of highly integrated and selective metal oxide (MOX) sensors has been studied. We developed a system with small size (7 x 13 x 16 inches), low power consumption (~10 W) and absence of special carrier gases designed for portable field analysis (assuming apriori calibration). Low ppb and even sub-ppb level of detection for some VOCs was achieved during the analysis …

Rogue Rotary - Modular Robotic Rotary Joint Design, Sean Wesley Murphy, Tyler David Riessen, Jacob Mark Triplett

Mechanical Engineering

This paper describes the design process from ideation to test validation for a singular robotic joint to be configured into a myriad of system level of robots.

Characterization Of Laser-Generated Aluminum Plasma Using Ion Time-Of-Flight And Optical Emission Spectroscopy, Md. Haider A. Shaim, Hani E. Elsayed-Ali

Electrical & Computer Engineering Faculty Publications

Laser plasma generated by ablation of an Al target in vacuum is characterized by ion time-of-flight combined with optical emission spectroscopy. A Q-switched Nd:YAG laser (wavelength λ = 1064 nm, pulse width τ ∼ 7 ns, and fluence F ≤ 38 J/cm²) is used to ablate the Al target. Ion yield and energy distribution of each charge state are measured. Ions are accelerated according to their charge state by the double-layer potential developed at the plasma-vacuum interface. The ion energy distribution follows a shifted Coulomb-Boltzmann distribution. Optical emission spectroscopy of the Al plasma gives significantly lower plasma temperature …

University Of Minnesota Smallsat And High Altitude Ballooning Development And Collaboration, Luke Zumwalt, Ricardo Saborio, Athanasios Pantazides, Aaron Nightingale, Demoz Gebre Egziabher, Lindsay Glesener

2017 Academic High Altitude Conference

The Experiment for X-ray Characterization and Timing (EXACT) mission is a 3U CubeSat technology-development project being built by the SmallSat team at the University of MN – Twin Cities which is a joint research effort of the Aerospace Engineering and Mechanics (AEM) Department and the School of Physics and Astronomy (SPA). The main objective of this spacecraft is to carry a payload including a detector designed to measure energy and time of arrival time of individual hard x-ray photons emitted from the Sun and from other astrophysical sources. During the development process for EXACT, flights provided by the High-Altitude Student …

Measurement Of Speed Of Sound Profile Using Laaces Balloon, Zhuang Li, Brett Schaefer, Brian Schaefer, William Dever, Tyler Morgan, Matthew Foltz

2017 Academic High Altitude Conference

The goal of this mission is to test the speed of sound at different altitudes and ultimately at a maximum height of 100,000 feet (30 km). In conjunction with this testing, environmental parameters including temperature, pressure, and humidity are measured and used to calculate the speed of sound to compare to the measured results. The team constructed the payload “Dorothy” using polystyrene foam due to its lightweight and thermal isolation property. An ultrasonic sensor with a reflection mirror were installed outside payload box to measure speed of sound. All the sensors were calibrated. Software for the project was developed in …

Calibration Of Temperature Sensors In Preparation For The 2017 Total Solar Eclipse, Erick Agrimson, Kaye Smith, Ana Taylor, Vina Onyango-Robshaw, Rachel Lang, Alynie Xiong, Peace Sinyigaya, Grace Maki, Rachel Dubose, Brittany Craig, James Flaten, Gordon Mcintosh

2017 Academic High Altitude Conference

In preparation for the 2017 total solar eclipse, St. Catherine University developed a calibration protocol for the temperature sensors flown during thermal wake boom experiments. The calibration method used a standard two-point technique that corrected each individual sensor for both slope and offset errors using a high quality NIST certified thermocouple as the temperature standard. Our method is not absolute but corrects each sensor relative to the NIST standard so that we feel some confidence that individual sensor variations are mitigated. In preparation for the eclipse, calibration curves were generated for over 200 individual digital and thermistor temperature sensors.

Pressure Regulator For A High Altitude Balloon, Kala Brown, Darci Snowden, Joe Cuthbertson, Jessica Kisner, Addison Wenger

2017 Academic High Altitude Conference

High altitude balloons are large latex balloons filled with gas that carry a payload to near space. Because they can travel to around 100,000 feet, they provide a convenient way to study the Earth’s atmosphere. Per Boyle’s Law, the pressure and volume of a confined gas are inversely proportional. Thus, as the balloon ascends and the atmospheric pressure decreases, the gas inside the balloon expands. This pressure difference allows the balloon to ascend, but it also causes it to continuously expand until it bursts. For some observations, one might want their balloon to remain at about the same altitude for …

Controlled Heading Automation Device, Robert Coulson

2017 Academic High Altitude Conference

One of the most significant limitations of weather balloon-based data collection is that instruments and payloads cannot depend on particular orientations or predictable rotation. Several investigators have used payload heading control devices to overcome this limitation in order to collect directional data and record motion controlled video footage. The work described in this presentation builds on the Controlled Heading Automation Device (CHAD) developed by Kruger et al. (2016) and was carried out at DePaul University in summer 2017 as an undergraduate research project. Our goal was to record stable video of the shadow of the moon on Earth’s surface during …

Experiential Learning Opportunity (Elo) And Utilization Of Field-And-Data- Based Information Obtained Through The Infusion Of Technology: Highlights On Nasa Stem And Earth Science Curricula, Nazrul I. Khandaker, Matthew Khargie, Shuayb Siddiqu, Sol De Leon, Katina Singh, Newrence Wills, Krishna Mahibar

Publications and Research

There is a greater emphasis on hands-on involvement and critical thinking skills in the geosciences and other STEM fields to inspire and engage K- 16 students to value scientific content and enable them to discover the well-documented nature of the fundamental scientific principles needed to explain various earth science and other STEM-related core phenomena. NASA MAA curricula are ideal for engaging K1-16 students in this context, since grade-specific lesson plans open-up a plethora of pedagogically sound and relevant earth science activities. These include earth’s materials and properties, meteorites, robotics, hot air balloon, flight simulation, star gazing, material science, crystal growth, …

An Enhanced Operational Definition Of Dielectric Breakdown For Dc Voltage Step-Up Tests, Allen Andersen, Jr Dennison

Journal Articles

The imprecise definition of breakdown in the ASTM D3755-14 standard can misidentify breakdown. If the recommended test circuit current sensing element threshold is set too high, breakdown may occur undetected. Conversely, false positives may result from designating a low current threshold. An operational definition of breakdown much less sensitive to these pitfalls is outlined herein. This enhanced definition of breakdown is based on the average rate of change of the leakage current with increasing voltage, rather than a simple current threshold, avoiding ambiguous association with anomalies in current traces. For tests that continuously monitor leakage current, breakdown can be detected …

Spin-Imbalance In A 2d Fermi-Hubbard System, Peter Brown, Debayan Mitra, Elmer Guardado-Sanchez, Peter Schauß, Stanimir Kondov, Ehsan Khatami, Thereza Paiva, Nandini Trivedi, David Huse, Waseem Bakr

Faculty Publications

The interplay of strong interactions and magnetic fields gives rise to unusual forms of superconductivity and magnetism in quantum many-body systems. Here, we present an experimental study of the two-dimensional Fermi-Hubbard model—a paradigm for strongly correlated fermions on a lattice—in the presence of a Zeeman field and varying doping. Using site-resolved measurements, we revealed anisotropic antiferromagnetic correlations, a precursor to long-range canted order. We observed nonmonotonic behavior of the local polarization with doping for strong interactions, which we attribute to the evolution from an antiferromagnetic insulator to a metallic phase. Our results pave the way to experimentally mapping the low-temperature …

Solar Powered Single-Axis Heliostat Active Solar Tracking Device, Mason Kyle Roberts

Physics

As a means of cooking food, the burning of biomass accounts for over 4 million premature deaths in third world countries (“Household Air Pollution and Health”). The focus of this project was to explore an alternative that could utilize focused sunlight to cook food. A solar tracker was designed to be affixed to a parabolic, reflective, tilted single axis heliostat to follow the sun throughout the day and focus the reflected light to the bottom of a cooking surface. This surface became hot enough to for the preparation of food or boiling/sterilization of water.

A goal for each project was …

Interplay Of Quantum Size Effect, Anisotropy And Surface Stress Shapes The Instability Of Thin Metal Films, Mikhail Khenner

Mathematics Faculty Publications

Morphological instability of a planar surface ([111], [011], or [001]) of an ultra-thin metal film is studied in a parameter space formed by three major effects (the quantum size effect, the surface energy anisotropy and the surface stress) that influence a film dewetting. The analysis is based on the extended Mullins equation, where the effects are cast as functions of the film thickness. The formulation of the quantum size effect (Z. Zhang et al., PRL 80, 5381 (1998)) includes the oscillation of the surface energy with thickness caused by electrons confinement. By systematically comparing the effects, their contributions into the …

On The Ramberg-Osgood Stress-Strain Model And Large Deformations Of Cantilever Beams, Ronald J. Giardina Jr

LSU New Orleans Theses and Dissertations

In this thesis the Ramberg-Osgood nonlinear model for describing the behavior of many different materials is investigated. A brief overview of the model as it is currently used in the literature is undertaken and several misunderstandings and possible pitfalls in its application is pointed out, especially as it pertains to more recent approaches to finding solutions involving the model. There is an investigation of the displacement of a cantilever beam under a combined loading consisting of a distributed load across the entire length of the beam and a point load at its end and new solutions to this problem are …

Characterization Of Nanoparticles Using Solid State Nanopores, Santoshi Nandivada

Graduate Theses and Dissertations

Solid state nanopores are widely used in detection of highly charged biomolecules like DNA and proteins. In this study, we use a solid state nanopore based device to characterize spherical nanoparticles to estimate their size and electrical charge using the principle of resistive pulse technique. The principle of resistive pulse technique is the method of counting and sizing particles suspended in a fluid medium, which are electrophoretically driven through a channel and produce current blockage signals due to giving rise to a change in its initial current. This change in current is denoted as a current blockage or as a …

Novel Half-Metallic And Spin-Gapless Heusler Compounds, Yunlong Jin

Department of Physics and Astronomy: Dissertations, Theses, and Student Research

This thesis is devoted to experimental studies of Heusler compounds CoFeCrAl, CoFeCrX (X = Si, Ge) and Mn₂PtSn. These Heusler alloys present an interesting class of ferromagnetic materials for spintronic applications since they are predicted to be spin gapless semiconductors and have half-metallic properties with 100 % spin polarization at the Fermi level. In this thesis, the structural, magnetic, spin-polarization and electron- transport properties of the fabricated alloys were studied. CoFeCrAl thin films deposited on MgO exhibit nearly perfect epitaxy and a high degree of L2₁ Heusler order. All considered types of chemical disorder destroy the spin-gapless …

Nanostructure Evolution Of Magnetron Sputtered Hydrogenated Silicon Thin Films, Dipendra Adhikari, Maxwell M. Junda, Sylvain X. Marsillac, Robert W. Collins, Nikolas J. Podraza

Electrical & Computer Engineering Faculty Publications

Hydrogenated silicon (Si:H) thin films have been prepared by radio frequency (RF) magnetron sputtering. The effect of hydrogen gas concentration during sputtering on the resultant film structural and optical properties has been investigated by real time spectroscopic ellipsometry (RTSE) and grazing incidence x-ray diffraction (GIXRD). The analysis of in-situ RTSE data collected during sputter deposition tracks the evolution of surface roughness and film bulk layer thickness with time. Growth evolution diagrams depicting amorphous, nanocrystalline and mixed-phase regions for low and high deposition rate Si:H are constructed and the effects of process parameter (hydrogen gas concentration, total pressure and RF power) …

Electrical Characterization Of Irradiated Semiconducting Amorphous Hydrogenated Boron Carbide, George Glen Peterson

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Semiconducting amorphous partially dehydrogenated boron carbide has been explored as a neutron voltaic for operation in radiation harsh environments, such as on deep space satellites/probes. A neutron voltaic device could also be used as a solid state neutron radiation detector to provide immediate alerts for radiation workers/students, as opposed to the passive dosimetry badges utilized today. Understanding how the irradiation environment effects the electrical properties of semiconducting amorphous partially dehydrogenated boron carbide is important to predicting the stability of these devices in operation. p-n heterojunction diodes were formed from the synthesis of semiconducting amorphous partially dehydrogenated boron carbide on silicon …

Simulation Of Alnico Coercivity, Liqin Ke, Ralph Skomski, Todd D. Hoffman, Lin Zhoue, Wei Tang, Duane D. Johnson, Matthew J. Kramer, Iver E. Anderson, C.Z. Wang

Nebraska Center for Materials and Nanoscience: Faculty Publications

Micromagnetic simulations of alnico show substantial deviations from Stoner-Wohlfarth behavior due to the unique size and spatial distribution of the rod-like Fe-Co phase formed during spinodal decomposition in an external magnetic field. The maximum coercivity is limited by single-rod effects, especially deviations from ellipsoidal shape, and by interactions between the rods. Both the exchange interaction between connected rods and magnetostatic interaction between rods are considered, and the results of our calculations show good agreement with recent experiments. Unlike systems dominated by magnetocrystalline anisotropy, coercivity in alnico is highly dependent on size, shape, and geometric distribution of the Fe-Co phase, all …

Elastic Properties Of Superconductors And Materials With Weakly Correlated Spins, Christian Binek

Christian Binek Publications

It is shown that in the ergodic regime, the temperature dependence of Young’s modulus is solely determined by the magnetic properties of a material. For the large class of materials with paramagnetic or diamagnetic response, simple functional forms of the temperature derivative of Young’s modulus are derived and compared with experimental data and empirical results. Superconducting materials in the Meissner phase are ideal diamagnets. As such, they display remarkable elastic properties. Constant diamagnetic susceptibility gives rise to a temperature independent elastic modulus for ceramic and single crystalline superconductors alike. The thermodynamic approach established in this report, paves the way to …

Instrument Design Optimization With Computational Methods, Michael H. Moore

Physics Theses & Dissertations

Using Finite Element Analysis to approximate the solution of differential equations, two different instruments in experimental Hall C at the Thomas Jefferson National Accelerator Facility are analyzed. The time dependence of density fluctuations from the liquid hydrogen (LH2) target used in the Q_weak experiment (2011-2012) are studied with Computational Fluid Dynamics (CFD) and the simulation results compared to data from the experiment. The 2.5 kW liquid hydrogen target was the highest power LH2 target in the world and the first to be designed with CFD at Jefferson Lab. The first complete magnetic field simulation of the Super High Momentum …

Perspective: The Physics, Diagnostics, And Applications Of Atmospheric Pressure Low Temperature Plasma Sources Used In Plasma Medicine, M. Laroussi

Electrical & Computer Engineering Faculty Publications

Low temperature plasmas have been used in various plasma processing applications for several decades. But it is only in the last thirty years or so that sources generating such plasmas at atmospheric pressure in reliable and stable ways have become more prevalent. First, in the late 1980s, the dielectric barrier discharge was used to generate relatively large volume diffuse plasmas at atmospheric pressure. Then, in the early 2000s, plasma jets that can launch cold plasma plumes in ambient air were developed. Extensive experimental and modeling work was carried out on both methods and much of the physics governing such sources …

Relaxation Of Microwave Nonlinearity In A Cuprate Superconducting Resonator, Richard A. Huizen, Sean L. Hamilton, Geoffrey T. Lenters, Stephen K. Remillard

Faculty Publications

The second- and third-order nonlinear microwave response of a superconducting YBa2Cu3O7 thin-film resonator was synchronously measured using three input tones. This technique permits the local measurement, and hence mapping, of intermodulation distortion inside the resonator. Second- and third-order IMD measured with a fixed probe relaxed in remarkably different ways after the removal of a static magnetic field. The second-order IMD relaxed by two different magnetic processes, a fast process that appears related to bulk remanent magnetization and a slow process that fits the description of Bean and Livingston. The third-order IMD relaxes by only one process that is distinct from …

The Magnetic, Electrical And Structural Properties Of Copper-Permalloy Alloys, Makram A. Qader, A. Vishina, Lei Yu, Cougar Garcia, Rakesh K. Singh, Nicholas D. Rizzo, Mengchu Huang, Ralph Chamberlin, Kirill Belashchenko, Mark Van Schilfgaarde, N. Newman

Kirill Belashchenko Publications

Copper-permalloy [Cu_1–x(Ni₈₀Fe₂₀)_x] alloy films were deposited by co-sputtering and their chemical, structural, magnetic, and electrical properties were characterized. These films are found to have favorable weak ferromagnetic properties for low temperature magnetoelectronic applications. Our results show that by varying the composition, the saturation magnetization (M_s) can be tuned from 700 emu/cm³ to 0 and the Curie temperature (T_c), can be adjusted from 900 K to 0 K. The M_s and T_c are found to scale linearly between x = 25% and 100%. Electronic structure calculations …

Operating Temperature Of A Solar Thermal Stirling Engine, Spencer Beck

Senior Theses

This paper explores the relationship between the operating temperature and electricity production of a simple heat engine. A Stirling engine was designed and constructed which runs on solar thermal energy collected by a Fresnel lens. The surface area of the solar collector was varied. This manipulated the operating temperature of the Stirling engine in order to measure power output. The mechanical energy from the engine was converted to electricity using a DC motor running in reverse, acting like a generator, in conjunction with an Arduino for data collection. Although adjustments must be made in order to improve the efficiency of …